Search Documents

By H. H. Hausner, S. Storchheim, J. L. Zambrow

The solid state bonding of aluminum to nickel was studied as a function of temperature, pressure, and time at pressure. The initial results indicated that as the reaction conditions were varied, marked changes in tensile strength occurred. Plots of the log penetration coefficient vs the reciprocal of absolute temperature for various isobars were straight lines displaced from each other. THE techniques of bonding different metals to A each other include brazing, welding, welding by application of a molten phase, and solid state welding without any molten phase present. This last technique, the pressing of metals either at room temperature or at some temperature below the melting point of the metals to be joined, seems to offer interesting possibilities for bonding purposes. However, this technique has not been completely investigated, and very little is known about the diffusion phenomena which occur during solid state welding. Some previous work on the effect of pressure on diffusion1 was inconclusive. This paper is concerned with an investigation regarding the effect that the processing variables, such as pressure, temperature, and time at pressure, have in solid state bonding. The tests were made with aluminum and nickel and special emphasis was given to the strength of the bond between these two metals and to the intermetallic penetration rate during the bonding process. It seems that the effect of pressure on the intermetallic penetration is of particular importance for practical purposes and this effect was therefore studied in detail. Procedure Apparatus: The means of solid state bonding used for this study was that of the hot-pressing technique. This method requires the equipment pictured in Fig. 1 and involved the following procedure. The two metals to be bonded were placed in an aquadag lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diameter made of the same material. A thermocouple

Jan 1, 1955

AN excerpt from the Odessa Isvestia Vechernia, dated April 24, 1927, and translated by P. Routzitzky, summarizes a report by Professor Preobragensky ad-dressed to the Russian Government. Professor Preo-bragensky writes in regard to newly discovered potash deposits in eastern European Russia. Near Solikamsk in the Perm district, about 100 miles east of the Ural mountains and on the Kama river, large deposits have been located and the belt has been traced southward about 25 miles. Subsequently the search for potash salts has been transferred to the Berezovsky district, near Nikolsk, on the Kosva river, about 70 miles north-east-of the city of Perm. Toward the end of March, 1927, at a depth of 800 ft., drilling at the Levensk salt works revealed potash salts in, definite strata. The bed has a thickness which extends from a depth of- 245 to 307 meters (latest data in middle of April, 1927) and has not been bottomed yet. Professor Preobragensky goes on to say that these operations have definitely, developed very large de-posits, the limits of which are still unknown. There is at least an implication that the reserves far exceed those of Stassfurt, Germany. For European use they are, of course, much less accessible, for by through rail they lie 1200 miles east of Petrograd. Further, no particulars are given as to the potash content. It is to be supposed that the salt occurs in the Permian beds that extend north and south along the west flank of the Ural mountains, as the localities mentioned .all lie within the area so mapped on the new geologic map of Russia issued by the Scientific and Technical Di-vision of the All-Russian Council of Soviets in 1922. It is interesting to note that these salt beds are of the same geologic age as those of 'the Stassfurt region and of the west Texas-New Mexico district, in which the U. S. Bureau of Mines is at present drilling.

Jan 7, 1927

By M. T. Hepworth, R. Schuhmann

Hydrogen solubility measurements were made on a series of Ti-O alloys, and a portion of the 800°C isotherm for the Ti-O-H system was determined. Activities of oxygen and titanium were calculated from the experimentally measured activities of hydrogen, using ternary Gibbs-Duhem integrations. The data were extrapolated to obtain thermo-dynamic properties of binary Ti-O solutions. The thermodynamic properties of a Ti-0 solid solutions thus determined were compared with properties predicted from interstitial models. The Gibbs-Duhem equation, long used to calculate activities in binary systems, has been extended. recently to ternary systems.1"3 When the activity of one component in a ternary system is known as a function of composition, the activities of the other two components can be calculated from that of the first by an integration procedure, provided certain restrictions are observed on the path of integration. Often the activity of one component in a ternary system can be measured readily, while the activities of the other two components are difficult to measure. Gibbs-Duhem calculations are especially applicable to such systems. The further possibility arises of developing a new and indirect approach to activity measurement in binary systems. The proposed new method for binary systems consists of adding varying amounts of a third component whose thermodynamic behavior is easily measured. The activity of this added component is determined experimentally as a function of composition. Then the activities of the two components of the original binary system are calculated by Gibbs-Duhem integrations and extrapolations. For the work to be described in this paper, the Ti-0-H system was selected as a promising system for evaluating this approach. Investigations of the Ti-H system have shown that the activity of hydrogen can be measured precisely with little difficulty. Pure titanium transforms from a low-temperature a form (hcp) to a higher-temperature /3 firm (bcc) at 882.5"~ The phase transformation occurs in a temperature range where hydrogen pressures are easily measured. Also, the diffusivity of hydrogen at temperatures above 600" or 700"~ is large enough that equilibrium can be reached within a reasonable time.

Jan 1, 1962

By William E. Greenawalt

Ever since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydroelectric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods. Electrolytic methods are ideally adapted to hydroelectric development, for the load is constant throughout the full twenty-four hours, and the cost of both installation and operation of hydroelectric plants is not appreciably greater when operating for twenty-four hours than when operating for eight or ten hours; whereas, in fuel-power generation, as also in smelting, the cost is more or less in proportion to the fuel and power used. Nevertheless, fuel-power generation presents advantages in electrolytic methods, as the power plant may be located in a favorable place while the leaching and electrolytic plants may be located at the mine. The ultimate possibilities of the wet methods have yet to be determined. The possibilities of smelting have been thoroughly worked out; there is no unsolved major problem in copper smelting, and it has practically reached the limit of its possibilities. It seems hardly probable that any future improvement, either of method or apparatus, will greatly

Jan 1, 1924

By Fred P. Dewey

Although coke is the acknowledged metallurgical fuel, and has been extensively used in this country for more than thirty years, yet the facts on record in regard to its physical properties are exceedingly meagre; and this is also true, but in a less degree, of its chemical composition. An investigation is being carried on in the National Museum which is intended to supply, so far as may be, this deficiency, and through the kindness of Professor Baird, Director of the Museum, I am permitted to present to the Institute a summary of a portion of the results already obtained. So far as I am aware, the credit for the first systematic investigation of the physical properties of coke belongs to Mr. John Fulton, Mining Engineer of Cambria Iron Co. The results of this investigation have been published in Report L, Second Geological Survey, Pennsylvania, 1875, and in a pamphlet setting forth the advantages of the Connellsville coke, the latter published also by the " Virginias"* His results are not altogether free from experimental errors, and the assumption that "the specific gravities of coke and water are very nearly alike "- is scarcely warranted. It has seemed to me, therefore, desirable to make an independent investigation of the physical properties of coke on a plan somewhat different from that adopted by Mr. Fulton. This is the investigation now being carried on at the National Museum.

Jan 1, 1884

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By William Kent

A MOST startling and as yet unexplained, failure of steel boilerplates, in two different sets of boilers, is reported in a paper by Arthur J. Maginnis, published in the London Engineer, December 11th, 1885, and reprinted in the American Engineer, January 14th, 1386. The facts of the case, as condensed from Mr. Maginnis's paper and from a number of letters in the subsequent issues of the Engineer, are as follows: 1. The material used for two different sets of boilers on two different steamers, each set consisting of three circular boilers with horizontal steam-chests, passed all tests required by the Board of Trade

Jan 1, 1886

By J. B. Austin

It is now well established, chiefly through the work of Davenport and Bain,' that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 on page 295 and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low—that is, the metal offers little resistance to a change in lattice—but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way, the time required for one coulomb to pass a given point (1/I) is equal to R/E. If the temperature of the whole circuit is changed, the resultant change in 1/I will depend on the relative rates of change of R and of E,

Jan 1, 1935

By J. B. Austin

It is now well established, chiefly through the work of Davenport and Bain,' that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 on page 295 and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low—that is, the metal offers little resistance to a change in lattice—but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way, the time required for one coulomb to pass a given point (1/I) is equal to R/E. If the temperature of the whole circuit is changed, the resultant change in 1/I will depend on the relative rates of change of R and of E,

Jan 1, 1935

By R. W. Bartlett

Hydrometallurgical processes for copper flotation concentrates avoid the SO2 emission problems associated with smelting, but they require oxidation of copper to obtain solubilization during leaching. The resulting copper ions must be reduced to metal, which normally requires large amounts of energy or energy equivalent reagents such as hydrogen or iron. The conventional reduction method is electrowinning which is labor intensive and involves 35 to 40% of both the entire operating and capital cost of the better hydrometallurgical processes. There is considerable incentive to reduce the cost and energy required for producing copper ions from solution. Furthermore, it is thermodynamically possible to do this using sulfur contained in the concentrate itself. In fact, the thermodynamic potential of oxidizing sulfur from S+4 to the S+6 state is greater than required to reduce cupric ion to metallic copper.1 Realization of this potential in a practical process would significantly reduce the cost of hydrometallurgical processing of sulfide concentrates because sulfur would become a cost-free reducing agent. An apparently practical method is to use SO: and HSO3 ions, obtained by ammonia scrubbing of SO2 from a concentrate roaster gas, to reduce leached copper to metal in an autoclave. This reduction step is the Jumau 1907 A series of steps, including sulfite reduction, constituting a crude flowsheet was suggested by Parker in 1976.3 The present paper describes a detailed complete. sulfite process flowsheet based on materials and energy balances, discusses the chemistry, and discusses further work that is required to develop this process. Process materials, utilities costs, and energy requirements are projected to be unusually low because of the utilization of sulfur from the concentrate. Process Description The sulfite reduction process requires a copper concentrate containing approximately as much sulfur on a weight basis as copper. For those few concentrates that are deficient in sulfur, additional sulfur can generally be obtained by allowing more pyrite to float in the concentration process. The process steps, shown in [Fig. 1], are (1) a fluid bed roast of the concentrate, (2) a leach of the roaster calcine using recycled barren liquor from the reduction autoclave, (3) scrubbing of the SO2 gas with ammonium sulfite liquor to produce ammonium bisulfite, (4) reduction and precipitation of copper in an autoclave by combining part of the SO2 scrubber effluent (SO5

Jan 1, 1980

By Walter E. Duncan, Oscar F. Tangel, A. M. Gaudin, Franklin Dewey, R. A. Johnson

Xanthates have been used as collectors of sulfide minerals in the concentration of ores by flotation for over a decade, yet much remains to be done to elucidate the underlying reasons for the remarkable effectiveness of these compounds in this connection. Briefly stated, the known facts concerning the effect of these reagents on the floatability of minerals are as follows: 1. Xanthates are without effect on silicates, silica, and generally on minerals currently regarded as "gangues." 2. Xanthates in very small amount increase enormously the floatability of sulfides of copper, lead, silver, iron and mercury. 3. If zinc sulfides are first '(activated," as by treatment with a copper salt, they are readily floated by xanthates; otherwise not. 4. Elemental copper, silver and gold have their floatabilities increased by xanthates. 5. Sulfides of elements that are not typically metallic—e.g., stibnite, realgar, molybdenit—are not made to float markedly better by treatment with xanthates. 6. Oxidized minerals of lead and copper are floated if treated with large amounts of xanthates, but not so if treated with amounts of the same order of magnitude as required for sulfide flotation. Oxidized zinc minerals are not floated unless xanthates having unusually long hydrocarbon chains (e.g., eight carbon atoms or more) are used. Iron oxides and carbonate are not floated by xanthates. From a flotation standpoint the most striking feature about xanthates is the very small amount required to accomplish startling changes in the behavior of some minerals. The amounts used in practice to effect excellent concentration are frequently of the order of 0.05 lb, of agent per ton of ore; that is, of the order of one part of agent per forty thousand parts of ore. Changes in amount of agent of the order of 0.01 lb. per ton of ore (or 0.002 lb. per ton of pulp, on a 4:l basis) have marked effects on the metallurgical results obtained. Yet these changes represent a variation of but one part per million parts of pulp.

Jan 1, 1935

By Arthur Notman

(San Francisco Meeting, September, 1915) SACRAMENTO HILL is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the mass of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chalcocite with associated carbonates as stringers in a mass of strongly brecciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or so places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface observed in the other disseminated deposits of the Southwest.

Jan 8, 1915

By Arthur Notman

SacRamento Hill is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the masa of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chal-cocite with associated carbonates as stringers in a mass of strongly brccciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or SO places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface obscrved in the other disseminated deposits of the Southwest.

Jan 1, 1916

As a service to its readers, MINING ENGINEERING is publishing the mineral industry portion of the 1952 list of "Accredited Undergraduate Engineering Curricula in the United States." This list, revised annually, is issued by the Education Committee of the Engineers Council for Professional Development, and covers all phases of engineering education. The AIME is actively represented on ECPD, which was jointly organized by the Founder Societies and various other groups interested in the professional recognition of engineers.

Jan 4, 1953

By Sir John Cadnan

The production from the Maidan-i-Naftun area for the year ending March, 1928, was 5,340,000 tons (40,210,200 bbl.), an increase of nearly 13 per cent. over the production for the year ending in March, 1927. The production by years since the opening of the field in 1912 is given in the following table: [1 ton = 7.53 bbl.] Year Ended MaRch Tons Year Ended March Tons 1912 (7 months)............. 43,084 1920....................... 1,354,631 1913........................ 80,800 1921....................... 1,767,070 1914........................ 273,635 1922....................... 2,310,098 1915........................ 375,977 1923....................... 2,913,908 1916........................ 449,394 1924....................... 3,583,000 1917........................ 644,074 1925....................... 4,221,000 1918........................ 897,402 1926....................... 4,470,000 1919....................... 1,081,919 1927....................... 4,735,000 1928....................... 5,340,000 The actual production represents only a small proportion of the potential production. The Masjid-i-Suleiman Field The present producing unit, the Masjid-I-Suleiman, is an anticline some 20 miles in length by 4 miles in width, including three domes as so far proved. The producing horizon is a very open, dolomitic limestone, which, while showing much variation in texture and porosity, is so connected that the lowering of pressure in one section of the field quickly affects the whole area. The topography of the field is broken, with differences of well elevations of as much as 1100 ft. The depths to the limestone vary from about 800 to about 5000 ft. The closed-in pressure of the oil wells varies from zero to 50 lb. per sq. in. and that of the gas wells is about 450 Ib. Although the static oil level may be several hundred feet below ground level, in oil wells of high elevation, all the wells flow continuously or intermittently after they are once started—the majority continuously. The gas is very high in hydrogen sulfide in gas-oil wells of low pressure.

Jan 1, 1929

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

By Robert H. Leach

SILVER the whitest of all metals, has been used for thousands of years. Students of antiquity agree that silver, gold, copper, and their alloys were the first metals discovered by man and they have all played an important part throughout the advance of civilization. Native silver has been found in different parts of the world in varying form and size, such as clusters of fine wires in rock cavities, thin sheets along cleavage planes in veins of rocks, and pieces of irregular shape that vary in size from extremely small particles to masses weighing many pounds. Nearly pure silver is found in, the native state but the native metal is more likely to contain copper or gold. Some of the natural alloys closely approximate the compositions of synthetic alloys that are used in the arts at the present time. As these native silver alloys usually are malleable and ductile, it is evident that prehistoric man was provided by nature with metals that he could work, with the crude tools at his command, into simple ornaments or other articles. The relative scarcity of silver combined with its resistance to attack under ordinary atmospheric conditions have been important factors in determining the purposes for which man has used it. Its scarcity and indestructible character have made its possession particularly desirable, and from the earliest times its principal use has been as a measure of wealth and a medium of exchange. The comparatively high value of silver in relation to other commodities makes it possible to transport a large amount of wealth in small bulk, and silver has traveled back and forth over all parts of the world. Even when made into ornamental pieces, such as bracelets,

Jan 1, 1953

By R. P. Agarwala, M. S. Anand, S. P. Murarka

Using the residual radioactivity technique, grain boundary diffusion of chromium in the a phase and lattice diffusion in the a and the ß phases of zirconiuttz have heen studied. The diffusivities (in units of square centiwzeters per second) have heen expressed as THE rate of diffusion of atoms along surfaces and grain boundaries is much greater than that through the bulk of metals. These processes dominate over volume diffusion at lower temperatures and can be isolated from it by virtue of the fact they yield high diffusion coefficients and low activation energies. In zirconium, however, it has been difficult to identify the volume-diffusion parameters separately. The values of diffusivities in a and ß phases yield activation energies which are much lower than those for volume diffusion calculated from semiempirical or empirical relations.1-3 Diffusion frequencies (Do) are also low, especially in the a phase, and they yield negative entropies of activation.4 Similar results have been obtained for the diffusion studies in titanium.5 It is yet to be investigated whether in these cases diffusion is controlled by some extraneous factor like high reactivity of these metals, or some different mechanism is operative as suggested by Pound et a1.6 However, Federer and Lundy,7 in a recent study of the diffusion of zir-conium-95 and columbium-95 in zirconium, and Gibbs et al.,8 in the study of impurity diffusion in titanium, found a temperature dependence of D, Do, and Q. Their study yielded low values of Do and Q at low temperatures, as has been found by other workers, and fairly high values at high tempera-

Jan 1, 1965

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

By Richard W. Smith

There are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual product of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue" rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties—by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as could be expected without railroad transportation. In January, 1896, Judge S. Q. Weatherly, who was interested in the development of the blue phosphate, while riding along the road south of Mt. Pleasant, noticed some slabs of a brown rock in place above the limestone. He took samples, and had them analyzed, thus discovering the high-grade brown phosphate of this district. This discovery was kept a secret until July, 1896, when mining was started at the village of Mt. Pleasant. Development proceeded rapidly, many owners obtaining their capital by the sale of their rock fences, which were largely composed of slabs of high-grade brown phosphate. The development of the brown rock, which is richer and more easily mined than the blue, caused Tennessee to advance from a poor third in production to second, surpassing the output of South Carolina, and being excelled only by Florida.

Jan 1, 1927