Search Documents

By James E. Lawver

Efficiency of industrial research and development depends on the ability of engineers and scientists to collect and present data to top management for decisions. In many cases, the data presented are so deceptive that management makes costly wrong decisions. Since management personnel often are selected on the basis of higher administrative quality than technical ability, it is the responsibility of the industrial scientist or research engineer to make certain that the data presented tell a completely ac- curate story of each industrial problem. It is rare that misleading data are deliberately presented, but when this is done, it is? of course, dishonest. The rise of deceptive data usually stems from the lack of knowledge of experimental design and statistical methods of analysis. Most of the better chemical engineering schools have recognized the need for courses in industrial experimentation and many of them offer complete courses at both graduate and un- dergrarluate levels. By contrast, many of the mining and metallurgical schools have not recognized the importance of industrial experimentation courses and some of them, in fact, do not allow credit toward a mining or metallurgical engineering degree for statistical courses even when taken as an elective. The sole purpose of this paper is to make a plea for mining and metallurgical schools to present required industrial. statistical courses for their graduates. It is true that fine industrial research has been accomplished in the past without the assistance of any statistical techniques. Industrial problems have also been solved without the use of digital or analog computers, electron microscopes or other modern conveniences. The fact remains, however, that the correct use of these modern tools tends to reduce the cost of research and to eliminate costly errors. A working knowledge of experimental design and statistical data analysis must simply be viewed as a valuable tool whose proper use will greatly reduce the cost of experimentation and minimize the cost of false conclusions. These statistical methods, however, simply cannot replace fundamental knowledge or, for that matter, "good horse sense". Nevertheless. an experimenter armed with fundamental knowledge and good horse sense but completely ignorant of elementary statistical techniques, may easily present his data in such a deceptive form to cause management to make incorrect decisions.

Jan 6, 1962

By Samuel H. Dolbear

NOT WITHSTANDING the extremely low ebb of business activity, the nonmetallic industries have fared somewhat better than some other branches of mining. The average price level in nonmetallics, although far from satisfactory, has resisted any cataclysmic fall such as has been suffered by copper and other metals. Stocks, also, though too abundant, represent no corresponding overhang of the market, which should result, in some branches, in a more rapid recovery. Research work has continued in some industries with interesting developments.

Jan 1, 1933

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4º; wet-bulb, 57.4º; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down- cast shafts; however, the variation between winter and summer causes a difference of only 2º to 3º in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of the mine are as follows: [ ] There appears to be no difference in rock temperature for any particular horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock temperatures given above is 1 ½ º per 100 feet. Underground Waters.-The underground water varies from 350 to 565 gal. per min., depending on the rainfall. The limestone and other

Jan 1, 1938

By C. S. Witherell

THE first feature that strikes one when considering the use of air enriched with oxygen in pyrochemical processes is the conservation of Enriched Air FIG. 1.-TEMPERATURES THEORETICALLY OBTAINABLE BY BURNING PURE AMOR¬PHOUS CARBON IN AN ATMOSPHERE COMPOSED OF AIR ENRICHED WITH OXYGEN, PRODUCING GAS CONTAINING CO. heat due to the partial elimination of the inert heat-carrier nitrogen, as set forth in the report of the committee. The second feature, which

Jan 11, 1924

Curiously enough, considering the relative accessibility of the two places, coal was reported at an earlier date in Saskatchewan than in British Columbia. Henry and Thompson were on the Saskatchewan River in February 1811, and on the 4th of that month recorded, while on Jack's Branch of North Brook, "I observed in one of the bends on the north side a bank of yellow clay, on which there appeared several horizontal veins of pure coal, of the best quality I have seen along this river." Later at Rocky Mountain House it was said: "a quantity of coal is tumbling into the water, as the current washes away the earth underneath. This coal abounds along the Saskatchewan, in some places forming solid beds several feet thick for several acres, which are washed by the river. In its pure state our smiths use it for the forge with equal proportions of charcoal made of birch or aspen, which answers every purpose for making and repairing our axles and other tools."1 It is needless to say that it was many years before this coal was used for any commercial purposes. Coal was first found on the northern end of Vancouver Island in British Columbia in 1835 at Beaver Harbor, where later Fort Rupert was established, where Indians had advised some of the Hudson Bay Company officials it would be found.2 The coal was used by smiths, and later on by the steamer plying along the coast.3 A report to the government in 1845 called attention to the coal reported in the neighborhood of Puget Sound and on the Cowlitz River, and that probably the samples used by the Hudson's Bay Company were obtained from the surface and. were not good. On September 7, 1846 a report on the coal situation was submitted by Ogden and Douglas, and a naval vessel was sent to investigate the report and was loaded with 62 tons dug out by the Indians, the seam outcropping along the shore.2 In 1847 some samples were sent to England by a returning war vessel. In 1849 the Hudson's Bay Company established a

Jan 1, 1942

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

By K. F. G. Hosking

I read Professor Gaudin's paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S,), is ground with sodium or potassium hydroxide, the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture.

Aug 1, 1956

By John H. Hearding

Induction heating, together with automatically controlled tempering and hardening is giving Oliver faster and more accurate bit sharpening, while experiments with bit taper promise to offer increased footage per bit.

Jan 10, 1953

By Charles Hardy

?POWDER METALLURGY? is the production of semiformed or fully formed metal products by compressing metal powders. It had its beginnings in the fabrication of tungsten and molybdenum bars and wire by compression, sintering, and swaging. Powder metallurgy, although still in its infancy with other metals, has shown remarkable progress in recent years. Production of Metal Powders-The first step in any powder-metallurgy process is the production of metal particles of suitable shape and size. Mechanical processes for producing metal powders, as by crushing, stamping, or grinding, are usually not suitable, as the resulting particles may cause laminations and decreased strength in the finished articles. The principal metal powders now in use on a large scale are produced by electrolysis or by reduction of metal oxides by gases.

Jan 1, 1936

By AIME AIME

HOWARD H. PRESTON, professor of economics and business at the University of Washington, presented a paper before the North Pacific Section, A.I.M.E., on Jan. 23, on the "Economic Aspects of Gold and Silver." He carefully reviewed recent governmental actions that have affected those metals and gave an interpretation of their effects. A brief excerpt from his address; follows: Including the proclamation of March 6, 1933, the principal steps of the present Administration which have carried the United States off the gold standard and led up to the present program have been: (1) The Presidential proclamation of March 6 controlling gold. (2) The monetary sections of the Emergency Banking Act of March 9. (3) Mobilization of gold under Executive orders issued March 10 and April 5. (4) The gold embargo by Executive order, April 20. (5) The controlled inflation bill, May 12. (6) The joint resolution abrogating the gold clauses, June 5. (7) The Executive orders on newly mined gold, Aug. 28. (8) The President's radio address of Oct. 22 and the R.F.C. gold-buying program. (9) New anti-hoarding order calling in small holdings of gold, Dec. 28, 1933 and Jan. 15, 1934. (10) Nationalization and revaluation of gold' (Message to Congress, Jan. 15).

Jan 1, 1934

By R. A. Wagstaff

The method of charging a reverberatory furnace has changed many times since smelting was introduced in this country from the old smelters of Swansea, England. The cause of the latest change at the Garfield plant has been the excessive fineness of the charge due to fine grinding in the concentration of the crude copper ores. The many desirable features of deep-bath smelting as now used at Garfield have been proved. The old method of dropping the charge through holes in the arch (known as center-feed method) causes excessive dusting which makes heavy slag and flue-dust losses, also rapid deterioration of the silica brickwork of the furnace through fusion with the iron oxides from the dust. The purpose of this paper is to describe a gun feeder that was designed to overcome the disadvantages of the older methods of center feeding and still maintain the good features of deep-bath smelting with the hot finer charge. A gun feeder was designed to introduce the finely divided hot calcines under the moving gas stream of the combustion zone and still have them spread in a uniform blanket over the highly heated matte bath. The temperature of the furnace was so great that it was impossible to maintain a stationary feeder, so a movable feeder was designed that could be introduced into the highly heated zone and be withdrawn after the charge had been dropped. It was necessary to protect the nozzle of the gun with a water-cooled coil. Many different types of protected nozzles were tried, such as air jackets, water jackets and heat-resisting steel alloys, but none proved satisfactory. The angle of inclination of the feeder was found to be an important factor in spreading the charge evenly over the surface of the bath. An angle of 34" to 37" was found to be the most advantageous. To allow a continuous flow of ore from the charge car to the point of discharge inside the furnace, the feeder was made with telescopic connections. The pipe leading from the car is stationary and forms the inside part of the telescope. The outside section of the telescope is movable, and is

Jan 1, 1934

By William R. Webster

At the Richmond mecting in February, 1901, I presented for discussion the proposed rail-specifications of Committee No. 1 of the American Section of the International Association for Testing Materials, with a review of their work, and other matters relating to the heat-treatment and chemical composition of steel (Trans., xxxi., 455). In order to bring out the views of our members on the important points referred to, I offered for discussion the following questions and comments (trans., xxxi., 972): " 1. The advantages to be gained by using more metal in the flanges and web of the heavier sections of rails.

Jan 1, 1903

By Sam Tour

OF the new alloys achieving commercial prominence during the year, an aluminum-silicon magnesium casting alloy, which is similar in many respects to the 4 per cent copper alloy, developed about 1921, which has attained such a wide field of service, may be mentioned. The new alloy, like the old, is a heat-treatable type and develops about the same physical properties. The alloy casts easily and is relatively insensitive to high pouring temperatures. Its ability to produce substantially leak- proof castings is noteworthy. A second casting alloy development is the new Aluminum Co. of America No. 132, "Lo-Ex" piston alloy, a result of nearly eight years of research. The alloy contains about 14 per cent silicon and varying amounts of nickel, copper, and magnesium. It exhibits a low coefficient of expansion and thus permits small piston clearances. Its lower specific gravity is a further advantage.

Jan 1, 1932

By Clarence E. Sims, George A. Moore

INTRODUCTION IN previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficient time is allowed. For precise work, the method claims preference because the equipment for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the transformation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approximately 2 hr. While it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual error may be more or less constant between samples. For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temperature process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and evolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1948

By Eugene A. Stephenson

NUMBER of noteworthy events in the petroleum industry may be reported for 1941, of which the most spectacular was doubtless the rise in the daily rate of crude-oil production to a peak of approximately 4,300,000 barrels. This enormous daily rate did not ensue from the furor of flush pools but represented for the most part merely a slight additional daily delivery from many wells that had previously been operated on a more restricted basis, in line with good conservation practice and also from the adroit increase in the number of days per week by the Texas Railroad Commission. Another important fact was the increase in price throughout the Mid-Continent area from the static level of $1.02 for 36°, A.P.I., crude, to $1.17 per barrel. Efforts to elevate the price above this point have met with severe opposition from the O.P.A.. as has also a similar effort by the PennsyIvania Crude Oil Producers' Association, but the vastly increased costs for materials and labor may shortly give the industry the enhanced price which it has long deserved.

Jan 1, 1942

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By E. J. KENNEDY

METHODICAL AND EFFECTIVE: thus may be characterized the fall meeting of the Iron and Steel and Institute of Metals Divisions at the Hotel Statler, Buffalo, N. Y., on Oct. 4 and 5. Approximately 200 registered. Interest centered 1111 the technical papers which were keenly followed, with substantial discussion: During the entire week of the National Metal Congress (Oct. 3 to 'i), there were also other sessions of interest' to metallurgists, directed by the America11 Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron arid Steel and Machine Shop Practice Divisions of the American Society of Mechanical En,' the Wire Association and the American Drop Forging Institute. The National Metals Exposition at the 174th Regiment Armory was well attended.

Jan 1, 1932

By A. B. Kinzel

IT is with sincere appreciation and a deep sense of responsibility that I accept the honor of delivering the Howe Memorial Lecture. In our time metallurgical research has delved into phenomena ever more complex in character, so that much of this work must be done by organized teams. We, of the Union Carbide and Carbon Research Laboratories and the Electro Metallurgical Co., are truly a team and the lecture which is to follow is due largely to a few of the outstanding members of that team here cited and well known to you in their own right: John Lamont, whose work deserves special recognition, Walter Crafts, William Forgeng, William Binder, Robert Fowler, and David Swan. Thus it is a fitting pleasure to accept this honor for the research institution which I represent. Henry Marion Howe was truly inspirational and his breadth of view was such that he could use either the method of rigid proof or implied mechanism to further the broad understanding. But perhaps his outstanding characteristic was his sound judgment and his ability to weigh observations. The following is replete with observations and judgment as to their implication. We would like to feel that it is the type of dissertation which Howe, himself, would have enjoyed. Chromium carbides in stainless steel have, in a sense, been a key to the progress of the stainless steel industry. Brearley's first stainless steel, containing approximately 0.30 pct C, was successful because it differed from previous Fe-Cr alloys in that the carbides were present in such amount and form as to provide the stainless and cutting properties. Again, the 12 pct Cr die steels with a carbon content of 1.5 pct or more achieved their properties by virtue of the form and distribution of the chromium carbides. In the straight chromium steels with from 12 to 25 pct Cr, chromium carbide amount and distribution are once more the determinants with respect to physical properties and corrosion resistance. In each of the cases just cited the role of the carbide is in essence similar to that of iron carbide in carbon steel and this story is so well known that we need not dwell on it. In the austenitic stainless steels, the chromium carbide plays only a minor positive role with respect to mechanical properties, and for corrosion resistance the objective is to achieve maximum homogeneity. Thus the tendency has been to ever lower the carbon and correlatively the chromium carbide content of the austenitic steels. Today stainless steels with carbon less than 0.03 pct are beginning to find their true place, and this is being aided in major degree by our Company's introduction of a new type of ferrochromium having negligible carbon. The role of carbon in these austenitic steels has long been recognized, and a truly enormous amount of research has been devoted to the subject. Much has been learned about corrosion resistance, but the attack on the problem from the point of view of carbide precipitation and the nature thereof has left much to be understood. Because of its fundamental importance to the future of stainless steels, further study of the mechanism of carbide formation in austenitic steels is of interest. In the 18-8 Cr-Ni steels, which are typical of the austenitic class of steel, carbon is soluble in the aus-tenite to the extent of approximately 0.15 pct at 1832°F (1000°C). The solubility becomes less with decreasing temperature, so that at 1652°F (900°C) the solubility limit is approximately 0.06 pct, at 1472°F (800°C) it is about 0.03 pct, and at 932°F (500°C) it is approximately 0.01 pct. Obviously this is the ideal situation for the classical precipitation phenomenon. It is true that, in a sense, 18-8 austenite resulting from annealing is in a metastable state, and the phenomenon of ferritic precipitation from this austenite should be considered. However, in a so-called fully austenitic 18-8 steel this is secondary with respect to the carbides and can be neglected. A wide variety of chromium carbides is known. Only one chromium carbide, Cr,,C,,, frequently referred to as Cr,C, has been found in unmodified low carbon 18-8 steel. This, fortunately, simplifies the study of the precipitation phenomena. For this study an A.I.S.I. type 304 stainless steel of commercial quality was selected. Analysis showed C 0.07 pct, Mn 0.49 pct, Si 0.33 pct, Ni 9.34 pct, Cr 18.91 pct, and N 0.033 pct. As expected with this composition the steel was homogeneous after annealing except for a few pools of ferrite, which were disregarded in that their location was not coincident with subsequent carbide precipitation areas. On corrosion testing the steel was normal and typical of good commercial quality. Specimens 1/2xlx4 in. were annealed and subjected to precipitation heat treatment for 100 hr at 100" temperature intervals from 1000° to 1500°F and for ten selected intervals ranging from 5 min to 64 hr at 1300°F. These blocks were then cut into small pieces for metallographic studies. The first problem

Jan 1, 1953

By Elton A., Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11 mile bus ride up Railroad Creek to Holden. All freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting.

Jan 1, 1949