Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

EXPERIENCE has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. TEST MATERIALS Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It was found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended on the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as one eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from. 900°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal composition was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical properties and certain bearing properties of this alloy are described in the present paper. PREPARATION OF COMPACTS Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition: 25 per cent nickel; 7 silicon; 3 phosphorus; 64 copper. This alloy is brittle in. the cast condition and can be readily powdered. SINTERING PROCEDURE The blended powders were pressed at 25 to 40 tons per sq. in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Harold Margolin, W. R. Hibbard, R. W. Fenn, H. P. Moore

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By E. A. Smith, E. R. Parker

METALLURGISTS and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applications and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. Single-crystal copper specimens were broken in tension at impact velocities up to 100 ft. per sec. The distribution of slip bands in the fractured crystals was found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. EXPERIMENTAL PROCEDURE Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were made into test bars by sliding threaded steel bushings over each end of a crystal and then flowing silver solder between the crystal and the bushing. The inside diameter of the bushings was slightly greater than the diameter of the crystals, to allow space for the silver solder. The bushings were placed so that the gauge length of the crystals was one inch. The assembly is shown in Fig. I, with two views of a fractured crystal. Annealed polycrystalline copper bars of similar shape were machined from solid stock. X-ray measurements were made on all single crystals to determine their orienta¬tions. The results are shown in Fig. 2, where the location of the axis of each specimen is indicated on a standard projection. The bars were broken in a commercial variable-velocity tension im¬pact machine, which has been described in detail elsewhere.7,8 The stress and strain were recorded by means of wire strain gauges and a special commercial oscillo-raph, also described in detail elsewhere.9,10 The equipment and method can be briefly described as follows. The impact machine consists of a motor-driven flywheel containing a two-pronged hammer. This hammer is held retracted in the flywheel

Jan 1, 1944

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Brooks J. Klimley, Daniel M. Higgins, Grover R. Castle

Measuring The Economic Viability Of Resource Projects (A Western Surface Coal Project) The bankers approach to the analysis of a new "green fields" mining project is similar but different from the approach that the pining company might take. The purpose of this paper shall be to discuss the techniques that are used by mining companies and bankers as they try to measure the economic viability of mining projects. The analysis of these new projects (by both the mining companies and the banker) is based on a projected revenue stream and not on historical earnings or past perfomance because these projects are start up situations with no history to look to. The starting point in the analysis of these projections is the choice of the assumptions to be used in preparing these projections. After the assumptions have been determined and the projections are prepared then the projections are submitted to various tests in order to determine whether the project measures up to previously agreed upon minimum standards. In order to illustrate the analytical procedures used in evaluating a mineral project the writer has constructed a hypothetical case involving the development of a western surface coal mine (Property). The basic data in connection with this hypothetical new project is described in the next section of this paper. After the Description of the Project is a section which shows the type of analysis that a mining company might prepare in order to approach a bank for a loan and the final section illustrates the type of analysis that a bank might prepare in evaluating this loan request. Description Of The Project or Basic Data In Connection With Undeveloped Western Surface Coal Property An independent mining/geological Consultant's report has been completed on the Property which confirms that the Property contains 175 million tons of economically recoverable coal subdivided into the following reserve categories in accordance with U.S. Bureau of Mines and U.S. Geological Survey definitions: Measured or Proven 90,000,000 Indicated or Probable 50,000,000 Inferred or Possible 35,000,000 The owners of the reserves have chosen to drill up those reserves that are nearest to the subcrop and have not spent as much time on those portions of the Property which are on the fringes of the deposit where the overburden is thicker because the stripping ratio and hence the operating costs and capital requirements are higher down dip. The proven reserves are based on an average thickness of 80 feet, of which a mining recovery of 90% is projected. The overburden thickness varies from 0' to 280' with an average thickness of 127'. The overburden consists mainly of scoria, sandstone, gravel, shale and silty clay. 134 holes were cored (and analysis done on five foot increments) in the measured reserve on the following spacing: 100 foot centers to define the burn line; 1,320 foot centers to define the early mining areas; 2,640 foot centers to identify the later mining areas.

Jan 1, 1985

By J. B. Clark

An exploratory study of the 60 wt pct Mg and 80 wt pct Mg sections of the solid constitution in the magnesium-rich region of the Mg-Al-Ca-Zn system was undertaken. The objective of the investigation was to determine the general configuration of the phase fields with respect to the magnesium solid solution in this complex system. The 335°C (635°F) tetrahedron was selected for study because the solid constitutions of the bounding ternary systems—Mg-Al-Zn,1 Mg-A1-Ca,2 Mg-Ca-zn3—were well known and, at least in these ternary systems, diffusion was rapid enough at 335°C for equilibrium to be reached fairly rapidly. Metallography and powder X-ray diffraction were selected as the best corroboratory methods for determining the solid phase equilibria. A total of forty-six quaternary alloys on the 60 wt Mg and 80 wt Mg sections were prepared, annealed to equilibrium at 335°C, and the phases present identified. Singly sublimed (99.99 pct) magnesium, electrolytic (99.99 pct) zinc, high-purity (99.99 pct) aluminum, and USP calcium were alloyed in graphite crucibles under a chloride flux and chill cast into a split graphite mold. Alloy samples were sealed under argon in Pyrex vials and annealed at 335°C ± 1/2° for a minimum of 500 hr. At the conclusion of the anneal, the alloy samples were quenched rapidly in ice water. Standard metallographic procedures for magnesium alloys were used. Powder X-ray diffraction patterns were taken on a G. E. Camera with a diameter of 14.32 cm using nickel filtered copper radiation. The phase equilibria in the 60 wt pct Mg section of the 335°C (635°F) tetrahedron is shown in Fig. 1. The complex equilibria in the zinc-rich region were not accurately determined and are shown only tentatively with dotted lines. The equilibria of the three bounding ternary 335°C sections from pure magnesium to 60 wt pct Mg are also shown as though folded away from the tetrahedron. The 80 wt pct Mg section has the same configuration of phase fields as that shown in Fig. 1. Thus it is reasonable to conclude that in higher magnesium sections, the same relative configuration of phase fields is maintained though the relative proportions of the individual phase fields may change slightly as the magnesium solid solution is approached. Note that all the ternary phases present in these ternary diagrams enter into the quaternary equilibria with the exception of the phase of the Mg-Al-Zn system which becomes unstable with the addition of as little as 1/2 pct Ca. No quaternary intermetallic phases were found. No liquid phase was detected in any of the quaternary alloys annealed at 335°C suggesting that if a quaternary eu-tectic exists, it must lie between 335°C and 339°C, the temperature of the ternary eutectic in the Mg-Al-Zn system.

Jan 1, 1962

By Alfred Brooks

THE only oil produced in Alaska in 1923 was obtained from a dozen small wells, one of which was drilled during the year on the single patented tract of petroleum land in Alaska, in the Katalla field. These wells are owned by the Chilkat Oil Co., which finds a ready local market for its product in the form of gasoline produced in its own refinery. The search for oil has been continued, but except in the Cold Bay field there has been no drilling in new fields during the year. Drilling was in progress during 1923 at Pearl Dome, 18 miles from the coast. Here the Associated Oil Co. sank two wells, about 500 and 950 ft. deep, but suspended drilling in June. The Standard Oil Co., drilling on the same structure, reached a depth of 300 ft. by August and is reported to have reached about 700 ft. by November. The company began the, installation of a second drill in August. George C. Martin, who hastily examined the Chignik region, south of the Cold Bay field, reports that what is known of the geology near Chignik is not favorable to the presence of petroleum. Kirtley Mather, who made a geologic survey of the northern part of the Alaska Peninsula, reports that some of the structures and the formations are favorable to the presence of oil. A small seepage has long been known in the region near the mouth of Douglas River, which flows into Cook Inlet. Sidney Paige last summer made an examination .of the oil seepages which have long been known near Cape Simpson, 50 miles southeast of Point Barrow, the northernmost point of Alaska. He reports that there are two very large seepages emanating from small ridges about a mile apart and several miles from the coast. These are marked by flowing petroleum, and cover many acres. There is a very large accumulation of petroleum residue at these seepages. The surface exposures consist of clay shales with hard thin partings of calcareous shale which lie nearly horizontal, and are probably, of Jurassic age. Mr. Paige and his two sub-parties explored a large area inland from the Arctic coast between Cape Beaufort on the south and Point Barrow and Cape Simpson on the north. He himself ascended the Meade River for 150 miles. These surveys indicate a wide distribution of what is believed to be the formation from which the Cape Simpson seepages emerge, which is probably of Jurassic age. These rocks near the north Arctic coast are little disturbed, but are increasingly folded to the south, toward the mountains. No other seepages have been found, but what is known of the geology is not unfavorable to an oil field. This entire region lies in Naval Petroleum Reserve No. 4, and it was examined by the Geological Survey at the request and expense of the Department of the Navy.

Jan 3, 1924

By R. G. Vardiman, M. R. Achter

THERE has been interest recently in the conditions under which dislocation pipe diffusion may be observed. In order to extend the measurements to temperatures below Tm/2, where pipe diffusion becomes more important, a chemical sectioning technique was developed for silver single crystals which makes possible the removal of layers of 100A or less. The procedure is briefly as follows. Silver single crystals of 99.995 pct purity were cut in the form of discs t by 4 in., electropolished, and electropolated with Ag110 to about 1000A thickness. The thickness was determined by calibrating the activity with the weight of heavier platings, up to 10,000A. Both diffused and undiffused samples were sectioned in a two-step process. Reaction with a solution of iodine in alcohol formed a thin, even layer of AgI, which was then dissolved in a KCN solution. The reaction rate of the iodine solution varied slightly over a period of time, so that the thickness of the stripped layers, while quite even and regular for a given specimen, ranged from 65 to l00W for different specimens. This variation was checked by using a thickly plated standard with each run. Layer thickness was determined from undiffused samples by the point where the layer activity drops to half the maximum. This maximum intensity also provides, with appropriate corrections, the initial concentration per layer co. Because of the small penetration distances, it is necessary to use the exact solution of Fick's law for a source of finite thickness.' For a plating of thick- where c is the concentration at depth x. flj the error function, D the apparent diffusion coefficient, and t the time. The diffusion coefficient was obtained from the concentration-penetration data by extrapolating to x = 0 where c/co = erf h/2(Dt)1/2 Enough points were taken to impart confidence in the accuracy of the intersection, generally about ten layers. Four temperatures were used as in Table I. For best accuracy, t and h were chosen to give values of the parameter (Dt)1/2/h between 1.0 and 1.7. A typical concentration-penetration curve is shown in Fig. 1. The diffusion coefficients calculated from Eq. [I] are plotted in Fig. 2. For comparison, the high-temperature data of Tomizuka and sonder 2 which go down to 630°C are plotted as the solid line 2(a) from their expression D = 0.40 exp (-44,090/RT). Also for comparison, the lowest temperature point of Hoffman and Tumbull3 is plotted. It is apparent that our data diverge appreciably from the high-temperature extrapolation by 373°C. A better straight line fit for the low-temperature portion is obtained by subtracting the extrapolated volume diffusion coefficient from the apparent. or measured coefficient, and plotting the difference, curve (h) of

Jan 1, 1970

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

THERE has been a lot of talk about the shortage of engineers and we have done our share of it; but recently we heard a spot radio commercial-between broadcasts-urging high school seniors to study engineering. We think this is going too far. Engineering is an exacting profession requiring the highest personal qualifications. Publicity for the purpose of interesting capable young people in choosing courses in engineering should emphasize qualification. The opportunities for a career in a great constructive profession which is the basis of our high standard of living should be properly evaluated. Although there is a need for more engineers today, nobody knows what the employment potential is going to be four years hence. The profession may do itself a grave disservice by attempting mass recruitment in the face of an unpredictable national economy. The mining and metals industries are in a special position as fewer engineers are needed in these fields. Only 10 pct of all engineers are mining and metallurgical engineers. Today's shortage is not so much in recent graduates, but in trained practicing engineers. The shortage has served the profession to good effect because it directed the talents of engineers into more productive channels. In some areas high school graduates have been put into routine jobs such as, surveying. If there is one thing the mining profession does not want, it is an oversupply of graduates which would relegate college men to years of work and discouragement in routine jobs. The public has a clear cut picture of the legal and medical professions and thus the respect knowledge imparts. But the engineer is variously thought of as a man who pulls the throttle lever on a locomotive, tends a furnace, or builds a bridge. The term engineer is too loosely used. For instance we have heard of "crowd engineers" and "exterminating engineers." In some unions an engineer designation has been established to describe a person doing routine checking or other control job. We do not disparage these positions but they are different from the work done by the man qualified by years of experience and study. Many of these so-called engineers are not engineers at all. The engineering profession has cooperated closely on a program of recruiting high school graduates for engineering study. It should start a cooperative public relations program to enlighten the public on the accomplishments and work of engineers. This type of publicity need not be of the bombastic type. It can be educational and dignified. Radio, television, and the periodicals can be used to convey information. It is time that laymen and interested young people learn to make a distinction between the true engineer and the technician. Such a program would instruct parents and high school students and thereby interest the right type of people in the engineering profession. The Centennial of Engineering sponsored by the American Society of Civil Engineers is a step in the direction of instructive public relations. This fine start should not be allowed to remain as a one pass venture. The engineering profession as a whole should follow this exposition with a sustained, well directed effort to inform the public of the engineer's work and the possibilities it holds for a constructive career.

Jan 1, 1952

By Bunting S. Crocker

Bunting S. Crocker (Executive Vice President, Kilborn Engineering Ltd., Toronto, Ont., Canada)-This is an interesting report on laboratory-scale testing with pebble charges in 12-in.-diam mills, and the author correctly concludes that useful laboratory testing can be done. In the opening paragraphs he states, "laboratory pebble-milling tests have been considered too difficult to perform and not relevant enough to the actual grinding situation"!! This is definitely not so! The writer published detailed tests done in a 12-in.-diam mill comparing pebble and steel balls in 1952 6 and again in 1954 7. We note that our review paper in 1963 was the only one mentioned in the References. The author states that "a smooth lining is more frequently used in commercial-scale pebble grinding." The writer has designed some 22 plants treating 134,000 tpd in North America and Australia. He has also visited pebble installations in Norway, Sweden, Finland, and South Africa. All these plants correctly use heavier lifters than would be considered standard for ball mills of a similar size. Smooth liners are not recommended in wet ore treating plants. In the 1952 paper6 it was clearly demonstrated in the test work that the individual ore pebbles had to be the same weight-not the same diameter or size-as the steel balls if comparable grinding results were to be obtained. In the tests performed in this study most of the pebbles "passed 50-mm round hole screen openings and remained on a 40-mm round hole sieve. Correspondingly most of the ball mill experiments were performed with 50 or 40-mm steel balls". Thus, the balls and pebbles were essentially the same size or diameter. This means we are comparing apples and oranges. When the feed being ground is fine enough the pebbles will be superior. When the feed is coarse the steel balls will be the better. This is similar to grinding tests in which two sizes of steel balls are compared. In the middle of the article, "Crocker5 has reported that equal weights of pebbles and steel balls achieve the same grinding capacities under similar conditions …", then he proceeds to question this postulate. In the eight reports that I have published, I have never made this statement. What I have said is "for comparable grinding, the individual pebbles in the mill charge should be the same weight as the individual steel balls." This is not the first time that I have been misquoted on this point! It is most unfortunate that this test work has been done with a ball and pebble of the same diameter and not the same weight. It is impossible to properly evaluate the results. I also regret the fact that the screen analyses of the tests were not shown. Many of us who have been 40 years or less in the grinding game can easily read screen analyses at a glance. We can tell whether the top meshes are being ground by the ball charge, etc., etc. The graphs are fine for the summary or to illustrate conclusions but are often misleading in the report itself. However, we do agree that useful pebble grinding tests can be done in a 12-in. mill.

Jan 1, 1973

INTRODUCTION Trade financing is a particularly important component of short-term financing for a minerals company since errors, extra costs, or payment delays/defaults can easily wipe out the profit margin on a particular shipment or can cause problems when arranging purchases of e.g. reagents. It is required to make any minerals operation function and does not have to be cross-border to require proper management. Sources of working capital are as follows: 1. Extended credit terms from suppliers 2. Inventory loans from banks, finance companies 3. Accounts receivable financing or factoring 4. Credit lines or overdraft facilities from banks. TRADE CREDITS These are provided under the familiar terms "net 10 days" or payment due by the "10th day of the following month." Thirty days for payment is usual but longer periods can be negotiated with regular suppliers. Shipment may be made on open account with specified periods for settlement. In the mining industry, a custom smelter gains trade credit by paying for concentrates three months after the month of shipment. INVENTORY LOANS Various forms of inventory finance are provided via "floor-plan" or warehouse financing. A set percentage, usually 60%-80%, of a good-quality, readily saleable inventory item (e.g. bullion, concentrates, ingots) will be provided by a bank or finance company which will usually have security over these products and has a right to inspect the goods from time to time. Legal security will he achieved by warehouse receipts, floating liens, chattel mortgages, trust receipts, or through collateral management service companies. The latter certify control over stock or distribution outlets and often carry insurance against fraud. Costs range around 1.5% - 2.0% p.a. or more plus some fees to cover out-of-pockets or other costs. ACCOUNTS RECEIVABLES Accounts receivable financing is based on the company's generation of satisfactory receivables which are continuously assigned to a bank or finance company ("factoring"). Because of the risks in being able to collect receivables, such as payments to a smelter for its blister copper shipments to a refinery, this form of financing costs as much as 3% - 5% of the debt amount purchased plus an additional charge for processing paperwork. Receivables can be purchased with or without recourse and on a notification or non-notification basis to the client's customer to, respectively, pay the invoice directly to the bank or not. LETTERS OF CREDIT Letters of Credit ("L/C's") are a common feature of international trade finance whereby a bank, at the request of the buyer, issues a written undertaking to an exporter to pay a specified sum of money within a set time on presentation of previously specified documents. This undertaking means that the exporter is no longer relying on the credit standing and integrity of the foreign importer. A dispute about shipment does not otherwise affect the obligation to pay upon presentation of a "clean" set of documents. These documents include the hill of lading and other documentation, often on standard "form" bases. There are a number of conventions and techniques in L/C's such as irrevocable/revocable L/C's, time L/C's, confirmation/advising L/C's and transferable L/C's. These are tools to adjust for the varying risks that the importer will not pay. Other routes where one is comfortable with an importer include documentary sight hills (D/P hill), documentary term bills (D/A bill), and, of course, open account.

Jan 1, 1985

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By T. S. Washburn

THE grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure-killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes are not present. Also, the rimmed ingot has no well defined pipe, as com-pared to the deep pipe on the killed ingots, and there are numerous pri-mary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differ-entiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7-as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined or deep as in the killed ingot of Fig. 1. In killed ingots, pri-mary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

[Aase, Qlenn D., (Junior Member '40) Jr. Met.. American Smelt. & Refin. Co., Selby. Calif. Abadie, Henry G., (Junior Member '43) Petr. Engr.. Avenal, Calif. Abbott, Clarence E., (Member '04) Civil En=.. V.P.. Tennessee Coal. Iron & R.R. Co., 1542 Brown biarx Bldg.. Birminpham, Aln. Abbott. Fred E., Jr., (Member '44) Petr. Engr., C/O Arabian Anierican Oil Co.. A.P.O. 816. c/o Postmaster, New York, N. Y. Abel, Raymond L., (Member '28) Chem. Engr.. C. O., Pittsburgh Chem. Warfare Procurenlent Dist.. American Bank Bldg., Pittsburph. Pa. Abel, Walter D., (Member '32) Min. Engr.. Supvr. Engr.. RFC, Los Angeles, Calif.]

Jan 1, 1946