Search Documents

By Clemens Jones

An interesting paper by J. E. Merion and Edward Hart, in Volume I., No. 2, of the Journal of Analytical Chemistry, on the Decomposition of Blast-Furnace Cinder by Acid, describes a plan of sampling the cinder by means of a previously-heated iron bar thrust into the cinder car or into the cinder at the notch, and then allowed to cool, thus chilling the cinder which adheres to the bar, and rendering it decomposable by hydrochloric acid, of 1.12 sp. gr. A short series of results is given, from which the deduction follows that blast-furnace cinder " is decomposed perfectly when chilled." Where many silica determinations are to be made, this method, if reliable, would effect notable economy of time and reagents. The conversion of insoluble silicates by fusion with an alkaline carbonate, together with the subsequent solution, evaporation, drying, etc., is destined to remain the standard method. But all fusionmethods are time-consuming and expensive. Chilling appears to render the supplementary method available for all practical purposes, in the determination of silica in cinder. But, with a view of securing more evidence on the subject, and in view of the fact that uniform results were not obtained by employing this method, it was decided to test the method in the laboratory of the Thomas Iron Company where a large number of silica determinations are made. The experience met with may not be devoid of value, both theoretical and practical. Mr. Iles's paper, in the Chemical News, Volume L., 1881, doubtless suggested to several chemists, connected with iron metallurgical

Jan 1, 1888

By Robert Lewis

Some recent experiments in the use of compressed air for rock drills at higher than usual pressures, up to 150 lb. per sq. in., emphasize the importance of maintaining the compressed-air system in the best condition if the greatest possible over-all efficiency is to be secured. No claim of high over-all efficiency can be made for the compressed-air system of braking that is used on railroad trains, yet the air brake works effectively. Compressed air is not used efficiently in the rock drill, but no other type of machine drilling is yet a serious competitor of the air-driven rock drill.

Jan 1, 1930

By AIME AIME

TWO days of solid discussion, with barely time out for meals, characterized the Tulsa meeting of the Petroleum Division. It was preeminently an earnest gathering devoted to technical matters. Sessions were held in the Crystal room of the Mayo Hotel with luncheon served each day in the back of the same room so that talk of methods, while slightly less formal, extended right through the lunch hour. Thursday evening the Committee did provide a little relaxation in an informal dinner at the Tulsa Club where, after a brief musical program and an amusing skit by the local Herman the Great, brief addresses in non-technical vein were made by President Farish and Vice-president Rice of the Humble Company, Henry L. Doherty of Cities Service, Secretary. Bain of the Institute, and others. The presence of leading executives of a number of the oil companies at the dinner and the sessions, and the cordial approval they expressed of the work of the Division were especially gratifying. The total registration was 215 with 100 at the dinner and 70-to 80 lunching together each day.

Jan 1, 1930

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

By J. S. UNGER

A LARGE proportion of the coke used is made in the by-product oven from the high-volatile coals mined in the adjacent district. At the beginning it was feared good by-product blast-furnace coke could not be made with our coals. By experimenting with various mixtures of coals, coking time, oven design, and coking temperatures, much has already been accomplished. The results show that a hard, dense coke, not easily broken by handling, can be produced. In its present state it is not all that could be desired, but it is being constantly improved. Such coke has been used alone as the fuel on several of the blast furnaces producing the highest daily production in the Pittsburgh district. Many of the coals in the Pittsburgh district when coked in the by-product oven yield a gas which contains a high percentage of sulfur, which is objection- able for many metallurgical operations. As this fuel is gradually replacing the ideal fuel, natural gas, which is becoming less plentiful, studies are being made of the best methods for purification. Some metallurgists believe sulfur to be a very injurious element in steel. Recent investigations by Government bureaus, scientific bodies and private firms, seem to indicate that a reasonable amount of sulfur may exist in steel without detriment. Without wishing to provoke any metallurgical controversy on the subject of sulfur, the fact remains that the daily purification

Jan 1, 1926

By F. O. Garrabrant

POWER is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt line to a bank of three 3333-kva. Transformers 100/13.8 kv. These transformers arc so designed that with the addition of forced cooling their capacity may be increased 33 1/3 per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200- amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. MINE Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three 250-kva, 13,800/440-volt, single-phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp. motor on the No. 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 100-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft. Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. Under normal operation the one pumping 1200 gal. per min. is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started, and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the pumps restart. On failure of any of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 370 substation is run to the switching station, in which are four15-kv., 600-amp. direct-current solenoid-operated oil circuit breakers. The current for operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1944

By R. D. Pehlke, J. F. Elliott

The equilibrium pressure of nitrogen gas over pure silicon metal and silicon nitride has been measured in the temperature range 1400° to 1700°C. From the experimental data, the standard free energies and enthalpies of formation of Si3N4(a) have been calculated as functions of temperature over the above temperature range. Utilizing data in the literature and the results of this investigation, the specific heat, molar enthalpy, molar entropy, standard enthalpy of fornation, and standard free energy of fornation are estimated for the temperature range 298° to 1400°C. THE high-temperature thermodynamic properties of many metallic nitrides are not well established at present. This is a serious deficiency because nitrogen and nitride-forming metals are important alloying additions to steels, and knowledge of the interaction between nitrogen and these elements is essential to a better understanding of the behavior of steels. Metallic nitrides also are used as refractory materials. Consequently, the investigation reported here was undertaken to provide more complete information on the standard entropy and free energy of formation of silicon nitride. The experimental technique provided a direct measurement of the equilibrium pressure of nitrogen gas in the range of 1413 to 1700°C for the reaction: 3 Si(1) + 2N2 (g) = Si3N4 (a) [ 1 ] and below 1413oC for the reaction: 3Si(c) + 2N2(g) = Si3N4(a) [2] APPARATUS The experimental system consisted of a crucible assembly, a reaction chamber, and a gas supply and vacuum system. The Crucible Assembly which contained the equilibration specimen and molybdenum radiation shields with a susceptor for induction heating is shown in Fig. 1. Two covered, high-purity alumina crucibles, one nested within the other, contained the susceptor, shields and specimen. Central openings in the upper shield and crucible covers permitted on optical pyrometer to be sighted into the central cavity of the specimen. The specimen itself was a 5/8 OD by 1-in.

Jan 1, 1960

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879

By Grafton M. Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by me in Metallurgical and Chemical Engineering for January, 1915. Several years ago, while I was chief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in both open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the silicon in every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 1, 1916

By AIME AIME

DURING my senior year at college a professor said to his class that a student who failed to obtain a passing grade in that certain subject could not graduate with his class and that his diploma would be withheld until the failure had been removed. In that way for four years a diploma had been made to appear to us as the objective in attending college. We grew up to think that a diploma was the means of providing employment; consequently, a diploma could not be jeopardized and, heeding the professor's remarks, we resolved to put forth special efforts and make good. During one of our class periods this same professor digressed briefly from his prepared lecture in metallurgy and advised the boys to join a national technical society. He spoke with earnestness and sincerity. After class we students discussed those remarks. We concluded that the professor had not convinced us. We were already members of technical societies at school and saw no need of joining another. In fact, even up to that moment a society had never indicated to any of us that joining it had any relation to landing a job, and we were fully aware that joining another society meant paying out more money, for fees and dues, which money we then needed to buy food, clothes, and perhaps a new slide rule. Furthermore, we knew that joining a society was not part of the curriculum and, therefore, the diploma could not be withheld if we did not follow the advice. Our conclusion was that we would not join but would concentrate on our work that assured getting our diplomas.

Jan 1, 1936

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By VlNTON H. CLARKE

Diamond-drill blasthole sloping has now been used for a long enough time to permit us to discuss fairly its problems from the ore-breaking angle and to attempt to peer into its future. To do this we have gathered information from many properties through questionnaires. The operators have indicated fairly well in their answers what they think of the method. The many variations of methods have by now been fairly well developed, and performance rates and. mining costs are well established at each property. All this can be laid down on paper with fair completeness. Now. knowing all this, what will the future of the method be? To attempt to look into the future of a mining method immediately brings to light many problems and variables. For instance: why were diamond drills used in the first place? What has the cost trend been? In what type of deposit has the method proved most advantageous? What will the future cost of diamonds be? What are the possible substitutes?

Jan 1, 1949

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By Anthony Lucas

THE discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has grown with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover, despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting, and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable

Jan 7, 1918

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the Mast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success is made of wrong- ht-iron tubes, 29 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglornerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By Vernon A. Mrak

The Powder River Basin of northeast Wyoming was the first area in the state to receive attention during the early days of uranium exploration. Although the uranium occurrences are many and widespread, most of the known ore deposits are quite small and difficult to mine. As a result of this, detailed regional exploration in the Powder River Basin has been neglected. The uranium ore deposits occur in that part of the Wasatch Formation that is of earliest Eocene age, and they are scattered over an area of about 400 square miles. All uranium ore deposits are associated with red beds or altered sandstones within the Wasatch Formation. Uranium ore was first shipped from the region in 1953. Total production through June of 1965 is 506,257 tons of uranium ore containing 1,922,527 pounds of U3O8. The average grade of ore is about 0.19 per cent U3O8. The major producing area of the Powder River Basin is the Monument Hill district where about 91 per cent of the basin's total uranium ore has been mined. The source of uranium is presumed to have been the Oligocene, Miocene, and perhaps Pliocene tuffaceous rocks that once overlay the area. Joints, fractures, and permeable beds or zones were the passageways for the migration of uraniferous waters from the overlying beds to the Eocene host rocks.

Jan 1, 1968

By George C. Stone

WHEN George C. Stone, a Director of the Institute, and so well known to our Members in connection with the Institute's many activities was abroad in 1.919, he secured an interesting collection of these coins, which appeared in Zinc, a publication by the New Jersey Zinc Co. Regarding this collection of coin, Mr. Stone says: "During the war, all gold and most of the silver disappeared, making small change very scarce. As the French Government was fully occupied by the war, it allowed various Chambers of Commerce and other bodies to issue money, both paper and coins. Many of the latter were made of zinc, and I secured several while in Paris. We had all heard of the Belgian and German zinc coins, but I imagine few knew how many different kinds there were. The accompanying plates show both sides of those I got. I took all that the dealer had; but he said that there were a number of others in existence. The coins in the bottom line were issued by the Germans in Belgium during the war and all are still in common use. The first two in the next to the bottom line are German. All of the others were issued by Chambers of Commerce or corporations. A few have been nickel plated; these look and wear much better than the others. "Coins" made of pasteboard were also issued by similar bodies, also notes.

Jan 1, 1920