Search Documents

By R. F. Burdyn

The inadequate use of centrifugation to economically recover solids from weighted drilling fluids reflects the need for better equipment and techniques for this putpose. Laboratory studies in the development of an improved separator are described in which an operating equation is derived and tested. Results show that the concentric cylinder geometry employed effectively separates bnrite from a suspension and that the operating equation provides a good approxinmtion for scale-up. INTRODUCTION Our current drilling technology frequently requires a high-density drilling fluid obtained by addition of barite. In the course of drilling, formation solids which are too fine to be removed either by screening or settling become suspended in the drilling fluid and gradually the volume of solids in the mud increases. The volume fraction of solids must be limited (if a satisfactory set of rheological parameters are to be maintained). A centrifugal separatorprovidesan economical way of accomplishing this. The barite recovery process can be considered as a separation of two solids. One, the light solids, composed of formation and added solids, has a specific gravity of 2.6 to 2.7; the other, barite, has a specific gravity of 4.2 to 4.3. This density difference, plus the fact that the average light-solids particle size is much smaller than the average barite particle size, permits separation by a centrifuge. In drilling fluids some of the coarse particles of the light-solids-range will settle faster than fine particles of the barite-particle range. As a result a complete separation of the two species is not possible. since the object of the process is not merely recovering the maximum amount of barite but includes as well removing the maximum amount of light solids, an optimum barite recovery efficiency exists. From a practical standpoint this optimum cannot be determined in the field for each drilling fluid system, and in practice the separation is less than optimum, with some sacrifice of barite. Drilling technology has included centrifugal separators for barite recovery for more than a decade. Results have been reported by a number of investigators indicating that the process is practical and economica1. l-4 The decision to use a centrifuge is based on economics in which direct cost savings and the indirect benefits in rig time derived from improvement of the drilling fluid are important factors. One would expect that centrifugal separation of barite from drilling fluids would significantly affect barite consumption; however, this is not the case. The Minerals Yearbook shows an annual domestic barite consumption in the drilling industry of nearly 1 million tons.5 By rough estimate there are perhaps 80 separators presently in field use. Assuming half of these in use at any one time, operating an average of four hours per day, at recovery rates averaging 3,000 Ib of barite per hour, total annual recovery is about 90,000 tons. This is less than 10 per cent of he total barite used. I conservatively estimate that barite consumption in drilling operations can be reduced by 30 per cent through greater utilization of centrifugal separators. To encourage more widespread acceptance of centrifugal separators in the drilling industry, improved equipment and techniques would be very desirable. The present paper, covering theory and results obtained from a laboratory model, is the first in a series on he development of an improved mud separator for field use. THE CONCENTRIC CYLINDER GEOMETRY AS A SEPARATING DEVICE Consider the geometry shown in Fig. 1, consisting of two concentric cylinders separated by an annular space. These are arranged so that the outer cylinder is fixed and the inner one can be rotated about its axis on shafts sealed against the ends of the outer cylinder. If the outer cylinder is fitted with openings at either end, the inner

Jan 1, 1966

Mine Transitman.-Engineer, about 30 years of age, experienced in coal mine underground surveys. Must be good draftsman and possess sufficient personality to get results from the men. Location, Illinois. No. R 419. Coal Mining Engineer: Coal mining engineer of proved ability for position of manager f high-grade bituminous coal property. Location, Canada. No. R 427. Chemist or Metallurgical Engineer.-Chemist or metallurgical engineer for special library work. Man with scientific training with the ability and education -of a young instructor in a university. Duties would consist of working out a new method of indexing scientific information, more particularly in obtaining information for use of a Committee on the Heat Treatment f Steel. Location, Washington, D. C. No. R 470. Topographical Draftsman.-Civil engineering training and topographical and surveying experience. Unmarried man, under 40 years of age. Knowledge of Spanish not necessary. Discharged army or navy man preferred. Location, oil fields, Mexico. Salary, $5 per day, living and traveling expenses. No. R 483. Mechanical Draftsman.-Engineering training, familiarity with drawings of pumps, piping, etc., need not necessarily be a designer. Unmarried man, under 40 years of age. Discharged army or navy man preferred. Location, Mexico. Salary $5 per day with living and traveling expenses. No. R 484. Engineer Translator.-Engineer of Portuguese nationality who has received his technical training abroad, and has been filling engineering positions in this country, to translate material for catalogs of an engineering character. No. R 486.

Jan 5, 1919

UNDER the same justification that I spoke to you in the preceding chapter on crystal and some other gems, I can now speak much better and with much greater reason of glass, since it is one of the effects and peculiar fruits of the art of fire. Every product that is found [41v] in the interior of the earth is either stone or metal or one of the semiminerals, and glass, as is seen, resembles them all, although in all respects it is dependent upon art. Therefore it seems to me that before coming to the discussion of the arts themselves, I must treat of this very beautiful composition created by art and number it with the semiminerals. Thus in this chapter I shall speak to you of glass, not as a proper semimineral, nor yet as a metal, but as a fusible material that is almost made mineral by art and by the power and virtue of fire, born from the speculation of good alchemistic savants, through whose efforts it imitates. the metals on one hand and the transparency and splendor of gems. on the other. Certainly it is a very beautiful thing and one that should not be left buried in silence, in consideration first of how great a thing art has been, able to discover, and then because its beauty makes it such a pleasing thing for making drinking. glasses and an infinite number of other ornamental things that satisfy the desires of man. I shall begin, then, by telling you, to the credit of the alchemists, how I believe that this thing was found through their desire to make gems; for when they could not bring them to perfection (as also happened with the metals) they made this beautiful and attractive product, glass. However, Pliny says that it was found by chance in Syria at the mouth of the Belus River by certain merchants who were driven there by the fortunes of the sea and forced to stop and disembark there for a time in order to eat. In cooking the food they saw the rocks of that place converted into a flowing, lustrous material. And as they thought about this, it seemed beautiful to them, and when they went away they carried some stones and plants with them. Thus they gave beginning to glass making. But now leaving this discussion it does not matter how it may have been discovered, whether by merchants or by ingenious alchemists. Art is that which has given it being, through many experiments and by addition

Jan 1, 1942

By William C. Maurer

A survey of 25 novel drills has shown that spark drills have potential for drilling oil wells and blastholes at higher rates than rotary drills. Available laboratory and field data were extrapolated to drilling rates of 70 to 280 fph for full-scale spark drills. Most of the data used in these extrapolations were from small-scale laboratory tests at atmospheric pressure. Accurate extrapolation of the small-scale spark drill tests to full-scale field drills was complicated by the fact that the effect of fluid pressure in the well bore and the effect of spark size were not known. In order to answer these questions and to more accurately evaluate the potential of spark drills for drilling blastholes and oil wells economically, a high-voltage spark discharge system was assembled. This equipment produced powerful sparks (10,000 joules) equivalent to those that would be used on a 100-kw full-scale field drill. These sparks are 100 times more powerful than those previously used on spark drills, thus eliminating extrapolation of the spark size. In addition, a pressure chamber was modified to enable using these sparks to produce craters in rocks at fluid pressures up to 15,000 psi, thus eliminating extrapolation from atmospheric pressure to the high pressure existing in deep oil wells. These tests have provided considerable information for more accurately evaluating spark drills for oil-field drilling. MECHANISM AND THEORY OF SPARK DRILLING Spark-Drilling Mechanism When a high-voltage capacitor is discharged across two electrodes, the dissipated energy produces a high-temperature, high-pressure plasma for a few µsec. When these sparks are discharged in air, they undergo considerable expansion (Fig. 1) and produce low-pressure pulses (103-

Jan 1, 1970

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove' In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove' In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By E. A. von Hahn, T. R. lngraham

The rates of cementation of pd11 on electropolislzed copper cylinders were studied in aqueous perchloric acid solutions at pdII concentrations from 0.02 to 0.1 mM. The cylinders were rotated at various high speeds to reduce the diffusion layer to a minimum thickness. In 0.1 M HClO4 solutions, the cemented palladium is dense, adherent, and shiny. The rate data indicate that there are two stages in the deposition. In the initial stage, the rate of cementation is first order with respect to the pd11 concentration. The second stage is much slower. The first stage is consistent with rate control by the diffusion of pd11 ions to the copper surface, and/or chemical reaction at the surface, and the second stage is consistent with rate control by the diffusion of copper ions from the cop-per surface through the deposit of cemented palladium, out to the main body of solution. In 0.001 M HClO4 solution, only the first stage is evident and the rate is more rapid than at higher acidities. This rate enhancement is attributed to PdOH+ ions that predominate at low acidity and aye more reactive than unhydrolyzed pdII. The deposit is porous and loose. All of the cemented deposits are Pd-Cu alloys rather than pure palladium. Activation energies are 9.5 kcal per mole in 0.1 M HClO4 and 7.4 kcal per mole in 0.001 M HClO4. CEMENTATION or displacement reactions occur between aqueous solutions of metal salts and immersed metals according to the general equation: where M1 is electrochemically the more noble metal. Although these reactions find considerable application in metals recovery processes (e.g., the cementation of copper192 or gold3), in electrorefining processes (e.g., solution purification before electrolysis4,5), and in plating and metal finishing processes,6 few studies have been made of the kinetics of such reactions.7-9 The rates of cementation reactions will depend on one or more of the following factors: a) chemical reactions at the metal-solution interface; b) ionic transport to or away from the interface;'-' and c) the character and adherence of the cemented deposit on the substrate metal,6a,10 because the deposit will inhibit the rate of transport of dissolving ions (M2m+) into the solution. In this investigation, the kinetics of the early stages of cementation were studied to obtain an understanding of the reaction mechanism under conditions in which the deposit was sufficiently thin that its inhibiting effect could be disregarded. To achieve this, very dilute solutions in Mn+ were used. Cementation rates are often fast in the initial stages and transport-contr01led.9 To find conditions under which transport control would shift to chemical control, very high stirring velocities were used to minimize the diffusion-layer thickness. Of the many possible cementation reaction systems, the palladous perchlorate-copper system was chosen for this investigation because it was believed to involve simple ion-for-ion exchange. In addition, there are no interfering side reactions, such as the reduction of hydrogen ions, and anion effects are usually absent in perchlorate solutions. EXPERIMENTAL Materials. Reagent-grade chemicals and redistilled water were used in all experiments. Palladous perchlorate stock solutions (0.02 M) were prepared by dissolving 99.5 pct Pd sponge (Johnson Matthey and Mallory Ltd.) in concentrated nitric acid, adding concentrated perchloric acid, evaporating twice slowly (to prevent PdO precipitation) to a small volume, and diluting in a volumetric flask. To prevent gradual hydrolysis of PdII, the stock solutions were made 0.4 M in HC104. Tests for pdIV (Ref. 11) and C1- were negative. Copper strips were cut accurately from 0.025-in. electrolytic tough pitch sheet, Sample 1 (Mines Branch stock or Canadian Copper Refineries Ltd., Montreal), or from oxygen-free, high-conductivity sheet, Sample 2 (American Metal Climax O.F.H.C. brand, sold by Utility Brass and Copper Corp., Brooklyn). The strips were annealed for 1 hr at 335°C in a stream of purified nitrogen (Union Carbide, Linde Division) which had

Jan 1, 1967

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By H. W. Turner

Lying to the east of the Rio Grande, in central New Mexico, is a long N. and S. mountain range, broken into separate ridges at several points. These have received separate names; the mountains at the south end, near El Paso, being known as the Franklin mountains, and then, following successively, to the north, the San Andreas range, Sierra Oscura, Manzano and Sandia mountains. At the eastern base of the Sierra Oscura there are several low ridges, remarkable for their red color. All of these red ridges contain reefs of copper-ore. The eastern flanks of the Sierra Oscura are composed of limestone. Some fossils in the limestone were examined by Prof. J. P. Smith of Stanford University, who says they are Fusulina and indicate an Tipper Carboniferous age. The sandstones and shales containing the copper-reefs directly overlie this limestone (Fig. I), and are very likely of Permian age, like the similar beds in Texas, described by Mr. W. F. Cummins.* Overlying the copper-beds are red sandstones and shales in which very little copper has been found. The cupriferous zone and the red sandstones and shales are everywhere associated, and as one stands on a high point, he will see that these rocks form three main belts or lines of hills. These may be referred to as the northern, middle and southern belts. The northern belt was not visited by me, but is known to contain copper-deposits. The middle belt has a trend of N. of W. and S. of E. The copper-reefs have been traced for a distance of more than 2 miles. The southern belt has a trend of about N. 30' W. and S. 30°

Jan 1, 1903

In March 1956 a conference on geochemical methods of prospecting for ore deposits was held in Moscow. This conference was the culmination of a ten-year period of extremely rapid increase in both research and routine application of geochemical prospecting methods in the USSR. This activity was divided among groups centered in extremely widely separated bases of operation, ranging from Moscow and Leningrad in the West, Yerevan in the Caucasus, and Alma-Ata in Central Asia to Chita near the Manchurian frontier in the Far-East. The All-Union Conference on Geochemical Methods of Prospecting for Ore Deposits, as the meeting was called, was the first opportunity for these scientists from many parts of the country to meet and exchange experiences. It also served to introduce members of the different research laboratories located in the city of Moscow itself, where adequate channels of technical communication had not yet been established. As a result of the Conference, it was resolved that a concerted effort should be made for the participants to publish the results of their work. Two books have appeared as a direct response to this resolution. I. I. Ginzburg prepared a synthesis of the field of geochemical prospecting for minerals based on the material presented at the Conference. This volume has been translated into English and is now available. In addition, the individual papers presented at the Conference were assembled into a symposium volume and published in 1957 under the editorship of V. I. Krasnikov. Unless otherwise noted, these two books have supplied the source material for the present appraisal of the status of geochemical prospecting in the USSR. It is thus about four to five years old. In the years following the conference, the literature has carried a substantial volume of technical papers, together with a few monographs pertaining to specialized aspects of geochemical prospecting.

Jan 6, 1960

By Samuel S. Wyer

The following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests— which has some resemblance to the code of boiler-trials of the American Society of MechanicalEngineers—has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same thing, to see if the efficiency is as high as it should be with the type of producer in question; and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the'producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins,' the efficiency was raised from 56.2

Jan 1, 1906

By Charles E. W. Bateson

The Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low range of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. Climate and VEgetation. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera ture is generally from 60" to 70" F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100" F. in the day-time, while 115" F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1907

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

By B. A. Rogers

ACCORDING to petrographic investigations, 1-4 cooled steel furnace slags contain a number of substances that have been shown to be ferro-magnetic5,6 and hence capable of undergoing appreciable changes of susceptibility with temperature. Since any alteration of the suscepti-bility of a constituent affects the average susceptibility of the sample, information concerning the nature of the substance should be deducible from its magnetic behavior. The possibility of obtaining information concerning slags in this way led to the construction of the apparatus to be described. FUNDAMENTAL PRINCIPLES OF APPARATUS The most convenient method of observing changes in mass suscepti-bility? with temperature is the one employed by Curie7 in his original investigation of the changes in magnetic properties of substances at elevated temperatures. As the method has been described frequently in the literature and in textbooks, only a brief review of the fundamental principles need be given here, but the particular arrangements used in the present work require a more detailed description.

Jan 1, 1939

By Renato G. Bautista, KNona C. Liddell

A model of the reaction of chalcopyrite, CuFeS2, with Fe3+ and with 02 is considered. Homogeneous solution phase reactions are assumed to be always at equilibrium throughout the dissolution of the mineral. The dissociation of USOb- and several complexation reactions involving cu2+, Fez+ and Fe3+ are incorporated in the model equations. The relative importance of Fe3+, 02, and H+ as oxidants and the role of solution equilibria are assessed and the implications for leaching practice discussed.

Jan 1, 1981

By R. T. Rometti, C. A. Bossard

INTRODUCTION Whenever a new mining property is developed or a new concentrator is built, considerable time, money, and planning are invested for the exploration, engineering, and construction of the required facilities. Yet, when these facilities are ready for startup, all too often insufficient time, money, and planning are invested in this critical phase of the project. Failure to plan for this phase results in untimely personnel mobilization, insufficient operator training, and inadequately prepared budget estimates, which combine to create excessive costs, lack of communication, unclear responsibility divisions, unnecessary delays, and poor production levels. Insufficient or excessive leadership, due to unclear assignment of responsibility, results in irrevocable problems within the startup team. A carefully planned and budgeted startup phase can avoid many of these problems. SCHEDULING A key element in properly planning the startup phase lies within the area of scheduling. Once the schedule has been established, planning can be greatly simplified through the expansion of each specified item. The overall project schedule should specify the date when the startup and initial operating management team will be brought onto the project. This team should be mobilized at least two years prior to the anticipated startup date, to allow sufficient time to begin to plan, assemble the startup groups for the various areas of the plant, initiate a workable communications system, and implement the development of the training program. This team is responsible for the preparation of a startup schedule, which would detail the dates for all key items associated with this phase of the project. These key items would include training program development, personnel hiring dates, prestartup plant checkout, etc.

Jan 1, 1982

Ocean environmental factors are an intriguing new set of parameters to be dealt with in the prospecting and exploration phases of resource development for both the continental margins and the deep ocean. While information and data gathering programs for ocean minerals would parallel onshore procedures, their costs generally run higher. Commercial Prospecting-Identification of Mining Sites Two modes of prospecting can be identified-commercia1 prospecting (in which the ultimate objective is to define potential mining sites), and scientific prospecting, which is conducted with different objectives in mind. For ocean exploration, both types of prospecting are carried out prior to the obtaining of any exclusive rights to explore and exploit a specific deposit. Deepsea's John Flipse adds: "Any commercial prospecting program should by its very nature require the freedom to search wherever minerals might occur with maximum flexibility."

Jan 4, 1975

By Arthur V. Abbott

During the past four years I have had occasion to make quite extensive use of steel castings in the manufacture of testing-machines and large scales for Messrs. Fairbanks & Co. The failure of some of these' castings at stresses much below those which were claimed for them by the makers, induced me to institute a series of experiments to determine the actual constructive value of the steel castings now to be obtained in this country. The art of steel-casting is rapidly improving, almost every issue of the scientific press bringing accounts of some new development; consequently, the results of the following experiments are only exponents of the value of steel castings as at present made. In order to make the examination as thorough as possible, ten sets of patterns were made and forwarded to as many different firms in the country who advertised to make steel castings. The first part of the accompanying table gives a list of these manufactures, together with the price per pound. The order accompanying the patterns simply requested the manufacturer to supply two castings from each pattern of his ordinary product of steel. These castings were sent to me and paid for in the usual manner, so that it is probable that the samples fairly represent the quality of the average of steel castings, and are free from the suspicion of being "special runs." Two patterns were sent to each maker, one being a straight

Jan 1, 1886

By John B. Hastings

Chief among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr' is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. "The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerons, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the

Jan 1, 1906