Search Documents

By John B. Pearse

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway Managers determined on and have long applied a test of 1000 pounds falling 101 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails from our most reliable makers, break under a 6 foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 13 1/2 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent, of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. In England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariably

Jan 1, 1873

By R. J. Marcotte, C. T. Eddy, R. J. Smith

The objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. Cast Steels The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition—all of which is summarized in Table I. The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

J. S. UNGER,* Pittsburg, Pa, . (written discussion?).-The author of the paper has given an excellent description of the appliances used to cool parts of an open-hearth furnace, and some of the reasons why the refractories fail in service. Personally, I favor water-cooling, but to a limited degree. At one time I advocated more universal cooling than is now practised, but believe I must change my mind. Water-cooled, thin-lined blast furnaces have not proved as satisfactory as anticipated. While this may retard the building of many such furnaces, it will not prevent the use of regular tuyere- and bosh-cooling appliances. Water-cooling any furnace may be easily carried to the extreme. In an open-hearth furnace, excessive port or roof cooling, or cooling the working floors may preserve the lines of the furnace, lower the cost of refractories, acid to the comfort of the workmen, and necessitate fewer shutdowns for repairs, but it may not be good economy on account of the high first cost, the cost of cooling water, maintenance of cooling appliances, and the immediate reflection in a higher fuel cost. The question becomes a financial one, and is answered by using water-cooling devices up to the point at which they cease to show true economies. Open-hearth furnace bulkheads, roofs, and ports fail rapidly in about the order named. If they could be made to last indefinitely by water-cooling, the furnace would still have to be shut clown periodically for cleaning the slag pockets, regenerator chambers, and flues. Extra, or spare, pockets and regenerator chambers have been advocated to permit of continuous operation, but the space required, the cost of installation, and the fuel required to initially heat such cold chambers will largely prevent their adoption. Some particular fuels, as high-ash powdered coal, require frequent stoppages for cleaning, but for this particular fuel a special provision can' be made.

Jan 5, 1919

The Inspiration ore body was discovered in 1904, but a 50 -ton mill which was installed to treat the disseminated copper ore promptly failed. The original Inspiration Company then gave way to another, backed by W. B. Thompson, which found 40 million tons of ore. Control then passed to Anaconda and Dr. Louis Ricketts took charge as consulting engineer. He abandoned the mill which had been partially built (to the horror of the stockholders, according to Ira Joralemon) and spent a year and a million dollars experimenting with flotation. The first large copper flotation plant was then built and recovered 50% more copper than had previous gravity mills. It, of course, was highly successful and became the forerunner of modern flotation plants. Inspiration is distinctive as the first fully integrated copper operation in the United States. Three open pits supply sulfide ore to the concentrator and mixed oxide and sulfide ore to a vat leaching and electrowinning operation with leached ore also being sent to the concentrator. In addition, dump leaching supplies pregnant solution for scrap iron precipitation. Inspiration has recently constructed an electric furnace smelter and also operates a continuous casting and rod plant. The new primary 54 in. by 74 in. crusher was completed in May of 1972 and replaced an older unit which was in the way of the open pit development. It is of an unusual circular silo design, which permits dumping 0 from two positions at 90 from each other. One dumping position is in line with the spider, while the other one is at right angles to it. A box girder splitter bar hung from the dump pocket slopes downward from the second dump point, across the spider cap, and rests on the pocket bottom. This splitter was not installed to protect the spider but was to aid in distributing wet ore being dumped from that position to both sides of the spider. Any large amount of wet ore delivered to one side of the spider would pack in the crusher cavity. The round front wall of the 18 ft (5.5 m) deep pocket is unlined except for light steel protection at the top, while the straight back wall is lined with vertically positioned railroad rails. Water for dust suppression is sprayed into the pocket through a cluster of 3/8 in. (9.5 mm) nozzles at the back of the pocket. About 5 gpm (19 lpm) of water are mixed with 90 psi (620 kPa) air upstream of the nozzles to produce a fog which is effective in dust control. The 54 in. Allis -Chalmers gyratory is placed mostly within one quadrant of the circular enclosure to permit placement of the apron feeder on the lowest level in the proper position to transfer crushed ore to the

Jan 1, 1978

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.' I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker's hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By D. M. Clippinger, J. J. Eidel, J. E. Frost

At Ithaca Peak, one of three peaks situated on Duval Corporation's Mineral Park property, a 'Single pulse of quartz monzonite magma intruded the isoclinally folded Precambrian Cerbat complex consisting of schist, quartzfeldspar gneiss, and amphibolite. The magma reacted with the Precambrian rocks, yielding a quartz-diorite rim. As the magma crystallized within the rim, it produced, progressing in'ward, annular bodies of quartz monzonite porphyry, quartz porphyry, and a distinctive quartz porphyry containing abundant podiform, tabular, and irregular quartz masses. These quartz masses are spatially associated with discontinuous crenulate and tabular quartz veinlets. Following crystallization, the Ithaca Peak stock and part of the surrounding Cerbat complex were fractured, producing a stockwork of predominantly northwest and northeast-trending fractures. The stockwork was then mineralized during a period of decreasing temperature by: ( 1) quartz-pyritechalcopyrite veinlets without distinct selvages and with distinct alteration envelopes in which orthoclase was altered to quartz and sericite; (2) quartz-pyrite-chalcopyrite veins and veinlets with distinct selvages and without distinct alteration envelopes; and (3) pyrite-chalcopyrite- galena-sphalerite veins. The Ithaca Peak stock was pervasively sericitized or argillized. The Mineral Park property is surrounded by a zone of propylitization Alteration and mineralization are coextensive in space and were, at least in part, coincident in time. The Mineral Park property possibly was elevated and exposed twice prior to its present exposure. The protore has been enriched by a factor of three. The Ithaca Peak supergene ore body is conformable with present topography and lies above the present water table. The shape of the ore body was controlled by erosion and oxidation of the previously enriched mineralization. Hematite, goethite, and jarosite present at the surface indicate a high primary pyrite environment, but it is possible to recognize that a small proportion of veins and veinlets contained greater amounts of chalcocite and chalcopyrite than pyrite. The igneous facies on Ithaca Peak are the products of differentiation within a solidifying rim according to Bowen's Reaction series. The innermost facies contain more quartz and orthoclase than the outer facies. Late magmatic quartz in the case of Ithaca Peak contains small amounts of pyrite and molybdenite. It is suggested that this quartz-sulfide mineralization, may also have been the product of differentiation the product of differentiation, may indicate that the later hydrothermal mineralization may also have been the product of differentiation.

Jan 1, 1968

By Thomas J. Menner

Jan 1, 1983

By Walter Weeks

THERE is very little useful material in the litera-ture on the construction of manometers, so each experimenter must devise his own instrument. I have experimented for a number of years and have finally built one that is satisfactory. If we are to obtain accurate friction factors in mine-ventilation problems we must use accurate instruments. The most simple and convenient instrument for the mea-surement of small pressures is the inclined manometer or U-tube. By changing the angle at which the tube is set, any desired magnification of the pressure reading may be obtained. The first question in regard to the manometer is: What liquid shall be used? Alcohol, in my opinion, is the best. It does not cling to the glass and it does not attack the rubber tubes. The next problem is the setting of the instrument at the proper angle. One method is illustrated in Fig. 1. The base plate AC is made horizontal by a level bubble. The plate AB, which carries the U-tube, is hinged at A. The angle z which AB makes with the horizontal may be made any value by pinning the end B at the calculated position on the arm CD. Such an instrument may be designed to read directly in inches of water if a liquid of constant specific gravity is used. If the specific gravity varies, a calculation is necessary to convert the reading into inches of water.

Jan 1, 1923

By Bernard E. Fernow

About eight years ago a comprehensive study of American timbers was begun in the U. S. Division of Forestry with a twofold object. On the one hand, it was desired to deternliiie the working-qualities of our numerous economically important timbers, and to furnish reliable standards of strength. 011 the other hand, it was intended to get a clearer insight into the properties and behavior of wood in general, with a view of establishing more rational methods in its use, and to furnish data for physical inspectioil which would permit an intelligent application of the standards of strength, and place upon a rational foundation the so-called " factor of safety," which is at present a mere baseless guess. The first object, namely, the establishment of standards for any given species, requires a very large series of tests, since Wood is an exceedingly variable substance, so much so that in the same tree a variation of 50 per cent. in strength may be found; hence the greater need of rational data of inspection. So far, the insufficient appropriations and facilities at our disposal have permitted us to establish really reliable standards for five species of southern conifers only. These have been deduced from nearly 20,000 tests. Besides these, 10,000 other tests have furnished indicatious regarding some two dozen other species. This work is now entirely abandoned, waiting for more prosperous times. The study of wood in general, however, can be carried on with smaller means, and has this year yielded not only very interesting, but highly important results, which will soon be published in detail. It is the purpose of this paper to make to the Institute the

Jan 1, 1899

By ROBERT R. ABUOTT

(Cleveland Meeting, October, 1912.) THE practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past, 10 years. Formerly, case-hardened steel was held in more or less contempt, since it. was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of cc case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat., or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but. increases rapidly with increasing temperature. Below * Metallurgical Engineer, The Peerless Motor Car Co.

Dec 1, 1912

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

"WELFARE…Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state.In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is pre¬sented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.Even in such camps, however, as illustrated in Bingham, the companies can do much to better welfare conditions. In this camp the Utah Copper Company has spent $800,000 since 1 920 in the erection of modern brick cottages, apartment houses and the Gemmell Memorial Club. The cottages and apartments have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club, erected and equipped at a cost of $1 75,000, was provided by the company for the benefit of the Utah Copper Company employees living in the canyon and has been made the recreational center for the camp."

Jan 1, 1925

By A. V. UDELL

OF all the metals that have from time to time been called the "Wonder Metal," mercury, often called quicksilver, is probably the most deserving of this designation. A wonder metal it must have been to those workers of an earlier day who named it after that Latin god of commerce and gain, characterized as the fleet messenger of the gods and the conductor of souls to the lower world. The word mercury has been used to indicate a carrier of tidings, a bearer of news, a nimble or clever person, a hawker, and a skillful thief. All of these attributes, and more, are recognizable in this metal, the technical terminology of which is "Hydragyrum," meaning water-silver, and from which the chemical symbol "Hg" is derived. Fickle in its occurrence in nature, simple in its metallurgy, illusive in captivity, it serves man in life or death, in war or peace, in commerce, science and arts, in mining, agriculture, and forestry with a versatility found in no other element.

Jan 1, 1929

By Forrest K. Pence

BENTONITE deposits are known to occur in Texas within the Jackson group of formations. This group represents the uppermost Eocene age sediments found in the coastal plain area of Texas. It outcrops across this area of the state in a narrow band of some 4 to 20 miles width. The outcrop pattern roughly parallels the present Gulf of Mexico shore line and is some 100 miles inland from the Texas shore, Fig 1. The principal bentonite deposits are found in the areas where this outcrop pattern cuts across the south-central Texas counties of Karnes, Gonzales, and Fayette. In these deposits, the better quality bentonite is found in the lower or bottom layers of the volcanic ash deposits in which they occur. Some of these better quality bentonites develop very light colors upon firing and therefore justify their being classified as "white firing." The deposits in Karnes and Gonzales Counties apparently occur in commercial quantity, whereas the white firing strata so far uncovered in Fayette County have been too thin to be classified as yet as "commercial." A study of the ceramic properties of the weathered ash in Gonzales and Karnes Counties was reported in 1941.1

Jan 1, 1949

By Captain Lyle

I was very much interested in Mr. Macdonald's paper, and I can say that there is nothing in it to which I cannot heartily subscribe. In speaking of the want of knowledge that has existed, and still exists, among engineers in regard to structural materials, their strength, etc., my own experience has taught me to doubt the reliability of the ordinary testing machines.

Jan 1, 1882

In the January Bulletin a list was published of Societies' publications, magazines, etc., which were duplicates and were discarded at the time of-the consolidation of the libraries of the three Founder Societies. A second list published herewith includes text books which are duplicates and which will be disposed of about April 1, 1916, by the Board of Directors of the Institute through the, Library Committee.. If, meanwhile, members desire to secure some of these books, they are asked to communicate at once with the Secretary as. this is an unusual opportunity to secure books at an extremely low price. Airy, George Biddell.-Magnetism, London, 1870, Bd. Alberti, Friedrich von.-Halurgische geologic. Erster Band. Zweiter Band. Stuttgart, 1852, Bd. American Iron and Steel Association.-Ann. Rep. of the Sec'y. Statistics of American and, Foreign Iron Trades, 1877. Phila., 1877, Bd. Same, for year 1878. Phila., 1879, Bd. American. Telephone and Telegraph Co.-Ann. Rep. of Directors to Stockholders, 1911. N. Y., 1912, paper. Armagnat, H.-Induction Coils. Trans. by Otis Allen Kenyon, N. Y., 1908, Bd. Armstrong Cork Co. Insulation Dept. Nonpareil Corkboard Insulation. Pittsburgh, 1909, Bd. Associazione fra gli Industriali Metallurgici Italian.-The Metallurgic industry of Italy. Description of some of the principal works. Milan, 1911, Bd.

Jan 2, 1916

By Joseph E. Pogue

NEW economic forces are at work in the petroleum industry.. In order to visualize these forces and clearly see their bearing on the producer, refiner and marketer, it is necessary to see in perspective the economic evolution of the business. For several decades prior to 1913 the outstanding feature of the petroleum industry was a trend toward integration, culminating in a huge combine, the Standard Oil Co. An important aspect of this integrative trend, however, was its concentration on the combination aid control of refining and marketing, leaving crude oil production, for the most part, to the exigencies. of small-unit competition. It is a noteworthy coincidence that during this era the law of oil and gas was formulated and applied, whereby these substances had to be reduced to possession to establish ownership; and the forces of competition in crude oil production were thereby intensified. It was to the interest of an industry, safeguarded in its control of manufacturing and markets, to have supply stimulated by legal convention as well as by individual initiative in order that the growing demand could be met without interruption. And so over-production of crude oil during this era was no handicap, but rather an aid, to the progress of the industry.

Jan 1, 1929

By Edward H. Robie

OF the current Adirondack iron mine development, the Benson Mines operation of the Tones and Laughlin Ore Co. (Jones & Laughlin Steel Corp. wholly owned subsidiary) is the last to go into operation. Following an active construction program in 1943, the mine. concentrator and sintering plant were scheduled to enter production in the fall. This description therefore cannot include any operating data, and details of equipment and flowsheet have not as yet been released.

Jan 1, 1943

By J. T. Berling, J. B. Conway

MANY studies have been devoted to the correlation of low-cycle fatigue behavior. Several of these have also been concerned with the identification of an effective approach to the prediction of low-cycle fatigue behavior from short-term tensile data. Perhaps the first such approach was that reported by coffin1 in the form: where is the plastic strain range, Nf is the number of cycles to failure, and c is a constant characteristic of a material. In this analysis by Coffin it was reasoned that in a short-term tensile test the value of Nf could be considered as equal to a , in which case the value of c is interpreted as the tensile ductility, f, measured in such a test. If, therefore, the Coffin equation is assumed to be applicable to a given material, it is a simple matter to predict the low-cycle fatigue behavior. Once the tensile ductility is known, this point is located at Nf = 1/4 on a log-log plot of vs Nf and a line is drawn through this point with a slope of to yield a prediction for the fatigue life. Actually, while this equation is quite useful it is not generally applicable, for experiment has shown that the value of —$ does not reflect the relationship between and Nf for all materials or even for a given material over all temperature ranges. An equation similar to the Coffin equation was prepared almost simultaneously by Manson.2 This expression had the form: In this case the exponent on Nf was not assigned any particular numerical value in accord with the various values of this exponent which had been observed for different materials and at different test conditions. Because of this characteristic it will be recognized that little use can be made of this expression in predicting low-cycle fatigue results. A fairly effective expression for use in predicting fatigue behavior was proposed by Manson3 based on a study of numerous sets of experimental results. This relation (Method of Universal Slopes) makes use of modulus of elasticity, ultimate strength, and tensile ductility, and assumes an exponent on Nf equal to 0.6 in representing the plastic strain range contribution to total strain range. While this equation of Man-Son does not yield completely accurate results it must be recognized as being the best means available at

Jan 1, 1970

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941