Search Documents

By J. B. Clark, A. S. Yue

PfANN1 has shown that when a cylinder of molten binary alloy freezes directionally, the solute distribution can be described analytically by cg=k(l-g)k-1 [1] in which Cg is the solute concentration in the solid at the point where a fraction g of the original liquid has frozen and Co is the initial solute concentration. The term k is the effective distribution coefficient of the solute and is defined as the ratio Cx/CL where Cl is the solute concentration in the main body of the liquid. Both the slope and the intercept at -log (1 - g) = 0 of a logarithmic plot of Eq. [I.] provide a measure of k. Under conditions of freezing where diffusion in the solid is negligible and the solute concentration in the liquid is uniform, the effective distribution coefficient k, derived as above, is equal to the equilibrium distribution coefficient taken from the phase diagram. However, under ordinary freezing conditions, even though solid-state diffusion is negligible, the solute rejected from the freezing solid does not have sufficient time to diffuse uniformly throughout the main body of the liquid. A concentration gradient is formed in a boundary layer in front of the advancing solid-liquid interface as pointed out by Rutter and Chalmers.' Thus, under these conditions, the concentration of the freezing liquid in the boundary layer is higher than that predicted from the equilibrium phase diagram and consequently the effective distribution coefficient k, obtained from directional freezing experiments, is larger than the equilibrium distribution coefficient. The symbol k will designate the effective distribution coefficient in the discussion which follows. In this paper, the determination of the effective distribution coefficient is demonstrated for several dilute binary alloys and a polynary magnesium alloy. The effect of freezing rate on the value of the derived k is presented in detail. An example for the calculation of the solidus in a dilute binary solution using the experimentally determined effective distribution coefficient is given. MATERIALS STUDIED Binary magnesium alloys of copper, nickel, and zinc containing approximately 0.10 wt pct solute and a polynary alloy containing approximately 0.10 wt pct each of several elements were selected for study. The spectrographic analyses of these alloys are given in Table I. The analyses are believed accurate to within +5 pct of the stated value. EXPERIMENTAL PROCEDURE Extruded rods of the alloys, 3/8 in. in diam and 11 in. long were used for directional freezing studies. The alloy rods were melted horizontally in a high-purity graphite boat by a Nichrome-wound tube furnace which moved parallel to the length of the rod. The boat was supported inside a Vycor tube suitably connected to provide a protective atmosphere of dry SO2. For an experimental run, the following procedure was used. The alloy rod was cleaned in dilute HNO, and dried. The graphite boat containing the alloy rod was placed within the Vycor tube and the tube connected to the gas train' The 'ystem was purged for 20 min with dry argon and then a flow of dried SO, was maintained for the duration of the run. The movable furnace was positioned and either all or a desired portion of the alloy rod was melted. After attainment of steady-state temperature gradients the molten bar was solidified from one end to the other at a controlled rate by pulling the furnace along the length of the bar at the desired speed. At the conclusion of the run, the directionally frozen alloy rod was analyzed spectrographically at 1 1/4-in. intervals.

Jan 1, 1961

By Sukune Takenouchi

Porphyry copper deposits in the southwestern Pacific region differ in some points of geologic features from those of the United States. The deposits distribute along old or active island arcs and are generally younger in age (1-16 m.y. B.P.). In Japan, however, no typical porphyry copper deposits are yet reported, though the geological situation of Japanese islands is similar to that of the southwestern Pacific. Fluid inclusions in some porphyry copper deposits In the southwestern Pacific region and those in igneous rocks genetically related to the ore deposits In Japan have been studied, and the genesis of ore-forming fluids from igneous rocks are discussed. From the results, the possibility of finding porphyry copper-type mineralization in Japan are considered.

Jan 1, 1976

By J. B. Clemmer

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgC03), usually is associated with lime-stone (CaCO3) and dolomite (MgC03 CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amor-phous) forms.2 The more common crystal-line mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories.

Jan 1, 1940

By Robert McClurkin

Over a long period of time considerable attention has been paid to the chemical properties of the materials entering the iron blast-furnace charge. Infinite care has been used in the selection of materials having the correct chemical composition. Little attention has been paid to the physical properties of either the ore, coke or limestone. Until comparatively recent times the coke as produced, as well as the ore, was charged into the furnace without any attempt to maintain uniformity in physical size. Recently some work has been done along the lines of sizing of coke and in some cases the sizing of ore has been applied. In each instance marked results in the efficiency of operation have been attained. The effect of changing the physical size of the materials entering the burden has been reflected directly in the coke consumption. From the experience of operators and the results of numerous investigations which have been conducted on blast-furnace materials, it may be stated definitely that the physical properties of the materials entering the charge have as much bearing on the efficiency of the process as the chemical properties of these materials. Structure of Sinter On the Continent and more recently in this country iron-ore sinter has been introduced in blast-furnace burdens. The effect of the use of sinter has resulted in a material reduction in the coke consumption and an increase in the capacity of the furnace. The effect of the use of sinter is due undoubtedly to its porosity and to its physical size and, incidentally, to the chemical condition of the iron in the sinter and to the absence of combined water. Compared with Mesabi ores, all sinters are generally larger in size than the ore particles, and the structure of the sinter differs considerably from the structure of the ore. In sinter the mass is porous and open and makes available a great deal of surface for gas contact during the process of reduction. Most ores are relatively dense and nonporous and when the particle size is large the time element required for reduction is materially increased. The result of a very thorough investigation on iron-ore sinter by Schwartzll has shown that sinter is completely cellular in structure and

Jan 1, 1932

By George Enos

As the coating formed affects the corrosion rate, duplicate samples of eight non-ferrous alloys were placed in flowing mine water. The alloys tested were as-cast or as-rolled and machined or polished. The paper describes the tests and gives the corrosion losses and the appearance of the samples at the end of the test. AN IMPORTANT factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the, terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2 mm. (equivalent focal length) apochromatic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002-0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002-0.0004 mm. thick. This thickness is equivalent to 200,000-

Jan 7, 1924

By L. A. Adorjan

The tensile strength of agglomerate models due to capillary forces has been determined by computation of the exact surface profiles. Graphs showing tensile strength as a function of moisture content and contact angle me given for spheres in cubic arrangement. Another model of cones attached to cube faces, in cubic packing, provides a better representation of angular particle agglomerates. An algebraic formula approximating tensile strength as dependent on surface tension, particle size, moisture content, contact and cone angles was developed. The phenomenon of "capillary evaporation" due to high negative capillary pressures is explained and its influence on tensile strength of agglomerates is evaluated.

Jan 1, 1977

By John T. Norton, V.G. Mooradian

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By V. G. Mooradian, John T. Norton

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By R. Hogg

INTRODUCTION As mineral particles are made smaller and smaller, it follows that their surfaces assume a greater and greater importance. In the extreme, the colloidal systems are characterized by the complete dominance of surface over bulk properties. Surface characteristics and properties will clearly influence any fine-particle processing operation. Comminution, for example, is a process of creating new surface. Agglomeration, on the other hand, may involve the reduction of surface area and the forces involved are generally surface forces. All mineral separations, solid-solid as well as solid-fluid, involve the treatment of two or more phases (solid plus liquid and/or gas). As the interfacial area increases, so will its effects on processing. Both physical and chemical separations are influenced by interfacial phenomena. Gravity separations are usually performed in a liquid phase and may be affected, for example, by the wetting characteristics of the solids. Flotation processes, of course, are based on the exploitation of differences in surface properties. Hydrometallurgical processing usually involves interfacial chemical reactions, e.g. leaching. The rates of such reactions depend on surface area and may be influenced by electrochemical effects in the electrical double layer at the solid-liquid interface, or by adsorption of reactant and/or product species from solution. In characterizing a mineral surface, it is important to consider first the surface area, since this determines the relative importance of the interfacial effects. The structure and chemical composition of the surface, which may depend on segregation of impurities within the solid and on adsorption from the external environment as well as on the bulk composition of the solid, will generally determine such

Jan 1, 1980

By W. D. Steele, S. D. Brady

THE Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains mineable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon¬galia Co. thence south and southwest across the state to Wayne Co. near Huntington. The Pittsburgh coal is also mineable in the Upper Potomac region but is now practically exhausted there. The total mineable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13% billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio river as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern. West Virginia District comprising Wetzel, Monongalia, Marion, Preston, Harrison, Doddridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 188o (when the Monongahela River Railroad, now B. & O. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgantown and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Monongahela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of mineable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. ECONOMIC IMPORTANCE The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1948

By W. D. Steele, S. D. Brady

The Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains minable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon-galia Co. thence south and southwest across the state to Wayne Co. near Hunt-ington. The Pittsburgh coal is also minable in the Upper Potomac region but is now practically exhausted there. The total minable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13¼ billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio River as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern West Virginia District comprising Wetzel, Mon-ongalia, Marion, Preston, Harrison, Dodd-ridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 1880 (when the Monongahela River Railroad, now B. & 0. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgan-town and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Mononga-hela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of minable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. Economic Importance The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1949

By C. Schlumberger, M. Schlumberger

The object of this paper is to clarify the idea, so important when exploring by potential methods, of the depth of investigation attainable by electrical measurements. After defining, with some precision, .the term "depth of investigation'' in geophysics, the authors show how it is possible to regulate this depth in potential methods and to obtain an 'electrical drilling" from surface observations. They consider also the difficulties encountered in deep measurements and indicate how it is possible to reach greater depths than those having an industrial interest. Depth of Investigation The term, depth of investigation, in its general sense, is easily understood. For instance, a driller who can pull cores from a depth of 2000 m. is capable of working, with accuracy, to that depth. By means of a properly placed drill, he may locate an orebody at a depth of 1999 m., however small this orebody may be. On the contrary, the term as used in geophysics requires precise elaboration. As a matter of fact, no geophysical method, irrespective of the physical property studied (density, magnetic permeability, conductivity), can discover a very small body at a great depth because, in practice, the physical parameter upon which such a geophysical method is based is never regular enough, throughout the ground, to distinguish the feeble anomaly caused by the small, deep-lying body from the numerous anomalies due to irregularities of the encasing terrains. Aside from this question of the ratio between the size of the body being hunted for and its depth of burial, a second factor plays its role in the possible depth of investigation; that is the difference, for the parameter under consideration, between the body and its surrounding material. The greater this difference, and the more homogeneous the encasing terrains, the greater is the possible depth of investigation. This being generally established for all geophysical methods, it is possible to distinguish two main classes of these methods, from this same point of view

Jan 1, 1932

By Kazutami Imai

Effects of heavy metal ions on the growth and the activities of iron and sulfur oxidation of Thiobacillus ferrooxidans were investigated. Mercuric, silver, and stannous ions inhibited both of the growth and the iron- oxidizing enzyme system of the bacterium. On the other hand, uranyl ion inhibited the growth, but it gave almost no effect on the iron-oxidizing enzyme system. The inhibitory effect of uranyl sulfate on the growth of the bacterium is intensified on lowering the cultivating ' temperature from 28 ºC to 7 ºC. In the concentration of 10-3M, cadmium and copper ions inhibited colloidal sulfur-oxidizing activity of the cells 69 and 52 %, respectively, though they did not inhibit the iron-oxidizing activity at all in the concentration. On the contrary, stannous chloride did not givr any effect on the sulfur-oxidizing activity of the cells, though it inhibited the iron-oxidizing activity 55 % in the concentration of 10-3M. Several differences were observed among the cytochrome systems of cell-free extracts of the cells grown on iron and on sulfur.

Jan 1, 1976

By Frank Firmstone

It is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawingboard, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumbbobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

By L. S. Darken, H. A. Wriedt

The equilibria at 1 atm total pressure and 600° to 1300°C (1112° to 2372°F) between gas mixtures with various partial pressures of the reactive constituents (principally sulfur dioxide, carbon dioxide, water vapor, oxygen or carbon monoxide, and hydrogen) and coexisting solid phases (groups variously including calcium oxide, calcium carbonate, calcium sulfide, calcium sulfate, iron, ferrous sulfide, and the iron oxides) are examined. Tables and charts show the combinations of temperature, oxygen activity, and carbon dioxide partial pressure under which the various groups of the solid phases coexist and the corresponding sulfur dioxide pressures. In the presence of calcium sulfide, calcium sulfate, and calcium oxide, the partial pressure of sulfur dioxide has a peak value at each temperature which increases from 101 atm at about 800°C (1472°F) to 1 atm at about 1200°C (2192°F). With water vapor present, hydrogen sulfide may predominate among gaseous sulfur compounds, particularly at low temperatures and oxygen activities; under all other circumstances considered, sulfur dioxide is the dominant gaseous sulfur-bearing species.

Jan 1, 1974

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By Hamilton Wingate

In his paper on the hydraulic mining of a low-grade gravel in California,* Mr. W. H. Radford expresses the hope that other members of the Institute will contribute, for the benefit of all, their experience in similar lines. In these notes 1 shall describe the conditions and results of the operation of the Gold Bug Mining Co., of Cleveland, O., at Georgetown, Eldorado county, Cal.

Jan 1, 1903

By Arthur F. Taggart

In 1900, Elmore found that if an acidulated pulp was stirred up with an oil which was relatively insoluble in and lighter than water, and the mixture was allowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is twofold, first to select the sulfide from the gangue—what today is called collection—and second, to buoy the collected sulfide away from the gangue. The action in collecting is illustrated by Fig. 1: which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids. we consider the oil and water fixed and the solids presented to the surface of contact, the condition will be as shown in Fig. 2; the sulfide tends to be drawn into the interface and the gangue to be excluded. The sulfide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them there. Gas as Buoyant Medium of Flotation In 1906 Sulman. Picard and Ballot discovered a practical and substantially fool-proof method of doing what Everson, in 1886, and Fro-nlcnt. DeBavay Bessel and Elmore had been doing in the intervening years, viz.: using gas in place of oil as the buoyant medium for flotation, but retaining oil as the agent. To all of these inventors "oil," with no qualification as to its kind and no true understanding of its function, was the important thing. Hut they placed on the oil an additional burden viz.: froth-making, and it soon became apparent that not all oils were suitable for the dual purpose. As a matter of fact, it is probable that each of these inventors knew only one suitable oil at the time he wrote his patent, but used the generic term in the patent with the usual idea

Jan 1, 1928

By Arthur F. Taggart

IN 1900, Elmore found that if an acidulated pulp was stirred up. with an oil which was relatively insoluble in and lighter than water, and the mixture was allowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is twofold, first to select the sulfide from-the gangue-what today is called collection-and second, to buoy the collected sulfide away from the gangue.. The action in collecting is illustrated by Fig. 1, which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids, we consider the oil and water fixed and the solids presented, to the surface of contact, the condition will be as shown in Fig. 2; the. sulfide tends to. be drawn into the interface and the gangue to be excluded. The sulfide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them, there. GAS As BUOYANT MEDIUM OF FLOTATION In 1906 Sulman, Picard and Ballot discovered a practical and substantially fool-proof method of doing what Everson, in 1886, and Froment, DeBavay, Bessel and Elmore had been doing in the intervening years, viz.: using gas in place of oil as the buoyant medium for flotation, but retaining oil as the agent. To. all of these inventors "oil," with no qualification as to its kind and no true understanding of its function, was the important thing. But they placed on the oil an additional burden; viz.: froth-making, and it soon became apparent that not. all oils were suitable for the dual purpose. As a matter of fact, it is probable 'that each of these inventors knew only one suitable oil at the time he wrote his patent, but used the generic term in the patent with the usual idea

Jan 1, 1928