Search Documents

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

By R. Stanford

In any discussion of steel pouring too often refractories quality assumes a high level of importance. Unfortunately when one considers the many and varied conditions to which pouring refractories are exposed, it is difficult to isolate the true role of refractories quality alone. Some of the more important, yet often overlooked, variable conditions bearing on pouring performance are heat size, tap time and temperature, steel chemistry, ladle additions, ladle height and preheat, mechanical conditions of the pouring mechanism, hot top or non hot topped ingots and, ingot size, which determine total number of shutoffs, direct or tundish pouring, ingot filling rates, metallurgical demands, etc, etc. These considerations apply for either conventional or slide gate pouring of ingots and, to a large extent, even strand casting. In any event probably the most significant factor on pouring performance in any individual shop is what is considered an "OK" pour. We find considerable variance in this qualification, not only between Republic Steel meltshops, but throughout the industry. Therefore, it is a worthless exercise to draw comparisons attributable to refractories quality alone, except for similar conditions in a single shop.

Jan 1, 1972

By Didyk M. Marko, Vásquez Ñ. Gregorio

INTRODUCTION The Salvador Division of Codelco Chile is an important copper molybdenum production center, located 1,200 km north of Santiago and 124 km east of the Pacific Ocean, in the foothills of the Andes Range. El Salvador Mine produces by block caving 8,600,000 t of ore with a content of 1 .l0% Cu and 0.02% Mo, from a copper porphyry ore body. The geology of the ore body shows a great heterogeneity as to rocks, grade distribution, ore height and undercutting levels. This has resulted in a variety of designs for the productive units (blocks) and in the mineral handling systems. Up to now, 4 systems have been employed: grizzly and intermediate haulage; slusher drifts with intermediate ore pass and haulage; slusher drifts with scraper loading directly into trains; and, LHD. On the other hand there is a marked dispersion in the final results from each block mined out. We report here the conclusions reached after analyzing the data gathered on the mining of 163 depleted blocks, representing a total production of 102,000,000 t, with an undercut area of 340,000 sq m. The final results of each block, characterized in terms of tonnage and fine cop- per recovery, were studied as a function of a number of design, geological, and operational parameters. BASIC CONCEPTS Indices of Efficiency In order to evaluate the final result of each block, or group of blocks, the following indices of efficiency were defined : Tonnage Recovery (TR) . It is the ratio between the ore tonnage extracted and the in situ tonnage estimate for each block or group of blocks. Grade efficiency (E) . It is the ratio between the Cu mill feed grade and the in situ Cu grade estimate for each block or group of blocks. Grade efficiency is numerically equal to the ratio between fine copper recovery (FR) and tonnage recovery (TR) . Figure 1 shows the final results for 163 mined out blocks, in terms of tonnage and fine copper recovery. Different grade efficiencies are also indicated. The marked dispersion in the final results of mined out blocks must be stressed since it greatly incides in mine planning. It must be kept in mind that an eventual concentration of low overall efficiency in the blocks during a given period (e.g., one year) will make it necessary to bring into production new blocks over the standard development schedule. It is worth noting that the final results in the 163 mined out blocks corresponding to a production of 102,000,000 t of ore with a mill feed grade of 1.445% were obtained from an ore estimate of 93,000,000 t and a grade of 1.671% Cu, which represents 110% tonnage recovery and 86% grade efficiency. Parameters Studied The following parameters are considered in this study: Geological Parameters. These parameters depend exclusively on the geological and geotechnical features of the ore body. IN SITU GRADE: The initial estimate of the block grade. Four copper grade categories were considered : (a) lower than 1.3% ; (b) 1.3 to 1.6%; (c) 1.6 to 2.0%; (d) higher than 2.0%. The overall initial in situ estimate of the ore body was 1.6% Cu. IN SITU TONNAGE: Initial tonnage estimate of the block. Four categories are considered: (a) below 500,000 t; (b) 500,000 to 1,000,000 t (c) 1,000,000 to 1,500,000 t; (d) over 1,500,000 t. CONTACTS SLOPE: Since up to 4 rock types can be found in a block, resulting in a corresponding number of contacts, a horizontal con- tact was defined as that which forms an angle of less than 45" with the horizontal and a vertical contact that which forms an angle of more than 45" with the horizontal. GRADE DISTRIBUTION: As in rock types, horizontal and vertical grades were defined. ORE HEIGHT: The distance measured between the undercut level and the top of ore. Four categories are considered: (a) less than 60 m; (b) 60 to 100 m; (c) 100 to 150 m; (d)over 150 m

Jan 1, 1981

By W. L. Dennen, V. H. Wilson

THIS paper is a description of the opera¬tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery of The Hudson Coal Co. during the first nine months of operation and follows a pre¬liminary description given at the Anthracite Institute in May, 1947, in a paper titled "Preparation of Anthracite Sift for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size operating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig 1 and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which handles the Breaker waste water. This underflow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped .to vibrating screens where the plus 316-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine

Jan 1, 1948

By Richards R. Vandervoot

T HE creep behavior of many polycrystalline metals at moderate stresses can be described by the empirical relationship: where Em is the minimum creep rate, A is a constant, a is the applied stress, E is the average elastic modulus at the test temperature, and D is the self-diffusion coefficient.&apos; This equation is generally applicable for strain rates of less than around 10-5 per sec and temperatures greater than about one-half the melting point in absolute units. Under these conditions atomic mobility plays an important role in the deformation process, and steady-state creep occurs when a dynamic equilibrium is reached between the generation and recovery of dislocation substructure. Although several theoretical mechanisms have been proposed to explain the creep of polycrystalline solids,2"4 the dislocation climb model2 is in accord with most experimental observations. The majority of creep data used to develop Eq. [1] came from metals with either the fcc or hcp crystal structures. However, on the basis of results for a and 7 iron as well as those for a and a thallium, Sherby concluded that the high-temperature deformation behavior of close-packed metals and bcc metals is probably the same.&apos; The greater creep resistance of fcc and hcp metals and alloys on a relative temperature scale was attributed to lower diffusivities in the close-packed structures. To further compare the creep properties of fcc, hcp, and bcc metals, creep data for all six bcc refractory metals were analyzed according to Eq. [I]. The results are shown in Fig. 1. The sources of information for the quantities used to prepare this figure are listed in Table I, except for high-temperature elastic moduli. The latter data were obtained from Refs. 28 and 29. The dashed lines in the figure represent the range and breadth of data analyzed by Sherby for fcc and hcp metals. In general, the deformation behavior of all of the refractory metals, ex- cept possibly that of tungsten, can be represented by Eq. [1]. This correlation is strong evidence of the similarity that exists between creep of pure close-packed metals and creep of pure bcc metals. At (Em/D) < 108, the results of Flagella and Tarr on tungsten (W-1 in Fig. 1) agree with the five-power stress law, while those of Green (W-5 in Fig. 1) show a seven-power stress dependence. Where (Em/D) > 108, the stress exponents for other data on tungsten were in the range 10 to 15. It is possible that the creep rate dependence on stress in this region is not a power law but exponential (i.e., Em - eßo). However, it was not feasible to differentiate between these two cases because of the steep slope and scatter in the data. Note the inflection point in the curve for the data of Flagella and Tarr (W-1 in Fig. 1). The slope of the line changes from 5 to around 10 at Em/D = 108. The breakdown of the fifty-power stress law at high stresses is not uncommon in other metals, and this phenomenon may result from nonequilibrium conditions in the material such as excess lattice vacancies produced by rapid straining.30 The mechanical strength of a polycrystalline metal is related to its microstructure. Attempts to establish the influence of grain size on the creep rate of metals and alloys have led to a wide variety of results. For example, the following effects have been observed: creep rate decreases as grain size increases;31&apos;32 creep rate decreases as grain size decreases;&apos;,33 creep rate is a minimum at some critical grain size and increases with either an increase or decrease in

Jan 1, 1969

By R. G. Ward, P. L. Sachdev

Using an improved maximum bubble pressure technique, the densities of iron silicates at 1400°C have been measured under nitrogen. At the wiistite composition the density has been measured by bubble-blowing experments with both argon and nitrogen and calculated from the measured volume of a known mass of melt under nitrogen. The densities under nitrogen are significantly different from those measured under argon for melts containing less than 28 wt pct SiO2. THE constitution of liquid slags is not well understood, largely because no single property or parameter can be measured which gives conclusive evi- dence of the types and packing of the ions present. Of the many property measurements which can provide information leading to a picture of the constitution of slags, density gives the most direct evidence and has been studied extensively. The work reported here is part of a program of study of densities in multicomponent melts in which the iron oxide-silica system is the solvent. These melts are important as they are fundamental to basic steelmaking, and they allow the study of basic silicate compositions which have hitherto been largely neglected. As considerable disparity exists

Jan 1, 1965

By Marvin Lee

Kansas continued holding, for its seventh year, the fourth position in the list of oil-producing states. The crude-oil production, according to purchaser&apos;s reports to the State Corporation Commission, was 40,008,940 bbl.; as assembled by the Oil and Gas Journal, 41,305,768, and by the U. S. Bureau of Mines, 41,942,000 barrels. Increase of production from 1932 was largely due to greater stability of the industry, and increased return of demand for Kansas oil, caused by the addition of Federal assistance in national production regulation which reduced illegal production, of some areas out of Kansas, that had been destructively competing with Kansas crude or its refined products, at less than cost of production. Prices continued to advance from the lowest level of 25c per barrel during part of May and June, until by the end of September 36" gravity crude had reached $1 per barrel and continued at this price the remainder of the year. Price stability, for a period greater than in previous years, has brought renewed confidence to those producing oil and has led to renewed interest and increased purchases of Kansas leases. Drilling was confined chiefly to the number of wells necessary to protect from offset and other drainage in the field and to meet the requirements of expiring lease contract deeper areas in Mid-Continent, are an added inducement to exploration. The renewal of interest in the search for new fields in Kansas is already apparent and 1934 will probably see more wildcatting than for several years. This is due both to the expiration of leases on large blocks and to actual demand of the industry for new fields. Exploration for favorable areas is being actively conducted by the various methods of surface, subsurface and core drilling and geophysical work. Much of western Kansas cannot be mapped by surface study and geophysical exploration has been of considerable assistance and has led to a large use of the seismograph. Several companies are conducting seismograph surveys and leasing on findings already secured. Development under the more favorable conditions of 1933 can be readily seen by the comparison of the following reports for the last weeks of December in the respective years.

Jan 1, 1934

The difficulty of finding new ore bodies, the complexities of patenting them when they are found, and the absence of incentive legislation for exploration have limited mining exploration in the United States mostly to the big companies. This situation, coupled with ECA spending abroad, has caused American capital to look outside our national boundaries for investment opportunities which are further made attractive by some relaxing of restrictions to gain American dollars and patronage.

Jan 1, 1950

By Leonard Klein

Reduction of oxygen-containing copper has always heretofore been brought about with wood poles. This paper reveals the first successful, economical, and Practical substitute for poles: a gaseous reductant, of which the production and plant use are detailed herein. THE art of fire refining of copper, consisting of melting, oxidation, slag removal, and finally reduction with wood poles, has been practiced for many centuries. An authentic record, discussed in detail in De Re Metallica,* mentions that as early as 1200 A.D. workers in this field of metallurgy were already acquainted with and practiced the basic principles of copper purification. Undoubtedly, the art was well developed marly centuries before the first written records began to appear. Notwithstanding the many advantages gained by application of mechanical con. trivances and by the tremendous increase in size of operations over the centuries, the reduction phase of the process has persisted essentially the same to the present time except for a very recent breakthrough. Numerous articles have been published and many patents have been issued on the subject of substitutes for wood poling in the past half century. They have dealt with a variety of gaseous, solid, and liquid reducing agents. But to the knowledge of the writer, no procedure has ever been prosecuted to a complete success on a large operating plant scale with the single exception of gaseous reduction of oxygen-containing copper revealed in detail herein. A natural gas-air reformer with ample capacity for

Jan 1, 1962

By Walter Mueller

Transition in the underground coal industry, begun with the passage of the Federal Coal Mine Health and Safety Act of 1969, should be completed midway in the 1972-80 period. Surprisingly, many of the far reaching effects of this act have been, for the most part, beneficial to the industry from the standpoint of health, safety and basic operating standards. Production has dwindled, but the next few years will see production declines level out. Average declines of approximately 27% have been recorded since passage of the 1969 act, with costs increasing an average of $1.50 per ton throughout the industry. Nationwide averages presently are in the range of 14 tons per man-shift, and by 1980 this may be further reduced to a 10-ton per man-shift average for the industry. But in spite of the many temporary set-backs affecting the industry, the marketing opportunities are clearly visible. Due primarily to the energy squeeze facing the U.S. over the near term, the &apos;underground coal operator is and will be enjoying unusual leverage in selling his product.

Jan 10, 1972

By M. Paulus

It is known that multicomponent powders are mostly nonhomogeneous. This paper investigates the effects of nonhomogeneity of composition and grain size on the melting point and the sinterability of compact taking into account homogenization mass transport and the length of the diffusion path in solid state sintering, and the kinetics of liquid phase formation in liquid phase sintering. After a discussion on the ideal characteristics of a powder for sintering and low temperature reaction, the main conventional processes are compared. Finally we develop the freeze-drying technique and demonstrate the capabilities and the limits of the process by some examples, mainly in the ceramics field.

Jan 1, 1980

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By A. W. Ross, William Marsh Baldwin, T. S. Howald

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip&apos;-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves&apos;5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By William Marsh Baldwin, T. S. Howald, A. W. Ross

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip&apos;-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves&apos;5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By C. W. Wahsburne

Former studies of sedimentatry strata have been based upon the mineralogical and mechanical characters of the solid components, rather than upon the open spaces between them.

Jan 1, 1915

By L. C. Brown, J. S. Kirkaldy

Measurements have been made of carbon diffuswn in the five ternary austenites Fe-C-Si, Fe-C-Ni, Fe-C-Co, Fe-C-Mn, and Fe-C-Cr in which the carbon (component 1) diffuses through interstitial sites and the ternary addition (component 2) diffuses substitutionally. Values of the diffusion-coefficient ratio, D12/D11 were determined for each system with finite couples using the transient equilibrium method. The effect of temperature and of concentrations of both the carbon and substitutional component upon D12/D was examined and was found to agree with the theoretical predictions. It is concluded that within an experimental uncertainty of 10 to 15 pct, it is possible to calculate the ratio D12/D11 from purely thermody-namic data. Difficulties of measuring the other off-diagonal coefficient, 4,, are discussed. Any quantitative attack on the fundamentals of the hardenability problem in steel must begin with the multicomponent diffusion formalism and with the accumulation of data pertaining thereto. In a recent paper Kirkaldy and purdy 1 employed the formalism derived from irreversible thermodynamics to treat the problem of diffusion in ternary austenites. In the latter solutions, carbon diffuses through interstitial sites and the substitutional component diffuses through the lattice. Examples were given of diffusion in the systems Fe-Mn-C and Fe-Si-C. In the present paper, we present new results on and discuss their agreement with the thermody-namic theory. Since the theory has been slightly modified from the original presentation of Kirkaldy and Purdy, their results on Fe-Si-C and Fe-Mn-C have been recalculated and are presented here for completeness. The flux of the interstitial component with respect to a fixed lattice framework can be written as a linear expansion in the independent concentration gradients, where X1 and X2 are the independent thermody-namic forces in the lattice fixed frame of reference. These forces can be obtained from the general statement for forces in a volume fixed frame2 if the partial molar volume of carbon atoms is set equal to zero and that of the substitutional component 2 is set equal to unity, viz where the are the chemical potentials and the N&apos;s are mole fractions. Introducing into [3] and [4] the function If, as suggested by statistical arguments, the off-diagonal interaction L12 is sufficiently small, [6] reduces to i.e., the coefficient ratio becomes purely thermo-dynamic. The activity of components 1 and 2 in a dilute ternary system (standard state at infinite dilution) may be represented by the expansion3

Jan 1, 1964

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc at temperatures below 200°C has been studied using both single crystal and polycrystal samples. Anomalous results were obtained for single crystal samples, the data indicating that in some cases grain boundary diffusion predominated. These anomalous results are presumed to be due to low angle lineage boundaries in the single crystals. When volume diffusion occurred in either single or polycrystal samples, the values for the diffusion coefficient were as much as several orders of magnitude larger than would be expected from high temperature data. ONSIDERABLE work has been done on self-^-*diffusion at temperatures in the neighborhood of two thirds of the melting temperature (in OK) and higher, but very little has been done at lower temperatures. This is particularly true of self-diffusion in single crystals. This paper reports work on self-diffusion in zinc at temperatures below 200 °C where both polycrystalline and single crystal samples have been used. The measurements were made using both the sectioning and absorption techniques. The experiments on diffusion at low temperatures were initiated primarily for three reasons: to obtain data from single crystal diffusion covering a wide range of temperatures, to obtain values of the activation energy for grain boundary diffusion, and to obtain, if possible, a lower limit to the temperatures at which the absorption technique may be used. It is possible to determine whether volume or grain boundary diffusion predominates at low temperatures by analyzing the manner in which the concentration of the diffusing atoms varies with the depth of penetration. The analysis is possible only for the sectioning technique. For volume diffusion and for the boundary conditions of the present experiment, the curve of the logarithm of the concentration, C, vs the square of the penetration depth, x, is a straight line with the slope proportional to — 1/D. If grain boundary diffusion predominates, Fisher&apos; has shown that a curve of In C vs the first power of the penetration depth should be a straight line. This linear dependence of concentration on depth has been observed experimentally by several investigators. (See, for example, refs. 3 and 4.) Following Fisher&apos;s analysis, the grain boundary diffusion coefficient can be written as where 8 is the grain boundary width, D, is the volume diffusion coefficient at the temperature involved, t is the time of diffusion, C is the concentration of diffusing material, and x is the depth of penetration. A more general analysis employing the same model as Fisher&apos;s but with fewer assumptions has been given by Whipple.&apos; In contrast to Fisher&apos;s analysis the more general analysis of Whipple does not always yield a straight line relation between In C and x. Recently Turnbull and Hoffman have discussed both analyses and have applied the Fisher-Whipple model to a more refined dislocation model of the grain boundary. They have also discussed the possibility of a large effect of grain boundary direction on diffusion. In the case of the absorption technique, for which results are also given, one simply gets a value for the diffusion coefficient with no indication of the predominating mechanism. Experimental Techniques Single crystals of 99.99+ pct Zn were grown using a modified Bridgman method. Polycrystal samples were prepared in three grain sizes (small, about 4 mm2; medium, about 9 mm&apos;; and large, about 25 mmz) by quenching, air cooling, and furnace cooling. The grains of the polycrystalline samples tended to be columnar, with some preferred texture such that the c-axis was inclined at about 20" to 25" from the normal to the diffusion face, particularly in the medium and large grain size samples. The samples were cut from the rod, polished, and heavily etched, and faces cut accurately parallel using a jeweler&apos;s lathe. They were again etched to remove the lathe smear and annealed for 3 hr at 250" to 300°C. After annealing, they were etched, examined, and the orientation determined by Laue back reflection photographs. They were then electroplated with Zn. The plated surfaces were examined for uniformity; nonuniform coatings were removed by etching and the samples replated without additional preparation. For the diffusion anneals, the samples were placed in pairs, with active faces together, in evacuated Pyrex tubes. Constant temperature baths were used, and the variation in temperature did not exceed ±l°C, Diffusion runs were made at l00°,

Jan 1, 1957

By B. K. Mozumdar

This paper describes the development and application of a dynamic simulation model of ground movement in an underground mine. Ground movement and related stress distributions with or without stowing are computed as the mining face advances. Pressure profiles plotted for different face positions indicate the presence of a front abutment with a maximum value of four times the original ground pressure but no back abutment in the gob. The surface strain is considerably reduced with increase in packing density in the gob up to a certain value. Beyond this value, the reduction in the strain is minimal, indicating an economic level of packing. As a result of model experiments with different physical systems and geological parameters, it has been concluded that when one of the coordinates for the subsidence and the strain curves is made dimensionless in terms of the critical width, the relationship will hold true for all physical situations. This was in agreement with the NCB observations for different panel lengths.

Jan 1, 1977

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby&apos;s pole mechanism are discussed in detail by Venables.&apos; In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

W. D. BRENNAN,* Cheyenne, Wyo. (written discussion?).-My experience has been that, where possible, it is preferable for each foreman to employ his own men, rather than to have them handled through an employment bureau. The fact that each foreman comes into direct contact with the man before he is put to work gives him an opportunity to choose, at certain times, the kind and class of men that he wishes. Where possible, after a man is employed he is sent to a central office where a complete history of each individual is kept on a card. If a man has previously been in the employ of the Company, his history can be obtained from this card, and if for any reason he is not wanted he can be refused work at the time he reports to, the central office. In connection with Workman&apos;s Compensation costs, we in Wyoming feel that although the rates of compensation paid may in some cases be rather low our law works satisfactorily. As the State and the number of employees are small, compensation cases are handled through Judges of the various District Courts. In the State Treasurer&apos;s Department, a few clerks were added to look after the handling and issuing of warrants and compiling of statistics. Most of the large employers have an arrangement by which a joint claim and assent, specifying the amount of compensation due, is made tip by the employer and signed by the workman. This is forwarded, to the Judges so that personal investigation of individual cases is not necessary. In this manner, compensation is promptly received and&apos; overhead expenses of operation of the law is kept at the minimum. The law requires each employer to pay into the State Treasury, for the benefit of the industrial fund, a sum equal to 1.5 per cent. of the money earned by each employee, engaged during each calendar month of such employment. Each employer contributes monthly, unless the sum heretofore contributed, after deducting all payments made on account of injuries to his employees, shall equal a full 1.5 per cent. of his annual pay roll, computed by multiplying his current monthly pay roll by twelve, and shall likewise be not less than ($5000). It has been found during the years that this law has been in effect, that a number of the larger employers have been exempt from payment for from five to eight months per year, so that in some cases, even in coal nines, industrial insurance has cost less than 0.75 per cent.

Jan 3, 1919