Search Documents

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.' Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.' Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo'sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. 'S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. 'A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. 'Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. 'J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; 'L. V. Al'tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By S. Forgeron, W. Shaw, E. L. Zodrow

Trend-surface equations are proposed for volumetric coal estimation in collieries of Sydney Coalfield, Nova Scotia. The statistical technique was first tried on Harbour coal in #20 Colliery investigating resulting residuals for abnormalities. The trend model is accepted as probably being correct as a result of that investigation. Indeed, higher degree polynomial trend- surfaces account for over 80% of the total map variability; these are encouraging statistical results, backed-up by geological knowledge about the coal seam, suggesting that the trend model has economic significance for an off-shore colliery developed to exploit the Harbour coal several kilometers east of #20 Colliery. Specifically, the need for additional offshore drill holes for the new colliery (excepting quality assessment holes) should be considered in light of a developed estimating model for the new colliery. The trend model also finds application in coalfields structurally more complex than Sydney Coalfield.

Jan 1, 1983

By Paul Beck

IT is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation, the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and' consume' the deformed hard material. The extent of stability attainable through recovery is limited, espe-cially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or poly-crystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "straight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals-a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By Paul A. Beck

It is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation. the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and " consume " the deformed hard material. The extent of stability attainable through recovery is limited, especially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or polycrystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "istraight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals—a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By J. E. Lawver, J. D. Raulerson, Charles C. Cook

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent, or at least delay, mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the form of calcined bones at least 2000 years ago (Anon., 1964), and man has used phosphate minerals as a source of fertilization in one form or another for at least 100 years. During 1977 the world produced about 116 Mt of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows: marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits requiring apatite carbonate mineral separation. [ ] Guano, mostly from Chile and Peru, accounts for 0.1% of the total world production, and the calcium phosphates from Ocean, Nauru, and Christmas Islands and the aluminum and iron phosphates from Brazil and Aruba account for less than 4% of the world production and are thus not considered in this classification (Lawver, et al.). At present, marine phosphorite deposits account for about 75% of the world's production; the igneous deposits account for 20%. The igneous deposits low in carbonate minerals are easily concentrated by crushing, grinding, and apatite flotation. The most important igneous deposits are those of the Kola Peninsula, USSR (Woodrooffe, 1972). The igneous deposits high in carbonate materials are of corn appreciably more difficult to beneficiate, but they have been concentrated by froth flotation for a number of years. An interesting but rather complicated flowsheet of this type is at Phalabonva, in the Republic of South Africa (Lovell, 1976). The Phalaborwa deposit is an igneous complex of pyroxenite with a central core of carbonatite surrounded by a serpentine- magnetite-apatite rock called phoscorite. The phoscorite containing about 10% P2O5, 35% magnetite, and 35% calcium magnesium carbonate is currently being processed. The process involves comminuting the material for fiberation and subjecting it to a copper float using a potassium amyl xanthate as collector and triethoxybutane as a frother followed by a magnetic separation of the tailings to produce a feed for phosphate flotation. This process produces a phosphate concentrate containing greater than 36% P2O5 at a P2O5 recovery ranging from 75 to 80%. Considerable success has been claimed for recovering apatite from carbonate-bearing ores at the Jacupiranga Mine of Serrana S/A (Silva and Andery, 1972). The carbonatite currently being mined contains an average of only 5% P205 and is concentrated using a unique flotation process (Andery, 1968) to yield 96% P205 concentrates. The ore contains about 12% apatite, 5% magnetite, 80% calcite plus dolomite, and minor amounts of phlogopite, olivine, zircon, ilmenite, and pyrochlore. Feed preparation consists of crushing to -31.75 mm (-1 M in.), rod milling in closed circuit with hydrocyclones to about 92% (-50 mesh), and two-stage cyclone desliming of the -50 mesh sands at 20 m. Weight recovery in the deslimed feed is normally 85 to 88% and the corresponding P2O5 recovery is usually about 90%. The deslimed feed is conditioned at 60 to 70% solids for 15 min at pH = 8-10 with 0.6 kg/t of causticized starch for iron oxide and calcite-dolomite depression. The conditioned slurry is diluted to 20 to 30% solids, about 0.2 kg/t of fatty acid or soap collector is added to the conditioner discharge, and the reagentized ore is subjected to rougher-scavenger flotation with additional fatty acid added to the scavenger float. The scavenger concentrate is returned to rougher circuit distributor, and the rougher concentrate froth is subjected to two stages of cleaner flotation to yield a final apatite concentrate analyzing 36 to 38% P205. Flotation recovery of P205 is, in general, above 90% when treating fresh carbonatite. The high-carbonate flotation tails normally analyze 1 % P2O5 or less and are suitable for portland cement production. The marine deposits. Types 1 and 2 of central Florida are representative of enormous reserves of phosphate rock that will undoubtedly account for much of the world's production in the near future. Until very recently the sedimentary deposits high in carbonate minerals (Type 2) have not been considered reserves due to the difficulty in making a francolite-carbonate separation. Although no commercial plant has yet been built to beneficiate Type 2 ore, laboratory and pilot plant data indicate the process is viable. If so, the reserves of Florida and similar deposits throughout the world will be substantially increased. A discussion of the beneficiation of these two types of sedimentary deposits and the relation of the resulting concentrates to the fertilizer industry of the United States is the subject of this paper.

Jan 1, 1981

By Waldemar Lindgren

Jan 1, 1905

By Walter Hull Aldridge

Much has been said about the foreseeable exhaustion of known mineral reserves-particularly in the United States. It is claimed that we are about to become a have-not nation insofar as certain essential minerals are concerned; and in this respect our position is often contrasted with that of the world as a whole, largely because we have drawn so heavily on our domestic resources during the last fifty years. As a matter of fact, the difference is not great if one takes a reasonably long-term view of the situation. No one denies that nature endowed the United States richer in mineral resources than any other equal area. It is granted that we have skimmed the cream of many kinds of minerals; but in a free international trade in minerals it would not be many decades before the richer deposits-at least the deposits easy of discovery throughout the world would be depleted to much the same degree as those in the United States today. For it is a fact that the problem of satisfying the needs of our industrial society for minerals is fundamentally worldwide in scope. The singular and significant attribute to all minerals is that there is but a single crop. Forests can be grown, but mineral deposits can be replaced only by finding new ones. Thus, one of the vital tasks of the mining engineer, the petroleum engineer, and the geologist is to find these new mineral resources. Another task is to devise means and methods for the exploitation of, at costs that are economic, low-grade deposits and those deeply buried in the crust of the earth. The first need, however, is to find the deposits in the ground. If the assumptions of those who today fear an early exhaustion of all deposits are valid, the outlook for continued material and social progress is gloomy indeed. I take a more optimistic view, for it is my belief that vast new sources of needed minerals will have come to light before our known resources are gone. The real question is whether the outside layer of the crust of the earth that is accessible to engineers contains adequate mineral deposits; and whether engineers can find those deposits. The answer must be based on geologic science, geologic fact, and mining history. Every continent, and almost every country, has yielded minerals of industrial utility in substantial quantity. Mineral deposits are widespread. Geologists know the conditions that were favorable to the occurrence of ores and the types of rocks in which various kinds of ores may ordinarily be found. They know that such rocks occur over broad regions of the earth's surface. They also know that in large areas rocks that are potential carriers of ores are covered and concealed by material of entirely different character. Such cover may consist of lava flows, layers of volcanic ash, or beds of material washed down from the surrounding mountains. Sometimes those covers are thick, sometimes relatively thin. But men well-qualified to pass judgment are sure that concealed deposits, large in number and in size, exist close enough to the surface to make exploitation practical. Only by actual penetration of the surface can this contention be proved, but to conclude otherwise would be to ignore the laws of probability and to deny the over-all consistency of nature. The task of probing the crust of the earth to determine the location of these deposits, and to obtain some notion of their size and quality, poses serious problems. However, they should not be beyond human solution. Much more research must be done in analyzing and explaining the laws of ore deposition. New tools, in the shape of techniques and methods and of mechanical and electrical devices and instruments, must be developed. But no reasonable person can doubt that these objectives will be achieved. As the need becomes increasingly pressing, scientists and engineers will supply the imagination and the ingenuity that will provide the solution. The time and effort thus far devoted to the development of methods for locating hidden ore bodies have been pitifully meager. Energetic investigation of the subject of applied geophysics is essential to the success of the mineral industry, and I have no hesitation in predicting that effective techniques will be found and successfully applied. Twenty-five years ago the petroleum industry

Jan 3, 1950

By James S. Browning

For the past several years, USBM has conducted laboratory and continuous process development work on the weathered mica pegmatites ores of Alabama, Georgia, and North Carolina to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotation of mica: 1) an acid-cationic method for recovery of coarse mica and 2) an alkaline-anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatite ores. This report summarizes the process development work, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained mica. Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama.'" Whereas in western North Carolina, these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites4 To a lesser extent, mica is produced as a byproduct of feldspar" and spodumene. Past research by U.S. Bureau of Mines (USBM) has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica.' This method requires thorough desliming of the ore with consequent fine mica losses. The other utilizes an alkaline-anionic-cationic process for recovering fine-size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica.8-18 The latter process has also been successfully applied to a micaceous schist ore from California.' This report summarizes the results of these research studies. Both of the flotation processes developed by USBM have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores. Description of Ores The weathered mica pegmatite ores used in the investigations were obtained from commercial mica operations in Alabama, Georgia, and North Carolina. The

Jan 1, 1971

By Herman Dykstra, Irving Fatt

Relative wetting phase permeabilities calculated from capillary pressure-saturation data are compared with measured relative permeability data. The equation relating relative permeability to capillary pressure-saturation data is derived by assuming that a porous medium is analogous to a bundle of capillary tubes. The equation includes a term to correct for the difference between fluid path length and length of core. Relative oil permeability data in the water-oil-gas system are presented, and it is shown that if the water is considered part of he rock matrix, the relative oil permeability curve is typical of a wetting phase relative permeability curve. Apparatus for measuring two and three-phase relative permeabilities are described. INTRODUCTION The difficulty in measuring relative permeability of cores has made it desirable to have a correlation between relative permeability and some more easily measured property of porous media. Such an easily measured property is the capillary preisure-saturation relation. In the past there has been a tendency to separate the capillary pressure concept from the very complex pore geometry and to consider that the capillary pressure-saturation curve give? only some characteristic distribution of interfacial curvature between two fluids.' Recently, however, it has been realized that if capillary pressure data are to yield information concerning pore size distribution2 and fluid flow in porous media. the pore must be assumed to have a simple shape such as a cylinder or a sphere. Childs and George' showed that relative water permeability could be calculated from the capillary pressure-water saturation curve by assuming that the pores are cylinders in which the fluid flowing obeys Poiseuille's Law, and that the capillary preisure curve indicated the size and number of pores. Purcell5 derived an equation relating the permeability of a porous medium to the capillary pressure curve by assuming the porous medium to he analogous to a bundle of capillary tubes. Gates and Lietz6 calculated relative permeability by an equa-tion derived from Purcell's equation. In this paper an equation is derived giving the relative water permeability as a function of water saturation by as-sulning that the core sample can be represented by a bundle of capillary tubes in which the fluid path length is not the same as the bulk length, and in which the fluid path length varies with saturation. THEORY For a bundle of N capillary tubes the flow through dN tubes will be dQ = qav dN ..........(1) where Q is the total flow rate through all the tubes and q., is the aberage flow rate through the tubes in the interval dN. If the interval dN is made small the average flow rate through a tube in the interval dN is given by Poiseuille's Law, 8 nl where ?P is the pressure drop across the tube of length 1 and radius r, and µ is the viscosity of the fluid. Substituting for qav in Equation (1), dQ =pr4 ? P/8µl dN.........(3) Darcy's Law for linear flow of an incompressible fluid in a porous medium is Q = KA?P/µL...........(4) where K is the permeability and ?P is the pressure drop across a bundle of tubes which has replaced the porous medium of length L and cross-sectional area A. Differentiating Darcy's Law with A, ?P, µ, and L constant, dQ = A?P/µL dK.........(5) Equating (3) and (5) gives dK------------dN.........(6) 8Al If the pores are assumed to be cylinders dV =pr2ldN..........(7) where V is the volume of flowing fluid in the pores. Substituting for dN in Equation (6) gives dK = —dV..........(8) 8AI' By definition the saturation, S, of the core is v v S =V/Vp..........(9) Vv -PAL

Jan 1, 1951

By Irving Fatt, Herman Dykstra

Relative wetting phase permeabilities calculated from capillary pressure-saturation data are compared with measured relative permeability data. The equation relating relative permeability to capillary pressure-saturation data is derived by assuming that a porous medium is analogous to a bundle of capillary tubes. The equation includes a term to correct for the difference between fluid path length and length of core. Relative oil permeability data in the water-oil-gas system are presented, and it is shown that if the water is considered part of he rock matrix, the relative oil permeability curve is typical of a wetting phase relative permeability curve. Apparatus for measuring two and three-phase relative permeabilities are described. INTRODUCTION The difficulty in measuring relative permeability of cores has made it desirable to have a correlation between relative permeability and some more easily measured property of porous media. Such an easily measured property is the capillary preisure-saturation relation. In the past there has been a tendency to separate the capillary pressure concept from the very complex pore geometry and to consider that the capillary pressure-saturation curve give? only some characteristic distribution of interfacial curvature between two fluids.' Recently, however, it has been realized that if capillary pressure data are to yield information concerning pore size distribution2 and fluid flow in porous media. the pore must be assumed to have a simple shape such as a cylinder or a sphere. Childs and George' showed that relative water permeability could be calculated from the capillary pressure-water saturation curve by assuming that the pores are cylinders in which the fluid flowing obeys Poiseuille's Law, and that the capillary preisure curve indicated the size and number of pores. Purcell5 derived an equation relating the permeability of a porous medium to the capillary pressure curve by assuming the porous medium to he analogous to a bundle of capillary tubes. Gates and Lietz6 calculated relative permeability by an equa-tion derived from Purcell's equation. In this paper an equation is derived giving the relative water permeability as a function of water saturation by as-sulning that the core sample can be represented by a bundle of capillary tubes in which the fluid path length is not the same as the bulk length, and in which the fluid path length varies with saturation. THEORY For a bundle of N capillary tubes the flow through dN tubes will be dQ = qav dN ..........(1) where Q is the total flow rate through all the tubes and q., is the aberage flow rate through the tubes in the interval dN. If the interval dN is made small the average flow rate through a tube in the interval dN is given by Poiseuille's Law, 8 nl where ?P is the pressure drop across the tube of length 1 and radius r, and µ is the viscosity of the fluid. Substituting for qav in Equation (1), dQ =pr4 ? P/8µl dN.........(3) Darcy's Law for linear flow of an incompressible fluid in a porous medium is Q = KA?P/µL...........(4) where K is the permeability and ?P is the pressure drop across a bundle of tubes which has replaced the porous medium of length L and cross-sectional area A. Differentiating Darcy's Law with A, ?P, µ, and L constant, dQ = A?P/µL dK.........(5) Equating (3) and (5) gives dK------------dN.........(6) 8Al If the pores are assumed to be cylinders dV =pr2ldN..........(7) where V is the volume of flowing fluid in the pores. Substituting for dN in Equation (6) gives dK = —dV..........(8) 8AI' By definition the saturation, S, of the core is v v S =V/Vp..........(9) Vv -PAL

Jan 1, 1951

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By Shosei Serata

Stress control methods of mining have been developed separately in at least four different parts of the world in entirely different types of mining -- coal, trona, salt and potash -- during the decade of the 1960s. They all utilized yield pillars as tools for ground control. Today, yield pillars are becoming widely used in under- ground mines in a variety of geological conditions. Stress control methods are effective in stabilizing openings in weak, complex grounds, especially at greater depths. Their advantage is that they utilize existing ground media to stabilize mine openings by altering the stress distribution patterns around the openings, by controlling design parameters such as room width, pillar geometry, and excavation sequence, rather than by using a conventional means of artificial ground support such as roof bolts, cribbing, or arches. Stress control methods, therefore, are suitable for both advance and retreat mining, including total extraction mining. Adaptation of these methods results in substantially greater safety, productivity, and ecnomy over conventional methods. These methods are based on scrutiny of the actual stress conditions in the ground, by both in-situ measurement and computer simulation. This paper provides a summary of stress control methods as developed over the last ten years. The field examples are limited largely to salt and potash mining applications, although the method has been used successfully in other mining applications. The examples illustrate that stress control methods actually address general ground weakness problems -- separation at discontinuity planes, swelling by shale expansion, deterioration by brittle fracture, and interference by ground water. That is, although the principle is developed mainly with reference to salt and potash applications, it is generally applicable to weak ground.

Jan 1, 1983

By William Waters Van Ness

The Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively reccnt date, were carried out in the neighborhood of the village of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E—W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposcd to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Jan 1, 1909

By E. P. Abrahamson II

The effect of transition element binary solid-solution additions upon the recrystallization temperature of vanadium has been investigated. Cr, Fe, Co, Ni, Mo, Ru, Rh, Os, and IY lower the recrystallization temperature, while Ti, Mn, Zr, Cb, Pd, Hf, Ta, W, Re, and Pt raise it. The majority of elements have their greatest effect in less than 0.15 at. pet. Both the rate of change of recrystallization temperature with atomic percent solute and the limit of initial linearity are found to Correlate with the free atom grozdnd state outer electron configuration of the sollte element. THE work of Abrahamson and Grant1 and Abraham-son and Blakeney2 has shown that the solute&apos;s elec- tron configuration appears to be a prime determinant of both brittle-to-ductile transition and recrystallization temperature in dilute binary alloys. It has also been shown by Abrahamson3 that the limit of linearity, i.e., the limit of initial linear change of recrystallization temperature with atomic percent solute, is also a function of the electron configuration of the solute in iron base alloys. Because of the systematic nature of the solute electron configuration correlation, it is to be expected that some systematic variation might be observed upon changing the solvent. Thus, this study of recrystallization in vanadium base alloys is the first of a series aimed at defining the role played by the electron configuration of solute in determining the recrystallization characteristics of dilute transitional alloys. PROCEDURE All alloys were made using 99.8 pct V containing 0.011 C, 0.024 N, 0.08 0, 0.006 H, 0.035 Ta, and

Jan 1, 1962

By Howbert Van Dyne

THE Presidio mine of The American Metal Co. is situated in the "Big Bend" region, some 45 miles over state highway south of Marfa, a station on the Southern Pacific R.R. It lies 20 miles by road north of the Mexican border, in semidesert surroundings typical of this general section of the United States and the adjoining part of Mexico. All supplies are hauled in by truck from Marfa under contract. The concentrates and precipitates produced by the mill are carried by the same trucks to Marfa, from whence they are shipped, respectively, to the El Paso and Selby plants.

Jan 1, 1930

By John C. Draper

The principal object of an underground coal mine transportation sys tem is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine ; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served: 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1973

LATEST estimates of Russian steel production for 1951 give rise to the belief that on at least one vital front, the Western bloc of nations has maintained a definite advantage. On the surface, we are outproducing the Eastern bloc by more than twice. The United Nations Economic Commission for Europe estimates Russian output at 31.30 million tons, a 15 pct increase over the previous year. Production for the entire Iron Curtain is figured at 40.93 million tons. Western Europe alone produced 17 pct. more steel during the same period. The figures are misleading in one sense. We have no precise idea of how much steel is being used for arms. The Western nations are still expending much of their production for consumer goods, and you cant throw washing machines in a shooting war. It is significant to note that Russian production is well, beyond estimates made by world authorities prior to the current international situation. INTERIOR Secretary Oscar L. Chapman warns that the United States must make use of the resources of other nations or face mineral impoverishment once the time of struggle is over. He pointed out that the present struggle between two ideologies can leave the United States in such a state as to preclude anything but political&apos; victory-with an accomp anying economic loss that will be irreparable. Chapman scored the attitude whereby conservation programs are looked upon as a luxury, pointing out that the nation faces an ever increasing need for action on that front. He also announced that the Bureau of Mines doubled its facilities for producing pure zirconium during 1950-51 at the request of the Atomic Energy Commission. Zirconium may be an important structural metal for atomic power devices. The Interior Secretary also said that the AEC has provided the Bureau with funds for the study of radioactive minerals and to help test and evaluate about 9000 ore samples believed to contain uranium.

Jan 1, 1952

By Milton E. Wadsworth, Edward M. Eyring

BETTER understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique1,2 employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra. In applying the pellet technique to solids of large surface area, French and his coworkers3 have surveyed the adsorption of organic flocculants on clay minerals, oleic acid on fluorite, and ammonia on cracking catalysts. Recent work on application of differential infrared spectroscopy to the study of solid surfaces&apos; has demonstrated that the difference between a sample and a reference can be obtained with double-beam instrumentation. In this way displacement of surface products, adsorption of new products, and differences in the substrate, if any, may be detected. Experimental Procedure: Potassium iodide pellets were used in this study, prepared from recrystallized analytical reagent grade KI. Grinding was carried out in a Fisher mechanical agate mortar. Two-gram plates containing the solid under study were pressed in a special evacuated die constructed in the laboratory at the University of Utah." Concentration depended on the solid in question. Zinc sulfide and willemite are sufficiently transpar- ent in the infrared region for concentrations as high as 20 mg of mineral in 2g of KI to be used. Zinc oxide is even more transparent, permitting concentrations as high as 60 mg in a 2-g plate. For non-differential operation, however, much lower concentrations (2 to 10mg/2g KI) had to be used. Spectra were obtained on a Per kin-Elmer 21 double-beam recording infrared spectrophotometer. A sodium chloride prism was used giving a spectral range of approximately 2 to 15 v wave length. For differential runs a resolution of 1000 was used and the scanning speed was controlled commensurate with instrument response. The response was checked continuously and each spectrum was repeated several times. For nondifferential runs a resolution of 927 was used. Zinc oxide used was analytical grade oxide fume. The zinc sulfide was precipitated from solution with analytical grade zinc sulfate and sodium sulfide. The precipitate was washed and centrifuged several times and dried. Before use the precipitate was washed in dilute HCl and then treated with saturated NH4Cl to remove any bulk oxides and sulfates. X-ray patterns of the precipitate were comparable to that of the natural mineral sphalerite. The precipitate was much more satisfactory than finely ground natural ZnS because of its very large surface

Jan 1, 1957

By Gen-ichi Nakazawa, Masamichi Fujimori, Ichiro Doi

INTRODUCTION The major products of nickel industry in Japan are the electrolytic nickel (E-Ni), the ferro-nickel (Fe-Ni) and the nickel oxide sinter (NOS), totaling in production to 90 - 100 X 103 tons/year in terms of pure nickel content, and sharing approximately 20% for E-Ni, 10% or less for NOS, and the rest for Fe-Ni. The raw materials to be used for these products depend totally upon the imports from abroad; matte, the raw material used in the production of E-Ni, is from Australia and Indonesia; matte for the NOS is from Indonesia and New Caledonia; and garnierite, the raw material for Fe-Ni, is imported in bulk from New Caledonia, Indonesia and the Philippines. This report describes the acquisition of these raw materials, the production processes, trend of supply-demand, problem areas and the measures taken, and so forth, in connection with the nickel industry in Japan. ELECTROLYTIC NICKEL 1. History The nickel industry in Japan began in 1939 by the Sumitomo Metal Mining Co., Ltd. (SMM) with 150 tons E-Ni/month under the blast furnace smelting and the metal anode electrolysis. This was temporarily suspended after the end of last World War II, but resumed in 1952 with garnierite of New Caledonia as a raw material. Since then, the production capacity has been expanded incidentally to the increase of demand. However, since the smelting of garnierite contained about 2% nickel was very costly, the smelting process had been changed to smelt the briquettes of the mixture of garnierite and nickel sulfide concentrate imported from Canada and Australia. In 1975, this smelter was closed, and SMM&apos;s nickel refinery used matte from Western Mining Corp. (WMC) of Australia as a raw material. The refining process had been the metal anode one. The crude nickel oxide derived from roasting the high grade nickel matte had been melted and reduced with coke in the electric furnace and cast into anode. In 1970, a new refinery was constructed to produce 1,000 tons Ni/month under the matte anode process, and further, in 1976, the old refinery was converted into the matte anode process, thus resulting in the total production capacity of 1,690 tons Ni/ month today under the matte anode process. Shimura Kako Co., Ltd. began in 1951 to produce a little of E-Ni, and in 1955, they constructed a shaft furnace smelter with New Caledonian garnierite as a raw material to begin the E-Ni production under the matte anode process. Its monthly production reached 400 tons in 1957, but it discontinued its smeltering in 1963 to convert to the matte import from S. Le Nickel, WMC and INCO. In 1979, it changed the source of matte supply from the above to Soroako of Indonesia, discontinued the E-Ni production in 1979, and arranged for a total toll contract with Sumitomo. Meanwhile, SMM has developed a very distingished process for nickel-cobalt separation and refining by a solvent extraction method from nickel and cobalt mixed sulfide generated as a by-product in the nickel recovering process from laterite under the Nicaro process. Nippon Mining Co., Ltd. (NMC) also developed its own process. The plants under these processes were constructed in 1975, with the monthly production capacity of 230 tons of nickel and 130 tons of cobalt by SMM, and 300 tons of nickel and 110 tons of cobalt by NMC. SMM imports the raw material from the Marinduque Mining and Industrial Corp. of the Philippines, while NMC from Queensland Nickel Pty. Ltd. of Australia. 2. Production Status 2.1 Producers and materials Today, SMM holds the monthly E-Ni production capacity of 1,920 tons, of which 1,690 tons are from the matte anode process, and the remaining 230 tons are from the mixed sulfide as a raw material. NMC also uses the mixed sulfide as a raw material for a production of 300 tons/month. [ ] Most of SMM&apos;s raw material, nickel matte, is imported from WMC of Australia, partly using the Soroako matte from Indonesia. An example of material analysis is given in Table 1. Matte is a raw material for E-Ni and NOS, and the major sources of matte supply at present are Australian WMC and Indonesian Soroako, occupying ap-

Jan 1, 1982

By P. A. Beck, L. J. Demer

As reported in a previous publication,&apos; isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949