Search Documents

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By M. R. Pickus, C. H. Mathewson

The study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centered cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans, who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakaoj4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers16 were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1939

Boundary and general corrosio~z rates for higkpurity alutninum were ~rzeasured irz 16 pct HC1 at sJmllow penetrations (< 25 p). The rates for several high-angle random tilt boundaries, several [001] synzmetrical tilt boundaries, a 54-deg [010] twist, and a 15-deg randorn tw~st boundary were one-fourth to one-third higher than that of the (001) surface used as reference. Boundary attack was slower for 23 and 37-deg [001] tilt boundaries and a 16-deg [010] twist boundary. The corrosion rate for a (111) surface was roughly om-third higher than for (001) and was thus about as high as the corrosion rate of the fastest boundaries. The boundary attack did ?lot appear to parallel the variatiorz of boundavy energy. The signvicance of the anisotropy of corrosion was discussed.

Jan 1, 1966

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low and high backgrounds and low, intermediate, and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1972

By H. P. Schwede, H. G. Doll

This paper describes a method to provide identification of particular depths in a borehole through the use of radioactive markers. The correlation of a marker, placed in the wall of a borehole, with known points of the electrical log and with the casing collars in the cased hole permits accurate positioning of tools with respect to a formation, regardless of absolute depth. Such a process is particularly useful in gun perforation of a casing in a well. Technique and equipment are discussed and illustrated. Examples are given of practical application in the field. Introduction During the past decade the search for petroleum has increased the importance of testing zones at depths in wells which have become progressively deeper. The development of new techniques, such as electrical logging, has permitted the identification of producing formations which consist of comparatively thin strata. When thin beds are to be produced at great depths, the problem of positioning tools accurately to place the well in production becomes acute.l Continuous consideration is being given in the petroleum industry towards the improvement of depth measurements in a borehole. The accuracy in absolute depth measurements, whether made in an open or cased hole, whether determined by a cable or a drill pipe, depends upon a number of factors, such as tension, temperature, and calibration. For example, the effects of tension from the weight of 10,000 ft of drill pipe and the thermal expansion of this length . of pipe, where its average temperature has increased SO"&apos;, will Produce an elongation as much as 8 ft.2 The effects Of such factors can be minimized through the use of care in depth measurements, the application of corrections based on experience, and continuous calibration or checking. The fact that different methods and different tools are used to determine the depths of formations in wells will sometimes give rise to a difference between measurements. It is evident that an important requirement in a well is the ability to locate at will any subsurface point. While absolute depth measurements have ion in recent years, it is reassuring to have other means to verify, for example, that a casing is perforated at a particular place with reference to a zone within a formation. Such a check on measurements may be had by placing a reference marker at a point known with respect to the electrical log of the borehole. That point is usually chosen to be in proximity to the &apos;One to be perforated. Thus, only short in depth measurements are made and any inaccuracy becomes very small and of minor importance&apos; The use of reference markers located at fixed points predetermined in each zone where future operations are contemplated enables the operator to position any tool

Jan 1, 1948

By J. Russ, C. L. Clark

For many years attempts have been made to develop a laboratory test that would serve to indicate the proper temperatures to be used in the various hot-working applications to which metals may be subjected as they are being processed from the cast ingot to the desired finished products. That these attempts have not been very successful is indicated by the fact that most of the temperatures in use today in these operations have been developed over a period of years by trial and error. In other words, the selection of the proper temperatures for the hot-working of metals is generally an art rather than a science. Our knowledge with respect to the behavior of metals at elevated temperatures has been greatly extended during the past several years. While most of the work in this field has been done at proposed operating temperatures of equipment, rather than at processing or fabricating temperatures, one outstanding fact has been developed, which is applicable to the entire high-temperature range; that is, that the rate of deformation to which the metal is subjected is of the same order of importance as the temperature. The failure to properly recognize this fact has greatly retarded the development of a suitable laboratory test for determining hot-working temperatures. Influence of Rate of Deformation on High-temperature Properties It is not the intent of this paper to survey all the work that has been done On the effect of deformation rate On the properties of metals. The importance of this factor, however, was shown by Zay Jeffries&apos; as early as 1919, when he called attention to the existence of the so-called equicohesive temperature and to the effect of certain factors on the location of this temperature&apos; Fig. I is a diagrammatic sketch showing the effect of temperature On the relative strength of the crystals and grain boundaries and the type of fracture that will res depnding On the location of the test, or Or temperature with respect to the equicOhesive temperature. Since the type fracture varies, it also follows that at temperatures below the equicohesive temperature the major deformation occurs in the grains: while at temperatures above, the deformation results either from the movement of the grains with respect to each other or recrystallization of the strained material occurs almost instantaneously, producing new crystals at the fracture. As previously indicated, it is an established fact that the position of this equicohesive temperature for any given metal is dependent On the deformation rate&apos; For example, in 0.15 per cent plain carbon steel the location of this temperature under

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By W. R. Hibbard

The term lineage was first introduced by Buergerl to denote dendritic branches, grown from a crystal nucleus during solidification from the liquid, with imper- fections in alignment of the order of 10 : to 10-4 cm. These imperfections are associated with distortions of the dendrites caused by the subsequent solidification of the inter-dendritic filling and are illustrated in Fig I. Buerger etched zinc single crystals made by the Bridgman3 method to develop this dendritic pattern and show lineage microscopically. Since maximum crystal growth in face-centered cubic metals occurs along the [IT] directions,2 lineage would appear in copper as small deviations of dendritic branches from these directions. Elam4 and others5"8 reported etching effects resulting from coring along the cube face traces of various copper alloy crystals. These traces were used by Samans8 to orient single crystals. Williamson9 noted a "lined structure (in alpha brass single crystals) consisting of an ordered arrangement of etch pits" which were probably traces of {IOO} planes but somewhat uncertain because they were never straight (that is, apparently lineage). Greningerl1 described the distortion and multiplicity of Laue spots in back reflection X ray photograms of copper single crystals showing lineage. The present investigation -includes metal-lographic, X ray, and property studies of lineage in large grain and single crystal specimens of copper. Preparation of Specimens specilnens 10 in. long 35 1/2 in. diam of oxygen-free copper (o.F.H.c.) (99.985 pet) were&apos; melted vertically in graphite crucibles under an atmosphere of commercial nitrogen purified through a gas train including sulfuric acid, potassium chloride, magnesium chiorate, hot copper chips and phosphorus pentoxide. After a temperature of 1200°C had been maintained for 1/2 hr, the furnace was turned off and the specimens cooled at a rate of about 150°c an hour&apos; This method of direct solidification was used by Greningerlo to produce single crystals with marked lineage and in this investigation produced a fair yield of single crystal specimens in

Jan 1, 1949

By J. O. Brittain, E. Lautenschlager

An investigation was conducted on fine grained airon wire to measure the influence of the temperature of deformation on strain aging near room temperature. Specimens were deformed various amounts at 77°, 195°, or 273°K and aged. The strain aging was followed by either internal friction or return of the yield-point measurements. The results show that strain aging occurs in three stages. During the first stage there is small, almost immediate return of the yield point. The solute carbon concentration, as mesured by internal friction, remains constant in stage I but is lower than the concentration in the unstrained condition. In the second stage, the solute concentration decreases while the magnitude of the yield point increases. In the third stage, the solute atoms continue to drain from the solution, the yield point approaches a maximum, and the strain-hardening coefficient and flow curve increase. The kinetics of the strain aging reaction are not the same for the two sets of measurements since the internal friction results lag behind the yield-point measurements. However, the strain-aging kinetics measured at 44° and 64°C showed no effect due to the difference in initial deformation temperature; nor were the strain aging kinetics influenced by low-temperature anneals at 77°, 195°, and 273°K. 1 HE object of this investigation was to measure the effect of initial deformation temperature on the strain aging of a-iron by tensile tests (i.e., return of the yield point) and internal friction methods, to correlate the results of the two measuring methods, and to measure the effect of low-temperature annealing (<273°K) after low-temperature deformation upon strain aging. The experiments were performed on fine-grained a-iron wire containing 0.02 wt pct c.l According to Thomas and Leak,&apos; return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solid solution, while the return of the yield point as a function of the aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,3 during aging the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point on subsequent testing. It has been shown that after low-temperature neutron bombardment, a-iron goes through a stage of recovery at low temperatures which can be attributed to the annealing of iron interstitials&apos; and/or vacancies.4 If, after low-temperature deformation, there is an interaction during a low-temperature anneal between mobile point defects and the solute atoms (i.e., carbon atom interaction with vacancy or iron interstitial), it is possible that some solute atoms will be found at defect sites other than dislocations. Such changes in the sinks for the carbon atoms might be expected to alter the strain-aging kinetics sufficiently to be detected by either inter-

Jan 1, 1962

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.&apos; It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By J. T. Burwell

As is well known, the alloys of iron containing 18 ± per cent chromium, 8 ± per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composi-tion (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff, 1 it was decided to investigate the phenomenon by electron diffraction methods.

Jan 1, 1939

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By Donald W. Scott

THE year just ended was the 50th anniversary of that first flight at Kittyhawk, N. C., in 1903. In this 50-year period the aviation industry made startling developments from flight distances of 120 ft-at snail&apos;s pace-to speeds of over 1300 mph and flights that circle the globe. And 1953 also was the 50th anniversary of the Utah Copper Co., the Father of our mass production porphyry copper ventures. How do developments in the mining industry stack up with the aviation industry? The mineral industry can be as proud of developments over the past 50 years as the aviation industry. Only for the developments of the mineral industry could aviation and other allied industries advance as they have. The year 1953 made its contribution to this progress, with the normal number of process and equipment developments and an abnormally high amount of activity in new plant capacity, particularly copper. Tonnages are on the increase and operating troubles are becoming more and more problems in materials handling and control. We&apos;re approaching molecular dissemination of ores with hydro and pyro methods coming to the front to take over where flotation leaves off.

Jan 2, 1954

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

By G. L. Corrigan, J. R. Coleman

Four factors that largely determine the end product obtained when cement and water are mixed are the chemical compo ition of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the more finely ground a cement, and the greater the surface exposed in proportion to its mass, the more rapid is the hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.1 Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are poorer cementing materials than some of the more finely ground construction cements. On the other hand, often it is necessary to pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concerning the proper fineness range.

Jan 1, 1941

By G. Gutzeit

METAL-ORGANIC INNER COMPLEXES AN inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity. 4,1-13 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime.) It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry,, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals.17 CHELATE-FORMING COMPOUNDS AS COLLECTORS In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxylamine (Cupferron) C6H5NO(=NONH4). Holman19 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-dioximes were generally selective collectors for nickel ores. Taurin NH2(CH2)2SO3H has been proposed for the concentration of oxidized lead ores.19 Diphenylthiocarbazone

Jan 1, 1946

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

By Carlton D. Hulin

THE usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma fades are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacement and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district, The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 per cent may occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible.

Jan 1, 1945

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940