Search Documents

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the, limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By Franz R. Dykstra, R. F. Tatnall

A ferroalloy is defined as: "An alloy of iron with some element other than carbon used as a vehicle for introducing such an element into the manufacture of steel. The element may alloy with the steel by solution or, as the carbide, -neutralize the harmful impurities, by combining with them and separating from the steel as flux or slag before solidification."a The most commonly used ferroalloys are: ferromanganese, ferrochrome, ferrosilicon, ferrovanadium, ferromolybdenum, ferronickel, ferrotungsten, ferrocolumbium, and ferrophosphorus. Concern here is with the sources and markets of the major metallic alloying elements. The discussion is further restricted to those - ferroalloy ores, the principal use of which is in the production of steel. Phosphorus, silicon, and tungsten, for example, are ferroalloys of some economic significance, but other uses dwarf their alloying applications. Thus, this discussion will deal with the ores of managanese, chromium, nickel, molybdenum, vanadium, and columbium. As shown in Table 14.1B.1 ferroalloys serve to- facilitate processing and impart to the finished steel such characteristics as tensile strength, ductility, low-temperature impact, hardenability, high-temperature strength, corrosion resistance, toughness, and abrasion resistance. In the steel-making process, ferroalloys may be added in the charge, in the molten bath near the end of the finishing period, in the ladle, or in the molds. Timing of the addition depends on the effect of the addition on the temperature of the molten metal, the formation and elimination of reaction products, and the protection of subsequent additions from oxidation. MANGANESE General Approximately 95% of the manganese ore sold is consumed by the steel industry, either as ferromanganese or as manganese metal. Manganese is the universal alloy, without which good steel cannot be made. It serves as a scavenger, removing phosphorus, sulfur and, to a degree, oxygen from the melt. As an alloying material it makes steel hard, tough, and resistant to wear. Approximately 6 kg of manganese is required for every ton of common steel produced by United States steelmaking practice. The remaining 5 % of the manganese ore consumed consists of special or so-called "chemical" ores, including high-grade pyrolusite ores, electrochemically reactive "battery ores," and a number of special varieties, as well as those otherwise regarded as "metallurgical ores."

Jan 1, 1976

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0&apos;815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By Gerald A. Munson, Fremont F. Clarke

During recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodumene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S.

Nov 1, 1955

By Iichiro Omori

THE Mabuki process, a Japanese hearth process for the treatment of matte, uses the same princi-ple as the Bessemer steel process. The only difference between the two is that in the Mabuki proc-ess a hearth furnace, not a converter, is used. Though the hearth is not as good as the converter, the first cost is very low and the capacity is compara-tively small; so the process is most suitable for smelters FIG. 1.-PLAN AND SECTION OF HEARTH. having a small production. To construct the hearth, an excavation, 6 ft. in each dimension, is made in the ground and a drainage channel is dug at the bottom. Then all side walls are faced with stone or slag brick and the cavity is filled with fireclay or brasque, except the hearth at the top.

Jan 9, 1922

By Murray Kaufman

Using en; 41 for a base alloy, 15 modifications were made in sheet form. The elements Al, Ti, C, Mo, Co, and Cb were varied. The effects on the phases formed and their temperature dependence, the aging characteristics, tensile and stress-rup- ture properties, and weld cracking were determined. The A1-Ti content and balance is the most important factor influencing the major sCrengthening phases [Ni,Ti and Ni,(Al, Ti)] and, consequently, mechanical properties. THE mechanical properties, fabricating and joining characteristics, dimensional stability, and so forth, of alloys containing secondary phases are largely determined by the phases present, their distribution, and their temperature dependence. The phases in the basic ternary and quaternary Ni-Cr-Al-Ti combina- tions have been investigated thoroughly.&apos;* The phase behavior of many commercial nickel-base alloys has been determined also. In some cases, for example U500, 5 the effect on mechanical properties has been found. However, little systematic work has been done to clarify the action of each of the important alloying elements in controlling the phases formed in complex commercial alloys and their behavior. The effect of molybdenum on the carbides formed in M252 was investigated by Beattie and verSnyder.6 Application of the results provided by that work

Jan 1, 1963

By M. B. Yung

The Fu Chuan district lies near the eastern boundary of Kwang Si province in Southern China and is connected with the coast by the West river and its branches.

Jan 1, 1915

By L. H. Levenson, Charles S. Barrett

Numerous determinations1-&apos; of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By Charles S. Barrett, L. H. Levenson

Numerous determinations1-&apos; of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By D. W. Smith, C. H. Mathewson

In a series of papers published recently,&apos; R. F. Mehl and associates have studied the characteristics of form and orientation of many segregate structures and have found diversified conditions which can be explained only by postulating some specific kind of cooperative mechanism permitting the matrix lattice in some favorable region to transform into the segregate lattice in an adaptable region presenting a geometrically similar arrangement of atoms. We have collected the published data on crystallographic relationships of this sort, chiefly derived from Mehl&apos;s work, in Table 1. It is evident at once that the crystal structure of the matrix does not uniquely determine the location of the plate structures or other forms assumed by the segregate. Thus, the first seven items in the table represent precipitation of platelike forms from a matrix of face-centered cubic structure, but these plates are found stratified along planes of form {1111, {loo), {110) or another unidentified form, depending upon specific conditions involving the nature and concentration of the segregating substance. Again, in a matrix of body-centered cubic structure, plates, needles or stars have been found and the favored inner surface of segregation may be a plane of form (110), (112), {210), or indeed a surface without crystallographic indices defining a bundle of close-packed lattice lines (strings of atoms) taken more or less at random. Such a surface might be formed ideally by revolving one of these parallel strings of atoms around another as an axis. Hanemann and Schroder2 recently discussed these questions, principally with relation to original conceptions concerning the process of

Jan 1, 1932

By Conrad E. Hesse

To increase the durability of paint exposed to the weather, it is necessary to protect the oil with a substance that is itself unaffected by the elements. The so-called " metallic " paints, containing ochre,

Jan 1, 1891

By John W. Rushton

What role does maintenance play in the design of a new mineral processing facility? Consider the fact that most new plants never reach design capacity the first year-or the second, third, or fourth years. The fact is, according to data collected from several plants which have started up in the last ten years, mill throughput and equipment availability doesn&apos;t peak, on the average, until the fifth year.

Jan 3, 1978

By Earl C. Herkenhoff

Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95% of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978. "Separation of Bitumen from Dry Tar Sands," was the first blockbuster. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high &lids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95OC (203°F) in a 0.3 m solution of sodium carbonate-about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60.62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let&apos;s mine heavy oil and tar sands.

Jan 1, 1983

By Klaus Emicke

The paper describes the lead refining process operated at Norddeutsche Affinerie (N.A.). Incoming materials are different grades of lead with varying percentages of impurities: Cu, Te, As, Sn, Sb, Bi, precious metals. The facilities are designed for charge-wise operation. After drossing, generally Te, As, Sn and Sb are removed substantially by the Harris Refining Process using fused NaOH. A certain selectivity during refining is achieved by controlled addition of NaNO3. Another refining step is decopperizing by means of elemental sulfur. Complete separation of Te, As, Sn and Sb is accomplished by chemical methods in a leaching plant. A Howard Press is used in the Parkes Process for desilverizing. After vacuum dezinking in kettle, Bi is removed, if required, by means of Ca and Mg. In an end refining step Ca, Mg and Zn are removed by having the lead melt treated with NaOH and NaN03. The refined lead as such, or in the form of special alloys, is cast by an ingot casting machine into 50-kg ingots. Zinc which is used as a precipitant in the Parkes Process is recovered by distillation from the high grade Ag-Zn-Pb crystals in Faber du Faur retorts while the Pb/Ag alloy is fed to the cupellation furnace. Ca and Mg are removed from the Ca-Mg-Bi crystals formed in the course of Bi removal, and the Bi-bearing lead is cast into anodes. The electrolytic lead refining facilities at N.A. are operated largely for the purpose of separating Pb and Bi. These facilities are also used particularly for the refining of Bi-bearing lead which had gone through the above process, but from which Bi has not been removed by Ca and Mg.

Jan 1, 1970

By Moshe Sheinkin, Douglas E. Julin

Large tonnage operations face many problems in adequately planning ahead for future years production. In order to maintain desired levels of production, such problems as source of tonnage, man- power and equipment requirements, tailings disposal and water requirements must be anticipated. Of course, before any of these problems can be analyzed, daily tonnage requirements and its source must be determined. Looking ahead for one year or even two or three is usually not sufficient time to adequately prepare an area for production. Because of the sequence of mining and the multilevel nature of the 42,000 tpd Climax mine in Colorado long-range planning must be on a ten-year basis. By using a ten-year base, adequate time is allowed to gain access and prepare a new level for production. Usually eight years will be required for this phase of the initial mine preparation. Once production has been started on a level and access to the area is available, three years is usually sufficient to prepare a new block for production as long as it follows in the normal sequence of mining.

Jan 4, 1967

By Charles Catlett

My attention having been called several years ago to the possibility of increasing the yield of coke per ton of coal, as obtained in certain bee-hive ovens, I called the attention of the Institute to the matter at the New York meeting in 1899. I have had occasion since to witness the indifference with which this matter is ordinarily considered, and, on the other hand, the marked improvement which comes from even a most perfunctory effort in that direction; and I am almost tempted to say that nothing in connection with the coking of coal is at present so important. There are other factors, which are fundamental and necessary; but they have been considered already ; while the question of yield is, as a rule, absolutely ignored, or some figure is taken as the result of a special burning of one or two ovens, and the assumption is made that the whole battery is yielding at that rate. The uncertainty of this assumption I may illustrate by saying that, in my own observation, the burning of a single oven in a battery frequently gives, by actual weight, as much as 69 or 70 per cent. of merchantable coke, while the battery as a whole was yielding only an average of 63 per cent. Only from careful records, checked at least once a month, of the weight of the coal going to the ovens and the weight of coke produced, can any correct idea of the actual yield be gained, or methods be modified so as to produce good results; yet, as a rule, the crudest estimates are usually the only available data. In many cases there are reasons for this loose practice. The coal is mined by measurement; the payment for drawing the ovens is in proportion to the amount of cod which goes to them; and, not uncommonly, the royalty is so much a ton of coke, not of coal. The mine-manager is tempted to increase the volume of coal mined which is paid for as a ton, and to do the same thing in charging the ovens. Nor does he

Jan 1, 1903

By G. Richard Dreese, Harold L. Bryant

The coal mining industry has had a long history of successfully externalizing part of its costs. Thus the private or internal costs of coal mining have been minimized and the social or external costs have been ignored. The externalized costs have largely taken the form of water pollution from acid mine drainage and sedimentation of stream channels from eroding spoil banks and gob piles. The environmental problems created by strip mining are very conspicuous, so the public demand for legisla-

Jan 1, 1975

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world&apos;s produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world&apos;s demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world&apos;s barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975