Search Documents

By M. S. Abrahams

Germanium has been rolled in the temperature range of 700o to 800°C. The thickness has been decreased by as much as a factor of four, from a thickness of 0.032 in. to a thickness of 0.008 in. For deformations below 60 pet, the true strain per pass is found to be a constant; from the temperature dependence of this slope, an activation energy of about 2.5 ev is obtained. This energy agrees with that for dislocation climb in germanium . For reductions greater than 60 pet, complete rings are seen in the Lave photographs, new grains are observed in the microstructure, considerable softening occurs, and the hole mobility is very low. This evidence indicates that the recrystallization of gertnanium has occurred. GERMANIUM has been deformed in many ways1 including tension, compression, torsion, and bending since Gallagher2 first described its plastic nature at elevated temperatures. All of these studies indicate that the glide plane in germanium is (111) and that the glide direction is (110). Rolled germanium specimens were used by Kolm, Warekois, and Kulin3 in their X-ray study of deformed semiconductors, but no information is given on the rolling itself. The present experiments deal with the rolling of germanium at various temperatures and for different orientations. In all previous deformation studies, the phenomenon of recrystallization (i.e., the transformation of a single crystal into a polycrystal) in germanium has not been observed4 despite relatively large deformations at elevated temperatures. The proposed reason4 for this was that sufficient energy could not be stored in the deformed germanium lattice. In contrast to the earlier studies this work will present evidence indicating that recrystallization occurs in germanium during rolling at an elevated temperature. I) EXPERIMENTAL PROCEDURE A) Test Specimens. The samples used for rolling were in the form of rectangular parallelepipeds measuring 0.3 in. long, 0.06 in. wide, and 0.035 in. high. They were cut from an undoped single-crystal ingot of p-type germanium with a resistivity of 24.4 ohm-cm, a Hall mobility of 2300 sq cm v-' sec-l, and a hole concentration of 1.1 x 1014 cm"3 at room temperature. The surfaces of the specimens were metallographically polished prior to rolling. The initial dislocation density of the samples was about 10' cm-' as determined by etching in CP4. Two different specimen orientations were used. In the first case, the direction of rolling was parallel to (251), the surfaces in contact with the rolls were of the form (1021, and the normal to the third face was parallel to (211). The corresponding di-

Jan 1, 1964

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

NOTHING makes the run-of-the-hall Congressman feel quite so secure as to be on an investigating committee. It's sure fire publicity for one thing and is a convenient excuse for absence from Congressional sessions when controversial issues are being balloted. The minerals procurement program has just had a thorough investigation by Congressmen of the House Interior and Insular Affairs Committee who heard valuable testimony from men like John D. Morgan, director of materials procurement, DPA. He listed over 40 government agencies concerned with mineral affairs. Testimony disclosed the justification for many of the agencies but Congressmen and mine operators have been regarding the defense minerals program in the same light as did the mining student who remarked to the descriptive geometry prof "it's not the intrinsic difficulty of the problem which gives me trouble; it's the multiplicity of detail."

Jan 9, 1951

By Donald L. Katz, Leslie J. Noaker

Experimental data are presented for hydrate formation conditions for mixtures of hydrogen sulfide and methane. Vapor-solid equilibrium constants for hydrogen sulfide are also presented. Equilibrium constants, defined here as the ratio of the mole fraction of hydrogen sulfide in the vapor phase (dry basis) to the mole fraction of hydrogen sulfide in the solid phase (dry basis), were calculated using the vapor-solid equilibrium constants for methane presented in an earlier paper. The conditions at which a natural gas will form gas hydrates with water may be computed from its composition, when hydrogen sulfide is present in addition to carbon dioxide and the paraffin hydrocarbons. INTRODUCTION Many gases are known to form solid hydrates in the presence of liquid water at temperatures above 32°F. This hydrate formation is of importance to the natural gas industry inasmuch as most of the constituents found in natural gases will form hydrates. The attention of the industry was called to hydrates by Hammer-schmidtl0 in 1934. A number of papers have been written giving the temperatures and pressures at which these hydrates will form3,4,5,6,7,8,9,10,13,14,15,18,19 and a bibliography on the subject has been compiled13. Deaton and Frost4,5,6,7,8 report work for various pure gases and for some natural gases. Katz and co-workers3,4,13,14,18,19 have reported data for various gases at high pressure. They developed a method of predicting conditions for hydrate formation from equilibrium constants3,19 and from gab gravity." The effects of anti-freeze agents on the formation of hydrogen sulfide hydrate were reported by Bond and Nelson.' The hydrogen sulfide-water system, including hydrate, has been the subject of recent investigation by Sage and co-workers." Mixtures of hydrates behave as solid solutions and an equilibrium exists between the vapor phase and the solid phase that appears to be comparable to the equilibrium between vapor and liquid phases.3,10 By means of the vapor-solid equilibrium constants which have been published for methane, ethane, propane, iso-butane, and carbon dioxidel6 it is possible to determine the temperature and pressure at which hydrates will form for a specific gas mixture when water is present. Hydrogen sulfide which is frequently found in natural gases has a very strong tendency to form hydrate and must enter the solid solution when present in a natural gas forming a hydrate. To determine the effect of hydrogen sulfide when computing the conditions for gas hydrate formation, it is necessary to have the equilibrium constant giving the ratio of the concentration of hydrogen sulfide in the gas phase to the concentration in the solid phase. This paper presents data on hydrate formation for mixtures of hydrogen sulfide and methane and presents the equilibrium constants which were calculated from these data. EXPERIMENTAL PROCEDURE The apparatus used to determine the conditions of hydrate formation for the methane-hydrogen sulfide system was similar to that employed by previous investigators.3,18,19 A charge gas cylinder was used to supply the hydrogen sulfide-methane mixtures, called the charge gas, and to supply the pressure up to 1.000 psia. This

Jan 1, 1955

By Eckley B. Coxe

IN making surveys in the anthracite coal regions of Pennsylvania, the ordinary engineer's chain (50 or 100 feet long) is generally used, both above and below ground. Sometimes, where it is difficult to chain, as, for instance, across a chasm, a wire is stretched from one station to the other, the distance is marked on the wire and its length is then measured with the ordinary chain. Having had occasion lately to make some surveys where it was necessary to determine with great accuracy the position of the land or property line, not

Jan 1, 1874

By Eckley B. Coxe

In making surveys in the anthracite coal regions of Pennsylvania, the ordinary engineer's chain (50 or 100 feet long) is generally used, both above and below ground. Sometimes, where it is difficult to chain, as, for instance, across a chasm, a wire is stretched from one station to the other, the distance is marked on the wire and its length is then measured with the ordinary chain. Having had occasion lately to make some surveys where it was necessary to determine with great accuracy the position of the land or property line, not

By G. O. Prickett, P. Somasundaran

An experimental progmm based on statistical principles is used for optimizing a flotation operation for the separation of minerals. In this case, flotation of sylvite from sylvinite ore with amine and starch as the flotation reagents was studied to find the optimum reagent levels at various slime levels. The experiments were first done on a two-level three-factor design. Analysis of the results showed that the interactions between various factors were significant. Hence, a first-order linear model of the flotation response would not be accurate. The two-level three-factor design was expanded into a composite design in order to test the fit of a higher-order model. Data were treated to obtain an expression for flotation response as a function of the different variables, to predict the optimum reaaent levels at various slime levels, and also to determine the path of steepest ascent. Tests around the predicted optimum and along the path of the steepest ascent were done until a near-optimum region was obtained. Exploration of the nature of the response surface in that region established the actual location of the maximum response. The optimum amine level was found to be 0.20 lb of amine per ten of ore at all slime levels, while the optimum starch level varied as a function of the slime present. Computer access at the laboratory by means of a teletype terminal on a commercial time-sharing system enabled efficient and accurate treatment of experimental data. The efficiency of experimental investigations can be improved significantly by the use of experimental design and data analysis based on statistical principles. The common approach used in experimental research is to study a property of a system as a function of "one-variable-at-a-time". Several authors'-4 have pointed out the inadequacy and deceptiveness of this method. Results obtained for the effects of a variable on the measured response of the system using

Jan 1, 1970

By H. J. Wasson, E. B. Hopkins

Throughout 1928, production of oil from Venezuela steadily increased, and at the close of the year, the output was at the rate of nearly 400,000 bbl. a day. The total for the year was approximately 106,500,000 bbl., representing an increase of about 66 per cent. over the 63,000,000 bbl. produced in 1927. Venezuela now stands next to the United States as the second largest oil-producing country in the world; and there is abundant evidence to suggest that this relationship will endure for a number of years. Reserves were notably increased in the Lake shore fields, and the potential output of the Maracaibo Basin is much greater than the current production. In spite of this, the percentage of production increase was comparatively moderate, and the rate of this increase continued to fall off slightly, as has been the case for the last three years. This does not suggest that further annual increases in Venezuelan output will not materialize; only that the rate of these increases appears to be on the decline, and that with every succeeding year the future tendency will be in the direction of a stabilized level of output. The following table shows the production trend of the country since 1925: 1925 increase over 1924, 132 per cent. 1926 increase over 1925, 80 per cent. 1927 increase over 1926, 75 per cent. 1928 increase over 1927, 66 per cent. Many factors will work to prevent a reversal of this trend, but the principal ones are strong ownership in large-acreage units, and the probable indisposition of the world market to absorb a more rapidly increasing Venezuelan output at prices profitable to the producers. The distress oil element is not a factor in Venezuela; also, any unforeseen jump, such as results in the United States from the discovery of a Seminole or a deep sand at Long Beach, or Santa Fe Springs, is impossible in Venezuela, on account of lack of means for transporting a sudden surplus of oil, and the slowness with which additional transportation equipment in the form of shallow-draft tankers can be obtained.

Jan 1, 1929

By F. William Bloecher, William B. Plank

CURRENTLY 12,892 students are enrolled in the mineral engineering schools of the United States and Canada, marking an all-time record high for these schools. It shows a remarkably rapid recovery from the effects of World War II. Enrollment in all the other engineering branches has also increased but not so rapidly as in the mineral engineering branch. Almost all the data in this report are from the eighth questionnaire study of the mineral engineering schools made, as formerly, under the auspices of the Mineral Industry Education Division of the AIME. Every school is represented in the data, for which the authors thank the deans and professors who supplied the information. For this reason, the data of all the studies are comparable, an achievement not always possible in endeavors of this kind. For comparison with the general engineering enrollment situation, data are included from the January 1947 issue of the Journal of Engineering Education.

Jan 1, 1947

Dr. Rausch, from your vantage point as educator, engineer, and corporate executive, what would you say is the most fundamental need that must be satisfied for the continuing welfare of our society, our industry and our profession?

Jan 3, 1977

By E. W. Steele

IN THE copper-casting department of a modern electrolytic copper refinery there are two kinds of casting furnaces: the first, or anode furnace for casting crude copper into anodes for electrolysis; the second, or refined-copper furnace for casting the cathodes resulting from electrolysis into market shapes, such as ingots, wire bars, and cakes. Both furnaces are reverberatories of practically the same general design and are operated intermittently, putting through a charge normally in 24 hours. The treatment of the copper in both furnaces is similar, in so far that oxidation followed by skimming and reduction (poling) is carried on in both; but in the refined-copper furnace, the work must be done with greater care and it is of extreme importance that not the slightest trace of impurity be introduced into the copper. The furnaces usually hold from 150 to 300 tons of molten copper, which constitutes the daily charge. Except in the case of furnaces in the Lake district, where the concentrates from native-copper ores are charged through the roof, the furnaces are charged through the side doors by charging machines similar to those used in open-hearth steel practice. In 1916, at the Perth Amboy plant, of the American Smelting & Refining Co., located at Maurer, N. J., a study was made of the possibility of firing the copper refinery furnaces with pulverized coal instead of by hand. The proposed method possessed obvious advantages over hand firing and coal was a much cheaper fuel than oil at that time. It was realized, however, that there were several objections to its use, the principal ones being the liability of increasing the sulfur content of the refined copper, and the additional slag that might be produced from the ash. The increase of the sulfur content of the refined copper was the more serious, as more than 0.002 per cent. sulfur is objectionable. In the case of the slag, any increase would be expensive as the copper in this slag would have to pass again through the entire smelting and refining process.

Jan 3, 1925

By William J. Millard

The Island of Trinidad has much the same geological history as the continent of South America. There are present in this area Cretaceous, Tertiary and Quaternary rocks, which were deposited in a basin covering eastern Venezuela and Trinidad, very much as rocks of the same age were deposited in the Maracaibo Basin in western Venezuela. Along the north coast there are metamorphosed and semimetamorphosed Cretaceous rocks which are found as semicrystalline limestone, schists and quartzites, etc. Both the Cretaceous and Tertiary rocks are petroliferous and are responsible for the production of oil in Trinidad and eastern Venezuela. The geological column in the oil-bearing region of Trinidad is shown below.

Jan 1, 1931

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937

By M. H. Gaskell, D. C. Lindley

Small, steeply inclined reservoirs without natural water drives often are found associated with salt domes or other highly faulted structures. Frequently, only one well may be economically justified in these reservoirs, from which oil is produced by an expanding gas-cap drive or by a dissolved-gas drive. Although a large fraction of the oil upstructure from the well may be recovered during primary depletion, only a small fraction of the downdip oil can be produced because of gravity effects. This downdip oil has been defined as cellar oil991 in contradistinction to "attic oil" which is the oil above the structurally highest well in reservoirs where a natural water drive is present. In this study, two methods of producing cellar oil by water flooding a one-well reservoir were investigated by means of a laboratory model. This model was scaled to represent a prototype reservoir having an area of 30 acres, a permeability of 500 md, and a thickness and dip of 30 ft and 30°, respectively. One method considered, the simultaneous injection of water and production of oil from a single well, would require that the lower portion of the productive interval of a well be completed for water injection and the upper portion for oil production. The other method considered, intermittent injection, would involve alternate injection of water into and production of oil from a single well. Injection of water into the formation would repressure the reservoir, causing gas to go back into solution. Since some of the injected water would flow updip from the well, water injection usually would be followed by a waiting period during which the water could drain from above the wellbore. Production of oil by gravity drainage and gas-cap drive could be initiated when water drainage became sufficiently complete. The amount of water produced along with the oil would naturally depend on how soon after water injection ceased that production was started. This process could be repeated in cycles until oil could no longer be produced economically. Of these two methods, the intermittent injection technique would be simpler to put into operation since it does not require a dual completion. Also, it is probably more generally applicable than the simultaneous injection-production method. It is to be expected that in some reservoirs the rock and fluid properties would be such that practical oil-production rates could not be achieved by the simultaneous technique. However, in reservoirs where the simultaneous method will result in practical rates of oil production, it does have the advantage of permitting immediate, continuous oil production; whereas in the intermittent method, oil production is interrupted by periods of water injection and drainage. It was the objective of this study to determine whether these two methods of cellar oil production are practical for the representative prototype investigated and to evaluate their relative merits. DESIGN OF LABORATORY MODEL SCALING REQUIREMENTS The prototype reservoir and fluids were selected to have the dimensions and physical properties shown in Table 1. The laboratory model was then designed in accordance with well known scaling criteria, as discussed by Croes, et al,2 except for one modification. According to Croes, et al, one requirement of scaling a laboratory model to a reservoir prototype is that both the relative permeabilities and dimensionless capillary pressure be the same functions of water saturation for the model and the prototype. Since unconsolidated sand packs are used in the laboratory model to represent the consolidated porous media of the prototype, it is virtually impossible to satisfy this requirement. Much of the difficulty stems from the fact that unconsolidated sands usually exhibit lower residual oil and connate-water saturations than do reservoir rocks. To satisfy the scaling requirement as nearly as possible, Perkins and Collins' have suggested that the relative permeabilities be re-defined as

By K. A. Lambert

In the Anthracite Region there are considerable areas where the original mining was done 50 or more years ago. In this original mining, the pillars that were left proved inadequate in size for the support of the roof, which has since collapsed as a result of squeezes, and completely filled the original openings. In an endeavor to recover the coal which remains in the pillars in such areas, the reopening cost for development, as well as for pillar recovery, has been excessive in many instances. Various methods have been tried out with a view to lowering the cost, in order that the greatest possible percentage of recovery of the reserve tonnage may be realized economically. Ordinary hand mining necessitates the driving of development road 10 ft. wide in the clear between timber legs, with 6 ft. of clearance over the rail to accommodate mine cars; collars or crossbars on the timber sets have been difficult to maintain in these openings in the heavily caved condition, especially in beds where the overburden is great,. Numerous failures have occurred on these development road timbers because of roof movement resulting from removal of pillars. The actual removal of pillars from this development work has been costly because full-width openings for transporting mine cars to the face have to be maintained by cleaning caved material from alongside the pillars, or skipping up along the pillars where pillars of sufficient width are found. Shaker-chute Methods A method of developing such caved conditions and recovering pillars tributary to this development, utilizing shaker chutes, is being tried out with considerable success at Loree colliery. An outline of the chute and apparatus is shown in Fig. 1, which indicates the location of pillars and caved material. The cost of both labor and material required in the recovery of such coal is considerably less than by ordinary hand methods. In order to try out this method of mining a location was chosen where a tightly caved area had been developed by ordinary hand methods to within 300 ft. of the property line. The original bed height was 12 ft., with an overburden of 325 ft., but on account of the squeezes which

Jan 1, 1931

By R. G. Knickerbocker, R. R. Lloyd, W. T. Rawles

In July 1041, the Experiment Station of the Bureau of Mines at Boulder City, Nevada, began a study of methods of producing magnesium metal from magnesium oxide, with particular emphasis upon the direct use of magnesium oxide in a molten chloride electrolyte. The program was extended to include pilot-plant study of chemical methods for the preparation of pure magnesia from dolomites and magnesites. Preliminary work on the production of magnesia from dolomite was done with the cooperation of Kobert D. Pike and the Harbison-Walker Refractories Co. These investigatipns included a cooperative arrangement whereby the Bureau tested certain steps of the Harbison-Walker-Pike process. The process finally developed by the Bureau includes the precarbonation mixing step of the H.W.P. flowsheet prepared by Mr. Pike. Two magnesium-reduction plants using MgO as a source of magnesium were being constructed in the West, and they enormously stimulated interest in various dolomite deposits as possible sources of the magnesia needed by them. This paper describes one phase of this program—the operation of a pilot plant for producing cell-grade magnesia from dolomite from Sloan, Nevada. The process developed for this purpose is an adaptation of a well-known process first proposed by Clossonl and modified by others,2"1 involving the use of calcium chloride and carbon dioxide. It is based on the following chemical reactions: MgCl2 + Ca(OH)2 = CaCl2 + Mg(OH)2 [1] Mg(OH)4 + CaCU + CO2 = MgCl2 + CaCO, + H2O [2] The first reaction proceeds almost completely to the right because of the much greater solubility of calcium hydroxide as compared with magnesium hydroxide. Under equilibrium conditions, when only the four components shown in reaction I are involved, the ratio of magnesium to calcium in solution, according to solubility-product relationship, will be: This reaction is the basis of present commercial processes for recovering magnesium from sea water and dolomite. The second reaction is, in effect, a reversal of the first reaction produced by adding COz. This reaction also proceeds nearly to completion, the solubility relationship being: Ca where P indicates partial pressure of COz, in atmospheres.

Jan 1, 1944

By Oscar Kuchs

IN January and February of the current year, at the Tooele plant of the International Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast- furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of reverberatory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it was planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary: to install a bag house, a fan, and the necessary flues to complete the equipment.

Jan 7, 1914

By D. A. Dahlstrom

(A. C. Richardson and Charles C. Boley, presiding) W. E. BROWN*—In the operation of the cyclone, what factors have you found that will affect its results as far as efficiency goes; for example, if you have coming through the cyclone a pulp of 20 gpm, that has, say, 25 or 30 pct solids, and then from operational characteristics this pulp changes to 35 pct solids but it is still maintaining the same ratio of flow. HOW does that affect the cyclone;) D. A. DAHLSTHOM (author's reply) —It has a definite effect, as you know from Mr. Sutherland's paper,l3 in that as you increase the solid concerltration of your inlet slurry, you will naturally have an according effect on the overflow concell-

Jan 1, 1950

By M. L. Fuller

IN connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segre-gate structures of the Widmanstätten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith1 the plane of segregation in the matrix con-tains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the literature.2 The increasing com-mercial importance of zinc alloys containing copper makes this funda-mental study of value to the metallography of zinc alloys.

Jan 1, 1933