Search Documents

By A. J. M. Ross

BACKFILLING of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of open-ings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35° to 40° to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transporta-tion of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars prac-tically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1939

By J. D. Lubahn

The Bauschinger effect, or rounding of the corner of the stress-strain curve upon reloading, represents a temporary apparent softness that is more pronounced at large strains than small and for complete unloading than for partial unloading. Interrupted creep tests on copper exhibit a similar temporary softness (high creep rate) upon reloading. The fact that the strainwise dying-out time of these effects is the same in both tensile and creep tests shows that they are related. Thus, the term Bauschinger effect appears to embrace behavior following partial or complete unloading and reloading in addition to behavior following reversed loading. It is suggested that the term may properly apply also to certain creep behaviors following a small load decrement. INTERRUPTED tensile tests at low temperatures show1 a rounding of the corner of the stress-strain curve for reloading, which indicates a temporarily low deformation resistance. In the absence of recovery, the curve soon rises to the value that would have prevailed if the test had not been interrupted. The rounding of the reloading tensile curve has sometimes been referred to1 as the Bauschinger effect, although the term is more commonly applied to low deformation resistance in compression following tensile prestrain. The unusually broad usage of the term Bauschinger eflect in ref. 1 seems justified by the obvious interconnection of the various behaviors to which it has been applied.' In fact, the following discussion will indicate that still broader usage might be desirable. The Bauschinger effect is common at room temperature but apparently disappears at higher temperatures.2 Interrupted creep tests and tensile tests were made on certified OFHC copper (nongaseous impurities exclusive of silver were 0.004 pct), cold drawn 84 pct to ½ in. diam, and annealed at 600" (about 0.025 mm grains) or 850°C (about 0.2 mm grains). The tests were made in standard creep or tensile machines, using an O.S. Peters microformer-type extensometer or, for the small plastic strains, a special arrangement employing General Electric magnetic gage heads.' Interrupted creep tests at room temperature show3,4 an initial softness after reloading, manifested by an initial creep rate that is higher than that which would have prevailed if the test had not been interrupted. Fig. 1 shows some typical examples. This effect is apparently temporary (as is that in tensile tests): in four of the five tests shown, the log rate vs strain curve becomes parallel to an

Jan 1, 1956

By H. W. Krotzer

ADOPTION on a commercial scale of electrolytic deposition of metals brought with it the problem of providing an acid-proof cell or tank. Where the electrolyte contained only a dilute solution of sul-furic acid, wooden, tanks with lead linings were gen-erally adopted. There were cases, however, where a lead lining was impractical as a result of the presence of nitric acid in the electrolyte or because of the method of handling the current for deposition. purposes. Wherever lead was unsuitable for this work, asphaltic mastic was used in its place. This material, in addi-tion to possessing acid-proof qualities and being an insulator for electrical current, is also cheaper than lead. The only reason that prevented the common adoption of mastic for all work of this type was that it was still an unknown, unproved. material; while lead, although more costly, could be relied on. There are several electrolytic tank-houses equipped with acid-proof mastic linings now in operation. The first large one was the series tank-house of the Balti-more Copper Co., where the mastic used was composed of natural asphalts and a silica aggregate. These lin¬ings are now seventeen years old and still in service. The next large plant was that of the Chile Exploration Co., at Chuquicamata, Chile, ,and it is with this that this article deals. Another plant of more recent date is that of the Nichols. Copper Co., Laurel Hill, L. I., and specifications for the new electrolytic tank-house of the Union Miniere du Haut Katanga call for mastic lining. It is also being tried out on a smaller scale or for experimental purposes by many of the larger metal-lurgical companies. Thus while mastic linings were adopted originally to meet operating conditions that prohibited the use of lead, they are now in a position to compete successfully with the standard lead linings that are in general use. The Chile Exploration Co. plant, with a total area of over a million square feet, giving satisfactory ser-vice under the most adverse climatic and metallurgical conditions can be truly called the pioneer in this work. ,This article will deal with the development of the acid-proof mastic linings in Chuquicamata from the original experiments begun in 1912 up to and including the final successful installation that has now been in service for a number of years.

Jan 4, 1927

By H. H. Alexander

IN the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was, used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in. Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. . In 1900 the number of bags was again increased, making a total of approximately 2,800: The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting. As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 8, 1914

By H. H. Alexander

In the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. In 1900 the number of bags was again increased, making a total of approximately 2,800. The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting, As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 1, 1915

By E. V. Foran

AMONG the many newer disclosures that have accompanied the petroleum industry's progressively deeper exploratory drilling is the increased frequency with which the operators are encountering reservoirs of which the products at the time of discovery exist wholly or predomi-nantly in the gas phase. The popular term "distillate pool" is most often used within the industry when referring to this type of reservoir, and in this paper the term is used in that sense. These pools have been observed in many different surroundings. In some places the entire reservoir is filled with the wet gas containing its water-white condensible products in the gas phase but apparently with no dark oil or other hydrocarbon liquids in the reservoir. The 8200-ft. horizon in the Big Lake field in West Texas is a good example of this type. At other places the wet, or distillate-bearing, gas may form a large gas cap directly overlying and in contact with an extensive reserve of dark oil. Oklahoma City, Kettleman Hills, the 8500-ft. horizon in the Big Lake field, and many others are examples of this type. There are also many places in which the wet distillate-bearing gas fills nearly the entire reservoir space, while the dark oil occupies only a narrow, bandlike zone, which marks the boundary of the reservoir along its lowest productive contour. The heavier components of these deep pool gases are generally water white in color, a large portion of which are condensible in a conventional oil and gas separator, when operated under pressures of the order of 400 to 800 lb. per sq. in. Although the water-white products recovered in the separator sometimes have end points of 650° F. and higher on standard Engler distillation, they occur only in the gas phase in the reservoir. It is entirely possible that even some small amounts of dark colored reservoir components may occur in the gas phase when the temperature is 300° F. and pressures exceed 6000 lb. per sq. in. Close approaches to these conditions have been encountered in the deepest producing wells. The condensible content of the deep reservoir gases of the many pools that have been tested or produced to date shows a wide variation in both condensible content, per 1000 cu. ft. of gas, and physical character.

Jan 1, 1939

By Burton Atkinson, David Johnston

Evaluation of Ellenburger reservoirs in West Texas has been an uncertain matker at best because of the lack of cores and suitable core-analysis method. Large amounts of oil arc produced from sections from which sample cuttings are obtained that contain litile porosity and no oil saturation. It has long been realized that the formation in some areas contained numerous fractures and solulion cavities that probably contained the major part of the oil present but the magnitude of the porous system conltaining oil has been unknown. Diamond coring cquipmene, used in the mining industry lor many years, has been developed for oil-field use to obtain high core recovery in fractured dolomite that is not possible with conventional coring equipment. A 36ft section of the core recovered from a fractured Ellenburger reseivoir waS analyzed by a unique but simple method to obtain the first defmite evaluation of one section of the producing formation. The cores and the method of analysis used are described and the results arc discussed in some detail. Discussion The first successful known analyses of cores recovered from the Ellenburger formation in the Permian Basin area were made on cores recovered with the use of diamond core heads. Conventionul coring methods previously used have had lour core recovery and standard methods of analysis have proved to be inadequate for evaluation of those cores that were recovered. Core Descriplion The Ellenburger formation to be dis cussed was cored using diamond core heads and oil-base drilling fluid. Of the total 103 ft cored to a depth of 8893 ft in the Ellenburger, 99 ft or 96 pct was recovered. The dolomite cores were described as gray to white, crystalline to coarscIy crystalline, with chert and calcite inclusions. Occasional shale partings ? to ¼ in. in width were noted. A small amount of green clay was found in some of the coarsely crystalline material. So intergranular porosity was found by inspection in any of the cores. The core urns highly fractured over most of its length with not more than two continuous feet that failed to contain fractures. The fractures Were nearly vertical and varied in width from those harely visible to as much as one millimeter. Scattered solution voids, or vugs, as large as 3 cm in diameter occurred in association with same •a

Jan 1, 1949

By Ralph H. Sweetser

AT the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rejections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blast furnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By V. I. Purcell, S. C. Sun. R. E. Snow

A study including effects of 7) pH value, 2) fatty acid collector, 3) fuel oil, 4) interfering ion, 5) particle size, and 6) operational variables. Test results indicate feasibility of fatty acid flotation under certain restrictive conditions. FATTY acids have been used as standard collectors for floating the matrix1-8 but not the leached zone phosphate ores. After a series of investigations, Davenport9 and Tarbutton10 concluded that the Florida leached zone ores tested were unamenable to fatty acid flotation and must be upgraded by floating the siliceous gangue with Armac-T as collector. The cationic flotation was estimated11 to cost almost ten times as much as a fatty acid process that would ideally give the same flotation grades and recoveries of phosphates. Mineralization: Extensive deposits of leached zone aluminiferous phosphate occur in Florida."= The ore sample used for this work was obtained from the Virginia-Carolina Chemical Corp., Clear Springs area, Florida. The ore is a potential source of uranium and aluminum as well as phosphorus. Since the uranium and the recoverable aluminum are contained in some of the phosphate minerals, an upgrading of phosphate results in a corresponding enrichment of both uranium and aluminum. The phosphate minerals in the ore are primarily pseudo-wavellite, millisite, and carbonate fluorapatite, with a minor amount of wavellite. Quartz and clay are the common gangue minerals, quartz being predominant. Others present in small amounts are ilmenite, hydrated iron oxides, staurolite, monazite, and zircon. Experimental Procedures: After being dried to less than 1 pct surface moisture the material was dry-ground in a Hardinge conical ball mill to —6 mesh. The ground product was classified into 6/20, 20/200, and —200 mesh size fractions. On the basis of Table I, the coarse and fine size fractions were considered as phosphate concentrates, because of their high phosphorus contents. In contrast, the 20/200 mesh fraction, which was low in phosphorus, was used as the flotation feed. All the flotation tests, unless otherwise stated, were performed in a laboratory Fagergren machine under the following conditions: 1) 400 g of solid feed for each test, 2) 2000 rpm impeller speed, 3) 8.9 pH and 4-min conditioning, and 4) 3-min flotation. The procedure used for the quantitative bubble pick-up tests has been described previously.18

Jan 1, 1958

By Norman D. Fitzgerald

The purpose of this paper is to analyze the behavior of oil securities during the six-year period January 1932 through December 1937. This period was selected because of its varied character. It includes the depths of the depression, the broad and spasmodic recovery, and the recession collapse. The first part of the analysis is devoted to the correlation of a number of economic factors with an index of 13 oil stocks. The second part is a comparison of the different,ial behavior of 6 oil stocks. The relationships developed here are only a few of many that might be considered in a complete analysis. The stock market is regarded as a barometer of business confidence and as such exerts an important influence upon corporate policies, particularly upon industrial expansion. The complex and continuously changing nature of its price structure, the ebb and flow of influences and the effects of impacts require dynamic rather than static analysis. When treated in this way, many of the important fluctuations in market prices and changes in the relationships between securities appear quite logical. The market for oil securities has varied widely in recent years. The Standard Statistics index of 13 oil stocks made a bull market peak of 166.7 in September 1929. The collapse of the boom and the ensuing bear market finally carried the index down to a low of 36.4 in June 1932. From this point oil stocks made an irregular recovery; they reached a top at 139.7 in March 1937, and after maintaining this approximate level through August, declined precipitously to 93.3 in December 1937. The prices of these 13 oil stocks have gone up and down under the influence of numberless variables. These variables are of two kinds, those external to the industry, and those that are solely due to its internal condition. The external factors are political, social, and economic, both domestic and foreign. These are the influences that induce the ebb and flow of all prices in general and security prices in particular. Among the internal factors are the regulation of industry, the development of new reserves and processes, and the disequilibrium due to lack of balance between supply and demand. Some of the simpler relationships are examined in this paper.

Jan 1, 1938

By Douglas J. Robinson

A pilot scale process has been developed to separate mercury, tin, silver, and copper from dental amalgam scrap. Laboratory research led to a process which was operated in 55 gallon drum sized reactors to treat 2000 Tr oz charges of scrap per day. This paper discusses the development work, presents a flowsheet and gives an indication of the equipment necessary to carry out the process on a commercial scale.

Jan 1, 1984

By Alfred Fisher

CONSERVATION of mine timber is becoming in-creasingly important, and the consumer is en-couraged to use treated wood to permit longer life of mine timbers, and attempts are also made to substitute other material for wood. The great diffi-culty in substituting metal and concrete props for wood is the inability of these to give yielding resistance to roof pressure as wood supports do. In Europe, where mine timber costs are somewhat more important than in America, many designs of steel props have been tried, but have been unsuccessful, chiefly on account of inability to give yielding resistances. A metal pit prop that gives the desired effect has been extensively used in European mines and has caused a considerable reduction in accidents from falls of roof. Where mining operations have been sus-pended on account of strikes, conditions were found to be much better where such props were used instead of wood props, and machinery, which would have been destroyed by roof falls had wood props been used, was protected by the use of these yielding metal props. As this prop is adjustable, all the work of adjusting and transferring long props through narrow ways is done away with. It can also be drawn with greater ease and safety than wooden props; when properly used it is practically indestructible. European users have reported savings as against wooden props as high as 80 per cent. It gives audible warning of its working because the sliding action takes place in minute jerks. As the prop yields gradually to pressure its force is taken up by friction between the H sections, and this movement progressively increases the resistance of the prop to the increasing roof pressure. In the early development of the prop, it was designed with two steel members a and b of standard H steel sec-tions of equal dimensions provided with guide claws a' and b', held in frictional contact against each other by two differential wedges, f and g, and a floating link, e. In setting up the prop its two members are drawn out to the required length, the loose wedge, g, is then fitted into the space between the left-hand roller of the link d and the lower member of the prop b, and tapped suf-ficiently tight to prevent any relative movement of the two members from taking place prematurely. The prop is then raised to its intended position and secured in the usual way.

Jan 8, 1927

Discussion of the paper of B. H. Dunshee, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 30, August, 1913, pp. 1511 to 1531. GEORGE E. MOULTHROP, Butte, Mont.:-The recording for the first time by Mr. Dunshee, in a readily usable form, of the various systems of square-set framing applied in the Butte district is a valuable contribution to mining information. The many different methods of framing employed, due to the individual ideas of superintendents and foremen of segregated companies, have given full opportunity to determine the best framing for the conditions as found in these mines, and the final adoption of a system uniform for all the mines has come about through a study of these various methods and an experience covering a period of many years. The sawed 10 by 10 in. and 12 by 12 in. timbers undoubtedly give the best satisfaction; and the style of framing the sawed timber that under all conditions has given the best practical results is that used in the Anaconda group and other mines, described and recommended by Mr. Dunshee. In this framing the posts have a horn 2 in. high and 6 in. square, the cap end having dimensions of 3 by 6 in. Instead of the framed girt shown in the drawings of the Anaconda group, the 6 by 10 in. girt adopted at some other mines, which fits into the cap and post framing with no other preparation than cutting the timber to the necessary length, fills all the necessary requirements for strength and affects a material saving in timber and labor. This, as Mr. Dunshee states, is without doubt the type of framing which would be adopted as a standard for 10 by 10 in. sawed timbers if sawed timber sets were to be used in the future generally. But saw-timber for the mines was becoming scarce and expensive, and round timber for the square sets furnished an alternative which provided, at greatly reduced cost, material which in every way supplied the requirements of the mining conditions. The use of the round timber with a satisfactory framing makes available a conveniently located and large source of supply which up to this time has served no useful industrial purpose. Particularly is this true of small timber, which is still standing in great quantities in the forests where the trees more desirable for commercial purposes have already been cut and marketed.

Jan 11, 1913

By Harvey S. Mudd

AMONG the highly skilled craftsmen of the Renaissance were those who worked with ores and metals. The author of this book, Vannoccio Biringuccio, was a master craftsman in the practices of smelting and of metalworking. Contrary to the customs of a trade, Biringuccio was moved to impart his knowledge to all and thus he has given us the earliest hand- book on metallurgy-in fact, the first printed book dealing with the applied metal arts and the processes of ore reduction. We should remind ourselves that metallurgy is an ancient art and then it fair1y may be said that Biringuccio sought to describe the techniques that had been in course of development since the Bronze Age of western civilization. Whether Biringuccio was a man of learning or a scholar according to the standards of his time we do not know, but today we recognize him as a man of science who gave his wisdom to succeeding generations. It was not until the coming of the Power Age at the end of the eighteenth century that progress was resumed in the science of which he wrote more than two hundred years before. Little is known of Biringuccio's training in his native Siena. It can be surmised that there, as in Florence, where his contemporary Benvenuto Cellini lived, he received his training in the craftsman shops where the industrial arts were taught and flourished alongside the fine arts. Perhaps he and Cellini were acquainted, although there is no mention of Biringuccio in Cellini's autobiography-an omission that Cellini's vast egotism makes understandable. He was the great artist, and Biringuccio was a practical, studious, unromantic figure with no favors to dispense. In the April 1940 issue of Mining and Metallurgy Dr. Smith describes Biringuccio's book under the title of "A Neglected Italian Metallurgical Classic." The article, revised and extended, forms the basis of the introduction to the present volume, and I urge all who take up Pirotechnia to read what Dr. Smith has written in the Introduction. Biringuccio's work is a classic and in its translation Dr. Smith and Dr. Gnudi have brought to bear the high degree of scholarship that it deserves. Dr. Gnudi made the translation at Dr. Smith's request and it was then refined "in the fire" of his scientific knowledge of the subject. The result is a book which the Institute is proud to place before its members and which the Memorial Fund Committee considers it a privilege to publish.

Jan 1, 1942

The Rio Tinto - Cerro Colorado operation was the first major cyanide plant built out of South Africa since the Carlin and Corte mills came on-stream in 1965 and 1969. Its flowsheet was presented in the original monograph, "Gold and Silver Cyanidation Plant Practice, " published in 1975, with a brief description of the plant but without the operating costs. The authors have recently received these data and it was believed worthwhile to present them in this volume along with the aforementioned flowsheet. The Cerro Colorado ore deposit is located at Minas de Rio Tinto in the province of Huelva, Spain, approximately 88 km (55 miles) north- west of Seville. The previously mined copper ore bodies lie on either side of the deposit which is mainly copper ore. The crest of the deposit is a capping of "gossan" containing hematite, limonite, gold, and silver. Separate facilities for primary crushing, concentration of copper ores and cyanidation of gold-silver ores are provided. Fine crushing is common to both ores. The run-of-mine open-pit ore is fed from a stockpile via a surge bin and apron feeder to a jaw crusher. After crushing to minus 150 mm (6 in. ), the ore is washed in a rotary scrubber to remove the clay material ahead of fine crushing. Minus 6 mm (1/4 in. ) screen undersize is pumped directly to the grinding circuit with the screen oversize being crushed to minus 19 mm (3/4 in. ) for feed to the primary ball mill; this is followed by two subsequent stages of ball mill grinding to 80% minus 43 microns (325 mesh). Grinding is with water only; no cyanide is used. After thickening, lime is added to the first two of seven Pachuca tanks for conditioning ahead of cyanide addition in each of the five remaining Pachuca tanks. This flowsheet indicates rapid cyanide consumption and the need to maintain a high strength cyanide solution for silver extraction. Agitation for dissolution of the gold and silver is followed by standard CCD practice employing four 67 m (220 ft) washing thickeners in series, with repulping between each thickener. A departure from American and Canadian practice is the use of Stellar filters developed in South Africa for pregnant solution clarification and recovery of zinc-gold-silver precipitates. The precipitate is treated with acid for zinc removal, the sludge filtered in presses, dried, calcined and smelted to produce dore bullion of 900 fineness containing 12% gold and 78% silver.

Jan 1, 1981

Human engineering was the keynote of the thirty-ninth annual meeting of the American Society of Mechanical Engineers, which was held in New York, December 3-6. This note was sounded by President Charles T. Main in his address at the opening session and was carried through by all the speakers. In his survey of the year's work, he said that more than 6000 names of engineers were furnished the Government for filling a wide variety of positions. In addition to the 1400 members in service, two members of the council of the society are in uniform in France and one, as a distinct war service, is in charge of one of the largest shipyards. After giving other ways in which the Society has helped the Government, President Main called attention to the necessity for thoroughgoing efforts to increase production and the settlement of questions involving industrial relationships. At the following meeting, President Adams of the American Institute of Electrical Engineers called attention to the necessity of meeting labor in a progressive way, facing labor questions fairly and squarely, as the real interests of labor cannot be separated from those of the engineer. Charles E. Knoeppel, discussing "Industrial Organization as It Affects Executives and Workers," said the problem of the cost of living might be settled in two ways: 1, there must be more producers, and 2, there must be a greater amount supplied by those now producing. The first solution is practicable, he said, if labor is allowed shorter hours, better conditions, and a remuneration that will attract workers. The second can be employed by eliminating waste, standardizing conditions, setting fair tasks, and allowing men to earn an amount that will compensate them for' their skill and cooperation. Dudley R. Kennedy of Philadelphia, employment manager of the American International Shipbuilding Corporation, said the human-engineering phase of the country's industrial development had generally been overlooked. "We hardly yet know what competition means; we will learn it within a few years. Permit me to prophesy that the executive of the next decade will be the man who best knows men. He will be an originator, a handler of men as individuals, a handler of men in the mass, a leader not a driver, a very human man. The science of human engineering is here to stay. The study of human characteristics is the most enduring, as well as the most fascinating in the world, and still the most complex."

Jan 1, 1919

ALBERT Ladd Colby, who died suddenly of influenza at Torquay, England, on Apr. 30,1924, was born in New York City, on June 26,1860. He was educated in the public schools of New York, at the College of the City of New York, and received the degree of Ph. B. from the Columbia School of Mines in 1881. He continued his studies at Columbia, acting occasionally as assistant to Prof. C. F. Chandler, until 1883. For the next three years he was Assistant Professor of Chemistry in Lehigh University; then head chemist and metallurgical engineer of the Bethlehem Steel Co., at Bethlehem, Pa., occupying the latter position until 1903. As head chemist his active and inventive mind devised several improvements in apparatus for increasing the rapidity and accuracy of the analytical work; as metallurgical engineer, he was, from time to time, in charge of the blast-furnace, open-hearth, bessemer, and puddling departments; he had entire charge of the inspection, assignment, and economic use of all metallurgical materials, and he early gave his attention to the formulation of specifications for metallurgical materials—an activity in which he long held a distinguished part in this country, and as a representative of his own country in England and Europe. He also sewed as expert for his company in patent suits, again laying the foundation for valuable service later as a consulting engineer. In this latter capacity he was excelled by few, if any, contemporaries in the iron and steel industry. His mind was ingenious, thorough, clear, and keen, both in the preparation of evidence and its presentation to the Court. He very quickly appraised the value of evidence, or of an answer to a question, and knew how to secure the infermation, either from the available literature of any language, or by special researches or plant studies. In the executive control of literary research for patent purposes, his long training, infinite capacity for digging through long series of articles in English, German or French, and clear formulation of the vital subject matter for the guidance of assistants, made him invaluable. He was also an adept in collecting information on special branches of his profession. For example, when the science of metallography began to assume importance, he made the first really comprehensive bibliography covering the literature of all siderurgical countries; for the newly formed International Nickel Co. he gathered all the information extant on the subject of nickel steel, both in the literature and in the minds of experts in America and Europe. Two books testify to the thoroughness of his work in this capacity, vie.: "American Standard Specifications for Steel,"

Jan 1, 1924

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By Benjamin N. Webber

Many of the auriferous placers of the arid Southwest differ widely from the standard types of stream and eluvial deposits of more humid regions, although exhibiting some of the features of each. This divergence in characteristics is of geological and economic importance and appears sufficient to warrant the consideration of these placers as a class distinct from both stream and eluvial deposits. It is hoped that the consideration of these auriferous gravels as a distinct type of deposit will facilitate recognition of morphological and economic features that might remain obscure if these deposits were viewed in the light of stream or eluvial placers whose type locality is a more humid environment. "Bajada placer" is proposed as the designation for this type of placer deposit. Bajada is the Spanish term for slope and is used locally in the Southwest to indicate the lower slope of a mountain range, the portion consisting of rock debris and standing at a much lower angle than the rock slope of the range proper. It has been used in a geologic sense by Schraderl and others. The type locality of bajada placers is the Sonoran Desert,2 where they occur on the bajada or rock debris slope of desert ranges. Stream placers are represented in the Southwest, but most of them lie within the mountain topographic province, the Mexican Highlands2 section of the Basin and Range physiographic province. Eluvial placers may occur in the mountainous semiarid Mexican Highlands but are almost unknown in the extremely arid Sonoran Desert, as mountain slopes are generally too steep to permit the accumulation of any considerable mantle of residual debris. Since their salient distinctions are almost wholly the result of formation under conditions of extreme aridity, bajada placers are largely confined to the Sonoran Desert, although a few occur in the adjacent Mexican Highlands. They may be modified by the action of ephemeral streams, in which case the placer gravels of these arroyos approach stream placers in type and habit of occurrence, but their relation to an arid environment and the bajada type is usually apparent.

Jan 1, 1935