Search Documents

By J. J. Arps

This paper is a study of the effect of temperature on the electrical resistivity of sodium chloride solutions based on the published resistivity and density data in the International Critical Tables. This temperature effect is of considerable importance in quantitative interpretation of electric logs, where it is frequently necessary to correct mud resistivities measured under surface conditions to temperatures existing at the bottom of the bore hole. An empirical approximation formula was developed for this conversion which has proved to be very useful and seems to provide results well within the range of accuracy of the data involved. This approximation formula states: sistivities of sodium chloride solutions at temperatures of t and t degrees Fahrenheit, respectively. INTRODUCTION Research by various investigators during the past 20 years has clarified the physical principles of the phenomena which cause the natural or spontaneous electric potential in rotary drilled bore holes. The basic relationship which is most commonly used reads: in which the SP deflection, as measured from the shale base line, is expressed in millivolts. K is a constant, which appears to vary between 50 and 110; the low value applying to shaly sands, whereas the higher values are more common in carbonate rocks. A good average value for K = 70. for which value there is considerable theoretical justification." In order to calculate the resistivity of the connate water R and to estimate its "equivalent salinity" (as NaCl) from an electric log by means of this SP relationship from a knowledge of the static self potential and of the resistiv- ity of the mud filtrate R it is necessary to first correct the resistivity of the mud filtrate measured under surface conditions to the resistivity of this same mud filtrate in the well bore at a different temperature. In order to make this temperature conversion for the mud filtrate the variation of the electrical resistivity of sodium chloride solutions with temperature is commonly used. Since some discrepancies were found in the charts ordinarily used for this purpose, it was felt desirable to make a new study of this relationship based on the published measurement data. Because of the fundamental nature of these relationships and as an aid to other workers in this field, an attempt has been made in this study to show every step in the calculations. CONDUCTIVITY VS MOL CONCENTRATION The most complete published reference on the temperature relationship of sodium chloride solutions of different concentrations is provided in the International Critical Tables.' The basic measurement data on the electrical conductivity of aqueous sodium chloride solutions, at different temperatures, as given in these tables, are reproduced in Table 1. The electrical conductivity values in this Table 1 are expressed as 10' times the specific conductivity k in ohm-'cm'l per unit of concentration in milligram mols per liter of solution C, or: RESISTIVITY VS MOL CONCENTRATION These conductivity values from Table 1 were first converted to the corresponding electrical resistivity values (R) , expressed in ohm-meters, as is conven-

Jan 1, 1953

ION exchange is one of hydrometallurgy's new tools, new in application, vet old in principle. Cation exchange between solution and a solid exchanger has been known for more than a century, but ion exchange is still in its infancy for metallurgical use. Still hampered by cost of media, it is faced with much development of actual physical handling. Growing consumption of the rarer metals and need to treat leaner ores are pushing extractive methods ahead. Public concern with stream pollution, or legal requirements, are forcing a clean-up of waste discharge. Industries are finding it vital to make some recovery from heretofore waste material to help pay costs of discharge treatment.

Jan 5, 1953

No. 275. Chemist, assayer, and precipitate smelter, also an experienced shift man; both for a cyanide plant in Peru. Salary £30 Sterling per month; two years' contract and all traveling and living expenses. No. 276. Metallurgist; experienced in reducing tungsten ores and preparing metallic tungsten and tungsten alloys. No. 277. Draftsman and transitman for coal mine work in Middle West. Salary $125 per month. No. 278. Metallurgical engineer familiar with microscopic work and experienced in making microscopic photographs; with some experience in heat treating of alloy steels. No. 279. The Trench Warfare Section of the Ordnance Department desires to get in touch with young men over draft age, or in deferred draft classification, who are physically sound, who can. become candidates for commissions; earning capacity of at least $1700 a year. Must have good character, some business experience, university training, and some technical skill. Application should be made to Captain Hudson Millar, 1800 Virginia Avenue, Washington, D. C,. Three original letters of recommendation from American citizens must be furnished. An appli-

Jan 3, 1918

New equipment for seabed sampling, presently at the prototype stage, operates on the principle of diamond core drilling with wire line core barrels and is designed to drill cores from the seabed at depths down to 200 m with a continuous recovery of cores from an attendant vessel. The machine operates on the seabed by remote control from a console on the vessel. Neither installation nor operation requires the use of divers. Principal Applications Principal areas of application for the drill which is dubbed Maricor include investigation drilling in the continental shelf, mapping geological conditions before large drilling platforms are installed and exploring proposed undersea tunnel routes.

Jan 11, 1973

By Lawrence Addicks

THrough the courtesy of Dr. James Douglas I am permitted to give a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz., during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper CO. A description of the geology of the district will be found in the paper by R. E. Somers published in this volume, p. 604. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent..................... 2.35 S, per cent...................... 3.0 Ag, ounces per ton.............. 0.05 CaO, per cent.................. 0.5 Au............................ None K2O, per cent.................... 4.0 Fe, per cent..................... 1.50 SiO², per cent.................... 70.0 Alz²O³, per cent....................13.OO The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total reeovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable. Concentrating experiments already available indicated that the tail-

Jan 1, 1916

By J. J. Tietjen, D. Richman

Single-crystal Gap lms been epitaxially grow from the vapor phase at a rate oJ 3 p per nzin without encountering a7Zy low-ang-le grain boundaries or debwading- the electrical properties of the material. This growth rate exceeds any value previol~sly reported for the vapor phase growth of Gap. In pure material, mObilities ns high as 175 sq cm per U-sec at room tenzperature and 1450 sq cm per v-sec at 77°K have been obtained. These values are anLong the highest that have been attai)led for this material. For the first time, Gap possesses a number of important properties which make it well-suited for use in electro-optic modulators. First, the transverse electro-optic effect is operable in this material, which makes it possible to increase the path length of the modulated iron doping of Gap has been achieved; this results i?z resistivities of approximately 10" ohm-cm. The problelrls of residual strain and isolated shorting paths in these crystals have been partially solved. Electro-optic modulation of visible radiation has been demonstrated with this material. It is anticipated that further improvement with regard to the probleins of strain and shorting paths will result in a practical Gap electro-optic modulator. radiation without increasing the applied voltage. In addition, this permits the use of thin crystals so that relatively small voltages are needed to provide the requisite high electric fields. Second, GaP is a cubic crystal and therefore does not introduce critical optical-alignment problems associated with birefrin-gent crystals, such as ammonium dihydrogen phosphate (ADP), and potassium dihydrogen phosphate

Jan 1, 1968

By W. Spencer Hutchinson

It is the purpose of this paper to describe a method used to determine the corundum contents of samples of hard crystalline gneiss containing both corundum and red garnet. A chemical analysis of the rock for alumina would not fix the amount of corundum became at least three other constituent minerals of the rock, mica, feldspar, and garnet, contain alumina combined with silica. Following are the principal minerals found in the samples, together with their specific gravity and hardness as given by Dana: The corundum occurred in crystals of a gray or bluish gray color, in minute grains and coarser up to 0.5 in., and no massive or block corundum was observed. The larger crystals were commonly quite slender, well defined, and the normal hexagonal form clearly developed. They lay with the structural planes of the gneiss, and sometimes appeared prominently in relief on weathered surfaces. In some cases these crystals had suffered partial or total alteration to mica, margarite, or other soft minerals, a condition illustrated by sample D, which appeared to be studded abundantly with corundum on the flat faces. Garnet, a striking feature of nearly all the samples, was present in small rounded crystals of a pink to red color. The samples were first broken to pass a No. 4 mesh screen. This was done with a hammer on an iron plate, particular care being taken to avoid the breaking of the crystals finer than need be to pass the screen. A portion of the sample weighing 500 g. was then taken and, with a little water added, was scoured round and round in an iron bucket with a wooden block, until the coarse crystals of corundum were cleaned of adhering pieces of mica. The bucket was then re-

Jan 1, 1914

By G. Thomas, O. Johari

MEIERAN and Richman' have proposed a method for the determination of electron-diffraction patterns from twinned bcc crystals. It is the purpose of this note to present a general method capable of predicting the positions of all reflections from both matrix and twin regions for all possible orientations of cubic crystals. The method has been verified for twinning in explosively deformed copper, and is found to be a very useful tool when used in conjunction with stereographic projection, and dark-field electron microscopy. Let an isometric crystal be twinned in any (hkl) plane. The twinning can be considered either as a reflection in the twin plane or as a 180-deg rotation about the twin axis. In reciprocal space, the 180-deg rotation about the twin axis would place a given point p, q, Y to a new position P, Q,R, such that both will be equally inclined to the twin axis. This is represented in Fig. 1. If the coordinates of three such pairs of points are determined, the matrix of the transformation can be obtained.' It is also seen that such pairs would satisfy another condition, i.e., the vector [p,q,r] plus the vector [P,Q,R] will yield a multiple of hkl, i.e., the indices of the twin plane, because in isometric systems the axis [hkl] is perpendicular to the plane (hkl). This can be simplified by taking the points along the three axes. If a point h2 + k2 + 12, 0, 0 is taken along the x axis, it is seen that its new indices should be so as to yield a sum 2h2, 2hk, 2hl,i.e., 2h(h,k,1). (Also the points h2 - k2 - 12, 2hk, 2h1, and h2 + k2 + 12, 0, 0 are equidistant from the origin and both points make equal angles with the twin axis, i.e., cos-' h/dh2 + k2 + l2.) Similar operations for the points yield respectively, after the 180-deg rotation about the twin axis. Following the method due to Buerger,' the matrix of the transformation is obtained as follows: Using this matrix the indices of any other point in reciprocal space can be determined. This matrix is much simplified for (111) twinning commonly encountered in fcc metals, since are each equal to —1; hence

Jan 1, 1964

By Alphonse C. Van Besien, Arcy A., L. T. Larson, D&apos Shock, J. W. Peters, Ted H. Eyde, Dermot Ross-Brown, David L. Campbell, W. W. Dudley, John P. Bunch

Over the last several years, unfavorable economic and political pressures on open-pit mining have placed the industry in a generally defensive position. As a consequence, there have been changes in the traditional organizational and production methods to increase operating efficiency. For example, staff groups that were once used almost exclusively for production support are now being organized as mining/environmental specialists. These specialized groups are responsible for obtaining mining permits and insuring compliance with existing permit requirements. Permit issurance and renewal continues to grow as a major budget item in open-pit operations.

Jan 2, 1977

By C. D. Allman

Specifications for coal at the Grand Lake thermal electric station read in part: "Coal will be Rom Minto Bituminous (strip operation). Maximum lump 3x3x4 ft. Very corrosive, abrasive and when damp, sticky. Coal may consist of frozen lumps of coal, snow and ice." To maintain quality control it was necessary to develop an automatic sampling system capable of: 1) sampling from one 10-ton truckload every 1½ min; 2) permitting an operator to automatically take a sample from each truckload; 3) depositing the sample in a pre-selected container, one of a possible 10; and 4) performing the sampling operations in accordance with latest ASTM specifications for sampling coal with an ash content of 35%. This paper tells how these and other problems were resolved and describes the equipment used. The New Brunswick Electric Power Commission issued detailed specification No. 5351-5009 outlining the scope of work and general requirements for a mechanical coal handling system to be installed at the Commissions Grand Lake Generating Station. The thermal station is located at Newcastle Creek, some 40 miles east of Fredericton, N.B. Canada, on the shore of Grand Lake. This particular location is immediately adjacent to the Minto strip mining coal area of New Brunswick. Contained in the specifications, but not detailed specifically was an automatic coal sampling system. The system outlined, was to be designed and specified by the individual equipment tenderers. In conjunction with the Hardinge Co., the Barber-Greene Co. designed a sampling system which was contained in the general contract proposal. The system as designed originally, however, presented certain limitations to a continuous coal handling system and was ultimately changed. However, it was only through preliminary study and design that problems created by the specifications were determined, and these problems discussed and finally negotiated with the NBEPC engineering staff created the subsequent sampling system now being installed by Barber-Greene. It must be considered that where the original specifications did not detail the mechanical equipment, it was necessary to present a system which would correspond to the intent of specification and for which Barber-Greene would be responsible as to function, but remain in a competitive position with regard to the tender considered primarily on a price basis. The system now being installed, contains basically all the components which were detailed originally, with the exception of the holding bin arrangement, which was changed to allow a continuous operation of the entire coal handling system. SPECIFICATIONS The specifications covering the sampling system follow. 4.5 Sampler: An automatic sampling system shall be installed capable of sampling one-truck load of coal every 1½ min. When the coal is dumped into the receiving hopper, the operator shall push a button and the sampler shall automatically take a sample of that particular coal when it reaches the sampler. Then the sample taken shall be crushed and reduced in quantity to a workable sample and deposited in a pre-selected container, one of a possible ten. All samples and sampling operations shall be in accordance with the latest edition of ASTM designation 492 for sampling coal with an ash content of 35%. The coal for the initial sample shall have maximum sized lumps of about 3/4 in. and the final sample shall be adjustable from 2 to 5 lb per sample and capable of passing through a sieve with 1/8-in. diam openings. It should be noted that, because of the time delay between the time the sample is requested and when it is actually taken, the operator may call for one or two additional samples from different coal before the first sample is completely refined and in the final sample can. Coal is received from a number of different suppliers on the same day, therefore, the system shall be designed so that there is no possibility of mixing or contaminating the coal from the different suppliers. All coal rejected from the sample shall be returned to the main conveyor. All chutes, hoppers, etc. shall be designed in accordance with Section 4.6 of these specifications. 4.6 Chutes, Hoppers, etc. All chutes and hoppers

Jan 1, 1963

By E. L. Dougherty

A phenomenological theory for a one-dimensional unstable miscible displacement similar in type to the Buckley-Leverett model but including the effects of mixing is proposed An equation giving the fractional flow of pure solvent through an oil phase containing dissolved solvent is derived including the effects of gravity and nonbomogeneities. Numer ical integration of the resulting pair of nonlinear hyperbolic partial differential equations gives volumes of dissolved and undissolved solvent as functions of space and time. Parameters in the model which characterize mixing due to dispersion were determined from experimental data; the parmeters correlated with viscosity ratio. The results indicate that the rate of dispersive mixing is proportional to volumetric flow rate Incorporated into our equations were Koval's heterogeneity factor H. which characterizes mixing due to channeling. This allowed satisfactory predictions of displacement behavior observed in horizontal floods in nonhomo-geneous cores; but in most cases the values of H which we used were considerably larger than those used by Koval. INTRODUCTION It has been shownl,2,3 that for favorable viscosity ratios, the diffusion equation with convection satisfactorily describes the behavior of a miscible displacement in a porous media. Numerous attempts to develop a satisfactory mathematical description for the case of unfavorable viscosity ratio have been reported, but they have met with only partial success. These attempts, which are reviewed by oval! have taken two approaches: (1) development of a flow model akin to the Buckley-Leverett approach for immiscible displacement neglecting the effects of mixing5,6 and (2) simultaneous application of Darcy's Law for flow and the diffusion equation with a convection term for mass transfer.7,8,9 We set out to construct a mathematical model of Type 1 including, though, the effects of mixing. Based upon a set of hypotheses, we derived a pair of nonlinear hyperbolic partial differential equations which describe in a one-dimensional system the combined effects of flow and mixing. To work with these equations it was necessary to develop a fractional flow formula. The combined system was integrated numerically using the method of characteristics. In our equations the mixing process is characterized by four parameters. Three of these, labeled ß, P1 and P2, account for dispersive type mixing. The fourth is the heterogeneity factor H, proposed by Koval to account for channeling due to nonhomogeneities in the porous media. Values of the parameters which would cause agreement between theory and experiment were determined by trial-and-error for miscible floods conducted in horizontal cores of both homogeneous and heterogeneous materials. Calculations were also performed for vertical floods in homogeneous cores. The purpose of this paper is (1) to present the details of the mathematical analysis, (2) to present the results of the calculations, (3) to consider what light the results shed on the mixing process in an unstable miscible displacement, and (4) to provide a firmer foundation for the correlation technique developed by Koval for predicting the behavior of unstable miscible floods. STATEMENT OF PROBLEM The problem is to construct a mathematical model which describes in one dimension the observed behavior in an unstable miscible displacement. The approach is phenomenological in that the equations are based on assumptions which violate certain physical precepts known to apply to the displacement phenomenon. However, the assumptions do allow us to account mathematically for the more essential phenomena. The work is of value if we can quantitatively predict experimental results which heretofore could not be predicted, even though the synthetic nature of the model belies complete explanation of the observations. We assume that the system is comprised of two contiguous flowing phases. One phase, which we call free solvent, has the properties of pure solvent. We call the fraction of the pore volume occupied by this phase the solvent saturation, designated s. The oil phase consists of oil containing dissolved

By F. S. Sinnatt

THIS paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to playa definite part in the spontaneous combustion of coal in the goaf (waste).

Jan 3, 1925

By G. Knight

In most mines the major contribution to the dust exposure of miners arises from rock hand- ling. Scooptrams are frequently used and produce 8 to 1300 mg of respirable dust for each ton of ore loaded. It is shown that sprays at drawpoints are not fully effective in wetting the rock and suggestions for improved wetting techniques are given. Techniques for improved dust control by ventilation and local filtration are described. The problem of dust from ore- passes and dumps on tramming levels are outlined.

Jan 1, 1981

By H. G. Doll

A new electrical logging method. called MicroLaterology is described. whereby the resistivity R of the invaded zone close to the wall of the bore hole is measured. This method essentially utilizes a system of concentric circular electrodes iml,edded in an insulating support which is applied to the wall of the hole. A beam of current of very small diameter is focused horizontally into the formations by means of an automatic control device. and then opens widely at short distance from the wall. with this method, R most often can be recorded directly. except when the mud cake is very thick. in which case a correction is easily provided. The basic role of factor R in the quantitative analysis of electrical logs in terms of fluid saturation and of porosity is explained. The paper is illustrated with field examples. INTRODUCTION In electrical logging. the resistivity of that part of the penneable and porous formations which is invaded by mud filtrate is an important factor in the interpretation. Measurements made with the conventional devices — normal. lateral — and also with improved systems as the Laterolog and induction logging' — are very often more or less affected by the presence of the invaded zone. and the knowledge of the resistivity of this zone is useful in the evaluation of the true resistivity of the beds. which itself is a basic element for the determination of fluid saturation. Moreover. the comparison of the resistivity of the invaded zone with the resistivity of the mud filtrate gives valuable indications on the magnitude of the formation resistivity factor — which in turn is necessary for the quantitative interpretation of the logs. both in terms of fluid saturation and of porosity. On the other hand. it is generally admitted that the invaded zone is not a homogeneous medium separated from the uncon-tamirlated part of the bed hy a well defined cylindrical boundary. but that the fluid distribution—filtrate. connate water. hydrocarbon — and hence. the resistivity. in the invaded zone varies progressively with the distance from the wall of the hole. The term "resistivity of the invaded zone" therefore corre-sponds to an average value which is a function of the distribution of the fluids Inasmuch as the law of this distribution is not exactly known, the resistivity of the invaded zone is not a well defined factor. A much better definition is obtained if the medium under consideration is limited to that part of the formation which is within a short distance from the wall of the hole. It seems likely a within a distance of at least two or three in., most of the fluids in in the pores of tile formation have been displaced by the mud filtrate. The connate water has almost certainly been flushed out. and the oil. if any has generally been reduced to a comparatively small amount. The resistivity witliir~ the radial limit of two to three in. is. therefore. prac.tically constant at an). given level: its value. at least when the proportion of conductive solids in the formation is negligible. is chiefly dependent on the resistivity of the filtrate and on the porosity of the formation, and is affected only to a relatively small degree by the presence of the small amount of residual oil. This part of the formation close to the wall of the hole will he designated in the following as the "flushed zone." a-distinguished from the more general term of "invaded zone'. which relates to the part of the formation extending from the wall out to the distance where the formation is completely uncontaminated. The symbol R,, will he used for the resistivity of the flushed zone. (The notation R is related to the radial distance from the hole. If x designates this distance. xo is the initial value of x, i.e., the value corresponding to the region very close to the wall.) The determination of R is difficult, if not impossible. from logs made with the conventional devices. The long normal and the long lateral are. of course. not suited for this purpose because their radii of investigation are by far too large. The short normal. and the limestone sonde—-after correction for the effect of the hole hole — give resistivity values which corre. spond to materials situated within a comparatively short distance from the hole, but this distance is still several time. as great as the thickness of tire flushed zone. The only value which can be obtained with these devices corresponds to an average resistivity of the invaded zone- — and this only provided the invasion is deep enough, since otherwise the meas "red values would also be affected by the uncontaminated region beyond the invaded zone. It should nevertheless be recalled that despite these limitations. the measurements given by the short normal and or the limestone sonde are always very useful for qualitative interpretation. and also in favorable cases for the qantitative analysis of the logs in terms of saturation and porosity. The MicroLog. which was primarily developed for the detection of permeable beds and for an accurate determination of their boundaries. provides a good approach towards the evaluation of R. In the case of hard formation.. however. The

Jan 1, 1953

By George F. Weaton

Mining differs from the ordinary industry in that most industries and enterprises have an indeterminate life, apparently perpetual, and therefore, are not called on to replace the original investment. In mining, however, when the ore bodies are mined out, there is nothing left, The original capital investment must, therefore, be returned to the investor by the time that the profitable life of the mine is ended. When the operating company makes no provisions for perpetuating its life by investing a portion of its earnings in other properties, the usual procedure is to pay the investor, periodically, a dividend sufficiently larger than the risk return on his investment to enable him, if he reinvests this overplus at a safe rate of compound interest, to replace his original capital by the time the mine is exhausted. This overplus constitutes a return of invested capital. In estimating the value of a mining enterprise, the work leading to the final result may be divided into two parts. The first is the examination of the property to determine ore reserves, mining costs and profits, financial requirements and future prospects. Whatever conclusions are reached in this phase of the work depend on the experience, thoroughness and integrity of the examining engineers. The second is the calculations pursuant to the field examination.

Jan 5, 1973

By Shun-ichi Satoh

In the previous paper, the writer indicated that the arc welding of cast iron is practicable only when barium carbonate is used to retard the fusion of electrodes. Later, he tested the effects of 48 other elements, to discover the cause of their retarding action. Wrought-iron bars 33 cm. long and 0.53 cm. dia. were used as electrodes. The chemical analysis of the original electrode is given in Table 1. Table 1.—Analysis of Electrode Per Cent. Carbon.................................................. 0.045 Silicon................................................... 0.028 Manganese....................................... Trace Phosphorus.............................................. 0.047 Sulfur................................................... 0.008 Each of the bars was wound with a twine of asbestos (1 mm. dia., weighing 0.5 g.) and then was coated with a mixture of equal quantities of graphite and carborundum and one of the compounds listed in the second column of Table 2. The method used in coating was as follows: The mixtures were reduced to paste by adding to them a solution of water glass (1:3); they were next put in a glass tube of 8 mm. inner diameter, with funnel-shaped mouth (the same tube shown in the previous paper); then the bars were passed through the tube so that the mixtures were coated on them. The glass tube was used only as a means of making the diameters of all coated bars exactly 8 millimeters. The cast iron was deposited on the steel plates by connecting the electrodes first to the positive and then to the negative pole of the generator. The figures representing the time, voltage, amperes and energy required to melt each electrode are given in Table 2. They are arranged in the order of the atomic weights of the elements contained in the coatings. In Figs. 1 to 4, which show respectively the time, current, voltage and energy required in this operation, the abscissas indicate the atomic weights of the elements contained in the coatings, and the ordinates

Jan 1, 1929

By A. K. Chakravarti, A. Lihiri, G. G. Sarkar

One primary objective of India's third Five Year Plan is the expansion of coal production. The goal: boost present output of 45 million tons to 95 million tons by 1965--an increase of more than 100 pct!

Jan 7, 1961

By Leonard Logan

The petroleum industry is not peculiar in that it has a problem of stabilization. Economic conditions, not only in the United States but throughout the entire world, are unstable. However, the petroleum industry together with coal mining and agriculture has experienced a longer period of depression than most of the others. It is significant to note that industries engaged in the production of basic raw materials, the primary industries, have not enjoyed as much prosperity since the war as the secondary industries, or those engaged in the fabricating of raw materials and their distribution. The problems of the primary industries are not all the same. Overproduction has existed for several years in agriculture but its causes are not the same as those that have brought about overproduction in the petroleum industry. Unlike agriculture, the institution of property rights and the migratory nature of oil are responsible for the oil man's troubles. Our laws permit the owner of the oil and gas rights, with certain exceptions, to drill when and where he pleases. Since oil is migratory, the adjacent property owner must go and do likewise—drill. This condition spread over a wide area soon brings to the surface more petroleum than can be readily absorbed by the market, creating a condition of overproduction. It is significant to note at this place that when overproduction occurs the complete units in the industry suffer least. A complete unit is taken here to mean a corporation engaged in all the phases of the industry through production, transportation, refining and marketing. In the present depression the complete units in the industry are not in as bad financial condition as those engaged in single phases of the industry. The same thing can be said of the zinc industry, the lumber industry, and the other industries where there are organizations engaged in all the steps through the production of raw materials to the marketing of the finished product. The reason for this is that the complete units are in better position to coordinate all the factors that would work for a stabilized condition than are the units that are engaged in a single branch of the industry.

Jan 1, 1931

By H. H. Pentz

This paper gives the derivation of a practical formula for the calculation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 260 ft. per 1000. Derivation In Fig. 1, o represents the image of the shot point a. Then the length of the path acb is equal to ob and ae'd is equal to od. In the triangle aob, p is equal to ob, x is equal to , and c is equal to ao. The angle u is the apparent dip of the reflecting horizon. Angle oab is equal to (90" - u). The quantity m is the slope of a line tangent to the curve, defined by equation 1, at the point (p, x). The quantity m' is the slope of the line tangent to the curve at the point (p', 2').

Jan 1, 1940

By H. H. Pentz

This paper gives the derivation of a practical formula for the calculation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 260 ft. per 1000. Derivation In Fig. 1, o represents the image of the shot point a. Then the length of the path acb is equal to ob and ae'd is equal to od. In the triangle aob, p is equal to ob, x is equal to , and c is equal to ao. The angle u is the apparent dip of the reflecting horizon. Angle oab is equal to (90" - u). The quantity m is the slope of a line tangent to the curve, defined by equation 1, at the point (p, x). The quantity m' is the slope of the line tangent to the curve at the point (p', 2').

Jan 1, 1940