Search Documents

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By F. J. Meringer, C. W. MacGregor

Various investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-l2 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 S =1/A and where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. Preliminary Investigations The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 0.19 per cent; S, 0.118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Effect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By H. l. Burghoff, C. H. Mathewson

THE study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and 30 per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrystallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged. loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300º, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrystalline 70-30 brass. PREVIOUS WORK Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty & Moore.4 Results of the last-named investigation were published while the present work was in progress. Millers examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior, of iron crystals under static tensile loading at room temperature was reported by Gensamer and Mehl7 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of creep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By R. J. Wasilewski

Axial expansion has been determined by X-ray diffraction up to 600° to 760°C in a titanium and four high-oxygen alloys. Expansion data cannot be fitted to the usual quadratic expression and anomalies observed are believed indicative of the changes in the bonding configuration of the valence electrons. Furthermore, there is significant disagreement between data obtained on poly crystalline and single crystal powder specimens. The major disagreement occurs within the temperature range (-470°C) where both mechanical and electrical properties also show markedly anomalous behavior. X. HIS work forms part of an investigation of physical properties of pure titanium and its osolid solutiono alloys with oxygen and nitrogen. In view of the anomalies observed in both the electrical resistivity' and the susceptibility behavior it was decided accurately to determine the thermal expansion behavior of the pure and alloyed a titanium. PREVIOUS WORK The axial expansion coefficients reported for pure titanium are listed below. As can be seen, there is a marked discrepancy between the axial expansion and the experimentally determined coefficients on poly crystal line material. Thus, if we take the most recently reported axial expansivities3,4 we obtain perature interval of 25o to 700°C. The experimental value reported for polycrystalline metal is, however, of the order of 9.7 x 10o6 per OC. EXPERIMENTAL I) Pure Titanium. High purity titanium powder of -325 mesh was used throughout most of this work. The only significant impurities present were the interstitials, oxygen and nitrogen, which analyzed respectively 650 and 80 ppm. The purity of the ma-

Jan 1, 1962

By John D. Wiebmer

Lignite Development in North Dakota is a "shotgun wedding" according to former state senator Robert L. Stroup-the unwilling groom (North Dakota) is being led to the altar by the nation's demand for increased coal production. The state's attorney general, Allen I. Olson, reacts to the situation this way: "We have no specific coal policy. We plan to keep the whole matter down to a dull roar and drag our feet until we see how we fit into the national energy picture." But despite a state administration labeled as "cautiously negative" toward resource development, North Dakota has experienced a twofold increase in annual lignite production within the last two years. And within the next four years, three more mine additions will double the state's output again.

Jan 8, 1977

By J. Mackintosh Bell

In the numerous districts subsidiary to Cobalt, and carrying mineral deposits similar in character to that world-famous mining camp, the most interesting recent developments have occurred in South Lorrain. The district, the center of which lies about 16 miles southeast of Cobalt, was the scene of a rush in 1907 but, in spite of the success of the Wett-lauffer mine, the locality soon lost its popularity, largely on account of the unsavory early history of the Keeley mine. In recent years, following the successful development of this property by the London operators, who acquired it from the liquidator of the original company, and the later conspicuous progress made on the properties of the Mining Corporation contiguous to the Keeley on the north, the district has again come into prominence and, at present, is doing much toward maintaining the gradually declining production of Cobalt itself. Apart from the Mining Corporation of Canada and the Keeley Silver Mines Limited, the principal concerns now operating in South Lorrain are the Lorrain Consolidated, the Trout Lake Mines (operated by English interests associated with the Mining Corporation) and the Canadian Lorrain Silver Mines (operated by the Huronian Belt Co., of London). A number of minor prospects are also active. The Wettlaufer and Currie, on both of which considerable work was done some years ago, are now closed. TOPOGRAPHY AND GENERAL GEOLOGY The topography of the South Lorrain area is rather more rugged than that of the vicinity of Cobalt, but the local relief, relatively speaking, is not great. Numerous lakes and streams lend a certain picturesqueness to a landscape, which is not entirely marred by the absence, from the valleys and hillsides, of the splendid bush that formerly clothed them but which has been swept away by forest fires. The geology of the locality is simple, in a lithological sense, but rather complicated structurally. The oldest rocks are Keewatin greenstones

Jan 1, 1924

By Robert Schorr

PAGE 1. Introduction,........... 82 2. Characteristics of Briquettes,........ 87 3. The Manufacture of Coal- and Coke-Briquettes,.... 89 Binders, Organic and Inorganic,...... 90 Mixing,...........94 Presses, Continuous and Intermittent Action,....95 Cost of Briquettes and Sales-Prices in Various Countries,.. 99 4. The Manufacture of Peat-Briquettes,......101 Solid Peat-Slabs,.........101 Solid, Carbonized Peat-Briquettes,......103 Estimates of Cost of Operating Peat-Briquetting Plants,... 105 5. Manufacture of Mineral-Briquettes for Metallurgical Processes,.. 108 6. Manufacture of Artificial Stone-Masses,......112 7. Bibliography,...........115 Introduction. Briquetting is apparently a very simple operation, yet it has offered so many mechanical and chemical difficulties that it required almost a century to place it on a commercial basis. Since 1860, however, the progress has been steady and satisfactory, and to-day, for most of the European coal companies, the briquette-plant is a very profitable investment. Among the many applications of scientific knowledge to further economy by recovering and utilizing by-products and raw materials, there is possibly none which deserves the attention of Americans to a higher degree than briquetting. The recent miners' strike in Pennsylvania, which resulted in a scarce and irregular supply of coal at a high price, has advanced the possibilities for briquetting, and as a consequence public interest has grown rapidly. While the manufacture of coal-briquettes is not new in the United States, adverse conditions and sometimes lack of

Jan 1, 1905

By J. F. Myers, R. J. Tower

"There is nothing new under the sun." All over the world, mineral-dressing engineers are working at their problems, no two of which are alike. Each encounters equipment and process problems. Many devise simple ways and means of overcoming their difficulties. Many of these problems are quite common in the industry, yet, since no one human being seems capable of thinking of everything, these problems at some plants often are looked upon as necessary evils. The purpose of this symposium is to gather together, from competent engineers, devices and practices that have been useful to them. Most of the ideas contributed are not new, yet there is no plant operator, old timer or youngster, who will not find some idea herein that will give him a suggestion for improving his operation. Space does not permit a complete elaboration on all of the contributions offered. Each item is summarized, but this will be ample for those skilled in the art of mineral dressing. A list of contributors appears at the end of the paper, and the superior number at the end of each item identifies its source. General Equipment A signal light to show that a steel bin, containing relatively line, moist ore, is full, can be made by suspending a copper rod in the bin to a sufficient depth to ensure ample contact with the ore. One wire of a 32-volt circuit should be attached to the rod and one to the side of the bin. Sufficient current will flow to make the signal light burn. A 110-volt circuit could be used, but 32 volts ensures safety.10 Fig I shows a circular bin for crushed ore. It is a concrete structure footed on the ground, using no supporting columns. Tailing from the sink-float was used for aggregate. Cross conveyors for discharging ore are not required, nor is a tripper for filling. Segregation is minimized by drawing from different gates. An exhaust fan on top of the bin eliminates condensation due to temperature of the ore.21 A beam with an adjustable point of suspension near the center permits rigging rolls for removal in a very few minutes. This makes unnecessary the lacing of the cable through the hub bolts on one side, around the shaft on the other, and the trouble of balancing the load.8 The ratchet handle on a Symons crusher may be replaced by a drum with a cable wound on it. When the cable is pulled by a crane or hoist it causes the drum to revolve and thus screws or unscrews the bowl. This reduces handwork and materially shortens the time required for the job.' TO Spread ore feed from an apron feeder over a belt conveyor, place a heavy steel bar about midway between the top

Jan 1, 1949

By David Cole

At the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that time impending. The simplified flow sheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.l The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopy-rite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow ,would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) the very fine sand, and especially the very fine but still granular sulphide particles, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrassment, the increase of capacity required. For reasons that are obvious, this kind of feed preparation for the slime could not be successfully accomplished in any form of pointed boxes or

Jan 1, 1917

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

Jan 8, 1951

By C. E. MacQuigg

In this paper it is impossible to more than touch on many of the commercial alloys of iron, chromium, and carbon, therefore the discussion is confined to the properties of some of the less well-known alloys with upwards of 20-per cent. chromium. The discussion has been based largely on the strictly engineering aspects of the alloys. Chromium has well-defined effects when added to the iron-carbon system. These effects depend on the amount of chromium added and on the composition of the iron-carbon alloy to which the addition is made, i.e. whether low- or high-carbon steel, cast iron, etc. In the case of the low-carbon steels, the chromium addition, when not in excess of several per cent., appears to exert an influence on the properties by its influence on the critical range. In the higher chromium alloys, the physical properties are influenced chiefly by the formation of new complexes, such as iron-chromium solid solutions and, with higher carbon contents, iron-chromium carbides of great hardness. Examination of the published data1 on the critical range phenomena of chromium-bearing steels up to several per cent. chromium indicates an agreement on the following points:

Jan 1, 1923

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

By B. H. Sage, W. N. Lacey

The results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of grave! screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. Introduction Gravel screens have been placed in water and oil wells for a number of yearsl,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. Influence OF Gravel Screens upon Productivity The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1942

By William Hurst

This is a presentation of the diffusivity theory for the calculation of the water drive on an oil reservoir in which the history of reservoir pressure with time are the essential parameters for the determination of the rate and cumulative water encroachment into a field. The main body of the paper is essentially the application of the principles underlined here to actual field data. It consists of the work plots of the radial-flow case, and includes a discussion of an illustrated problem for which the water-drive calculations are treated in conjunction with the volumetric-balance equation. The appendix is a mathematical treatment of the linear, radial, and spherical cases of water influx into a reservoir. Introduction The evaluation of oil reserves and the prediction of pressure behavior with different rates of production are related to the volumetric balance of the fluids entering and leaving the space occupied by the oil and gas originally present in the formation; that is to say, important information can be gleaned from a volumetric study of the oil, gas, and water produced from a formation as it affects the extent of change in volume of oil zone, the gas cap, and the amount of water influx from the adjoining water sands. It is not the purpose of this paper to enter into a discussion of the equation of volumetric balance, in which such pertinent information as subsurface sampling and the measurement of reservoir pressures play a predominant part, as this has been discussed in detail by others.1,2 However, there is an inherent difficulty that has limited the general application of this equation to a study of oil reservoirs; that is, the insufficient knowledge of the analytics for expressing the water drive on a field as a function of reservoir pressure. This to a large degree has been overcome and it is the purpose of this paper to present this theory in such form as to be applicable for reservoir calculations. Water Drive If the amount of oil originally in place and the gas space are known, it is a relatively simple matter to determine, by the volumetric equation, the cumulative water influx into a reservoir from the adjoining water sands. Often, however, the oil reserve as well as water influx must be 'determined, and in order to be able to make this calculation it is essential to assign a mathematical relationship for the varying water term that is compatible with conditions known to exist in the formation and gives an accuracy acceptable for engineering calculations. Various equations have been employed empirically by different investigators in making reservoir studies of water drive. One form used by Schilthuis2 expresses the rate of water influx into a reservoir at any time as proportional to the pressure

Jan 1, 1943

By Eric R. Jette, Earl S. Greiner

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By George A. Colligan, John M. Lo

Electrical resistivity as a function of temperature was investigated in undercooled gallium and under-cooled Ga-In alloy of eutectic compositian to examine structural changes in undercooled melts. A continuous linear extension of the resistivity was determined for 99.999 pct pure gallium when undercooled below the stable Ga(l)-liquid, and the metastable Gafl)-liquid equilibria. In icndercooled Ga-In, a significant continuous negative departure from linear resistivity behavior was observed below the eutectic temperature. All resistivity measurements were made by the four-point probe technique. ThE temperature range for investigations into the physical properties of liquids before freezing has been greatly extended with the undercooling of massive melts of pure metals and alloys. Experimental determinations of thermal and transport properties and diffraction patterns in undercooled systems should throw further light on the structural behavior of liquids. Many measurements showing prefreezing anomalies in viscosity1'5 have been regarded677 as evidence for structural groupings in the liquid state. However, the majority of viscosity results,~)~-~~ conforming to the law 17 =A exp(~/RT), do not support theories of atomic aggregation. For the system Cd-Sb, which exhibits a metastable solid phase, Fisher and Phillipsg reported that, in undercooled alloys, the activation energies for viscous flow below the stable liquidus are much higher than those above it. Similarly, Miller et a1." observed a doubling of the activation energies for electrical conductivity in undercooled Cd-ib alloys. These effects were suggested as indicative of atomic association and clustering in the liquids at lower temperatures. With the recent establishment of metastable phases in pure gallium22 and its alloys,23 attempts were made during this investigation to undercool bulk samples and to determine the temperature dependence of electrical resistivitv. Pure gallium, when undercooled below -17°C at atmospheric pressure, can crystallize to either a stable Ga(1) phase (mp, 29.78"C) or a metastable phase identi-

Jan 1, 1967