Search Documents

By Harlan W. Nelson, James B. Purdy

A study of data obtained during laboratory tests to determine the suitability of bituminous coals for use in residential underfeed stokers of the clinkering type has led to the following general conclusions: 1. Performance data obtained during the test furnish useful and practical information upon which to judge the performance of stoker coals. 2. Conclusions derived from the results of evaluation tests are in general agreement with use experience of the coals in the field. The method is of practical use in this regard. 3. Few direct relationships were found between data furnished by the evaluation test and determinations by standard laboratory tests. This is particularly true with regard to coke formation and clinker formation, two of the most important factors in determining the degree of satisfaction to be obtained in applications of the small underfeed stoker. It has not been the intention in this paper to prescribe this evaluation test as the best method for the evaluation of coals for use in residential stokers. That there are other test methods having similar objectives serves to point out the necessity for full-scale laboratory tests. At the present time, a standard test procedure for the evaluation of coals for use in residential stokers is not available. For the past several years a joint committee, appointed from the membership of the Residential Stoker Committee of Bitulninous Coal Research, Inc., and from the Engineer- ing and Research Committee of The Stoker Manufacturers Association, has been working to develop a standard procedure for testing and evaluating bituminous stoker coals. This procedure has been completed to the extent that it has been drawn up in tentative form. It is now planned to install the equipment in several laboratories and to run check tests, using portions of identical lots of coal, to determine the degree of reproducibility offered by the method. Completion of this standard test procedure should greatly facilitate the evaluation of coals for use in residential stokers. Acknowledgments The cooperation of coal operators sponsoring the coal evaluation tests, in granting permission to use data and results from their tests, is gratefully acknowledged. Acknowledgment is also made to Carroll F. Hardy, Chief Engineer, Appalachian Coals, Inc., for his interest and timely suggestions on the preparation of this paper. Special thanks are due to Ralph Sherman, Assistant Director, Battelle Memorial Institute, who was largely responsible for development of the evaluation procedure, for helpful suggestions and advice. References I. H. A. Sherman: The Evaluation of Coal for Use in Domestic Stokers. Univ. of Ill., Eng. Experiment Station, Circular No. 39 (1939). 2. . Q. Shotts: The Relation of Free- swelling Indexes to Other Characteristics of Some Alabama Domestic Stoker Coals. TP 2314, Coal Tech., (Feb. 1948); Trans. AIME (1948) 177, 502. 3. . J. Helfinstine and C. C. Boley: Correlation of Domestic Stoker Combustion with Laboratory Tests and Types of Fuels 11. Combustion Tests and Preparation Studies of Representative Illinois Coals. Ill. State Geol. Survey, Re1. of Zntlestigations No. 120 (19467 ) p. 35. DISCUSSION E. R. Kaiser*—AS a former fuel engineer assigned to residential stokers at Battelle, the writer has read with considerable interest the paper by Messrs. I'urdy and Nelson. It is gratifying to note that earlier test techniques have been developed and that criteria found important in the years 1935 to 1938 are still important in judging the performance of stoker coals for residential heating. The authors have plotted a number of the primary coal data singly against performance data of the stoker in an effort to establish relationships. Unfortunately, wide scattering of points usually resulted, which did not illustrate what experience generally indicates to be the case. For example, Fig 3 indicates almost no trend in the percentage of released ash converted to clinker with change in ash-softening temperature. Other factors, such as fuel bed temperatures and zones of heat release must have influenced the results. In the present state of our knowledge, we cannot explain all of the reasons why suitable stoker coals perform satisfactorily, nor why one satisfactory coal may be better than another. It would therefore

Jan 1, 1950

By J. L. Bruce

For a number of years, from an economic standpoint, the ventilation of the Colorado mine of the Davis-Daly Copper Co. has been a difficult problem. The development through the main hoisting shaft was pursued for a number of years and to a depth of about 2500 ft.( 762 m.)before large bodies of good commercial ore were opened up. This lack of early success in exploration restricted expenditures for ventilation, with the result that the present orebodies were opened up at a depth of 2500 ft., and in country rock f relatively high temperature, without adequate means f supplying the development faces and the stopes with cool or fresh air of low humidity and suitable velocity. During the progress of development, two or three connections were made at higher levels with the workings of adjoining operations, but these were of a makeshift and unsatisfactory character and afforded no means for carrying downcast air from the surface, in anything approaching a direct course, to the working faces. During the latter part of 1917, arrangements were made with. the Anaconda Copper Mining Co., whereby, during the year 1918 and the early part f the year 1919, a crosscut was driven eastwards on the 2500-ft. level of the Colorado shaft and connection was made by means f an up-raise of approximately 200 ft. to a crosscut driven westwards from the 2800-ft. level of the Belmont mine, this crosscut at the top of the raise being driven at Davis-Daly expense by the Anaconda Copper Mining Co. This connection, in conjunction with a No. 11 Sirocco fan installed near the Colorado shaft, provided the Colorado mine with a maximum of approximately 30,000 cu. ft. per min. of relatively fresh air, most of which came in a fairly direct route from the downcast Belmont shaft through the No. 11 fan to the 2500-ft. level stopes. After passing through these stopes and the stopes of overlying levels, it passed through the main crosscuts on higher levels back to the Colorado shaft, which provided the upcast for this current of air. The improvement

Jan 9, 1921

By J. L. Rodda, R. L. Wilcox, E. C. Truesdale

IN recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on .the current equilibrium diagrams.. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I. of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part II of the paper the attempt is made to review all of the published work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data

Jan 1, 1935

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986

By Michael A. Toole, O&apos

INTRODUCTION The tremendous capital investment required to produce a low grade ore deposit demands a reliable answer to the question: "How much does it cost to drill a well to produce the uranium that geologists have indicated is there in the ground?" However, you will find the answers given will be many and varied, depending on whether they come from the operating company, the drilling contractor, a geologist, a reservoir engineer, purchasing agent, or whoever. Each generally considers only a limited area of the total operation. The operating company usually depends upon the drilling contractors, service companies, and consultants to supply expertise. Because it is often difficult to see the "whole picture" or even to agree upon what the "whole picture" is, planning a well program and its costs is often done piecemeal. Frequently, costs "saved" in one area of the program are needlessly spent in another, because the effect of one area upon the other was overlooked. Since the drilling fluid is such an influential part of the drilling program, it should be given utmost consideration when planning the overall program. As W. D. Lacabanne wrote in 1954: "The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig.... should benefit by the incorporation of mud fluids in the drilling scheme." And G. R. Gray mentions that "The driller recognizes the drilling fluid as one of the useful tools available to solve drilling problems." However, in minerals drilling, only in recent years has the drilling fluid been considered as more than a tool to get through special problem areas. Although there are many similarities between drilling for oil and gas and drilling for minerals, the differences in the drilling equipment used justifies designing specific fluids for the minerals drilling industry. NL Baroid/NL Industries, Inc. has been a leader in introducing such fluids and in providing technical know-how to the minerals drilling industry. The purpose of this paper is: (1) to discuss the selection of drilling fluids to meet specific drilling conditions during both exploration and production and (2) to show the interrelationship among factors present in the exploration and production phases that influence total well costs. DRILLING FLUIDS FOR DRILLING PROBLEMS The drilling fluid is a tool that can be used to improve drilling performance by improving hole cutting, cleaning, stability, and formation productivity. Properly formulated and maintained drilling fluids enable the drilling operation to be carried out with increased efficiency and lower total (overall) costs. However, it should be noted that not all drilling problems can be solved by even the most carefully prepared and maintained drilling fluids. Of the many possible drilling problems encountered in a well before reaching target depth, this paper will discuss only those most likely to be present in the shallow [61 to 610 m (200 to 2000 ft)] drilling operations in South Texas. LOST CIRCULATION Loss of circulation is the most common problem encountered in drilling. Because the losses occur under varied conditions, it is often difficult to determine the exact causes. "Lost circulation" or "lost returns" means the partial or complete loss of drilling fluid to voids in the formation. "Loss of water" while drilling with water may take place into any permeable section and should be distinguished from "water loss" or filtration of fluid through the filter cake of mud solids laid down on a permeable formation. "Loss of water" can frequently be stopped by the addition of colloidal sized clay particles such as high yield bentonites, whereas "water loss" may be controlled with organic polymers. Subsurface conditions that lead to loss of circulation can be classified as: (1) natural fractures, (2) induced fractures, (3) unconsolidated or highly permeable formations (loose gravel), and (4) cavernous formations (crevices and channels). Loss of circulation may occur whenever the borehole pressure exceeds the formation pressure. The greater the differential pressure, the more likely it is that circulation may be lost. To stop loss of whole mud, voids must be bridged so that a filter cake can be laid down on the permeable section. The plugging material must be of the proper size and shape to offer greater resistance to the fluid flow around it than the flow up the annulus. A plugging composition that satisfies these requirements may not be able to be handled by the small rig pump available.

Jan 1, 1979

JOHN.B. HASTINGS, Los Angeles, Cal. (written discussion).-This paper reminds me that when I had an option on a Nevada mine, where the only orebodies assayed $4 gold, I went to San Francisco to learn the cost of putting broken ore in a 25-ft, vein on the mine cars, and sought Mr. Alfred Wartenweiler, who said "There is not a mine in California that can tell what it costs to move ore in the stopes." When building small mills in the mountains, and with only 30 or 40 employees, by entering in a log at night the work performed by each man, I have been able to plot the costs with the accuracy shown in this paper, and very good discipline it is. Cost of new construction and repairs is carefully kept by most companies, and is compiled after completion; probably the outlay of labor and material in pieces of work sufficiently important to call for blueprints is estimated beforehand, but numberless odd jobs of construction and repairs are so itemized. . Might it not be worth while, at a large plant, to have these smaller daily tasks described in advance in a central repair office, and then let inspectors look over the job, report time and material needed, and enter it in sufficient detail in proper ledgers, the men then being sent to accomplish it, and reporting when finished? The forecasts would soon be made quickly and correctly and would give the head mechanic, carpenter, and electrician easy supervision of their men, and the results could be seen at a glance by the managers.

Jan 4, 1918

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By Edward A. Loria

A SERIES of papers on the study of austenite grain A size in cast steels has been published recently.'" These studies show that in the as-cast state, the austenite grains are quite large, for they form as the steel freezes at a very high temperature, but a simple reheating above the critical range produces a new set of austenite grains which, in many instances, is finer than ASTM grain sire No. 8. Furthermore, there is no apparent relationship between as-cast austenite grain size and subsequent grain size produced by heat treatment. The as-cast austenite grain size can be determined easily in plain carbon and low alloy steels which produce a continuous grain boundary f errite envelope in the as-cast structure. In the case of cast steels whose alloy content produces greater hardenability and suppresses the proeutectoid ferrite transforma-

Jan 1, 1952

By John Birkinbine

Secretary's Note.—In printing this paper in the present volume, the figures given in the pamphlet edition have been brought more nearly up to date, the product of 1899 being in many instances inserted. Iron-Ore Resources. In a paper presented to the Institute in 1897,* I discussed the iron-resources of the United States as then developed, calling attention to some principal sources upon which other countries depended. The following statement will give a general idea of the amounts, as compiled from the latest official records, of ores won, and metal produced, in the nations which are important contributors to the world's output. Unfortunately these are not all contemporaneous, since in some countries the statistics do not appear until after one or more years. The statement covers not only pig-iron and iron-ore, but also manganese-ore —the manganese mined being principally used in the production of spiegeleisen or ferro-manganese, and these alloys being generally included in the pig-iron output. Table I, which epitomizes the present situation, shows respectively the countries and the quantities of iron-ore and man-

Jan 1, 1901

By AIME AIME

FOR constructive research in copper and brass and other non-ferrous metals and their alloys, and his contributions to the establishment of the present accepted high standards of quality William H. Bassett, technical superintendent and metallurgist of the American Brass Co., has been awarded the James Douglas Gold Medal for 1925. Mr. Bassett was born in New Bedford, Mass., on March 7, 1868, and was graduated in chemistry at the - Massachusetts Institute of Technology in 1891. In the same year he went to Pope's Island Manufacturing Co., at New Bedford, as chemist where he remained until 1895, where he became a teacher in chemistry at the Swain Free School, which position he retained until 1900. He then became chemist for the New Jersey Zinc Co., at Newark N. J., and in 1902 went to the Coe Brass branch at Torrington, Conn., as Chemist. In 1903 he became chief chemist and metallurgist and since 1912 has been technical superintendent and metallurgist of the American Brass Co., with head- quarters at Waterbury, Conn.

Jan 1, 1924

By Frederic Benard

The electrolytic copper refinery at Copper Cliff, Ont., is operated by the Ontario Refining Co., Ltd. The associated companies behind the enterprise are the International Nickel Co. of Canada, Ltd.; The American Metal Co.; The Consolidated Mining & Smelting Co. of Canada, Ltd.; and Ventures, Ltd. The plant was the outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as closely as possible. The refinery is near the intersection of the Sault Ste. Marie to Sudbury highway and the Canadian Pacific Railway. It is about one mile south of The International Nickel Company's smelter at Copper Cliff. The standard-gage track systems of the refinery and of the smelter are connected by a standard-gage timber railroad trestle that crosses the railway and the highway by means of steel girder spans. The Canadian National Railway has access to the plant by means of this trestle and the nickel company's tracks, so that the refinery has connections with both the Canadian Pacific and the Canadian National railways, as well as a direct connection with The International Nickel Company's smelter, from which the bulk of the copper to be refined is hauled by the latter's electric locomotives. Buildings The refinery (Fig. 1) covers approximately 60 acres, enclosed by an unscalable chain-link fence. The main buildings have a content of 23,000,000 cu. ft., with a total roof area of approximately 600,000 sq. ft. and near them are the substation, cooling pond and main standard-gage track system (Fig. 2). A ladder track for car storage extends 1200 ft. south of the coal-pulverizer tracks and the scale house is on this spur. The intake and pumphouse for fresh water supply are at Kelly Lake, about 3000 ft. south of the plant. Owing to the severity of the winters, when temperatures of from 20" to 40' below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were

Jan 1, 1934

By C. W. Waidner

THE standard scale of temperature that it is attempted to realize in practice is the centigrade thermodynamic scale, as defined by Kelvin about the middle of the last century. This scale would be exactly realized with a perfect1 gas in an ideal gas thermometer, and is closely realized with the more permanent gases. From the departure of certain properties of these gases from those of a perfect gas, it is possible to deduce the amount of the departure of the temperature scales, defined by their use, from the thermodynamic scale. In nearly all the precise experimental work done during the latter part of the last century, it was necessary for the experimenter to establish his own gas-thermometer scale, and the labor involved in this was often greater than that involved in the prime object of the experimental work undertaken. The experimental difficulties involved in gas thermometry led to the establishment of temperature scales differing from one another by amounts considerably greater than could be accounted for by the differences in the properties of the gases used. Results were, therefore, expressed in terms of somewhat different temperature scales, snaking correlation of such results difficult and uncertain.

Jan 9, 1919

[ ]

Jan 1, 1938

By Verne C. Fryklund, S. Warren Hobbs

The Coeur d'Alene district in the panhandle of Idaho is one of the major lead-zinc-silver producing areas in the world. The value of recorded production to date has exceeded $2 billion. Country rock comprises six formations of the fine-grained, highly siliceous, and slightly metamorphosed Precambrian Belt Series. Small stocks of monzonitic rocks and several varieties of dikes intrude the sediments. The district is at the intersection of a north trending major anticlinal uplift and the west northwest-trending Lewis and Clark line of which the Osburn fault is the dominant feature. The district structure is complicated and comprises folds, some of which are overturned, and a complex of faults of diverse ages and directions of movement. Late Cretaceous stocks but are also probably Cretaceous in age. The productive veins are localized within a series of 12 subparallel, straight mineral belts that trend approximately N65°W and that appear to be controlled by deep fractures in the basement rocks. The mineral belts are in two groups, separated by 15 miles of post-mineralization movement on the Osburn fault. Veins and ore shoots are variously disposed within each mineral belt. Many crop out at the surface, but others apex several thousand feet beneath it. Local controls that influence the position of ore shoots within the mineral belts include the brittle character of host rock attitude of bedding relative to the mineralized fracture, and the amount and direction of movement on faults. Depth appears to have had little effect on the occurrence or type of ore. Ore occurs in a series of steeply dipping replacement veins of relatively simple mineralogy. Six periods of mineralization, ranging from Precambrian to Tertiary in age, are recognized. The productive galena sphalerite-bearing and tetrahedrite-bearing veins-of the main period of mineralization-are younger than the

Jan 1, 1968

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By NILS DANIELSEN

THE name of Swedish charcoal iron will probably bring to the memory of many old consumers an extremely tough and ductile iron which was formerly used in considerable quantities for common blacksmith purposes. To-day very little of this iron goes to such kind of work. Swedish charcoal iron is merely a speciality which is chosen whenever its remark¬able properties can be utilized. By giving a rough sketch of the manufacturing process of Swedish charcoal iron, the character of the iron, its weak as well as its strong points will more easily be understood. Swedish charcoal iron is a wrought iron also known in the United States under the name of Norway iron and Swedish Lancashire iron. The name Norway iron seems to have been attached to the product for the reason that in the earlier days it was generally brought into the States by Norwegian ships. However no iron of this kind is now made in Norway. The reason for the name Swedish Lancashire iron is that the manufac¬turing process emanated from Lancashier in England, the method being generally adopted in Sweden in the years 1831-1850. Today this iron is, with the exception of one plant in the United States, made in no place in the world outside of Sweden.

Jan 1, 1924