Search Documents

By H. J. Wasson

At the close of 1927 Venezuela was producing at the rate of 205,000 bbl, per day, making it the third country in the world in point of present daily production. For the year, the total was close to 64,000,000 bbl., representing an increase of about 70 per cent. over the 37,000,000 bbl. in round numbers produced in 1926. All of the 1927 production canie from fields opened up before the beginning of the year. While no new fields were added to the list of shippers, the past 12 months' wildcatting yielded a fair quota of new discoveries which, in the light of prcsent results, may be considered likely sources of production in due time. Altogether three such promising finds were made Of first importance, at least for the immediate future, is the completion by the Lago Petroleum Corpn. of the San Matins well, 4 miles north of the present edge of the Lagunillas field. Although rated as only a 125. bbl. well, at 3217 ft., it indicates a probable extension of the field over the intervening 4 miles between the two. The two other wildcat discoveries of importance were the Los Manueles well in the District of Colon, which has in all probability opened up a new field about 7 miles north of the present Tarra oprations; and the Honibre Pintado well of the Standard Oil Co. of Venezuela,. in the State of Falcon, which is considered to be a promising clc~vc~lop~ncnt. Neither of these last mentioned two discoveries will apprcciably affect production during 1928, as the Manueles area must await the carrying out of a general plan for the exploitation of the District of Colon, a problem requiring time. The Hombre Pintado area is being tested further, but doubtless several wells will be put down before. anything definite will be done towards making the pipe line. arrangements that rnust necessarily precede the commercial exploitation of the field. The San Matias Well The San Matias well is a highly significant dcvelopment,. It is located along the trend of the La Rosa-Ilagunillas producing formations, and when drilling started, production in the Lagunillas field was 4 miles

Jan 1, 1928

By J. S. FINLAY

OPERATING a "muck stick" never appealed to me. It always seemed a terrible waste of energy to "put rocks in the box" by hand-particularly when my own personal energy was involved. But during the past forty years, there have been periods-more or less extended when I was compelled, against my finer instincts, to muck or quit eating. For about the same length of time, I have devised schemes to make mucking faster and more painless. There was always something mechanically wrong with these designs-too many;" parts to wear out and need replacement, and excessive cost incidental to a complicated mechanism. The idea of a shovel unit comprised of a single, rigid assembly which would roll from a digging to dumping position solved the problem of simplicity and durability. Ingersoll-Rand's utility engine provided a splendid power plant, small enough and powerful enough for the job. In the machine finally developed, known as the Eimco-Finlay loader, roller chains are preferred to gears for power trans-

Jan 1, 1935

By W. H. Gauvin, N. J. Themelis

Jan 1, 1963

By C. L. Prokop

A laboratory investigation has been made of the effects of mud hydraulics upon the formation and erosion of mud filter cakes. The tests were conducted to simulate drilling conditions as nearly as possible. The formation of mud filter cake in a drilling well does not proceed at a uniform and unbroken rate. Instead, the rate of cake accumulation depends upon whether or not the mud is being circulated. If the mud column is quiescent, filter cake formation is a smooth function of the filtration characteristics of the system. If the mud is being circulated filter cake formation depends not only upon the filtration characteristics of the mud but also upon the erosive action of the flowing mud column Filter cakes formed during continuous mud circulation were observed to reach an equilibrium thickness after several hours' circulation. Mud circulation was maintained at a constant volumetric rate throughout each experiment. The fluid velocity at equilibrium cake thickness was dependent upon the thickness of the filter cake. Muds having exceptionally high water loss deposited thick filter cakes in spite of very high eroding velocities. The muds having good filtration characteristics deposited thin filter cakes at equilibrium circulating velocities well within tile range of those in a drilling well. It was observed that filter cakes deposited during stagnant filtration were quite difficult to erode by mud circulation. The - rate of crosion computed from the rate of filtrate accumulation after equilibrium cake thickness had been reached was in reasonable agreement with the rate of erosion obtained by direct observation. Continuous mud circulation usually caused the permeability of the filter cake to decrease with time. INTRODUCTION Many of the difficulties encountered during tile drilling of a well have been attributed to the loss of water from the mud and the attendant deposition of solids upon the walls of the hole. Past experience has shown that a reduction of the filtration rate of the drilling fluid eliminates or greatly reduces these difficulties. Definite filtration requirements, however, are hard to establish for a given set of conditions. This is due. in part, to the fact that the usual filtration test performed upon mud doe? not simulate well conditions as closely as desirable. The filtration characteristics of a mud are customarily determined by means of the standard low-pressure API wall-building tester.' In this instrument a filter cake is deposited upon a horizontal bed under a pressure differential of 100 psi. The rnud is quiescent during the filtration period. In actual practice. mud filtration occurs within a well under quite different conditions. One of the major differences is that mud flows upward across the filter bed as the filter cake forms. This undoubtedly produces a change in the filter cake which cannot be reflected in the results of the API test. The laboratory work described in this paper had as its primary objective a better understanding of the influence of mud circulation upon the thickness and ,characteristics of the filter cakes deposited under conditions similar to those existing in a drilling well. ANALYSIS OF PROBLEM Once a permeable formation is penetrated by the bit, filtrate from the mud flows into the formation. 'he mud solids plaster against the walls of the hole, forming a filter cake. If the mud column is stagnant, that is, if it is not being circulated. the filter cake will increase in thickness until the hole is filled. Prior to the time that the hole is filled, the thickness of filter cake existing at any given time will be a function of the filtration characteristics of the mud, the temperature, and the pressure differential. The effects of these variables have been investigated in the past for both flat bed filtration2'3 and for radial filtration.' When the mud is circulated in a hole in which a filter cake i. being deposited. some of the solids that would ordinarily deposit in the filter cake will be carried away by the eroding action of the mud. This will limit. filter cake thickness. Some work has been done to determine the effect of flow upon the filtration rate in a circulating mud system' but little work has been done upon the factors which determine the filter cake thickness existing in a circulating system. On first sight it would appear that the major factors controlling filter cake formation in a circulating system should be: 1. The rate of deposition of solids from the mud. 2. The erosive force that the flowing mud exerts upon the filter cake. 'A. The erodabilitv of the filter cake. 4. Any change in filter cake characteristics attributable to the scouring action of the mud. The rate at which solids are deposited from the mud will be controlled to a large degree by the filtration characteristics of the mud, the pressure differential. the temperature under

Jan 1, 1952

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

For the use of those who prefer manila rope to wire rope for light hoisting and hauling, the Ingersoll-Rand Co. has brought out a new model Little Tugger Hoist which is designated No. 11. The square piston, reversible driving engine, automatic lubrication, inclosed gearing, rum release clutch and worm-operated band brake are essentially the same as in the No. 1 model which was introduced about two Years ago. The main differences are in the diameter and length of the drum, the width of the flanges and, necessarily, the main frame and overall dimensions. The new No. 11 Little Tugger has a hoisting drum 7 in. in diameter by 17 in. long with 5-in. flanges. This accommodates 300 ft. of 7/8 -in. manila, rope. The maximum capacity of this hoist is conservatively rated at 600 1b. The weight of the hoist itself is 358 lb. It is 21 ½ in. long, 31 ¼ in. wide and 23 in. high.

Jan 12, 1916

By N. M. Parikh, T. J. Koppenaal

The strengthening mechanism of fiber-reinforced silver has been investigated as a function of fiber density and fiber material. Stress-strain curves were determined in the range 2 x 10-6 to 2 x 10-3 plastic styain and slip lines were examined. The yield strength at 0.2 pct permanent strain is markedly dependent upon fiber density but the stress necessary to initiate plastic deformation is independent of fiber density. The strengthening mechanism of the fibers is shown to be malogous to grain boundary strengthening in poly crystalline metals. The variation in strengthening with different types of fibers is also noted and discussed. In recent years, considerable progress has been made in the understanding of the mechanical properties of two-phase systems, particularly in the classical dispersed-phase alloys where the separation between the dispersed phases is 0.01-0.1µ. However, little work has been done on fiber-reinforced metals where the dispersed-phase separation is considerably larger than this. Parikh1 investigated the mechanical properties of many fiber-reinforced metals and found that two general relationships are always observed, as follows: 1) A fibrous network incorporated into a second weaker metal strengthens the latter, and the amount of strengthening increases with fiber concentration. 2) At a corrstant fiber concentration, the amount of strengthening in a given matrix can vary considerably, depending upon the type of fiber employed. The object of the present investigation was to examine the fuiidamental factors controlling these two observations. procedure: Fig. 1 shows the initial step in the fabrication of the specimens. The sieve is shaken so that the fibers fall into a mold with the longitudinal axes of most fibers in the X-Z plane. The fibers are then compressed to a predetermined density, thus forming a "felt", and the necessary amount of matrix metal is added to the top of the felt. The mold is heated, in vacuum or hydrogen, to above the melting point of the matrix metal; the molten metal flows into the felt, and the entire assembly is cooled. This produces a "composite" that is essentially free of voids. A number of composites were prepared in this manner using 1/4-in. kinked lengths of mild steel

Jan 1, 1962

By R. A. Hancock, L. C. Uren, G. V. Feskov, P. P. Gregory

The resistance to flow of mixtures of gas and oil in passing up through the flow tubing of oil wells operated by gas-lift or by natural flow is a factor in oil-recovery technic that has received but little attention. Yet accurate design of a tubing installation for a particular set of conditions, where operation is by either of these methods, is impossible without quantitative data on the pressure loss suffered by the oil-gas mixture in its passage through the well tubing to the surface. Because of lack of such information, petroleum production technologists have been compelled to approach this problem by " cut-and-try" methods, which, doubtless in many cases, has resulted in the installation and use of tubing too large or too small for most efficient utilization of the expansive force of the gas used in lifting the oil. Impressed with the necessity for information of this character, the authors have conducted a series of tests with large-scale apparatus in the petroleum engineering laboratories of the University of California, designed to be productive of data that would afford a means of attacking the problem of flow-tubing design on a more scientific basis. Mechanics of Expulsion of Gas-oil Mixtures in Naturally Flowing and Gas-lift Wells When oil is lifted from a well by the expansive force of compressed natural gas or air, the fluids enter the lower end of the eduction tube under elevated pressure, with the gas partly in solution, but largely distributed in the form of occluded bubbles within the oil mass. As discharged from deep wells, after reaching the surface, there will normally be at least 60 times as much gas, by volume, as of oil; and in many cases the ratio of gas volume to that of the oil will have a value as great as 1000 or more. On entering the lower end of the eduction tube, however, a relatively smaller volume of gas will be found in the oil-gas mixture, on account of compression of the gas in accordance with the elevated pressure necessary. If the pressure at the point of admission to the

Jan 1, 1930

By G. P. de Forest, G. O. Hiers

The object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line; (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the results of Miller,' by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-curve experiments and microscopic examination reported here. Solution of Copper in Molten Tin To determine the amount of copper that would be dissolved by molten tin at a given constant temperature the apparatus shown in Fig. 1 was used. It consists of a cast-iron pot a, 6 in. deep and 8 in. dia., well cleaned inside and dressed with graphite. This pot, which holds 15 lb. of tin, g, rests on a hot plate b with resistance winding c. The thermocouple d leads to a Wilson-Maeulen temperature regulator for maintaining the temperahre at the heating coils at a fixed temperature to within ±5°C. There is a shallow bath of solder e on the top of the hot plate to improve the thermal contact between the plate and the pot. An insulating jacket f of asbestos prevents the irregular radiation of heat from the apparatus. The copper stirrer h slowly rotates in, and is dissolved by the bath of molten tin g. This bath is protected from excessive oxidation by a layer of charcoal j. The stirrer h is fixed to the lower end of the iron tube k, which is so mounted that it can be driven by a motor with reducing gear. The temperature of the bath is indicated

Jan 1, 1930

By C. E. Corson

The experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of' annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent. of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to

Jan 1, 1907

By A. S. Koster, G. D. Rieck

X-ray experiments were carried out to show the occurrence of cylindrical texture in drawn tungsten wire. Only a small amount of (110) (110) cylindrical texture could he found in wires of intermediate thickness, i.e., of about 1.5 mm diameter. DRAWN wires of tungsten and other bcc metals like iron and molybdenum show a well-established (110) fiber texture. Now it might be conceivable that in drawing radial stresses remove the randomness of the crystallites around the [110} axis, thus giving a fiber texture of higher symmetry. In the resulting so-called cylindrical textures a specified plane normal coincides with the radius of the wire. Several authors discuss the occurrence of cylindrical textures in bcc metals. ~ieck' found no cylindrical texture in drawn tungsten wires of 165 n diameter. Leber~ states that in tungsten wires of 3 mm diameter a cylindrical {100)(110) texture is developed, which is gradually converted to a normal fiber texture by subsequent drawing. He also reported a definite cylindrical texture at the surface of iron wires. Peck and Thomas3 observed a nonuniform mode of deformation of the grains in transverse sections of heavily drawn tungsten and iron wires. According to Bhandary and cullity4 a swaged iron wire has neither a perfect (110) fiber texture nor a perfect {100}(110) cylindrical texture. It is clear that the concept of cylindrical texture in bcc metals still lacks a firm experimental basis. Leber's eviden~e,~ which seems to be the strongest, rests upon qualitative interpretation of photographs. The appearance of the 110 and 200 lines on the photograph of 3-mm wire, however, can be very well attributed5 to a normal ( 110) fiber texture superimposed on random background; our Fig. 1, giving a Debye-Scherrer diagram of etched tungsten wire of 180 p, is free of cylindrical texture according to all authors, but is quite similar to Leber's diagram. It was therefore decided to use a different method of X-ray texture determination on tungsten wires of diameters where cylindrical textures may be expected.

Jan 1, 1965

By Jacques B. Wertz

Among the parameters to be considered in the continuous search for new base-metal deposits, there often is a stratigraphic controlling factor that seems instrumental in the localization of ore. In British Columbia, for instance, the Upper Triassic as well as Lower Jurassic volcanics mixed with sediments are a useful indication in the search for copper while, in some parts of Australia, rhyolite bodies seem to be the favorable indicator, and this always within the geosynclinal environment. In Arizona, this stratigraphic factor becomes highly significant and it will be shown here that a large number of ore deposits are to be located around the flanks of ancient calcareous basins or depressions, preferentially corresponding to a certain optimum thickness as revealed by isopachs. The Martin limestone, of Devonian age, is already known for its basal O'Carroll bed which coincides with mineralization at places, and this is a relatively minor control. However, several limestone basins outlined by isopachs are in reality of greater importance as they localize mining districts. Indeed, most mines are found to coincide with a specific thickness of limestone while occurring simultaneously close to major, regional fracture intersections. The regional fractures in question were interpolated and extrapolated from known, important fault expressions, integrating quite well with the existing geology and further confirmed by minor criteria such as contacts, igneous plugs, axes of elongation of batholiths, dikes, etc. Although elements of subjectivity remain, this grid of fractures can be used quite successfully as a working hypothesis in the search for ore. Results of the present study which superposes major structural

Jan 1, 1971

By Alan Morris

IMPINGEMENT attack, as one of the types of corrosion suffered by condenser tubes, has been given a prominent place in corrosion literature of recent years. It has been reproduced and studied in carefully controlled laboratory tests. Much has been learned of its mechanism, and of the effects of variables such as temperature, amount of air, size of bubble and water velocity. Incidentally the technical public has been given comparisons between the behavior of some few metals under various conditions of impingement attack. The tests recorded here were undertaken in an effort to find at least some sort of qualitative answer to questions which arose occasionally as to the relative resistance of various alloys to impingement attack, and which could not be answered by reference to the literature. The final decision to start work on the problem was influenced in large measure by the nature of the water available in this particular place. The mill of the Bridgeport Brass Co. is located on the Pequonnock River at Bridgeport, Conn., within two miles of its mouth. The water is much like many other estuarine sources which are used in condensers, and which cause particularly severe corrosion. It seemed a most suitable water to use in such tests. As the work progressed an important seasonal variation was noted. The purpose of this note is to record this seasonal effect. The results of individual tests are given only incidentally.

Jan 1, 1931

By Timothy Collins

There was once a speculative period of interest in small mining companies that is commonly referred to as "the uranium boom of the 50's." In the late 60's, there was a second mining stock boom: it centered around uranium and silver, when silver had reached a new high of $3.60. In the mid 1970Js, there may be a new boom in the making, and it appears that substantial public and institutional interest in mining equities will finally result in a viable long-term capital market rather than the boom-or-bust pattern of the 50's and 60's. The reason for Wall Street's renewed interest in mining is understandable: most mineral commodities have recently gone up in price. Domestically, these price increases have come in the wake of the inflationary spiral unleashed by years of unbridled government deficit spending and erratic fiscal and monetary policies. Internationally, of course, the biggest push for higher prices has come from third-world countries whose primary income derives from indigenous natural resources. Many of these countries-whose fiscal and monetary policies haven't been models of excellence either-have attempted to cope with the worldwide economic mess by forming cartels that could control the price of commodities. What's happened to petroleum is well-known; what's happened to copper, bauxite, phosphate, and uranium is part and parcel of the same syndrome.

Jan 9, 1975

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By A. C. Dorenfeld

In most mineral enterprises, what is the progress, and shift in responsibilities, as the young engineer advances in the corporation? You are all familiar with the normal pattern-in mine production from level boss, to shift boss, to superintendent to manager; in milling from test engineer, to shift boss, to foreman, to superintendent and then manager; in engineering from surveying on to Chief Engineer; and all then aspire to the corporation presidency. Note the shift-from purely technical jobs, say in the first five to ten years in the profession, to administrative positions for 30 to 40 years. What is the average preparation given to mineral engineering students, who can look forward to about 30 years of administrative work? From the catalogs of 21 institutions, offering 36 curricula of four years length, in mining and/or metallurgy, requiring the equivalent of about 150 to 160 semesterhours for graduation, the following results were obtained: Average number of semester hours of economics, 3 hr. Range of requirements, 0 to 8 hr. Thirteen curricula do not require any economics. Accounting and business law, average: 1 semester hr, 26 curricula do not require business law or accounting.

Jan 2, 1955

By D. B. Crouch, D. A. Poulter

The engineering and metallurgical assessment of the McLaughlin Project ore body concluded that an open-pit mine and cyanide leach mill process would be feasible, producing both waste rock and residual mill tailings. As a part of the planning and permitting process, site selection studies were conducted for the tailings and waste rock disposal. The site selection process began with a regional identification of potential disposal sites and proceeded through 1) regional screening, 2) elimination of sites with obvious fatal flaws, 3) qualitative ranking of site evaluation criteria, 4) quantitative ranking of sites, 5) field investigation, 6) evaluations of field data, and 7) selection of preferred sites. Based on this approach of site rankings and field evaluations, tailings and waste rock disposal sites were selected and recommended for the preliminary design phase of the permitting and project development process. The site selection study provided the documentation necessary to justify the use of these sites for waste disposal and enabled Homestake Mining Co. to anticipate and integrate environmental concerns with agency requirements into the planning process.

Jan 1, 1986

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969