Search Documents

By W. H. Kantner

In this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change subsidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the surface to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the cast and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody—which is on the northwest side—is 600 ft. 'southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934

By Peter J. Lean

The introduction oE computer control in the grinding circuit of the New Broken Hill Consolidated Limited concentrator in the early 1970's gave smoother operation at optimum performance. The ore feedrate and water additions to the grinding circuit were controlled to operate each of the ball mill/ rake classifier grinding units at the upper limit of the circulating load while classifier overflow density was maintained to give a product size and pulp density suitable for flotation. An incremental expansion of the concentrator in 1981-82 included the installation of hydrocyclones in closed circuit with three of the four ball mills. Without the rake classifiers in circuit the previous control strategy could not be used and the complex interaction of hydrocyclone performance characteristics when classifying coarse grained sulphide ore resulted in the over-grinding of the lead mineral galena. Testwork aimed at optimising grinding circuit performance recognised the enhanced tendency of higher specific gravity minerals to report to the cyclone underflow. The data has been evaluated on an individual mineral basis and then used to develop a model For grinding circuit control. The development of the model which uses inputs of ore feedrate, metal content of the Feed and slurry density of the cyclone overflow to predict the size of the minerals in the grinding circuit product is described and model predictions are compared with plant performance.

Jan 1, 1984

By Gary E. McIntosh

This paper will discuss a US Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater system in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring shallow groundwater systems in the basin; (2) monitoring the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems; and (3) development of a regional groundwater simulation model, with appurtenant subroutines to determine local effects.

Jan 4, 1979

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) IN vol. 33 of the Proceedings of the Institution of Civil Engineers, London (part 2, for 1870-71), may be found a statement of the cost of two blast furnaces, together with a somewhat detailed description. The attempt will be made in this note to restate these items of cost, so that the information may be rendered perhaps more accessible to our members than in its present place of record, and also in order that the items may be more intelligibly compared among themselves, or with similar items in other cases.

Jan 1, 1878

By J. W. Whitlow, P. K. Theobald, W. C. Overstreet

Monazite placers in a region of the Carolinas ex- in 1951-1954 by the USGS are estimated to contain at least 53,000 short tons of thorium and 4600 short tons of uranium. None of these deposits is being mined. The 5200-sq mile area investigated extends northeast along the western Piedmont from the Savannah River in South Carolina to the Catawba River in North Carolina. Much of the region is 700 to 1100 ft above sea level. Gentle hills and broad interfluves give a local relief of 100 to 200 ft. This increases to 1700 ft at the west margin of the area where the east flank of the Blue Ridge is approached in South Carolina and the South Mts. are entered in North Carolina. This report is restricted to placers in the Piedmont. Monazite deposits in the Blue Ridge and coastal plain were not covered by the investigation. Monazite Mining in the Carolina Piedmont: Discovered in 1879 by W. E. Hidden,' the monazite placers in the Carolina Piedmont were first mined in 1886. The area was a major world source for thorium and the lanthanides until 1895, when Brazilian monazite entered the trade. Total output from the Carolina Piedmont has been nearly 5500 tons of monazite,2 but the placers have been idle since 1911, except for 48 tons produced between 1915 and 1917. Monazite mining was revived in the Carolinas in 1954 when a dredge operated by the Heavy Minerals CO. opened a fluviatile placer along Horse Creek in the coastal plain near Aiken, S. C. Geology and Mineralogy: Two recent papers",' have described the geology of the monazite placer district in the Piedmont between the Savannah and Catawba rivers; the general geology of the region has been reviewed by P. B. King.' These reports show that the placers are in locally derived alluvial sediments that cover the floors of shallow, narrow valleys in an area underlain by monazite-

Jan 1, 1960

By Robert H. Weber

INCREASING acceptance of perlite products, chiefly in the fields of lightweight structural aggregates and thermal and acoustic insulation, has led to expanding market demands that have encouraged many new producers to enter the field. In some instances, however, the failure of these producers to anticipate the variable response of perlite to conventional processing methods has led to difficulty in establishing an economical flowsheet by which a predictable specification product could be obtained. It is not the writer's intent to provide a solution to these problems, but rather to summarize their nature. It is to be hoped that members of the industry who have hurdled some of these obstacles will document solutions arising from their experience. In this treatment the term perlite will not be restricted to the petrographic definition but will apply to all volcanic glasses. Expansible obsidians and pitchstones are accordingly included in this broader industrial classification. Chemical Properties: Although perlite has been reported to range in composition from that of rhyolite to that of andesite, it is probable that most of the glasses have the composition of rhyolite. When recalculated to an anhydrous basis, the five analyzed glasses from New Mexico, representing five distinct physical types from widely separated deposits, show an amazingly uniform oxide composition. Water content is the only major compositional variable; total water ranges from a low of 0.37 pct (non-expansible obsidian) to a high of 8.95 pct (expansible pitchstone). The wide range in expansion characteristics exhibited by these samples cannot be related to significant variations in the composition of the nonvolatile fraction and has been only partially correlated with variations in water content.

Jan 1, 1956

By Dorsey Hager

One of the most interesting fields in North America was discovered, early in 1922, near the towns of Sunburst and Kevin, Toole County, Mont. This field produces oil from the Jurassic beds, which heretofore have been of but little importance as oil producers, and promses to be the

Jan 1, 1923

By Dorsey Hager

One of the most interesting fields in North America was discovered, early in 1922, near the towns of Sunburst and Kevin, Toole County, Mont. This field produces oil from the Jurassic beds, which heretofore have been of but little importance as oil producers, and promses to be the

Jan 1, 1923

By D. D. Lambert, E. C. Simmons

Rare earth element (REE) analyses of cumulus plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma cannot be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data are more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE-bearing sulfides of the J-M Reef are associated with such a reappearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultra- mafic zone of the complex.

Jan 1, 1984

By K. I. Savage, L. G. Austin, S. C. Sun

The comminution environment - the physical, chemical, and solid state - was studied for silicon carbide ground wet in a laboratory vibratory mill. The relative importance of these variables on the grinding rate of producing a material 50% passing 5µ from a powder feed of 50% passing 19µ was established.

Jan 1, 1975

By Robert Sisselman

Dramatic changes have been effected since 1955 in the mode of iron ore shipments within the U.S. In 1955, less than one percent of ore consumed in domestic blast furnaces-approximately 125 million long tons-consisted of pellets. Five years later, in 1960, some 94.8 million tons of ore were consumed, 14% in the form of pellets. Projections for 1980 reinforce confidence in this most economic of blast furnace feeds, and set U.S. pellet consumption at 151.2 million tons. In the last decade, pellets caught fire in other countries. By 1969, world production reached 96 million tons. This compares strikingly with present world output of 154 million tons.

Jan 9, 1973

By Laurence W. Casteel

Indian Creek Mine, newest of the St. Joseph Lead Co. properties, is located in southeast Missouri on the flanks of a buried porphyry ridge. Here the orebodies are very irregular in size and shape and have a regional pitch of about 15°, which may vary locally from 0 to 90°. To maintain an economical grade of ore, selective mining is imperative. The room and casual pillar method is employed with 20-ft diam pillars 35 ft apart where possible. Stopes vary in height from 10 to 55 ft. All are too small to supply a loading unit continuously.

Dec 1, 1956

Howland Bancroft (A Modern Approach To Foreign Mineral Development, P 666) was born in Denver, Colo and attended the University of Colorado, University of Michigan and received a B S and B A degree From 1907 to 1912 he was with U S Geological Survey In 1911 he was involved in study of mining resources of Peru Mr Bancroft resigned from Federal Survey and opened offices as consulting mining geologist in Denver in 1912 From 1919 to 1920 he was a consulting engineer in San Francisco He was manager of Sinclair Panama Oil Corp in Panama City in 1920 From 1921 to 1923 he was vice president and managing director of same corporation He did independent examinations in Western states and an exploration trip through Turkey in Asia from 1924 to 1925 Mr Bancroft was vice president and general manager of Lago Petroleum Corp in charge of operations in Venezuela Mr Bancroft has spent time in 34 different countries in the world and in a number of different Latin American States, Europe, Asia Minor and Africa

Jan 1, 1952

By A. Eilers

THE telluride of gold and silver, the " Tellurgold-silver" of Hausmann, and " Petzite" of other mineralogists, has been found in so few localities, that a late discovery of the mineral in a new locality may not be uninteresbing. So far this mineral has been found in Europe only in a few mines in Transylvania, and in Hungary; and in the United States in the Stanislaus Mine, in Calaveras County, California, in the Golden Rule Mine, Tuolumne County, California, and in a mine in Montana, the precise locality of which I have forgot, ten. The new locality referred to is at the Red Cloud Mine, Gold Hill District, Boulder County, Colorado.

W: 0. HOTCHKISS, Madison, Wis. (written discussion*).-Mr. George's paper on. "The Wisconsin Zinc District" is a very complete and clear description, which it is a pleasure to read. His discussion of the origin of the ores is the least satisfactory part, and Mr. George correctly states present knowledge when he begins his paragraph on a origin with the words "the general supposition is, etc." There is still much to be learned regarding the details of the processes by which the ores have reached their present situation. In this the Wisconsin district differs not at all from other mining districts. It is my hope that Mr. George and others, equally clear-thinking, who are in close touch with these operations will be able at an early date to give us more information on this subject.

Jan 3, 1918

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese: they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way: there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution arrived.

Jan 6, 1976

By Clinton M. Young

The experiments herein described were carried on in 1908-9 by- the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coalmines, a subject which is engaging the attention of numerous investigators. An unusual number of serious disasters has directed to the subject a study which discloses the disquieting fact that, in the United States, the ratio of lives lost per ton of coal mined has been 011 the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and a very great increase in the amount of explosive used. This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle West it is not now uncommon for a miner to use six kegs (150 lb.) of black powder in a " pay" of two weeks, while within the memory of men still active, one keg (25 Ib.) would last two men for a " pay." So great has the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject of explosions in coalmines has led to the belief that the use of large quantities of explosives, in some cases by slightly-trained men, had riot been

Jan 1, 1911

By H. S. Hanna, C. Rampacek

The problems and limitations encountered in the Physical beneficiation of the Appalachian Red Iron Ores are discussed. Two major problems are identified - the high phosphorus content and the fine dissemination or encapsulation of mineral impurities in the iron-bearing minerals. A process that combined extreme fine grinding techniques with magnetizing roasting or flotation-separation methods is suggested. By these methods, concentrates assaying 60-61 % Fe, exceeding the widely accepted upper limit of 56% Fe set for these ores, were produced with 75-90% iron recovery. Moreover, it was shown that the phosphorus content of these concentrates could be reduced from 0.25% to 0.03% phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1983

By Charles R. Keyes

In the dry regions of the globe many silver-deposits display certain remarkable features, which at the same time are so totally unlike anything met with among ore-bodies elsewhere that they hare long presented exceptional dificulties, not only to a satisfactory explanation of their origin, but to economical milling. A most striking peculiarity of these ores is the haloid character of many of their bonanzas. To this fact more than to any other may be ascribed most of the unusual uncertainties of mining-operations in desert countries—the marvelous local richness of the ores under certain conditions and the often abrupt transition to utter poverty; the inadequacy of ordinary prospecting customs and the constant devising of new exploratory methods; the unaccountable losses in smelting and the continual change in treatment-practice. For these anomalies certain climatic conditions seem to be chiefly responsible.

Jan 1, 1912

By J. D. H. Strickland, K. J. Jackson

IN previous papers' ' details were given of the constructlon and use of an apparatus to study the rate of chlorine consumption and the rate of sul- fate and sulfur production when dilute aqueous chlorine solutions were allowed to react with pyrite and galena in acid solutions at or near room temperature. The reaction with pyrite was very rapid, and hence entirely transport-controlled in its kinetics, and produced only ferric and sulfate ions. The behavior of galena was much more complex and was studied in some detail. Sulfur monochloride could be detected as a reaction product and both

Jan 1, 1959