Search Documents

By J. W. Rutter, K. T. Aust

In previous studies of grain boundary migration in zone-refined lead, the authors used bicrystal specimens consisting of a striated crystal which was grown from the melt, and an adjacent striation-free crystal, introduced by artificial nucleation and growth.1 While this method permits the study of the motion of individual grain boundaries, it does not provide control of the relative orientations of the grains. The present note will describe a technique for controlling the orientations of the two crystals in this type of specimen. The technique consists essentially of placing a striated crystal and a striation-free crystal of controlled orientations end-to-end in a graphite trough, then melting a short zone at the junction of the two crystals and allowing it to freeze to form the desired grain boundary. The apparatus used to carry out this process is illustrated in Fig. 1. It consists of a trough milled from high-purity graphite,with grooves in the underside for the placement of thermocouples. The graphite piece fans out on one end at the level of the bottom of the trough; the sides of the trough are completed in this region by the attachment of a mating plate with a slot cut at any desired angle to permit reorientation of the crystal placed at this end of the assembly. The joint between the crystals is made at or near the point where the slotted plate joins the rest of the trough. The thermocouple slots are deepened in this region so that the thermocouples are separated from the melt by only 1/32 in. of graphite. An induction heater, with suitable temperature control, is used to obtain the molten zone. The two single crystals used are first chemically polished in a solution consisting of eight parts glacial acetic acid and two parts 30 pct hydrogen peroxide. They are then placed in the trough with the ends to be joined at the position of the thermocouples. Next, cooling is applied to the two crystals by means of air

Jan 1, 1962

By M. E. Wadsworth, K. J. Richards

The oxidation rates of tantalum in various partial pressures of carbon dioxide in the temperature range 700°to 950°C were measured with a thermo-gravimetric balance. Oxidation involved a surface -controlled reaction associated with the formation of a nonprotective layer of Ta2O5. Below about 720°C, there was a change in the rate-determining mechanism, and above 830°C the linear rate was preceded by a complex region of nonlinear oxidation behavior. The linear oxidation of tantalum has been explained quantitatively in terms of carbon dioxide adsorption, followed by a rate-controlling surface reaction. The initial adsorption has been expressed both as an equilibrium process and as a steady-state reaction. The enthalpy for chemisorption of CO, was determined to be -17.3 kcal per mole. The surface-controlled reaction had an activation enthalpy of 40.4 kcal per mole. A considerable amount of interest has been shown in recent years in the oxidation of tantalum and the nature of the oxide film produced. This interest is associated with the increasing demand in our technology for structural materials to withstand high temperatures and corrosive atmospheres. The low oxidation resistance of tantalum has severely restricted its application as a high-strength, high-temperature material. As a fundamental approach to the realization of the full poten- tials of this metal, the kinetics of the oxidation of tantalum in oxygen and air have been extensively studied; however, very little work has been reported on the effect of other gases, including carbon dioxide. According to Miller,' the only reported study of the reaction between tantalum and dry carbon dioxide is a restricted observation by O'Driscoll et al.2 at 8 atm absolute pressure and 500°C. Therefore, this study was made to investigate the reaction of tantalum with carbon dioxide. EXPERIMENTAL MATERIALS AND METHODS The vacuum-annealed tantalum used in this study was obtained from Fansteel Metallurgical Corp. as 0.025-mm-thick sheet stock. This material had less than 0.1 pct total impurities, and the maximum individual impurity concentrations were

Jan 1, 1964

By H. M. Chance

By courtesy of the officials of the Chicago, Burlington and Quincy railroad, I am permitted to publish the results of an examination made in 1887 and 1888 of' the country west of the Black Hills, and lying between the Black Hills and the foot-hills of the Big Horn Mountains in the northeastern part of Wyoming. With the exception of the country constituting the foot-hills, or the encircling ridge or rim of the Black Hills proper, all of this area is occupied by rocks of Cretaceous age. In the central part of the Black Hills are found the tin-bearing granites, the mica-schists, and gold-bearing slates, already so well known. Surrounding this central area of older rocks (which should be considered as the "Hills" proper) are the attenuated representatives of the Palzeozoic, dipping gently away from the Hills in every direction, overlaid by the gypsum-bearing Mesozoic, which here forms a bold high ridge or rim, completely encircling the Black Hills, and known as the inner ridge. Overlying, and apparently conformable to this, we find the Dakota sandstone, which likewise forms a prominent ridge or rim, known as the first or outer ridge. This is the formation which contains the coal now worked at the mines near Newcastle. It is also the formation in which the best oil-wells have been obtained in the "Stoakdale," or "Beaver," and the " Belle Fourche " oil-districts. Overlying it are the Colorado shales, forming the great plains drained by Beaver creek and the south fork of the Cheyenne river, and extending west to the Belle Fourche, near Donkey creek, where the overlying Fox Hill formation (thin) and the Laramie group, the great lignite-formation, are first seen. The Laramie group occupies the surface from the Belle Fourche at Donkey creek west to the foothills of the Big Horn mountains at Buffalo, an air-line distance of some seventy or eighty miles.

Jan 1, 1891

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Samuel Frantz

THE purpose of this paper is to relate briefly the development of magnetic separation and its extension from the separation of iron into its present use in the nonmetallic field, to suggest possible future exten-sions of its field of usefulness and its possible cooperation with other separating methods. The engineering design of separating machines, and statistics as to the number of machines in operation, types, their location and production are outside the scope of this paper. Specific data will be given, however, on certain selected applications. A large part of human endeavor consists in separating one thing from another; the good from the bad, the desired from the undesired. In fact, a philosopher might plausibly claim that separating things into categories and choosing between them is the object of thought itself. In dealing with matter, separation is nowhere more inherently necessary to attain our objects than in mining and metallurgy. Both our desire and our ability to make separations are results of the physical differences between things. Gross separations such as removing ore from worthless rock or coal from slate are usually made visually and depend upon form and color, which are physical properties. When the desired and the undesired things are intimately mixed, however, it becomes impractical to select visually even if the individual particles are readily recognizable to the eye, and some automatic way of making the particles separate themselves on the basis of their own inherent differences in physical properties must be resorted to. Some of the physical properties which have been used as a basis of separation are: color, shape, hardness, size, density, elasticity, surface properties (surface tension in contact with liquids, etc.), electrical conductivity, dielectric constant, and magnetic susceptibility. Differences in these properties are used in the following methods of separation: color sorting, sifting, settlement in air and in liquids, floatsink methods, flotation, electrostatic and magnetic separation.

Jan 1, 1932

By M. W. Von Bernewitz

AN important regional meeting of the American Institute of Mining and Metallurgical Engineers was held, at Salt Lake City on Aug. 22 to 26, jointly with the fifth annual meeting of the Western Division of the American Mining Congress. The whole meeting was marked by enthusiasm, keen attention to the subjects under discussion, and many renewals of personal contacts. The trips to the various plants were well attended and the local press paid much attention to the meeting. The A. I. M. E. sessions began Aug. 23, with a non-technical morning session. J. 0. Elton, manager for the International Smelting Co., presided. The purpose of this session was to present in a non-technical manner the relation of flotation to mining, smelting, and the State. Ernest Gayford, metallurgist with the General En-gineering Co. of Salt Lake City, gave the definitions of flotation as suggested by Rickard, the dictionary, Weinig, and Taggart. The active agent in flotation is the air bubble, and the two prime requisites are the formation of bubbles and the creation of selective action of the bubbles for metallic particles instead of for gangue particles. Broadly, all the sulfides are floatable minerals, but the oxides, carbonates, silicates and sulfates are not. As far as Utah is concerned, flotation has been one of the greatest means of conserving its natural re-sources, because it has converted millions of tons of waste rock into pay ore; it is recovering millions of pounds of metal formerly lost in tailings; it has con-verted the zinc from a liability into an asset; and has kept thousands of men at work and distributed millions in dividends for the benefit of the State. As to the future of flotation, Mr. Gayford can con-ceive that the next 5 or 10 years may see as much, if not more, advance than was made in the preceding period. The big problem is dressing oxides, carbonates, silicates, and sulfates, and simplification of the number of reagents, also the separation of different gangue min-erals from one another.

Jan 10, 1927

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By E. H. Phillips, A. F. Keenan

6.2-1. Historical Development. Hammering on hand-held drill steel was the earliest type of percussion drilling. It was not until 1838 that Singer developed a steam-operated drilling machine that lifted a drilling bar and let it drop by gravity. J. J. Couch of Philadelphia patented the first percussion drill in 1849. His machine was a steam drill which literally hurled the drill bar at the rock and retracted it by means of a ratcheted wheel. Later J. W. Fowle added automatic rotation of the steel. In 1871, Simon Ingersoll patented a rock drill mounted on a tripod which permitted drilling holes at any angle, vertical to horizontal. Up to the turn of the century, percussion drills in use were piston-type drills. The drill steel was solid and attached to an extension of the drill piston. Hole cleaning was accomplished by the pumping action of the steel in the hole. Down-holes were drilled wet and cleaned with a blow pipe while up-holes were drilled dry, allowing the cuttings to drop out by gravity. The forerunner of our present hammer drill was the free-piston drill which was first patented in 1884, by Sargent. Because solid drill steel was used, it did not successfully clean down holes. J. G. Leyner solved the problem of applying the hammer drill principle to down-hole and horizontal-hole work in 1897. The key was to pass com- pressed air and water through hollow drill steel to clean the hole. Leyner's work on valves and rotation mechanisms increased the blows per minute of hammer drills from 300 or 400 up to 1800 and more blows per minute and made possible the first lightweight drilling machines. The development of automatic feeds followed. 6.2-2. Percussion Drills. TYPES OF DRILLS. There are two types of percussion drills in use today; the piston drill and the hammer drill. In the

Jan 1, 1968

By Louis L. Stott

It is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halskes reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys. PRopeRties of Beryllium A comprehensive summary of the available data on the properties of beryllium is given in " Gmelius Handbuch der Anorganischen Chemie7." The metal is steel gray in color. A fractured surface exhibits a bright luster, which does not appear to change with long exposure to air, probably because of a thin, transparent protective oxide coating. The specific gravity is approximately 1.8. Although there is no recorded actual determination of Young's modulus of elasticity, it has been estimateds, according to Fessenden's law, to be 30,000 kg. per sq. mm., or about 30 per cent higher than steel. Beryllium appears to have an electrical conductivity approximately 1/12 that of copper. The physical constants as available in the literature are given in Table 1. One of the outstanding properties of beryllium is its great affinity for oxygen, nitrogen, sulfur and carbon. One gram of beryllium takes up 1.774 grams of oxygen and will liberate approximately 15.23 kilogram-calories in the combination. The metal apparently reacts with all known oxides at high temperatures; in fact, beryllium will alloy with thorium and zirconium if melted in crucibles of their oxides. The true physical properties of beryllium are still somewhat in doubt, since very small amounts of impurities appear to cause a large variation

Jan 1, 1936

By D. Harrington

One of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo.; their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies were made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to coöperate. While the coöperation of the mining companies is necessary, the companies are put to practically no expense other than supplying a guide to accompany the investigators underground, the length of time spent

Jan 1, 1922

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By Charles Fulton

This paper describes experiments carried on at the Case School of Applied Science, together with their results. Their success led to the design of the larger furnace herein described, but which has not been built. A PREVIOUS article' by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new.

Jan 10, 1924

By Alden H. Emery, J. J. Forbes

The data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in six coalmining states. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand and transporting it from the working face to the surface. The data thus obtained were considered from two angles; namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be made to discuss the former factor in this paper. ConDitions of Mining The mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. All of the coal mined was bituminous, from beds 30 to 120 in. thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by shortwall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face wets done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal were commonly used, although some roof work was done with jack-hammers and a little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1800 to 3600lb. With few exceptions, coal was won at the face by dry methods, that is to say, no water was employed for wetting down the dust either during undercutting, loading or transportation. Observations of Sources of Dust The common sources of coal dust as observed, arranged by decreasing amounts, were as follows: (1) Undercutting with mining machines; (2)

Jan 1, 1927

By H. F. Johnson, C. S. Harloff

The Nichols series system of electrolytic copper refining has successfully maintained its strong competitive position in the copper-refining industry of today; therefore the improvements made in accomplishing this result are of interest. While additional interest would lie in specific comparisons of results obtained in series operation with those in multiple, we have refrained from such a comparison because it can be fair to both only when they are operating under similar conditions on the same grade of materials. Historical The Nichols Copper Co. started a small refinery at Laurel Hill, using its present system, about 1892. The details of the process in its early stage of development were kept strictly secret, so that no information was published or interchange of ideas permitted with the staffs of other copper refineries, where the multiple system was being developed at the same time. However, the fundamentals of the process and type of cell used today differ very little from their earliest form. All operations including loading and unloading of tanks, and all transportation as well, were carried on by hand. The plant remained in this condition with a gradual expansion taking place until the World War forced such a rapid development that little time or thought could be devoted to modernization or mechanical improvement requiring careful design or detailed planning. Considerable progress was made, however. (1) Large refining furnaces were developed. (2) The old expensive air-lift type of circulation was abandoned in favor of the present system. (3) Operating technique was gradually developed to a high point of efficiency. (4) Tank construction and lining were greatly improved, the first concrete tank being installed in 1915. (This tank is still in operating condition.) (5) A new power plant was constructed. (6) Fuel oil was substituted for lump coal on the refining furnaces. (7) Mechanical casting of the finished product was accomplished. During this entire period the plant was particularly fortunate in receiving only high-grade, clean copper bullion coming principally from the Phelps Dodge mines in Arizona. This, together with the lack of

Jan 1, 1934

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and .that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore' had been uncovered and developed that copper sulphate began to appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

By A. S. Adams

A glance at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon. Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surfacc is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract. Contact Angle and Oil Attraction The contact angle—the angle formed by a fluid-fluid boundary when both are in contact with a solid-—has been indicted several times for complicity in the phenomenon of flotation. This angle is supposed to indirectly measure the surface energy of a solid. Thus if we have two fluids in contact with a solid, we may express the difference between the two fluid-solid tensions as equal to the fluid-fluid tension times the cosine of the angle between the two fluids.4 If the two fluids are in contact with the solid, this is, no doubt, an excellent way of establishing relative surface energies. However, in flotation, we deal with substances which are not wetted by water. What assurance have we, then, that the angle

Jan 1, 1928

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru, for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to. appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

By C. L. Ray, R. E. Baarson, H. B. Treweek

As an example of nonmetallic mineral flotation, the separation of several pegmatite minerals will be discussed in considerable detail, from both the laboratory-testing and plant-operation standpoints. The pegmatites have been chosen to illustrate the practicality of the selective separations of the minerals in a complex nonmetallic ore and, in so doing, to set forth a summation of the flotation art and technology which is applicable in part to the beneficiation of several less complex nonmetallic ores. In addition, a brief summary of descriptions of other nonnietallic mineral flowsheets and separations is included. Some of the industrial minerals now being concentrated by froth flotation methods commercially, or in the laboratory, are listed in Table 1. GENERAL CONSIDERATIONS There are two classes of chemicals that are normally utilized as collectors in froth flotation separations of nonmetallic minerals. These are defined as anionic and cationic and are typified by the fatty acids and amines, respectively. The fatty acids are selective to those minerals that have a high concentration of positive surface charges, such as the various calcium minerals typified by calcite, phosphate rock, and fluorspar. The amines are selective to those minerals with a high concentration of negative surface charges, such as silica sand and silicates. It should be noted, however, that by using various inorganic chemicals, a new or synthetic surface can be placed on specific minerals which produces different characteristics, thereby reversing the flotation reagent required for separation. The polar end of the collector attaches to the mineral surface either by chemical or physical adsorption; the nonpolar unreactive end is oriented away from the mineral surface. The result is a hydrophobic coating at the mineral surface which causes attachment to air bubbles. It is this surface condition that permits the floating of minerals which normally sink in water. In order to utilize these fatty acids and amine derivatives, several conditions .must be fulfilled. Before there can be a selective flotation process,

Jan 1, 1962