Search Documents

By R. J. Murphy, N. J. Grant, J. W. Dowding

A large number of blast furnace slag-metal tests were examined to determine if the manganese reduction could be used as a primary indicator of the degree of oxidation or reduction of the slag and of its desulphurizing power. Slag basicity and temperature were also evaluated. Two laboratory heats were made and sampled prior to reaching equilibrium to check blast furnace data. IN a recent investigation of the factors affecting desulphurization in the blast furnace, is was evident that manganese reduction appeared to parallel the course of desulphurization. Grant, Kalling, and Chipman1 pointed this out in a series of time studies utilizing closely controlled laboratory melts. Fig. 1 is a composite plot of sulphur removal and manganese reduction as a function of time under two slags of different basicity. Manganese reduction appears to approach equilibrium at approximately the same rate as does sulphur. It was also demonstrated that the addition of oxygen to the slag, as manganese oxide, caused a sharp reversal of sulphur from the slag to the metal.' It has been shown that "Excess CaO" was a primary factor in measuring the degree of desulphurization under ideal reducing conditions,1,2 the following reaction being representative of the process: CaO (slag) + S + C (solid) = CaS(slag) + CO (gas) It was also evident that a second reaction could drive the sulphur from the slag into the metal. A suggested reaction was' CaS (slag) + 0 = CaO (slag) + S Any change in the oxidizing power of the system would thus affect both the sulphur and the manganese without causing any change in the calculated basicity of the slag. "Excess CaO," "Excess Base," and other similar basicity values, under such oxidizing conditions, would therefore not be the best measure of desulphurizing power; instead, as was shown by and Chipman" he oxygen content of the slag at low oxygen levels would be the controlling factor. Unfortunately, the extent to which FeO is reduced in the blast furnace makes it difficult to utilize slag FeO as an accurate indicator of the degree of oxidation. By comparison, manganese reduction in the blast furnace proceeds more slowly and is generally only about 40 to 70 pct complete. manganese, which is present in significant amounts and is readily analyzed, offers an opportun-

Jan 1, 1954

By Ellen H. Richards

It is of importance to analysts to have a ready means of detecting the presence of small quantities of titaninm in iron ores and in certain fluxes and slags. The method given in Elderhorst's Blowpipe Analysis (fusion with potassium hydrogen sulphate) requires considerable practice, in order so to regulate the heat that the titanium oxide shall become soluble. In Brash's Determinative Mineralogy is found a method which, at least in inexperienced hands, has given better results, i. e., fusion of the substance to be tested with sodium carbonate on charcoal in the reducing flame. The solution in hydrochloric acid of the bead thus obtained, boiled with tin or zinc, gives the characteristic violet color; but when the mineral contains less than four per cent. of titanium oxide, long boiling and consequent concentration is necessary. In fact the test would seem to be much less delicate than is generally supposed. In the course of some analyses I quite accidentally found that a peculiar color is given to turmeric paper by solutions of titanium chloride. This color is hard to describe, being modified by the quantity of ferric chloride present in the solution ; but it is neither the orange of zirconia nor the red of' boron. It is rather a dull shade of purple, arid is easily recognized when the paper is dried, although the color fades in a few hours. By this means a solution containing .015 per cent. of titanium oxide can easily be tested. The same solution, treated with tin, required to be concentrated to one-tenth its bulk before a decided color could be obtained. The color given to turmeric paper is intensified after the solution has been treated with tin. This and some other indications show that the best shade of color is given by the titanons chloride rather than by the titanic chloride, and no other salt of titanium than the chloride has been found to give the color. Another peculiar property of titanium salts has come tinder my observation. When titaniferous minerals are soluble in nitric acid, and the solution is subjected to the action of the battery, the soluble titanium salt is converted into the insoluble oxide and appears on the electrode, in some cases, as a white coating; this

Jan 1, 1883

By R. T. Pepper

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80° to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- ° diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By d&apos, C. Antonio, S. H. Reichman

In the course of our studies of the annealing behavior of vapor-deposited silver films we have determined the electrical resistivity as a function of annealing temperature for films in the thickness range of 630 to 3240A. Fig. 1 shows the resistivity of the silver films vs film thickness in as-deposited and annealed conditions. The films were prepared by depositing 99.999 pct pure silver from molybdenum boats onto Vycor substrates. Deposition was conducted at a residual pressure of 5 x 10"6 Torr at rates of 20 to 408, sec-'. Thicknesses were determined using a multiple-beam interferometer. During annealing, resistance was measured using the four-probe method. Measurements were made every 5°C during two consecutive anneals to 300°C under a continuous vacuum of 2 x X6 Torr. The heating and cooling rates during annealing were approximately l° and 2°C min-', respectively. Typical resistivity vs temperature curves are shown in Figs. 2 through 4. There is an inflection point evident at 120°C on Fig. 2, the first anneal of a 3240A film. This inflection point was found on all films above approximately 1!00A on both first and second anneals. Below 1400A the inflection occurred at approximately 180°C. Figs; 3 and 4 show the first and second anneals of a 1370A film. The inflection point occurs at 180°C on the first anneal and approximately 120°C on the second. Our interpretation of this phenomenon is based on oxygen liberation from the film surface. It is well-documented that the presence of oxygen on silver surfaces causes a reversible increase in resistivity.1"3 The liberation of this oxygen, for example during vacuum annealing, would therefore cause a decrease in resistivity as observed on Figs. 2, 3, and 4 as a change in slope. This is accounted for by the decomposition of Ag20 on the film surface. The free energy of AgzO becomes positive between 125" and 225°C.4 The thickness dependence of the inflection points can be explained as an orientation effect. The films used in this study were preferentially oriented with their (111) planes parallel to the Substrate.''~ In addition it has been sten that the thinner films, below approximately 1500A, possess a decided "hill and valley"

Jan 1, 1969

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

By Richard Henry Lee

Since the economies in the blast furnace resulting from enriching iron ores are so great, much attention has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods of agglomeration and sintering, of more or less value, have been put into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the gubstance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the ides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 1, 1914

By N. E. Maccallum

Almost half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: aWhat is the safe and economical limit of the open-hearth furnace ?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Go., of Phœnixville, Pa., and their distinctive and important feature is, that they charge to twice the capacitl of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Jan 1, 1913

Discussion * of the paper of H. M. Chance, presented at the butte meeting, august, 1913, and printed in bulletin No. 79, July, 1913, pp. 1315 to 1341. George H. Ashley,+ Washington, d. C.:-Mr. Chance's long practical experience in reporting on coal lands admirably fits him for a discussion of the value of such lands. On behalf of the government geologists, I wish to express my appreciation of Mr. Chance's friendly, constructive criticism of the government method of valuing coal land in the first part of his paper and, at the same time, to reply to some queries he makes. All admit that coal has no " intrinsic "-monetary value, in the sense that a pound of coal of certain chemical and physical characters is worth " intrinsically " so many cents or fractions of a cent. The term has, however, been found very useful as including those natural factors of coal value, among which are its position and location in the earth, that affect its sale price in contrast with the other cost elements involved in the labor and capital necessary in mining, preparing, transporting, and selling the coal (extrinsic factors). Mr. Chance, while recognizing the " dual origin of value," does not offer any better terms. The survey agrees with Mr. Chance in his definition of coal conservation, that it means the fuller utilization of the heat contents of the coal, and the more complete recovery of the coal from the ground. Coal land withdrawals have not been made to keep such lands off the market, but to prevent their acquisition as non-coal lands before they could be classified so as to be disposed of under the proper law. Nor has the pricing of the more valuable coal lands above the minimum been to raise money for the reclamation fund, to which the money goes, but primarily to discourage the alienation, for holding or speculation, of coal lands not intended or needed for development, and, secondarily, to secure to the people the ?unearned increment," which they are certain in any case to be charged.

Jan 11, 1913

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By A. H. Kline, E. B. Zimmer, Zay Jeffries

It is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a finegrained steel rail might have grains or cells 100 times larger than coarsegrained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable khan the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of metal for a specific use, the latter determination being more indicative of the life of the metal part than the tensile test. A grain-size determination with a tensile stest is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now. Several Methods of Measuring Grain Size One of the chief reasons why more grain-size measurements have not been made is the excessive work involved in making a determination.

Jan 1, 1916

By W. F. Holbrook

IN a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 pen cent MgO slags over the range 1475° to 1525° C is included The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple Twelve-gram charges of 0 8 per cent sulphur-metal and 5-gram charge-, of slag were subjected to heating for 30 nun at a prescribed temperature The charges were analyzed for sulphur content For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal Six slag and metal charges were made coincidentally in 5/8-in holes in a section of an electrode graphite rod One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO SLAGS WITH MAGNESIUM OXIDE CONSTANT 15 Per cent MgO -The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SI02, 5 to 27 per cent A1203 and 24 to 53 per cent CaO Variation in composition has been in steps of 2 per cent over much of the area Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered m steps of 4I per cent and even

Jan 1, 1938

By R. A. Spurling, C. G. Rhodes

SATISFACTORY metallographic sample preparation of very soft metals, such as lead and its alloys is generally difficult. The prime requisite of any technique must be that the result gives an undis-torted microstructure for the microscopist to examine. A small amount of mechanical polishing followed by a chemical or electrolytic polish is usually the most desirable way to obtain an undis-torted surface. Several chemical-4 and electrolytic3-&apos; polishing solutions have been developed for dilute lead alloys. Perchloric acid mixtures (with acetic anhydride, ethyl alcohol, or water) are among the most prominent electropolishing solutions used for lead; however, the presence of bismuth in the alloy precludes the use of any perchloric-containing solution. The other solutions1-7 were found to be unsatisfactory on alloys ranging from 10 to 65 wt pct Bi in lead. With increasing bismuth content, the microstructure shows a lead (terminal solid solution), 0-6 mixture, E (peri-tectically formed hexagonal phase), and E bismuth mixture (eutectic at 56.7 wt pct Bi).9 The metallographic samples were mounted in "Araldite" epoxy (the heat generated during polymerization does not alter the microstructure), ground by hand on well-waxed silicon carbide papers (400 and 600 grit), and polished with 3- and 0.25-CL diamond paste on billiard and microcloths, respectively. The use of the various polishing and etching solutions reported in the literature resulted in the formation of irremovable reaction products on the sample surface when applied to "as-ground" or "as-polished" surfaces. The E phase was the most difficult to clean chemically and in the development of an etchant for this system several solutions which satisfactorily etched the bismuth or a phase were unacceptable because of their reaction with the E. It was found that a mixture of 50 ml lactic acid 30 ml nitric acid 20 ml (30 pct) hydrogen peroxide (Solution #1) was a satisfactory etchant for the a-matrix alloys. The samples were prepared as before and etched after 1 min of polishing with 3-p diamond paste. The etchant was applied by swabbing (light pressure) for 30 sec to 1 min and the sample was then rinsed in running water. The E has a slight stain and the a is fairly bright, Fig. 1.

Jan 1, 1965

By F. W. Sperr

The byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.).............................. 69 per cent. of coal Domestic coke (1/2 to 3/4 in.)................................ 2 per cent. of coal Breeze (under 1/2 in.)...................................... 4 per cent. of coal Surplus gas, cubic feet per net ton........................... 6600 Gas for heating ovens, cubic feet per net tor i................. 4400 Tar, gallons per net ton.................................... 9 Ammonium sulfate, pounds per net ton....................... 25 Benzols, gallolls per net ton................................. 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke," (&apos;beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writeri stated that in brass-foundry practice, Connellsville coke is considered rnuch superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in making general statements like these. The percentage of sulfur in coke depends largely on that in the original coal, and byproduct coke from a

Jan 1, 1921

By Frederick W. Bacorn

The paper of Reno H. Sales on Ore Deposits at Butte, Mont.,&apos; is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales&apos;s idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept. But Mr. Sales, for what seem to me to be insufficient reasons, has assumed that there is one deep central source of copper, relatively rich and small, from which all the solutions emanated. From this central source the solutions rose, through one channel or through a group of channels, to the surface, at and within a small area called the central copper zone,

Jan 1, 1915

By D. H. Newland

Certain observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U. S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.&apos; The deposits of Canada are described by L. H. Cole. Several states, including Kansas, Oklahoma, Iowa, Michigan,and New York, have made special surveys of their gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago. Association of Gypsum and Anhydrite The two calcium sulfate compounds, gypsum (CaSO4.2H2O) and anhydrite (CaS04), are the more stable forms of a series which includes at least two other members, so-called half-hydrate (CaSO4.1/2H20) and soluble anhydrite (CaS04). Each of the latter readily takes up water to recrystallize as gypsum and consequently is incapable of existence under ordinary geological conditions; also each can be prepared from gypsum by the application of heat within certain temperatures, the process on which is based the manufacture of commercial plasters. If the temperature limitations are not observed, the result of the calcination process will be insoluble anhydrite which, compared with the soluble form, takes up water very slowly so as to be of no practical use, although actually it is soluble and in time is convertible into gypsum like the other forms.

Jan 1, 1922

By Clarence W. Balke

SMALL buttons of fused tantalum have been produced by arc fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author&apos;s experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author&apos;s opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By P. D. I. Honeyman

CHANGING trends in concentration, involving regrinding with the subsequent production of a finely divided, high-grade flotation product, presents a real problem to the modern copper smelter. In the treatment of such a material, handling difficulties are numerous and potential possible losses may be very great. In many plants, of course, preliminary roasting of the furnace charge remains an economical necessity. Under such circumstances, the operator has no alternative except to follow orthodox roaster reverberatory practice, though taking all possible precautions to avoid excessive dust losses and bad working conditions. In other plants, roasting is not only unnecessary but would be highly undesirable, and at best the charge would be merely dried before entering the reverberatory furnace. In the latter case the possibilities of raw charging loom large. The Miami plant of the International Smelting Co. handles the entire output of concentrates of the several mining companies operating in the Globe-Miami district. All of these companies produce a flotation concentrate which, at the Miami Copper Co. particularly, is all reground and is high in grade. In addition, the Inspiration Copper Co. ships a substantial tonnage of high-grade cement copper to the smelter from its leaching plant. Following the flow sheet of the original plant, all such material received was bedded, dried in Wedge furnaces and smelted in reverberatory furnaces. At times during the history of the plant it has been necessary to carry the drying operation further, to a partial roast, before reverberatory smelting. Since the charge contained over 80 per cent flotation concentrates, the handling of which in a dried condition was at best a dusty job, unusual precautions were taken to cut down dust losses. The Wedge furnace plant was equipped with a Cottrell treater and all hoppers and calcine cars were carefully designed to cut down dust loss in transferring the so-called calcine from hoppers to car and from car to furnace. In the furnace itself the dusting problem was a severe one. Arch erosion was very rapid and flues and waste-heat boilers rapidly filled up with a partly smelted flue dust.

Jan 1, 1932

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By Otto H. Henry

The purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. Review of the Literature The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(1)† In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the position of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermocouple; and (2) that at temperatures above 400" C. the lithium united with the hydrogen to form lithium hydride, thus contaminating the alloys. By applying the same methods as those used in the lithium-magnesium system, Masing and Tammann determined the equilibrium diagram of the

Jan 1, 1934