Search Documents

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

By John A. Graves

Anaconda's Jackpile-Paguate mine, located between Albuquerque and Grants, N.M., is situated at an elevation of 6000 ft in a semi-arid desert region. The original Jackpile deposit was discovered by Anaconda air and ground exploration parties in Nov. 1951. A large percentage of the uranium mined in New Mexico comes from the Jackpile-Paguate, which is one of, if not the largest, open pit uranium mines in the world. From 1953 to the present, 120 million tons of overburden, mining waste, and low-grade material have been removed to produce approximately 10 million tons of merchantable uranium ore, having an average grade of about 0.25% uranium oxide. Identifying the Orebody Surface drill holes delineate the ore bodies on a predetermined grid which varies in dimension but usually affords 100-ft control. These holes are probed immediately after drilling by geophysical logging trucks, resulting in a gamma log and digital readout from each hole. From this information it is possible to arrive at an almost immediate conversion to percentage of U3O8 on 6-in. intervals. Initially a hole is probed at a reconnaissance speed of 10 fpm with a time constant of 8 sec. Wherever the gamma recording goes off scale on an initial run, that particular zone is rerun at 2 fpm and at a time constant of 2 sec. This time constant is the interval that emissions are counted and accumulated for recording purposes. The search radius of the Geiger probe is approximately 18 in.

Jan 8, 1974

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,'~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro'~ suggested that the strain E can be deduced

Jan 1, 1970

By F. X. Tartaron

This article is a continuation of a previous paper by the writer in which Kick's Law was stated to be a part of comminution theory. ln the present paper, a broadening of ideas is attempted in order to state a general theory. The word "general" is employed because the new theory includes all previous laws and generalizations which are considered to be essentially correct. These ideas are combined into a coherent whole and the general theory can be expressed by the equation In the author's previous paper on comminution, ' the equations developed were based on Charles' equation of exponents a-n +1 = 0. 2 This paper is divided into two parts, designated as First Approach and Second Approach. In the First Approach, the equations of the previous paper are utilized, with Charles' equation of exponents being necessary. In the Second Approach, a separate and independent method is used to derive the same conclusions as in the First Approach, but without the use of Charles' equation of exponents. Holmes accepts the theoretical foundation of Kick's Law as sound but denies that the law as such operates in comminution. His idea is that Kick's Law requires homogenous matter whereas the presence of cracks, flaws and cleavage planes, which predominate in the coarser particles, makes matter unhomogene-ous. This explains why there is no experimental evidence to support Kick's Law. However, since the basis of the law is theoretically sound, all experimental evidence must be viewed as emanating from it. This requires modification of current comminution equations to fit this concept. Holmes makes the modification by changing the constant exponent n in the general energy equation used by Charles (E = - JCdx/xn) to a variable exponent r. The writer asserts that Kick's Law operates in comminution without modification but it does not

Jan 1, 1963

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By Henry Hibbard

AT THE beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as .it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By Edward Perry

IN the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.1 Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve.

Jan 2, 1916

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

By Julian Kennedy Edgar

THINKING that it may prove of interest to the Institute, I have prepared a short account of the blowing in and subsequent working of the "A" furnace of the Edgar Thomson Steel Works. This furnace was built for the purpose of making spiegel, but has been started and is now running on Bessemer iron. The shape and size of the furnace are shown in the accompanying drawing. It will be seen that the section is formed of lines making very small angles with each other. In fact, an arc of a circle can be drawn, from the top to the tuyeres, which will nowhere deviate more than two inches from the lines given. In building, also, great pains were taken to gradually round the angles, so that the most careful observer, standing in the crucible and looking upward, could not tell at what points the slopes changed. It will also be seen that the widest part of the furnace is almost exactly midway between the bottom and the stock line, The flattest slope is maintained for 20 feet above the crucible, and is about 1 s inch to the foot from the perpendicular. The furnace is lined with small brick throughout, and has six tuyeres four inches in diameter, which project seven inches inside of crucible. There are three Siemens-Cowper-Cochrane stoves, each 15 feet in diameter by 50 feet high. Blast is furnished by an upright engine with 32-inch steam cylinder, 84-inch air cylinder, and 48-inch stroke. The steam cylinder has balanced poppet valves, working horizontally. The steam valves are worked by a Porter link-movement in order to obtain a variable cut-off. The exhaust valves are worked by a separate eccentric. It is intended to attach a governor to the cut-off, but at present it is set by hand. The steam cylinder is

Jan 1, 1880

By Julian Kennedy

THINKING that it may prove of interest to the Institute, 1 have prepared a short; account of the blowing in and subsequent working of the "A" furnace of the Edgar Thomson Steel Works. This furnace was built for the purpose of making spiegel, but has been started and is now running on Bessemer iron. The shape and size of the furnace are shown in the accompanying drawing. It will be seen that the section is formed of lines making very small angles with each other. In fact, an arc of a circle can be drawn, from the top to the tuyeres, which will nowhere deviate more than two inches from the lines given. In building, also, great pains were taken to gradually round the angles, so that the most careful observer, standing in the crucible and looking upward, could not tell at what points the slopes changed. It will also be seen that the widest part of the furnace is almost exactly midway between the bottom and the stock line. The flattest slope is maintained for 20 feet above the crucible, and is about 18 inch to the foot from the perpendicular. The furnace is lined with small brick throughout, and has six tuyeres four inches in diameter, which project seven inches inside of crucible. There are three Siemens-Cowper-Cochrane stoves, each 15 feet in diameter by 50 feet high. Blast is furnished by an upright engine with 32-inch steam cylinder, 84-inch air cylinder, and 48-inch stroke. The steam cylinder has balanced poppet valves, working horizontally. The steam valves are worked by a Porter link-movement in order to obtain a variable cut-off. The exhaust valves are worked by a separate eccentric. It is intended to attach a governor to the cut-off, but at present it is set by hand. The steam cylinder is

Jan 1, 1880

By Gordon S. Duncan

The U. S. Geological Survey, I believe, has almost completed a study of the Harney Peak quadrangle, preliminary to the publication of a report on that district. As I was engaged for some months on an investigation of the mode of occurrence of the ore-bearing formation in this area, it has seemed to me timely to make public the results of my study, as a contribution to the consideration of this subject. It seems scarcely necessary to describe the locality and general geology of the Black hills of South Dakota, for since 1846 many have contributed information concerning this region, some of the reports bearing such well-known names as those of Walter P. Jenney, Henry Newton, S. F. Emmons, and C. R. Van Hise, while me have only to glance at Bulletin No. 4 of the South Dakota School of Mines, in which Prof. C. C. O'Harra, of that institution, has given us a bibliography of contributions to the geography and geology of the section, to find that other well-known men have studied the district, and have given us the benefit of their researches. The U. S. Geological Survey has made geological maps of nearly the whole of the Black hills, the only quadrangle yet to be conlpleted being, as stated, the Harney Peak district. During the late summer and autumn of 1910, it was my lot to examine and report on a considerable area in this neighborhood, which once had been prospected, and in some cases exploited, for tin. This paper gives an account of certain geological phenomena, noted at that time, which greatly influenced my conclusions. The predominating formation of the district is pre-Cambrian, represented by a highly-cleaved mica-schist, usually very gar-netiferous, and sometimes hornblendic. Rising like an island from the surrounding schist is a large mass of granite, known as

Jan 1, 1913

By Paul H. Rydlund

Substantial priming was a considered necessity for proper initiation of ammonium nitrate-fuel oil mixes as ANFO began to carve its niche in the mining industry in the latter fifties. Heavy priming accompanied the introduction of prills and oil to many blasting operations, large charges of high explosives were commonly used at the bottom, top and frequent intervals throughout the column. As the quality of ammonium nitrate improved and operators became more experienced, primer costs began to diminish. Increased experimentation continued with reduced primer costs a main objective. Cast primers were introduced and became accepted as an excellent companion for ANFO. Although the trend toward larger diameter boreholes became increasingly popular, emphasis on lower and lower priming costs continued. A primer was simply required to produce any type of initiation within the ANFO column to be considered adequate. Suddenly ANFO priming had digressed from excessive to marginal. Early experimental data from test site and laboratory indicated that ANFO had a tendency to react inefficiently in the initiation region of the column unless substantially primed. This was evidenced by the presence of unstable reaction rates detected with newly developed detonation velocity measuring equipment. These low order or "transient" velocities were believed to originate because of inadequate primer strength or a primer diameter to column diameter mismatch. However, the nature of this experimental work was generally confined to small diameter column charges detonated in iron pipe simulated bore-holes. It was questionable whether the smaller scale laboratory data was applicable to large 12 1/4 and 15-in. boreholes.

Jan 3, 1973

By F. G. Tryon, F. E. Berquist

Our task is to make a prospecting trip over the whole field of mineral economics which other lectures of this series will explore in detail. The old timers who really understand mining warn us that its economic aspects are often neglected, and this we find to be true. We shall try to show that mineral economics deserves recognition as a separate branch of economic science with urgent and distinctive problems of its own; that to cultivate it requires a fusing of the viewpoint of economics with that of geology and engineering; and that the help of both economists and technical men is needed in exploring its problems and in training workers in the field. To save time, we shall pass over the familiar subjects of production, consumption, and distribution which bulk as large in the market analysis of the minerals as they do in other commodities. The existence of these problems may be taken for granted and attention centered rather upon those that differentiate mining from other branches of industry. What then is the case for an economics of minerals? Why set up a new compartment in a branch of knowledge that is already well subdivided? Do not the established principles of economic theory apply here as elsewhere? In pleading for recognition of mineral economics one often finds that

Jan 1, 1932

By Su Zhen

Based on the technical features of the Feng- huang-shan concentrator, the authors have designed a new scheme for optimal search and self-adaptive control in flotation process, in order to apply computer control to the concentrator. Hence, a plant test of optimal control in bulk flotation of copper and iron sulfides was successfully carried out. The control parameters are xanthate addition, pulp level, and amount of aeration, etc., in flotation cells. Two mathematical models of multiple parameters established by the authors were adapted and flotation efficiency was used as an objective function in the control.

Jan 1, 1984

ALL that I have been able to tell you concerning the ordinary practice of parting with aqua fords I have striven to demonstrate to you as briefly as possible. Now, before passing on to speak of other things, I wish to teach you the method that you must follow in order to recover whatever is good in those chalky precipitates of that acid and all the silver that you put in; it was for this reason that I told you to save them in a cucurbit by themselves. This is called "water of whites" by the master parters, and in reality is nothing other than the precipitates of thick phlegm of aqua fords, white as chalk. If these were not extracted from the acid, the spirits of the infused materials [69] would be almost without

Jan 1, 1942

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

THE beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than 90 per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as originally proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accumulated since then, showing the utility

Jan 1, 1945

By John Ward Smith

Dawsonite-bearing oil shale of Colorado's Green River formation offers a unique and vast (more than 5.9 Gt of A120 j) resource of easily extractable alumina. The processing methods required by the thermal reactions of dawsonite and its oil-shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary federal oil-shale withdrawal appear less solvable.

Jan 1, 1982

By Arthur C. Simmons

In common with all other producing areas of the United States, Pennsylvania enjoyed increased activity and prosperity during 1937 (Table I). Prices of crude oil were better than for any year since 1930, and the Bradford average was $2.599, compared with an average price of $2.60 in 1930. Production and drilling activities were increased over 1936, although drilling for oil represented almost entirely a program of secondary development in both the water-flood areas and the air-gas repressuring areas. Bradford Oil Field The Bradford oil field continued to produce the major portion of Pennsylvania oil; however, no changes occurred in oil-production methods during 1937. Practically all of the production in the Bradford field is by water-flooding and the total number of oil and water wells completed within the area increased from 3205 in 1936 to 4112 in 1937; an increase of approximately one-third over 1936 completions. The percentage of water wells is approximately one-half of the total completions, although any specific five-spot development will have a proportion of 55 to 60 per cent water wells and 40 to 45 per cent oil wells. Offsetti~ig and boundary oil wells probably will result in a division or percentage of 50 per cent oil and 50 per cent water wells. The quoted figures for well completions include the entire Bradford field, approximately 12 per cent of which is in Cattaraugus County, New York. It is possible to make a segregation of production, but it is not possible to segregate well completions. Production in the Pennsylvania end of the Bradford field in 1937 totaled 15,076,000 bbl., or a daily average of 41,300 bbl. compared with a daily average of 37,000 hbl. in 1936.

Jan 1, 1938

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

HAVING told you of the practices of the arts involving other metals, I wish to tell you also of the practice of that of tin.* Indeed, since this is an easily melted metal, in common use for the utensils which are made for human needs, it is an art known not only to skilled men but also almost to children, wherefore I could proceed with- out telling of it. However, besides the production of plates and bowls and many other dishes for eating from and keeping things in, this embraces two other arts, both of which you should know about because they are useful and beautifid. One of these is the art .of making the letters with which books are printed, and the other is that of making the sheets from which organ pipes are built. The vessels, as perhaps you have seen, are cast one by one in moulds made of white tuff. Several pieces fastened together are then put on the iron axle of a wheel rotated by hand, and [138v] they are turned with a slightly bent tool which has a cutting edge. In this way they are made thin and of a good shape. Then they are polished with a piece of linen cloth and a little powdered tripoli, and thus they are finished. The letters for printing books are made of a composition of three parts of fine tin, an eighth part of black lead, and another eighth part of fused marcasite of antimony.t The desired quantities of these metals are melted

Jan 1, 1942