Search Documents

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be compared with field work. The same applies to geological contacts. Once these have been 3stablished at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson's ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young's modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott's work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger's single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By C. D. Rugen

GROUND raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grindability characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. CHARACTER OF GROUND RAW MIX (KILN FEED) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size, whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1945

By O. H. Hahn

I have lately had occasion to conduct a campaign at the works of the Empire City Company, in Railroad District, Elko County, Nevada, which, if not highly satisfactory, was at least very interesting in a technical point of view, and which I therefore think worthy of communication to the Institute. The lead ores in this district occur in lenticular masses along and near the contact of crystalline limestone with a dioritic porphyry, and consist of argentiferous carbonate of lead and galena, the latter occurring in solid blocks, or in ribbons running through the limestone. Associated with these are silicate, carbonate, and suboxide of copper, and brown and calc-spar. Adding to this, that the proportion of galena in the ore is small, and that no iron pyrites exists in the district, it is at once evident that the ore-mixture is difficult to treat. For a successful reduction by smelting, it would be necessary to introduce into the charge: 1. The proper quantities of sillphur-bearing ingredients, to effect a complete separation of copper and lead; and, 2. Sufficient silica and iron oxide, to form with the lime and magnesia of the ore, a slag of the required fluidity. The first condition could be fulfilled only very imperfectly, there being no iron pyrites in Railroad, nor in the surrounding districts. The nearest occurrence is in Battle Mountain, whence a supply could not be procured in time. The second condition, i. e., the addition of iron ore and quartz, was easily complied with, there being an abundance of these materials in the vicinity. The furnace of the Empire City Company, is a small shaftfurnace, with an area of hearth of six square feet, and is supplied with blast by a NO. 4 Root blower. In spite of this small size the furnace smelted during this campaign, which lasted 31 days, an average of 28 tons of ore, and 13 tons of fluxes, together 41 tons of charge, per twenty-four hours. The following tables give the complete data in regard to the smelting process, and the results obtained:

INSTITUTE MEDALS AND PRIZES ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows The Robert W Hunt Medal, The Hadfield Prize, The J E Johnson Jr , Award, The Lewisohn Platinum Prize to senior members, and the President's Prize to junior members ROBERT W HUNT MEDAL The partners of Robert W Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules, 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to, the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee consider¬ing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improve¬ment of production and quality of material 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute 5 The recipient of the award shall be designated "The Hunt Medallist "

Jan 1, 1923

By J. S. Diller

In 1827, chromite was discovered near Baltimore by Isaac Tyson, Jr., who initiated the mining of chrome ore an:! later (1845) .the manufacture of chromium compounds in this country. From 1828 to about 1860 the United States, supplanting Russia, supplied chromite for most of the world. Chrome deposits were found also in California, and the Tyson Company shipped ore to Philadelphia by way of Cape Horn. In 1848, J. Lawrence Smith, an American in the employ of the Porte, discovered large bodies of chromite in Asia Minor. They were developed in 1865 and became the chief source of the world's supply for a number of years. The discovery of the large high-grade bodies in New Caledonia, and later in Rhodesia, with other foreign sources, gives at present an abundant supply for all demands. For a number of years before the great war, the United States produced only a few hundred tons of chromite annually, for local use, but during the war the demand for domestic ore resulted in a production of more than 82,000 long tons of crude ore in 1918, and it was demonstrated that the United States has reserve deposits equal to a war demand of several years' duration. Now that the war is over, the country is conserving its domestic supplies by employing higher-grade but cheaper ore from foreign countries. ChromiUm-bearing Minerals Oxides: Chromite-—chromic iron ore................ FeO.Cr2O3 Picotite—chromic iron ore................. (MgFe)O.(Al,Cr) Chromates: Crocoite—lead chromate................... PbCrO4 Phoenicochroite—basic lead ohromite........ 3PbO.2CrO3 Vauquelinite—phospho-chromate of lead..... 2(PbCu)CrOd.(PbCu)3P2O8 Sulfates: Redingtonite—hydrous chromium sulfate.... Knoxvillitel—hydrous basic sulfate of chromium.............................. Daubreelite-—iron-chromium sulfide (known in meteorites only)...................... FeS.Cr2S3

Jan 1, 1920

By H. W. Hitzrot

*Original Pages Missing From Book

Jan 5, 1954

By E. I. Organick, B. H. Golding

A simple correlation is presented for the prediction of saturation pressures in condensate-gas and volatile-oil mixtures. Saturation pressure is related directly to the composition of the mixture with the aid of two generalized composition characteristics, B, the molal average boiling point, and W, the modified weight average equivalent molecular weight. The need for hydrocarbon equilibrium constants is entirely eliminated. Only the values of the two conlposition parameters need be obtained, and these are calculated in a simple and reproducible manner from the stream analysis of the mixture and the ASTM distillation for the heavy ends. The correlation is given .in the form of a set of 14 working charts in which saturation pressures, either retrograde dew points or bubble points, are plotted cs temperature, forming partial phase envelopes for mixtures having discrete values of the composition parameters, B and Wul. A locus of critical states on each chart intersects the partial phase envelopes, distinguishing retrograde dew point pressures from bubble pressures. A comparison Between experimental and predicted saturation pressures reveals that: the probable error of the predicted values, when considering the data as a whole (214 experimental points), is five per cent; for high gasjoil ratio condensate fluids (approximately 40.000 or more cu ft/bbl) the probable error is about 8 per cent. In either case, however, the probable error is comparable with the overall uncertainty of the data from which the correlation is derived. INTRODUCTION There is a present need for a simplified, yet reasonably accurate method for predicting upper phase boundaries of reservoir fluids. In the case of high gas/oil ratio fluids, namely the so-called highly volatile oils and the condensate gases, no simple method, accurate within 5 to 10 per cent, is now available by which bubble point and retrograde dew point pressures may be predicted. In order to calculate the upper phase boundary of a volatile reservoir fluid, using correlations now available, it is necessary to find and employ the proper K-values (equilibrium volatility ratios of the hydrocarbons in that fluid). This process of finding the Proper K-values usually involves a double trial and error computation. Since the K-values are in themselves dependent upon the composition of the fluid, their use in the calculation of a saturation pressure actually represents an unnecessary complication. The correlation described in this paper relates saturation pressure directly to the stream composition, entirely eliminating the need for K-values. The only data required to calculate the Stream composition are obtained from the customary low temperature fractional analyses of separator gas and liquidt and from the ASTM distillation of the c,+ fraction of the separator liquid. A considerable simplification in the procedure for predicting saturation pressures is thereby effected without significant loss in accuracy. BASIS FOR A CORRELATION Empirical relationships between the saturation pressure and the composition of the fluid in question have already been partially explored by one of the authors.V n particular, a relationship between the critical pressure for a hydrocarbon mixture and its composition was developed. The critical pressure is in reality a saturation pressure, as it repregents a limiting case either of a dew point or of a buhhle point pressure for any given mixture. It was found that the critical pressure may be correlated as a function of two generalized composition characteristics or variables. One characteristic expressed a molal average prop-erty, the other a weight average property of the mixture. Specifically, the molal average boiling point (MABP, or B as it

Jan 1, 1952

By H. l. Burghoff, J. S. Porter

THIS paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 96 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about 10 per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrett1 states the fiber axis of annealed 70-30 brass wire to be [111] with some indication of [100] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. MATERIAL AND PROCEDURE All the wire for the investigation was processed from one. portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02 nickel; 29.83 zinc (by difference). The billet section, 8 in. in diameter, was extruded hot to 3/4 -in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 875°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By W. L. Maxson

GRINDING is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grind-ing installations. There have been some tests published, notably those of Lennox,1 which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was .then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the compari-sons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating, load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to he expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method.

Jan 1, 1933

The suggestions of the members of the Institute are very much desired by the Committee on Nominations prior to deciding upon its nominations to fill the places of those officers who retire early in 1917. The Committee must make its final report to the Board of Directors early in October. The members are, therefore, asked to send in promptly their .suggestions for Directors as well as for Vice-Presidents and President. The Committee hopes to hear from a large number of the members. The officers to be elected at the annual meeting in February, 1917, are: One officer, known as Director and President. Two officers, known as Director and Vice-President

Jan 8, 1916

By K. R. Grube, D. N. Williams

It is often desirable to perform fatigue studies at relatively high strains and at low strain rates. A low-cost fatigue machine has been constructed for this purpose which has proven quite versatile. This machine is based on the principle of repeated bending of a strip sample over a shaped mandrel. A photograph of a group of fatigue tests in progress is shown in Fig. 1. The test sample is held in place between two shaped mandrels having a flat at their base to grip the sample firmly. A cam-driven loading frame is used to bend the sample alternately over each mandrel. The sample slides freely in this frame and is held in place by a light spring to accommodate increases in sample length. The pivot point for the loading frame is selected so as to minimize movement at the loading point during operation. The number of cycles to failure is recorded by a rachet counter which is kept in operation by a series electrical connection through the sample and is operated by the drive cam. The maximum strain imposed at the sample surface on bending from one mandrel to the other is readily calculated from the relationship, where t is the sample thickness and r is the radius of curvature of the mandrels. The rate of straining can be controlled by control of the cam speed. The device as shown in Fig. 1 is set up to run six samples at ambient temperature. A much larger number of samples can be run at one time without difficulty. ALSO-, by slight realignment of the components the mandrel unit can be enclosed in a separate chamber permitting control of test temperature and environment. This permits a variety of fatigue and corrosion fatigue problems to be studied.

Jan 1, 1963

By Robert Ammon

THE milling practice at Mascot, at present, consists of dry crushing to 5/8 in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per. cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. are made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads 3.55 Jig concentrates 61.30 Jig tails 0.80 Flotation concentrates 60.60 Flotation tails 0.09 Extraction 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows:

Jan 9, 1924

By M. J. Greaves

All available data concerning risk as it applies to scaling up pyrometallurgical plants, processes, and equipment are determined to estimate the statistical chance of success. Random numbers are assigned to all data in order to avoid any chance of bias. The data bank is organized in such a way that an estimate can be made of the degrees of risk involved over a wide range of circumstances. Included are duplicating existing designs and large commercial installations based on smaller commercial installations, pilot models, or bench models.

Jan 1, 1977

By W. E. Remmers

The fact that gray iron increases in volume, cracks and distorts upon repeated heating and cooling is rather conlmon knowledge. In ingot molds, Diesel engine pistons, carburizing boxes, continuous furnace parts, grate bars, stoker parts, and all castings that are subjected repeatedly to high and low temperatures, the phenomenon of growth presents a vital problem. Ingot molds distort and produce cracks which result in seams or laps and later appear as defects in the finished product. The heads of Diesel pistons frequently fail by cracking in a stellar shape. This is attributed usually to the result of permanent growth. Distortion and change of dimension of furnace parts frequently renders them entirely unusable. In chain grate stokers, mechanical difficulties frequently are caused by the growth of the links. In proper operation these links should never attain a temperature sufficiently high to start growth; nevertheless, some have grown in. on an 8-in. length when improperly operated. Even though the phenomenon is generally known there still exists a deficiency in the explanation of the mechanism of this growth. The field of investigators of this subject has a decided variation in opinion concerning the causes. The problem is of sufficient importance therefore to warrant further consideration. Review of Published Work Since the published work, particularly the European, contains much detail, only the outstanding results and conclusions of the investigators will be reviewed. The pioneering investigations of Outerbridge in 1904 and 1905 brought forth the conclusion that growth was not a function of chemical or crystallographic changes but was a result of the formation of fine hair cracks. These cracks are supposedly due to a nonuniformity of thermal expansion and contraction which ruptures the structure of the material. More recently Benedicks and Lofquist presented a purely mechanical theory, which is similar to that of Outerbridge. These investigators believe the temperature gradient from the outside to the center of the cast piece causes a contraction of the outer layers on passing

Jan 1, 1931

By Albert J. Phillips

When brasses containing from 61 to 62.5 per cent. copper are very rapidly cooled from temperatures near their melting point to below 0" C., unusual results are obtained. These results are quite unexplainable from a consideration of the old copper-zinc constitutional diagram but they can be satisfactorily explained by means of the diagram revised by Genders and Bailey1 (Fig. 1). Experiments on a 60/40 Brass If an alloy containing 60 per cent. copper is heated to any temperature between approximately 760' C. and its melting point, it will consist entirely of beta. Upon slowly cooling, alpha will start to separate just below 760" C. Since this alpha will contain nearly 65 per cent, copper, the beta will be impoverished by its separation. As the temperature decreases the composition of the separating alpha will approach approximately 61 per cent. and the beta in contact with the alpha will maintain an equilibrium composition approaching 54.5 per cent. copper. If the rate of cooling is extremely slow, especially at the lower temperatures, stable equilibrium will be established by diffusion through the alpha and beta so that eventually 85 per cent. of the alloy will consist of alpha containing 61 per cent. copper, while 15 per cent. will be beta containing 54.5 per cent. copper. With a faster cooling rate diffusion cannot keep apace and the constituents will be cored, the alpha varying from 65 to 61 per cent. copper and the beta from 60 to 54.5 copper. In this case the amount of alpha will be less than 85 per cent. and the beta will be increased correspondingly. The general structure thus obtained is illustrated in Fig. 2. When a more rapid rate of cooling is effected by quenching in water, the alloy is retained largely in the beta form. However, the crystals of beta are usually outlined with dark fringes which at high magnifications are found to be very fine alpha-beta structures almost martensitic in appearance. The separation of this fringe can be greatly suppressed

Jan 1, 1930

By S. G. Lasky

W E seem to have assumed the careless habit in recent years of treating mining geology as synonymous with exploration geology, and exploration synonymous with exploration for new deposits-to be forgetting that mining geology includes also the geologic control or guidance of day-by-day mining operation. In the publicized romantic spotlight of the search for new deposits, we forget the man with the dirty over-alls, grubbing away at the daily tasks of finding new shoots and of helping to keep production up and cost down. During 1949, as in previous years, the resident geologist continued his quiet efficient functioning while the exploration geologist continued to stay in the spotlight-although this time he shared it with what may be called the resource-appraisal geologist. Many broad problems of national import such as tax modification, the operations of the Economic Cooperation Administration, and certain international relations have come up against an unexpected factor lurking in the background, namely, appraisal of world and domestic reserves and latent resources. T. M. Broderick opened the year with his address as retiring president of the Society of Economic Geologists, wherein he analyzed the problems of exploration geology listing among them "the shortcomings of the geologists themselves, of the educators, the mining companies, our Published by permission of the Director, U. S. Geological Survey. technical publications, the Federal Survey and Bureau of Mines, and the property owners."

Jan 1, 1950

By D. H. Yardley

ENGINEERS and geologists find the magnetic compass unreliable in many mineral bearing areas because of local magnetic attraction. This is the case in the vicinity of many contact deposits, and particularly true in the Lake Superior district where iron formation is wide spread and causes wide fluctuations of the magnetic needle. One of the most useful instruments for geologic traversing or running grid and claim lines under these conditions is the dial compass which does not depend upon magnetism. Difficulties encountered in the field because of local attraction can be overcome through transit observation of Polaris or the sun, or use of the solar attachment. However, a field party often lacks the equipment or time for work of such accuracy and it is here that the dial compass finds its use.

Jan 3, 1954

By Augustus J. Bowie

THE discovery of the auriferous cement gravel deposits in and near Deadwood Gulch, Lawrence County, Dakota Territory, in 1876, created a mining excitement, and rush to the Black Hills. Numerous ten and twenty-stamp mills were built on Deadwood Gulch ; Central City and the town of Deadwood sprang into existence, and became the centres of the mining industry of the Hills. Gold quartz deposits were subsequently discovered and located on a so-called mineral belt, extending from Whitewood Creek on the south, to Deadwood Gulch on the north. A northerly group of these quartz locations was purchased in December, 1877, by parties in San Francisco,, who formed a company, incorporated under the name of the Father de Smet Consolidated Gold Mining Company. This company immediately commenced the work of exploration. The deposits were proved to be extensive, and easily mined, but it was found that the ore, on an average, would not. yield more than $10.00 per ton* of 2000 pounds. At this time the cost of supplies and materials in the Hills was high. Miners' wages were $3.50 per diem, and custom mills charged $6:00. per ton. The successful working of mines on "the belt" necessitated cheap milling. The ores being of so low grade,† this could be accomplished only with large and economically running mills. To insure the greatest possible economy, the Father,& Smet mill * Up to December 31st, 1879; the de Smet mine had produced bullion of the value of $718,211.68 from 76,155 tons of ore, being an average value of $9.41 per ton. During the year ending December 31st, 1879, the mine produced 46,344 tons, which yielded $425,360.42, or $9.18 per ton. The total gross cost of working for the corresponding period, including deadwork, exchange, legal expenses, fete., wits $219,914.82. The yield of the mine for the year 1880 (Engineering and Mining Journal, February 5th, 1881), was $600,011, with total expenses of mining and milling, of $313,108. † The first 4083 tons extracted from the de Smet mine, were selected, yielding $62,783.97. The next 25,728 tons produced $230,067.24. The total 29,811 tons were weighed, and worked at custom mills. The yield of the first 409 tons from tine Golden Terra Mine was $11.44 per-ton.

Jan 1, 1882

By AIME AIME

ALFRED WILLIAM GAUGER ??Al" or '?Doc" to his many friends in the coal and chemical industries- is known for his research talents and organizing ability. Appropriately the first public recognition of his technical ability was by the A.I.M.E. in the publishing of a paper by George A. Burrell and Alfred W. Gauger in the "Transactions" for the year 1916. "Al" Gauger was born at St. Paul, July 31, 1892. He graduated in chemistry at the University of Minnesota in 1914. A year later he began his initiation into the mysteries of coal mining when he joined the safety division of the U. S. Bureau of Mines at Pitts- burgh, serving from 1915 to 1917.

Jan 1, 1944