Search Documents

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By J. Leja, A. Pomianowski

This paper deals with equimolar solutions of xanthate and alkyl trimethyl ammonium bromide adsorption on copper, nickel and sphalerite powders. After an exposition of the experimental methods used and the results obtained, a thorough discussion leads to the conclusion that some molecular association between xanthates and CnTAB's does take place in the bulk of the solution as well as at the air/liquid interface. A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 to 400 mµ) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed, the half life of which was established as 29±3 days at 22°C and pH ~ 6. In mixed solutions of longer xanthate homologues (e.g. hexyl and nonyl) and equimolar CnTAB, colloidal precipitates are gradually formed which contain primarily the corresponding xanthate molecules. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 to 10"3 M solutions of KEtX alone and in equimolar mixtures of KEtX and CI2TAB. Presence of C12TAB caused a two to three fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and nickel powders (and in their rates of abstraction) but had no effect on the abstraction of xanthate by unactivated sphalerite (equivalent to less than a monolayer). The adsorption of C12TAB itself from the mixed solutions was very low, at most one monolayer only, and was not influenced by the nature of the solid powder used. A change in the rates of abstraction, observed with copper powder, was interpreted as a completion of a multilayer coating (completely enveloping the grains of powder) following which the rate of reaction between solution and substrate becomes controlled by diffusion through this coating. Work of Buckenham and Schulmanl on molecular associations between different collectors has shown unusual synergistic effects in flotation of individual minerals using mixtures of xanthates and alkyl trimethyl ammonium bromides. The objectives of the present work were: 1) to determine whether these molecular associations between the two types of collectors (indicated by strong surface tension lowering in Buckenham and Schulman's work) take place at the air/liquid interface only or in the bulk of solution as well 2) to establish whether different solids adsorb any species from the mixture of these amphipatic molecules preferentially or as molecular complexes 3) to establish whether there are any differences in the kinetics of adsorption. Metallic copper and sphalerite powder were chosen as adsorbents since they represent two extremes since copper readily adsorbs multilayers of xanthate (and is easily floated with ethyl xanthate) while unactivated sphalerite does not appreciably adsorb xanthate but is known to be readily floated by the amine type collectors. Metallic nickel was included because the infrared spectroscopic work2 on xanthate

Jan 1, 1964

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By C. K. Leith

THE purpose of these conferences has been to find some basic principles to guide us in the chaos which confronts us, to arrive at elements of a national policy. None such exists, nor, as a matter of fact, have there been any concerted efforts by the public or the mineral industry to evolve one. In the absence of such a policy the administrative agencies of the government can hardly be expected to be consistent or really effective in their handling of mineral problems, domestic or foreign. Basic Facts MINERAL reserves are unequally distributed among the nations. The principal world supplies are grouped around the north Atlantic, and nearly three-fourths of the world's total is controlled politically and commercially by English-speaking people. No one nation has a complete supply of the minerals necessary for modern industry; specialization, reciprocity, and large-scale movements between the nations are inherent in nature's unequal distribution of them. The principal sources of supply are relatively few compared with the nations to be served-a fact which determines broadly certain natural outlines of the world flow. National isolation with regard to minerals can be accomplished only through backward steps in industry and lower standards of living even in the nations possessing the most of the mineral supplies. A certain measure of unified commercial control, international in scope, is a natural consequence of the limited number of the large sources of supply. Mineral supplies for the world as a whole are so large that there is little need for concern about early exhaustion, but every nation has important problems of early exhaustion of particular minerals, which must affect their policies.

Jan 1, 1933

Jan 1, 1909

By E. T. Stephenson

Wert and Marx1 pointed out that a straight-line relationship exists between the activation energy of a relaxation process and the temperature at which the maximum relaxation occurs. The data available at the time indicated that this relationship held for a number of Snoek peaks, several grain boundary peaks, and pair relaxation in a brass. Theoretical justification for the observed relationship was found in the following equation, which Wert and Marx derived from the theory of interstitial atomic diffusion coefficients:' where AH is activation energy, R is the gas constant, T is the internal friction peak temperature, v is the interstitial atomic frequency, f is the frequency of the applied stress, S is entropy of activation. More accurate internal-friction data on interstitial diffusion in bcc metals have become available since Wert and Marx's paper. Table I gives activation energies calculated by several authors from a combination of elastic aftereffect data and the peak temperatures at several frequencies of measurement. (In the case of Fe-C and Fe-N, the referenced authors5'7'8'10 also used high-temperature diffusion data.) However, diffusion experiments at 150°C and above1'-13—rather than anelastic techniques—were used to determine the activation energy of hydrogen diffusion in Fe-H. In order to plot this recent data as a AH vs T graph we calculated the peak temperatures of the systems listed in Table I (with the exception of Fe-C, Fe-N, and Fe-H) by using published values3'' of AH and Do. These calculated peak temperatures varied by only a few degrees from experimentally determined peak temperatures. The calculated values were felt to represent the better average. A number of investigators have found the peak temperatures in Fe-C and Fe-N to be 38 to 40°C and 20° to 24°C, respectively. The values of 39" and 22°C (312° and 295°K in Table I) were determined by carefully executed experiments.6'8 The hydrogen peak temperature has been measured at 1 cps,12 20 cps,14 and 35,000 cps.15 All hydrogen peak temperatures were adjusted to 1 cps for Table I using AH = 3000 cal per mole. As Fig. 1 shows, the data of Table I fit a straight line at least as well as the earlier data used by Wert and Marx. Linear-regression analysis was applied to the data in Table I. The Fe-H data was omitted because the activation energy has not been experimentally determined in the temperature range of the peak. The analysis yields the equation: with a standard error of 860 cal per mole. The agreement of the data in Table I with the Wert-Marx equation is excellent. Strict application of Eq. [I] forces the linear regression analysis through the origin. In this case, the analysis gives a slope of 62.1 cal per mole per deg, and a standard error of *890 cal per mole. With this value, it follows from internal-friction theory that Hence, Do varies by only 30 pct among these bcc-interstitial systems. Thus, a concept suggested originally by Wert and Marx1 is confirmed by recently published data. The

Jan 1, 1965

By B. L. Averba

THE determination of retained austenite by X-ray diffraction uses the following relationship:"" Pa = constant . RVaA (8) [1] where: P is the diffracted power from phase a; R, the calculated intensity factor; A, the absorption correction; 8, the diffraction angle; and Va, the irradiated volume of phase a For a flat sample making a glancing angle + with the incident beam the absorption correction is calculated as: * 1 sin (28 - 4) A .= 1 [2] µ sin, (28 — 4) + sin 4 where µ is the linear absorption coefficient. Beu3 has proposed that the computed absorption correction be combined with the constant and that the experimental observation of the absorption correction used in the original method be eliminated. This procedure is permissible only if: 1—There is no preferred orientation in the sample, and 2—The geometric requirements have been met precisely. If these conditions are not met the validity of the determination is questionable. Unfortunately the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2. In practice it may be convenient to plot P/R vs the parameter sin (2? — )[sin (28 — +) + sin +] to obtain straight lines for the ap- parent absorption correction. Deviations from straight lines indicate either that the sample has not been positioned correctly or that the relative intensities are incorrect. Geiger counter spectrometer methods also have been used successfully for retained austenite determinations. In the usual spectrometer arrangement the sample makes equal angles with the incident and diffracted beams (8 = ); thus the absorption correction is simply 1/2µ and independent of 8. The retained austenite is then easily calculated from integrated intensity measurements on austenite and martensite lines. If the austenite content is not too low and if excessive fluorescence is not encountered it is possible to use filtered radiation and a recording spectrometer. The integrated intensities are then proportional to the areas of the diffraction peaks. For lower austenite contents the following technique was used: A bent quartz monochromator and a Geiger counter spectrometer are employed. The monochromatic radiation is focused on the front slit, and the counter slit is made broad enough to include the entire line. A series of readings are taken in the vicinity of the diffraction peak. The highest reading includes the diffraction line plus background. The background is obtained from the average of several readings on each side of the peak. The integrated intensity is obtained by subtraction. CrK, and FeKa have been used for such determinations. This technique has been found to be as sensitive and as accurate as the photographic methods. In the spectrometer methods the ratio austenite/ martensite may be obtained from readings on austenite and martensite lines and the application of Eq. 1. It is also possible to use external standards and to obtain the austenite contents from measurements on the austenite lines alone. The small correction for carbides then becomes unnecessary. The best standards are probably samples with known

Jan 1, 1954

By D. W. Fuerstenau

MEASUREMENT of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions.1,2 Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus." The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes. The assembled apparatus is shown schematically in Fig. 2. To eliminate CO2 from the solutions, all experiments are conducted in a nitrogen atmosphere. Nitrogen, used to drive solutions through the plug, is passed through a bottle of concentrated KOH solution to remove CO2 (9). A 9-liter ballast reservoir (10) is used to maintain a more nearly uniform pressure. A series of stopcocks controls the direction of flow nitrogen to the flasks (11). Tubes of as-carite prevent backflow of CO2 into the system (12). Driving pressure, which can be set at any desired value, is measured with either a water manometer (13) or a mercury manometer (14). Reservoir flasks have side arms for making pressure corrections for the difference in water levels in the flasks. Streaming potentials are measured by the circuit illustrated in Fig. 2. The electrodes from the plug are connected through mercury wells (15) to a reversing switch (16), which reverses the polarity of the electrodes depending on the direction of flow of solution through the plug. The streaming potential is measured with a Leeds and Northrup type K2 potentiometer (17). Proper choice of null instrument is important because Eq. 1 assumes that the current which escapes through the measuring instruments is negligible. An ordinary galvanometer cannot be used to determine the null point because

Jan 1, 1957

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult's law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager' from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult's law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d'Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,' the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By W. R. Bull, J. R. Roos

A method is described whereby the true financial value of each constituent of each concentrate can be calculated. Each value is then compared with what this value would be in a perfect separation. The difference in each case represents the loss incurred by each aspect of an inefficient separation. The relative magnitudes of these losses indicate those avenues of plant investigation and research that offer the highest potential reward. The metallurgical efficiency of a concentration operation is difficult to express because there are two criteria of performance, namely, grade and recovery. Neither of these alone gives any indication of the effectiveness of an operation and, if they are combined in some formula, it must be empirical and unreliable because of many external factors. Since milling is an operation performed as one step in the most profitable overall method of producing a metal or other end product, the main objective of mill operation should be to make a maximum contribution to this maximum profit. When concentrates are sold to custom smelters, the income from the operation, and the costs, may be calculated. When concentrates are further processed by another division of the same company, and there is no formal financial relationship between, say, the milling and smelting divisions of the company, the mill superintendent's job is less well defined. But even so, if the mill superintendent works as though he were selling his concentrates, and uses reasonable, if fictitious, conditions of sale, then he can get a good indication of the effectiveness of his operation by calculating his "Economic Recovery". ECONOMIC RECOVERY This is a method used as a basis of operation by several mills and has been described in the literature. Very briefly, the "standard" of operation is taken as that of a mill separating the ore into perfectly pure concentrates with 100% recovery of each mineral in its respective concentrate. For example, a 4%Pb, 4% Zn ore (galena and sphalerite), would provide a lead concentrate weighing 4.62% of the feed and assaying 86.6% Pb and a zinc concentrate weighing 5.97% of the feed and assaying 67.1 % zinc. These perfect concentrates are (hypothetically) shipped to the appropriate smelters, freight and treatment charges and payments calculated, and the net return obtained. This is the optimum financial return for the operation of the mill and is used as the standard. Now the return for the actual, real-life, mill operation is calculated in the same way, and the ratio of the two is termed the Economic Recovery. Many additions and modifications may be made in any particular case. For example, if the zinc mineral is marmatite, the optimum grade of the zinc concentrate may be set lower than 67.1%. If silver is present, it will be recovered 100% in the lead concentrate in the perfect operation. Similarly, cadmium will be recovered 100% with the sphalerite. Mr. Weiss' paper' mentions a case where, because of extremely fine intergrowth between the valuable mineral, chalcocite, and pyrite, the optimum grade of copper concentrate was taken as 45% Cu instead of the theoretical 80%. Each operation will present its own possibilities in this way.

Jan 1, 1970

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,' experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.' Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By R. G. Hudson, L. Yang

In electrochemical separation of metals, it is necessary to control the potential applied between the electrodes so that only the desired electrode reactions can occur. A knowledge of the minimum potential needed for a given electrode reaction to take place continuously is therefore pertinent to the success of the process. In molten chloride systems at high temperatures, activation polarization is believed to be small,1,2 so the minimum potential needed for the electrolytic decomposition of a molten metal chloride MC1n (n = valence of the metal ion) is therefore essentially the equilibrium electrode potential E of the metal-chlorine galvanic cell in the solution. If the decomposition products are pure M and chlorine at a pressure of p atm, E*Eo-rt/nf in [i] Since EO (the standard electrode potential of MCln) is a constant at a given temperature and R (the gas constant), and F (the Faraday's constant) are all constants, the variation of E with the electrolytic bath conditions is largely determined by the effect of the latter on the activity of the metal chloride amcln (standard state = pure MC1,). Measurement of E and study of how amCin varies with temperature and concentration, the nature of the solvent, and that of the coexisting solutes are therefore pertinent in the selection of optimum operating conditions for the electrochemical separation of metals. Because of its low melting point, high decomposition potentials of its components, and the low solubility of heavier metals in it, the LiC1-KC1 eutectic melt is a useful solvent and has been used in the electrodeposition of Mo,3Ce,4 and u5 metals. Senderoff and Brenner3 measured the potentials of Zn/Zn++, Fe/Fe++, Cu/Cu+, Mo/Mo+++, and Ag/Ag+ against an Ag/AgCl (pure) reference electrode at 600°C and a concentration of 4.1 mole pct of each chloride and came to the conclusion that complex ion formation occurred in some of the melts. Laitinen and LiUe gave an electromotive force series at 450°C for a number of {Metal/Metal ions (unit activity)) electrodes in LiC1-KC1 eutectic melt, the {pt/pt++ (unit activity)) electrode being chosen as the reference. Walker and Danly7 studied the ther-modynamic properties of NiC12 in LiC1-KC1 eutectic melt over a wide range of temperatures and concentrations by measuring the electrode potential between a nickel electrode and a chlorine electrode in the melt. Since potential measurements made by using the chlorine reference electrode are of more direct significance both in the study of electrochemical separation and in the evaluation of the thermodynamic properties of the melt, it is therefore decided to measure the electrode potentials of cells of the type {M/MCin (mole fraction = N) in LiC1-KC1 eutectic melt/Cl2 over a range of N values and temperature for a number of metal chlorides. The results should indicate the order by which the various metals plate out on the cathode and how this order is affected by temperature and the concentration of the metal chloride in the solu-

Jan 1, 1960

By J. W. Stewart

That our American civilization will have extensive postwar problems in such fields as economics, unemployment, and social adjustment is now well understood by all readers of the press and listeners to the radio. But precious little is heard from these sources regarding the impact of the war on education, though education is one of the fields where the effect of the war is going to be felt most-for youth is fighting the war. Unquestionably, serious educational problems will ;rise in the postwar period, challenging the best efforts of our educators. Most acute will be the problems at the college level of education, for it is this age group that will have had its educational process most thoroughly disrupted. The return of these students to our college and university campuses wiI1 bring about a new set of conditions which we might as well try to foresee and begin to prepare for now. To begin with, the average returning college student who has had his education interrupted by war service will certainly be more mature in both years and mental outlook, and possibly married. As a result he will want to finish his college education as quickly as possible. His natural action will be to shop around among the various schools of the country to see where he can get the most credit for work he has done or thinks he has done. It is just possible that what might impolitely be termed "dark - market" schools may arise to cater to his needs. These schools will not think of them- selves in this light, of course, but will be conscious only of a keen sympathy for the veteran student and an urgent desire to help him solve his pressing problems. A considerable number of American colleges are going to be pretty well impoverished before this present war is ended and unless some professional organization takes it upon itself to place this possible situation under supervision and regulation, we may well suffer a serious setback to the

Jan 1, 1944

[ ]

Jan 1, 1938

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute's Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

THE ladle is a small hearth made on a cage of iron bars like a bird-cage, and has a handle so that it can easily be taken from the forge and carried wherever desired. It is a common device and is much used among masters for small castings, but with a large weight you would have difficulty in lifting it by hand even though you were aided by levers and winches. If you should indeed do it, it would be just as if you had lifted the aforesaid hearth by force, and this would be unwise if you could do anything less difficult. A forge is likewise made for this, with a good pair of large bellows that are well covered with cloth. When the small hearth has been made with good clay, baked, and well covered with ashes, it is placed in front of the mouth [of the bellows] and a crown of two or three brick ends is built around it on top of the rim so that the charcoal may be held better and in greater quantity. Then, having lit the fire and heated the ladle and the charcoal, the pieces of material that you wish to melt are gradually put on

Jan 1, 1942

By Chu-Phay Yap

This is the first of a series of theoretical papers on the iron-carbon system. A simple critical analysis of the ordinary constitution diagram of the iron-carbon system yields valuable information regarding the nature of the equilibria in the liquid and solid states. It is shown, for example, that the solute in the melt is Fe3C, but in solid Fe (austenite) the solute is carbon. The thermodynamic laws of the depression in the freezing point of solid solutions have been developed and discussed. Using the usual method of plotting the logarithm value of the concentration of the solvent (in this case, the ratio of concentrations of the solvent in the liquid and solid phases) against 1/T, curves are obtained. A rigorous thermodynamic analysis of these curves has been shown to yield considerable information regarding the internal equilibria of the system, with which the phase rule does not deal altogether. In this way, it is shown again that the solute in the melt is Fe3C, but in the solid rFe the solute is carbon. Various heats of reaction (fusion and transition) and other thermal data have been derived: and discussed with a view to correlating the conflicting experimental data obtained by different investigators of the system.

Jan 1, 1931

By A. E. Bellis

The time effect in reheating certain steels below the critical range is very marked. The increased toughness, shock-resisting power, and machinability of steel subjected to a long, high drawing temperature has been thoroughly demonstrated and is of practical importance, particularly in the manufacture of "smokeless" rifle-barrel steel. The time effect in tempering is most important when a maximum drawing effect is desired, in which case the highest physical properties as well as ease of machining are important considerations. These are the conditions in drilling a rifle barrel. A hole, 0.30 in. in diameter and 24 in. long for the Springfield rifle, and 30 in. long for the Russian military rifle, has to be drilled in the heat-treated material. This barrel-drilling operation is probably the most difficult one in rifle manufacture, and anyone who has been connected with rifle manufacture knows how seriously production is affected when "hard" or non-uniform steel for barrels is encountered. The importance of high physical properties (tensile strength, toughness and resilience) in a rifle barrel is obvious. The physical properties of two different lots of barrel steel are given below. The first lot, No. 1, gave serious trouble in the drilling operation; the second gave no trouble at all.

Jan 2, 1918

The useful minerals can be subdivided into two large groups. One comprises those which are mined because of their chemical composition. They represent the natural resources of certain materials or of energy (coal). The second group is used not because of their chemical composition but because of certain physical properties or combinations of physical properties. A large number of minerals are mined because of their hardness, their electrical and thermal properties, their color or plasticity. There has been increasing recognition of the value of mineral synthesis during the past 30 years. This is illustrated by the development of improved aircraft spark plugs and chemical porcelain about the time of the first World War. During World War II the impact of crystal chemistry upon ceramics became most pronounced. New ceramic bodies were tailor-made, such as those designed with a high dielectric constant and low power loss, for use in high-voltage, high-frequency communication. In the field of refractories special materials were needed for unusual heat-resisting service in jet and rocket engines, and in the processing of fissionable materials. The synthesis of natural minerals in the laboratory has long been of aid to geologists and mineralogists in their study of the origin of minerals and physico-chemical conditions under which certain minerals were

Jan 1, 1950

By George Beavers

FLASH roasting of iron concentrate is in the experimental stage at Copperhill. The problem is peculiar in that the iron concentrate is predominantly pyrrhotite; the ratio of that mineral to pyrite being 5 to 1. Results so far indicate that the heat, generated in roasting a material containing 52.0 per cent iron and 38.0 per cent sulfur, requires special handling and for this reason the installation costs per ton of roaster feed may be too great to compete with hearth roasting. Interesting features of flash roasting at Copperhill are: 1. The sulfur dioxide content of the roaster exit gas can be varied between wide limits. Eight per cent sulfur dioxide gas, with 1.30 per cent sulfur in the calcine, has been common practice and gas up to 13.0 per cent sulfur dioxide has been possible. 2. Temperatures of the exit gases are very high. When roasting 60 tons or more of iron concentrate per 24 hr. in a modified Wedge roaster, the temperature in the roaster rises to 2000° F. and the calcine is lowered to 0.20 per cent sulfur. If the entire roaster system could be constructed to withstand such temperatures, ideal roasting conditions would obtain as regards sulfur elimination and tonnage roasted.

Jan 1, 1934