Search Documents

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

Application of technology to the search for new deposits went on apace in 1963. Traditional methods, aided by modern communications, were successful in some out-of-the way corners of the world that had not been adequately prospected, but the co-ordination of several mutually supporting techniques is necessary to define exploration targets in most areas today. Although these obviously include geophysics and geochemistry, which are treated elsewhere in this issue, geology continues to play a major role. As the search focuses on less and less obvious targets there will be more need than ever to "pull out all the stops." Any anomaly may have significance and must be evaluated as a possible lead. Ability to detect them increases as the laboratory workers refine techniques for measuring physical, chemical, and isotopic properties; it will be increasingly the responsibility of the exploration geologist to understand and apply these to economic problems. Simple propecting, the search for outcrops of recognizable ores of traditional types, was perhaps most successful for iron. Potentially large deposits of high-grade magnetite-specularite-hematite ore have been found in the Mary River area near the north end of Baffin Island. The ore holds up four hills that stand some 1500 ft above the surrounding country; obviously they were ripe for discovery by the first person to come across them, in this case Murray Watts, president of British Ungava Explorations, Ltd, As preliminary examination indicates a lump ore averaging 68 to 70% iron, these deposits may be commercial in spite of the unfavorable climate and their isolation from world markets.

Jan 2, 1964

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy's law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950's, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

By Dr. O’Neil Thomas J., Donald W. Gentry

There are mines that make us happy, There are mines that make us blue, There are mines that steal away the tear-drops As the sunbeams steal away the dew. There are mines that have lost the ore chute faulted, When the ore's forever lost to view, But the mines that fill my heart with sunshine, Are the mines that I sold to you. -Anonymous INTRODUCTION The preceding chapters have discussed, in various degrees of detail, the primary considerations necessary to perform a cash flow analysis of a mining-related investment opportunity. Although the previous discussions regarding the manipulations, calculations, and interrelationships of the various components of the pro forma income statement were illustrated in the text, many individuals are un- familiar with the format and appearance of a final spread sheet for the evaluation of a mining property. As a result, it seems appropriate to conclude this book with an abbreviated case study of an actual mine property (currently in production) showing the cash flow analysis and some back-up data. Obviously all of the supporting data and calculations for the case study presented cannot be provided; however, reference is made to the major assumptions utilized and to the appropriate procedures employed in the calculations, as described elsewhere in the text. The problem associated with using any case study for illustrative purposes is that one tends to be overwhelmed by detail. For instance, specific costs, prices, expenditure timings, and other variable values may be challenged because they either do not conform to one's expectations or are not consistent with specific operating experiences. When this occurs the instructional value of the problem becomes obscured. The purpose of most case studies, and particularly the one presented in this chapter, is to expose the student to the methodology, procedure, and format associated with performing a cash flow analysis of a mining property. It is not to laboriously wade through the specific details associated with operating and capital cost development, mine plans, or equipment schedules. It should be noted, how- ever, that the values represented in this case study result from specific mine plans, operating procedures, equipment spreads, manpower requirements, and other en-

Jan 1, 1984

By AIME AIME

THE 139th meeting of the Institute will be held Feb. 17-20, in the Engineering Societies Building, New York. The annual business meeting will be held on Feb. 18 at 10 a. m., and no technical sessions will be scheduled at that time, so that all members may participate in the election of officers, hear the presentation of the annual reports of officers and committees and discuss any matter which they may care to bring up at that time. The annual dinner will be held at the Conlmodore Hotel on the evening of Feb. 20, and the usual good time is promised. Arrangements for this and other social features of the meeting are, as usual, in hands of the New York Sec- tion, of which the chairman this year, Ralph M. Roosevelt, has a well-established reputation earned as president of the Zinc Institute, as host.

Jan 1, 1930

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By H. P. Schwede, H. G. Doll

This paper describes a method to provide identification of particular depths in a borehole through the use of radioactive markers. The correlation of a marker, placed in the wall of a borehole, with known points of the electrical log and with the casing collars in the cased hole permits accurate positioning of tools with respect to a formation, regardless of absolute depth. Such a process is particularly useful in gun perforation of a casing in a well. Technique and equipment are discussed and illustrated. Examples are given of practical application in the field. Introduction During the past decade the search for petroleum has increased the importance of testing zones at depths in wells which have become progressively deeper. The development of new techniques, such as electrical logging, has permitted the identification of producing formations which consist of comparatively thin strata. When thin beds are to be produced at great depths, the problem of positioning tools accurately to place the well in production becomes acute.l Continuous consideration is being given in the petroleum industry towards the improvement of depth measurements in a borehole. The accuracy in absolute depth measurements, whether made in an open or cased hole, whether determined by a cable or a drill pipe, depends upon a number of factors, such as tension, temperature, and calibration. For example, the effects of tension from the weight of 10,000 ft of drill pipe and the thermal expansion of this length . of pipe, where its average temperature has increased SO"', will Produce an elongation as much as 8 ft.2 The effects Of such factors can be minimized through the use of care in depth measurements, the application of corrections based on experience, and continuous calibration or checking. The fact that different methods and different tools are used to determine the depths of formations in wells will sometimes give rise to a difference between measurements. It is evident that an important requirement in a well is the ability to locate at will any subsurface point. While absolute depth measurements have ion in recent years, it is reassuring to have other means to verify, for example, that a casing is perforated at a particular place with reference to a zone within a formation. Such a check on measurements may be had by placing a reference marker at a point known with respect to the electrical log of the borehole. That point is usually chosen to be in proximity to the 'One to be perforated. Thus, only short in depth measurements are made and any inaccuracy becomes very small and of minor importance' The use of reference markers located at fixed points predetermined in each zone where future operations are contemplated enables the operator to position any tool

Jan 1, 1948

By H. G. Doll, H. P. Schwede

This paper describes a method to provide identification of particular depths in a borehole through the use of radioactive markers. The correlation of a marker, placed in the wall of a borehole, with known points of the electrical log and with the casing collars in the cased hole permits accurate positioning of tools with respect to a formation, regardless of absolute depth. Such a process is particularly useful in gun perforation of a casing in a well. Technique and equipment are discussed and illustrated. Examples are given of practical application in the field. Introduction During the past decade the search for petroleum has increased the importance of testing zones at depths in wells which have become progressively deeper. The development of new techniques, such as electrical logging, has permitted the identification of producing formations which consist of comparatively thin strata. When thin beds are to be produced at great depths, the problem of positioning tools accurately to place the well in production becomes acute.l Continuous consideration is being given in the petroleum industry towards the improvement of depth measurements in a borehole. The accuracy in absolute depth measurements, whether made in an open or cased hole, whether determined by a cable or a drill pipe, depends upon a number of factors, such as tension, temperature, and calibration. For example, the effects of tension from the weight of 10,000 ft of drill pipe and the thermal expansion of this length . of pipe, where its average temperature has increased SO"', will Produce an elongation as much as 8 ft.2 The effects Of such factors can be minimized through the use of care in depth measurements, the application of corrections based on experience, and continuous calibration or checking. The fact that different methods and different tools are used to determine the depths of formations in wells will sometimes give rise to a difference between measurements. It is evident that an important requirement in a well is the ability to locate at will any subsurface point. While absolute depth measurements have ion in recent years, it is reassuring to have other means to verify, for example, that a casing is perforated at a particular place with reference to a zone within a formation. Such a check on measurements may be had by placing a reference marker at a point known with respect to the electrical log of the borehole. That point is usually chosen to be in proximity to the 'One to be perforated. Thus, only short in depth measurements are made and any inaccuracy becomes very small and of minor importance' The use of reference markers located at fixed points predetermined in each zone where future operations are contemplated enables the operator to position any tool

Jan 1, 1948

By G. Derge, Ling Yang, John Henderson

Self-diffusion coefficients of aluminum have been measured by the capillary reservoir technique in liquids of the CaO-SiO2-Al2O3 system containirg equimolar portions of CaO and SiO2, in the temperature range 1400o to 1520oC. For the melt containing 6.0 mole pct Al2O3 the results can be expressed by the equation D = [(4.3 * 0.3) x 104] exp [(-85,000 * 17,500)/RT]cm~sec-'; for the melt containing 12.5 mole pct Al2O3, by the equation D = (5.4 i 0.2) exp [(-60,000 * 10,00O)/RT] cm2sec-: A concept of the constitution of these melts has been developed which proposes that the ratios O/(Si +Al) and Al2 O3/CaO determine the dominant species present. In recent years considerable work has been done on the system CaO-SiO2-A12O3 with a view to elucidating the structure of liquids of this system. Conductivity,' electromotive force, 3 density,4 and activity5 measurements have all contributed to an understanding of the problem, but as yet there is no entirely satisfactory theory that can account for all the observed experimental results. In principle, measurements of self-diffusion coefficients should give further information which is not obtainable in other ways. Self-diffusion coefficients for calcium, silicon,6 and oxygen7 have been measured. The present investigation extends the series of self-diffusion coefficient measurements to include aluminum and develops a concept of constitution for liquids of this system which is compatible with all the observed experimental results. EXPERIMENTAL The technique used in the measurement of the self-diffusion coefficient of aluminum was the capillary-reservoir method,8 A126 being incorporated in the melt contained in the capillary and inactive aluminum in the reservoir melt. This method was chosen because it minimizes convection currents' in the diffusion zone. It has the further advantage that the boundary conditions are such that a slight modifica- tion of Anderson and saddington's8 solution of Fick's Law yields an equation which requires measurements only of the length and the initial and final average specific activities of the solidified melt within the capillary. where t is the diffusion time, Co is the average specific activity of the melt contained in the capillary at t = O, C is the average specific activity of the melt contained in the capillary at t = t, 1is the length of the capillary, and D is the self-diffusion coefficient. The equation is of somewhat different form than those previously applied to high temperature diffusion studies because the specific activity of the melt in the reservoir was negligible both before and after diffusion. The diffusion apparatus is shown schematically in Fig. 1. It consisted of a silicon carbide resistance furnace containing the inactive melt in a graphite crucible, internal dimensions 7/8 by 4 in., enclosed in a 1 1/4- by 1 1/2- by 30-in. McDanel tube. A 3/8-in. McDanel thermocouple sheath to which graphite radiation shields and a graphite protection tube were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube the capillaries could be lowered into or raised out of the melt. Temperature was measured with a Pt-Pt 13 pct Rh thermocouple which was calibrated periodically against a standard couple. The furnace temperature was controlled to ± 5°C through the thermocouple immersed in the melt. Temperature variation over the depth of the melt was less than ± 3°C. The inactive melts were prepared from pure native quartz, assaying better than 99.9 pct SiO2, A.R. grade A12O3 and A.R. grade CaCO,. The same quartz and CaCO3 were used in preparing the active melts, the

Jan 1, 1962

By H. A. Doerner

The process for smelting zinc developed several centuries ago is still in use. Through the experience accumulated over this long period of time, details of the process have been perfected until there is little opportunity to make any further improvement except by a radical change in method. Such a change was accomplished by the process recently developed by the New Jersey Zinc Co. The process to be herein discussed is a still more radical departure, which has been developed to large-scale laboratory operation by the Metallurgical Division of the U. 5. Bureau of Minesl. † The reduction of zinc oxide by carbon is a highly endothermic reaction, which requires temperatures in the range 1200° to 1400' C. for even a slow reaction rate. The transfer of the heat of reaction through thick fire-clay walls, the high radiation loss in the type of furnace used, and the practical impossibility of recovering or using the combustible products of the reduction (CO) cause a deplorable waste of fuel. With the one exception mentioned, all zinc smelting is done in small retorts manually charged and discharged. Attempts to mechanize these operations have been only partly successful, and there seems to be no way to avoid or improve the uncomfortable conditions in which the work is done. The reduction of zinc oxide by methane has a relatively high reaction rate at 1000' C. At this temperature most ore residues do not sinter, and it is possible to use metal retorts. These factors make gaseous reduction especially adapted to a continuous operation and compared to reduction by carbon make possible: (1) higher rate of reaction at lower temperature, (2) more nearly complete extraction of the zinc, and (3) much better utilization of fuel and reagent. Although the reaction between methane and zinc oxide requires 105,900 calories per mole, compared to 86,860 cal. in the carbon reduction, it is obvious that much less fuel will be required to supply 105,900 cal. through 36 in. of metal at 1000' C. than to transfer 86,860 cal. through 1 in. of fire clay at 1300° C. Moreover, the gaseous products of gaseous reduction (CO and H2) can supply 183,430 cal. by complete combustion.

Jan 1, 1937

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Fred C. Bond

COMPRESSION TESTS THE standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of crossectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a high-speed steel disk with diamond dust embedded in the edges, and running under a water spray. Such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding planes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing Co., and are listed alphabetically in Table 1. These tests were made on one inch cubes or on diamond-drill cores approximately one inch in diameter and one inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. Compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test No. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TVA quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1946

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

A small group of members of the Institute headed by W. H. Shockley, has insistently demanded that the Institute submit to the members for letter ballot the question of our using in our publications and corre-spondence certain so-called "simplified spellings." The principal argu-ment in favor of this proposal is written by Mr. Shockley and will be submitted in full to the membership for ballot. It rests chiefly on the desirability of saving the time of school children in the learning of the spelling of the English language. A sample of correspondence had with one of the gentlemen on this subject is given herewith in order that members may see what the correspondence and publications of the Institute would look like if we adopted the proposals. This sample was chosen at random: "Onse I condemd the report ov a president of the Institute. He did not pruve his case even on paper-"a hot air profet," I sed. Time has pruved he was." "I rote yu about the muvement to better the spelling in the Institute Bulletin, etc., neglecting to say some things that I mite hav said and things hav happened since which no member ov a democratically governed society shoud stand without protest."

Jan 12, 1919

By C. A. Lemke

THE ores now milled at the Midvale concentrator of the United States Smelting, Refining & Mining Co. come mostly from ;the company's mine in the Bingham district, about 18 miles west of Midvale. Custom ores from this same district and from other western mining districts are also milled at times. The Bingham ores consist of galena, pyrite, chalcopyrite, and sphalerite in a gangue of quartz, quartzite, limestone, and porphyry. The percentage of chalcopyrite is small, usually about 0.5 per cent., while the galena, pyrite, and sphalerite combined constitute about 60 per cent. of the total ore. These three minerals vary considerably' in amount and, at times, all three are somewhat oxidized. The ores also contain gold and silver, the former being mostly in the pyrite while the latter is generally with the galena. The crystallization of the economic minerals varies from fairly coarse to extremely fine. The ores are carried to Midvale by the Bingham & Garfield and the Los Angeles & Salt Lake railroads or by the Denver h Rio Grande Western railroad, in 50-ton, steel, full dump cars. The milling problem is to recover the silver-bearing galena, the gold-bearing pyrite, and the chalcopyrite in a product suitable for the lead smelter and containing the least possible amount of gangue and sphalerite and then recover the sphalerite in a product suitable for a zinc smelter. The minerals are recovered partly by water concentration and partly by water concentration combined with electrostatic treatment.

Jan 9, 1925

By P. D. Hunt, I. Johnson, M. G. Chasanov, H. M. Feder

The solubilities of the transition metals from scundium to nickel, inclusive, in liquid cadmium were determined by sampling saturated solutions. At 400°C these solubilities (ppm) are:Sc, Co, 22; Ni, 12000. Relative partial molal enthalpies and excess partial molal entropies at infinite dilution for the solutes Cr, Mn, Fe, and Co are compared zoitlz similar data for the post-transition metals. Three new intermetallic phases, ScCd,, TiCd, and Ti,Cd, encozaztered in the course of this work, are reported. Measurements of the solubility of the 3-d transition metals in liquid cadmium have been reported' only for iron. The present measurements for the entire series were made as an aid to the study of the systematics of alloy formation. EXPERIMENTAL The apparatus and sampling techniques used for the solubility determinations were similar to those described by Martin etal.' Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple sheathed in recrystallized alumina and immersed in the solution. The thermocouple was recalibrated periodically during the course of the investigation. Thermocouple voltages were measured to the neares 0.01 mv with a Rubicon model 2732 potentiometer. A scaled-down version of the apparratus, in which the total metal charge was about 90 g, was employed to measure the solubility of scandium. Two-mm ID Vycor filter pipets were used to sample the scandium-cadmiurn solutions; the samples weighed about 2g- Cadmium with a minimum purity of 99.95 pct was used; the only impurities detected spectrochem-ically were C'u and Mg, both less than 10 ppm. The purities of the other metals were: scandium, 99.9 pct; titanium. 99.92 pct; vanadium, 99.9 pct; chromium, 99).99 pct; manganese, 99.9+ pct; iron, 99.90 pct; cobalt, 99.95 pct; and nickel, 99.96 pct. Solidified melts were routinely analyzed spectro-graphically. No significant contamination by the crucible, sampling pipets, or other materials of construction was observed. The entire specimen obtained by sampling was dissolved to preclude analytical errors due to segregation on cooling. Colorimetric methods3 were used for the analyses of cobalt (2-nitroso-l-naphthol), manganese (permanganate), nickel (dimethylglyoxime), titanium (peroxide), and vanadium (thiocyanate).4 Chromium, iron, and scandium were neutron-irradiated to produce The dissolved samples were gamma-counted to determine solute concentration.For the separation of intermediate phases from cadmium-rich alloys selective leaching by saturated ammonium nitrate solutions was employed. The concentration of cadmium in the successive leaches was followed polarographically and the process was terminated when the rate of cadmium dissolution decreased markedly. For the further investigation of intermediate phases 1/4- in. diam powder compacts were pressed at 80,000 psi and annealed in argon at 315" to 330°C for 10 days. Larger quantities of alloys were prepared in sealed tantalum capsules heated in a rocking furnace.

Jan 1, 1962

By J. M. W. Mackenzie, C. J. Wood

In attempting to describe the size classification performance of a hydrocyclone, most workers have elected to use either an equilibrium orbit theory or an non-equilibrium orbit theory. The equilibrium orbit theory has been used by the majority of workers including Lilge,' Bradley; and Yoshioka and Hotta. In applying this theory, it is argued that particles in the body of a hydrocyclone attain an equilibrium radial position where the drag force on the particle resulting from the inward radial fluid velocity is balanced by the outward centrifugal force caused by the tangential component of fluid flow. When considered over the full height of the hydrocy-clone, attainment of this radial equilibrium orbit results in the particle following a conical equilibrium envelope. It is then argued that if this envelope lies outside the envelope of "zero vertical velocity," the particle will report to the underflow, while if the equilibrium envelope lies inside the envelope of "zero vertical velocity," the particle will report to the overflow or vortex finder product. The d50-sized particle which reports in equal quantities to the underflow and overflow is assumed to correspond to particles whose equilibrium envelope is coincident with the envelope of "zero vertical velocity." In considering the equilibrium orbit theory, it is apparent that the horizontal position of the particles in the feed inlet pipe should have no effect on their ultimate destination on the hydrocyclone. Each particle should attain an equilibrium position which depends on the density, size, and shape of the particle; the density and viscosity of the fluid; and the flow patterns within the hydrocy-clone. The nonequilibrium orbit or unsteady state theory has been largely developed by Rietema4 and Mizrahi.6 Mizrahi has listed four main objections to the equilibrium orbit theory. These objections center on the short residence time in the hydrocyclone, the fact that the experimental classification curve is much less sharp than is theoretically predicted, and the absence of negative efficiency conditions in hydro cyclones operating on a feed material which is much finer in size than d50. Proponents of the nonequilibrium orbit theory argue that for a particle to discharge with the underflow it must have sufficient outward radial velocity to reach the downward-flowing region close to the hydrocyclone wall in which the flow lines are parallel to the wall and the ratio of vertical to radial velocity is constant. It is then postulated that a d50 particle entering the cyclone at the center of the feed inlet will just reach this downward-flowing region as it reaches the apex. Thus for uniform distribution of particles across the feed inlet, half the d50 particles—that is, those injected in the half of the inlet area nearest the cyclone wall —will report to the underflow while those injected in the other half will not reach the downward-flowing region and will be carried inward to the center of the cyclone and thus report in the overflow. The exact thickness of the down-ward-flowing region of fluid adjacent to the outer wall of the hydrocyclone is uncertain but Mizrahi considers it to be equal to the apex radius minus the air core radius. Particles larger than d50 have a greater outward centrifugal force acting on them than the d50 particles and may reach the wall even if injected at a distance from the wall greater than Di/2 (Di is inlet diameter). Conversely, particles smaller than d50 may not reach the wall even if injected at a distance less than Di/2 from the cyclone wall. Since the equations put forward by the proponents of both theories yield approximately the same values of d50, it is not possible to decide between these theories by measurement of d50. It should be possible however to examine the theories by injecting a small stream of solids into the feed inlet of a hydrocyclone running on clear water. If the efficiency or classification curve is measured for various horizontal injection positions, then the curves should be coincident if the equilibrium orbit theory holds. If, however, the unsteady state theory describes the cyclone operation, then the classification curves should show finer d50 sizes for particles injected close to the cyclone wall. Experimental A 6-in.-diam hydrocyclone with geometry as in Figs. 1 and 2 was used. Quartz particles were injected as a 50% by wt pulp via an 1/8-in. steel probe. For each in-

Jan 1, 1971

Some early production records of the early companies operating in the Deep River field are said to be still in existence, but the writer has been unable to find them. (Table 63.) [ ]

Jan 1, 1942