Search Documents

By Y. C. Kim, C. B. Manula

This paper is concerned with the details of the derivation of an operations research model, specifically linear programming, to solve production scheduling problems. While some results are presented for an actual study, the calculation of cases of a more general nature have not yet been completed. Production managers from those segments of the mining industry that experience a seasonal or highly variable sales demand find it rather difficult to develop overall producing plans for their organizations. In an attempt to solve this technical problem, demands are usually met by keeping production corresponding exactly to sales. This results in a fluctuating production schedule which is costly to maintain because of overtime premiums in periods of high requirements and because of costs associated with an idle mine plant during slack periods. An alternate solution may be to produce part of the desired amount and make up any deficiencies by using overproduction in previous time periods. This tends to smooth the production pattern through the use of a stockpile. However, because of associated storage costs, the solution may again be undesirable if it yields comparatively large surpluses. In general, this type of scheduling problem has an infinite number of solutions which satisfy the requirements. These are largely dependent on the extent to which an operation is geared to changes in production and on the size of its stockpiling facility. The determination of an efficient schedule is implied, therefore, as one lying between two extreme solutions, i.e., one that minimizes surpluses and one that minimizes output fluctuations. These conflicting objectives result in an economic balance problem between the costs of carrying surpluses forward from slack periods versus the cost of high production levels during peak demands. Various methods of operations research have been developed to handle problems whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. Those who are familiar with mining operations know that most managers have not progressed satisfactorily in this area. Production planning systems which most mines employ today are often no more than rough records of management's mental planning. For small mines these means are normally sufficient; but as operations grow larger and become more complex, this type of planning ability is no longer adequate. Managers may find themselves losing control of cost relationships, taking longer to outline production sequences, and becoming forgetful of certain resource availabilities. ORIGIN AND SCOPE OF A SCHEDULING PROBLEM The more fundamental aspects of the production scheduling problem can be brought into focus by demonstrating how it exists in a bituminous coal mine* located in southwestern Pennsylvania. This mine, operating in the Pittsburgh seam, uses a definite room-and-pillar block system of mining, which is planned and carried out with only slight variations to meet local conditions. The coal seam, which is firm and varying in thickness from 8 to 9 ft with the bottom 6% ft being extracted, is under 500 ft of cover and opened by a shaft. The bulk of the coal (60%) is obtained from the pillaring activity with the mains and sections, which are considered primarily as development activities, contributing the balance of 12% and 28%, respectively. All coal is won by a ripper-type continuous miner in conjunction with shuttle-cars directly behind a loading machine. Track haulage is employed to move coal from these machine centers to the shaft bottom. The coal, thus mined, is shipped to one destination as part of a mixture of coals to be used in the making of steel. A material flow diagram of this distribution scheme is illustrated in Fig. 1. PROBLEM STATEMENT From the above types of shipments and mining limitations, the basic problem is to determine an economic means of producing and stockpiling a single coal product produced in three different machine centers (main, section, and pillar). Fig. 2 shows total demand for coal as a function of time. Because of the extremely high peak demands, slack period production must be stored and then distributed

Jan 1, 1969

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken's method1' for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By F. A. Hames, D. S. Eppelsheimer

The ferromagnetic copper-manganese-aluminum and copper-manganese-tin alloys (Heusler alloys) owe their ferromagnetism to the beta phases (body-centered cubic structure) in their respective systems.l,2,3 The ternary beta phase regions in these systems are extensions of the beta fields of the binary copper-aluminum and copper-tin systems into the ternary models of the copper-manganese-aluminum and copper-manganese-tin systems respectively. X ray analysis has indicated the presence of long-range order in the more strongly magnetic alloys.3,4,5 The ideal ordered structure is obtained in alloys of compositions Cu2MnAl and Cu2MnSn; the copper atoms occupy positions at cube centers while the aluminum (tin) and manganese atoms alternate at cube corners. This atomic arrangement is illustrated in Fig 1. The compositions Cu2MnAl and Cu2MnSn are also those that show maximum magnetic saturation moment. 3,4,6,7 Departures from these compositions result in a decrease in the degree of order attainable and a decrease in magnetic saturation moment. In view of the chemical similarities of aluminum, tin, indium, and gallium, and the existence of beta phases in the binary systems copper-indium and copper-gallium, it may be suspected that ternary beta phases exist in the systems copper-manganese-indium and copper-manganese-gallium, and that these are ferromagnetic. The purpose of this investigation was to determine whether ferromagnetic beta phases exist in the systems copper-manganese-indium and copper-manganese-gallium analogous to the ferromagnetic beta phases in the systems copper-manganese-aluminum and copper-manganese-tin. Previous Work At the time this investigation was started no information could be found regarding the constitution of copper-manganese-indium and copper-manganese-gallium alloys, nor of the binary manganese-indium and man-

Jan 1, 1950

By I. R. Dunlap, R. F. Burdyn, F. D. Patchen

The composition and properties of a new type of cementing mixture are discussed. In these compositions, API Class A or C cements are added to n stable water-in-oil emulsion instead of the crsual water. The cement disperses in the oil phase and remains out of contact with the water under normal conditions of mixing and storage. At higher temperatcrres, such as those encountered down-hole during placement, the emulsion breaks and cement hydration can then proceed. An extremely low filtration rate is obtained; the major part of the filtrate is oil. Thickening times of the mixture may be increased to meet the 18,000-ft casing cementing schedule by varying the amount of emzilsifier. As in conventional Portland cement mixtures, high-temperature strength retrogression can be overcome by addition of silica flour. Results of several field app1ication.r show that mixing presents no diffculty if emulsion blenders are used and the emulsion is prepared beforehand. INTRODUCTION Water-in-oil emulsions., in which oil is the continuous or external phase and in which water exists as discrete droplets, have for some time been used successfully in drilling muds to reduce filtration loss.1,2 Applied to cement slurries, the same results are obtained; i. e., the fluid-loss is greatly reduced. In addition, thickening times may be extended, lower densities and strengths obtained, and water-base borehole fluids more easily displaced without contamination of the cement. A low filtration rate is often a desirable property in oil well cements since loss of fluid increases placement difficulties and may also cause damage to water-sensitive producing formations.' In the casing cementing operation where the cement slurry is pumped into the narrow annulus between open hole and casing, rapid loss of fluid to a porous formation can cause the slurry to thicken and plug the annulus before the desired fill is obtained. Where a casing or a liner is cemented against a productive formation and the well completed through perforations, the fluid lost between the time the cement first contacts the formation and the time a set is obtained may invade the zone past the depth of the perforations. If the sand contains a material which will swell upon contact with cement filtrate, permanent damage may result. Previous methods for reducing the fluid-loss of cements have employed bentonite4 as an additive, usually with a lignosulfonate as a dispersant, or a derivative of some naturally occurring polymeric material such as cellulose ether." Oil emulsion cements have also been proposedv or fluid-loss reduction, but these have been of the oil-in-water type. Bentonite cements have been used most widely and have been successful in reducing incidence of premature setting of cement attributable to loss of water by filtration. It is the purpose of this paper to describe preparation and properties of a water-in-oil emulsion cement and to relate procedures followed and results obtained in several field applications. DESCRIPTION OF SYSTEM AND MECHANISMS A water-in-oil emulsion cement is prepared by adding an API Class A or C cement to a stable water-in-oil emulsion. Fig. 1 is a photomicrograph of this emulsion before addition of cement. Here the droplets are water and the surrounding medium is diesel oil. High emulsion stability is indicated by the small droplet size [1-5 microns], and by their uniformity.' To form a stable water-in-oil emulsion as illustrated, several conditions must be met. A predominantly hydrophobic emulsifier must be present in sufficient concentration to produce a strong interfacial film; initially, the phase volume ratio (the water-to-oil ratio) must be low;

By L. J. Lorig, B. H. G. Brady

The Discrete Element Method is a numerical technique suitable for use in modeling the discontinuum behavior of jointed rock. The disadvantage of this method, in its application to analysis of underground excavations, is the necessity to discretize the complete problem domain. Since the far-field rock responds to the excavation as an elastic continuum, it may be appropriately represented by the Boundary Element Method. This exploits the inherent advantage of the Boundary Element Method in representing a quasi-infinite domain in terms of its internal surface geometry and associated boundary conditions. The procedures employed in developing a first-generation coupled Discrete Element-Boundary Element algorithm are described and the solution to a simple problem verifying the performance of the coupled code is presented. A procedure for numerical treatment of installed support systems is also presented.

Jan 1, 1982

By H. C. Chang, N. J. Grant, A. R. Chaudhuri

During the creep of coarse-grained polycrystalline magnesium at elevated temperatures, a nonbasal type of slip was found to play an important role in the deformation processes. The nonbasal slip traces were examined metallographically in eight specimens (13 grains) and the observed glide plane located stereographically for each grain. The tests were run at 500&apos; and 700°F at stresses of 148 to 786 psi. Based on these measurements and theoretical calculations, the crystallographic elements for nonbasal slip were determined. WHEN a metal deforms by slip, the conventional appearance of the slip bands on the surface of a specimen is that of straight lines. Such is the behavior of the face-centered-cubic metals, as for example, aluminum. The particular slip system on which slip occurs in these metals is governed by the criterion of resolved shear stress. Work on the body-centered-cubic metals a-iron,&apos;. &apos; molybdenum, and columbium4 has shown that the process of slip is somewhat more complicated than the simple gliding of one close-packed plane of atoms over another in a close-packed direction and that it results in the formation of wavy and irregular slip traces on the surface. The recent reviews and experiments of Vogel and Brick and Chen and Mad-din3 show that, for the body-centered-cubic metals, the resolved shear stresses along the planes and the degree of close-packing do not necessarily determine the slip system. Theirs and other investigations indicate that a complete understanding of the slip process in the body-centered-cubic metals is not yet possible. However, one behavior displayed by all these metals is that the slip direction is invariably one of the close-packed directions <11l>. The wavy nature of the slip-band traces has been explained on the basis of cooperative slip by planes sharing this same slip direction.1&apos;3l&apos; It is generally acknowledged that, when the hexagonal-close-packed metal magnesium (axial ratio c/a = 1.624) deforms by slip at room temperature, it does so by basal slip in the close-packed direction <1I%>. This type of slip has the conventional appearance of straight lines and is governed by the critical shear-stress law. Schmid and coworkers" showed that basal slip was operative in the temperature range of —185" to 300°C (—300" to 572°F). Work by Servi, Norton, and Grant6 has shown that, during the creep of coarse-grained aluminum at high temperatures, new slip systems come into operation. The existence of a new high temperature slip system at temperatures greater than 225 °C (437°F) for magnesium was suggested also by Schmid. This was later indicated by Bakarian and Mathewson&apos; to be slip along the pyramidal planes (10i1) in the close-packed direction <11%>.* They * Mention will be made in the text of pyramidal planes and prismatic planes. The pyramidal planes referred to are the type I. order 1 of the form {10il); and the prismatic planes of the type 1 of the form (10i0). For the sake of brevity, they are termed in the teat as pyramidal (10il: and prismatic (10i0) planes, respectively. Where reference is made to the pyramidal plane type 1, order 2 of the form {10i2), they are referred to as the pyramidal planes of the type (10i2:. observed that this kind of slip resulted in irregular markings on the specimen surface. According to them, a possible cause for the appearance of the markings was due to "limited accessory slip on the pyramidal {10i2) planes." Burke and Hibbard," on deforming a single crystal of magnesium at room temperature, found evidence of slip on a pyramidal plane {1011). They explained it as being due to the effect of grip restraints. It is pertinent to note at this point that, although basal slip has received a fair amount of attention, only two specimens have been investigated, that of Bakarian and Mathewson and of Burke and Hibbard, to establish the elements of nonbasal slip in magnesium. During the study of the deformation mechanisms

Jan 1, 1956

By Wilbur T. Stuart

To assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere.

Jan 2, 1955

By R. M. Wilhelm

HIGH-TEMPERATURE thermometry,, as treated in this paper, deals with the measurement of temperature in the range 100° to 550° C. The lower limit corresponds to the temperature of boiling water at normal atmospheric pressure, the upper limit is approximately the highest temperature to which mercury in a glass thermometer may be safely subjected.1 In this range., the domains of pyrometry and thermometry overlap somewhat, for high-temperature resistance thermometers and thermocouples generally classed as pyrometers are often used below 550° C. This paper will be confined to high-temperature mercurial thermometers, and indicating and recording thermometers of the vapor pressure, liquid or gas filled, and bimetallic or graphite-metal expansion types, a classification of which is as follows: CLASSIFICATION OF THERMOMETERS GENERAL CLASSIFICATION SUBDIVISIONS Mercury in glass Laboratory- Etched or engraved stems (mercurial) Enclosed scale (Einschlus) Industrial Vapor pressure Indicating and Pressure Liquid filled recording Gas filled Bimetallic Graphite-metal expansion

Jan 9, 1919

Discussion of the paper of M. E. Lormbardi,. presented at the New York meeting, February, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 209 to 215. I. N. KNAPP, Ardmore, Pa.-Some years ago I made a swinging spider to carry a string of casing in a way somewhat similar to that described in this paper. The ground I tried it in was too soft for its successful operation. The spider had a central one-flange bushing to carry the slips. Under this flange and on top of the spider was a properly protected ball runway, or ball bearing, which permitted rotating the casing when it was in place and supported by the slips.

Jan 5, 1915

By H. C. Goodrich

AT THE Utah Copper mine, steam shovels were first used, in 1906, for the removal of overburden, and in June, 1907 for the mining of ore. Prior to 1907, the ore came from underground development work and from stoping. The use of the steam shovel gradually increased until 1914; since then all material, both overburden and ore, has been loaded by power shovels operating on the various benches of the mine. During FIG. 1.-SCENE OF UTAH COPPER MINE BEFORE OPEN-PIT MINING WAS BEGUN. these 19 years, there has been a great improvement in open-pit mining; largely in the use of equipment having greater capacity and dependableness. The history of the development of mechanical shovels and related equipment, as affecting the Utah Copper Co., would be interesting and would justify considerable space; but of greater interest at this time is the operation of the equipment now in use. The Utah Copper mine is in a great deposit of copper-bearing monzonite, which occurs as a prominent headland of the Oquirrh range of

Jan 9, 1925

By H. DeWitt Smith

THE disastrous effect of two major wars on foreign economic health is giving American capital opportunities which might have not otherwise developed. At a time when discovery of major orebodies in the United States awaits fuller application of new geophysical tools and technical methods, U. S. investors must seek other fields where investment may be put to work. The unsettling effects of war have made it almost impossible for foreign nationals to develop mineral wealth, permitting Americans to enter at a time when U. S. mining, with a few exceptions, is in the process of expanding known orebodies and developing only a few new ones. Available capital, however, is not the only pre- requisite for entering the foreign mineral development field. The capital must be able to work in favorable economic atmosphere, a condition not easily satisfied in a world constantly in a state of political and social flux. In many countries, the political theory changes as often as the wind direction in March. Thus, the political stability of the form of government is of prime importance to the investor. In addition, a balanced budget and a moderate tax structure are important. Because in making foreign investment it is inevitable that one will have dealings with government officials, it is basic that they must be of high integrity. In countries filling the requirements, it will usually be found that the economic initiative of the individual is respected. Newmont Mining Corp.&apos;s three major investments in the last 15 years have been in Canada and the

Jan 1, 1952

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By A. E. Schuetz, A. E. Roswell, W. R. Hibbard

THE drawn wire texture of body-centered cubic iron,&apos; tungsten,&apos; and molybdenum~ as been determined to be a [110] direction parallel to the wire axis. The purpose of this study is to extend the available information on body-centered cubic wire textures to other metals and alloys. Wires were produced using hand wire rolls and dies as given in Table I. In addition, attempts were unsuccessful to draw wires from chromium, vanadium (Vanadium Corp. of America), and tungsten (Cleveland Tungsten Inc.). Although it is known that wires can be made from these materials, suitable techniques were not readily adaptable. Where necessary, wires were polished and etched to form flat ribbons 0.005 to 0.007 in. thick, and transmission X-ray patterns were taken using molybdenum radiation with the specimen tilted 0 degrees from the perpendicular toward the beam to critically cover the wire axis. Analyses were made of (110), (002), and (112) reflection circles. In all cases reflection maxima indicated the texture to be a single [1101 deformation fiber, as illustrated by Fig. 1 for molybdenum. In the case of the hot-worked ß brass, a second texture, [loo], was also found, but this is believed to be the result of recrystallization since it has been reported for re-crystallized molybdenum wires&apos; and it was not present in the cold-drawn ß brass. The difference in drawability between the 51.92 pct Cu ß brass and the 62.5 pct Cu ß brass (containing some grain boundary a due to incomplete quenching) is quite striking, since the latter could be cold worked readily while the former had to be hot worked to avoid cracking. Summary The deformation texture of drawn body-centered cubic wires of ß brass, iron, molybdenum, niobium, and tantalum is essentially a single [110] fiber as predicted by theory.&apos; Acknowledgment The authors wish to thank the suppliers of the metals listed in the text, and the Grant-in-Aid from the Research Fund of the Society of the Sigma Xi and Scientific Research Society of America which made possible the purchase of X-ray equipment.

Jan 1, 1952

By Morgan Walker, C. D. Watson, Reid W. Bond, D. L. Trax

Common practice in the Mid-Continent until recently was to prolong the natural flow of oil wells as long as possible by agitation, and then swab for a short period until the well was put on the pump. Comparatively recently the gas-lift has superseded the swabbing and agitating period and in some cases encroached on the natural flowing life, particularly where it was evident that the potential oil capacity of the well was greater than the gas supply, or lifting medium. The majority of wells are finished with either 6¼, 65/8 or 8¼-in. casing and connected to a separator through a flow line which is usually 65/8 in. The flow line is generally designed to eliminate sharp turns and has reduced the gas-oil ratio and therefore increased the efficiency in a good many instances. Until recently all wells were allowed to flow without restriction against the possible trap pressure until it was deemed advisable to put them on gas-lift. This resulted in a fairly efficient flow during the early life of the well if the well was rather large but was usually inefficient in small wells and in the later flowing life of large wells, on account of the large area in the casing and therefore excessive slippage. Recently, considerable effort has been made to increase the efficiency of small flowing wells by running tubing to eliminate as much slippage as possible. With large wells there is a considerable trend toward back-pressuring, or beaning to find out whether it is possible to reduce the gas-oil ratios and increase the flowing life. The greater number of fields that have been back-pressured have been produced in that manner through necessity, either to restrict production for proration purposes or, in fields producing by hydraulic pressure, to reduce water encroaching. The recent Cromwell sand development in Little River is an example where both back-pressuring by means of high-pressure traps and beans and flowing through tubing were used to conserve gas, reduce the high gas-oil ratio and prolong the flowing life. It

Jan 1, 1930

By Lawrence Burkhart, S. B. Joo

A hemispherical, constant volume drop with forced internal circulation was considered as a model approximating a real drop at a similar stage of formation Axially symmetric steady flow within a drop contaminated by surfactants was described by solving the full Navier-Stokes equations written in terms of a meridian plane stream function Rotational flow occurred inside the drop above a computed Reynolds number of 5.8, and the change in interfacial flow caused by imposing a surface-tension gradient at the surface had a significant effect on the internal flow Although the work is quite fundamental in nature, the rotational flow described in the paper is responsible for much of the bulk transport of solute to the interface in hydrometallurgical processes such as solvent extraction.

Jan 1, 1981

By A. B. Parsons

PUBLICATION of this little volume is a luxury that the Institute itself could scarcely afford. In truth, no engineer nor geologist, no assayer nor metallurgist would be likely to enhance his knowledge, improve his technique, or cut his own operating costs by reading this excellent translation of two booklets first published circa A.D. 1520. It is doubtful if the present enterprise would, in a practical or tangible way, "promote the arts and sciences connected with the economic production of the useful minerals and metals." And such, is the prescribed purpose for which the funds of the Institute should be spent. Fortunately for the Institute, the Seeley W. Mudd Memorial Fund is not so circumscribed; and the Fund Committee enjoys, greater liberty of action. The sponsorship by the Mudd Fund in 1942 of the publication of The Pirotechnia of Vannoccio Biringuccio, as translated by Dr. Smith and Mrs. Gnudi, was an innovation-indeed something of an experiment. Not only was the content of the volume significant mainly for its "cultural" and "scholarly" attributes; -but the format, an outstanding example of the fascinating art of bookmaking, bore no resemblance to the ordinary technical book. The Committee, frankly, was surprised at the enthusiastic reception accorded the volume. When a second edition was required, the Committee became convinced that the publication of material of this type, particularly if printed and bound in attractive form, was an appropriate avenue for utilizing a moderate proportion of the monies available from the Fund. The Bergbüchlein and the Probierbüchlein antedate by some years the first publication of De la Pirotechnia and of De re Metallica; but Georgius Agricola, the author of the latter work, made good use of the material in the earlier volumes. As pointed out in the Introduction, both

Jan 1, 1949

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By Charles P. Williams

THE determinations of the specific gravities of a number of samples of lead produced in Missouri, which form the subject of this note, were undertaken with the view of ascertaining if any approximation to the purity of such leads could be reached in this manner. The results would seem to indicate that, whatever value the method may have in the case of the crude and more impure

Jan 1, 1877

By Jack R. Dymond, Ronald G. Senechal, Robert O. Rye, Cyrus W. Field, Joseph F. Whelan

Metalliferous sediments are present through- out much of the ocean basins and are locally prominent in the sedimentary column on and near the Nazca plate of the east-southeast Pacific Ocean. They typically have anomalously high concentrations of the transition metals, and those on parts of the East Pacific Rise, the Bauer Deep, and other basinal depressions may contain more then 12% iron, 4% manganese, 0.1 % each of copper and nickel, and geochemically significant amounts of zinc, cobalt, molybdenum, arsenic, beryllium, silver, and possibly gold. Statistical interprerarions of chemical data indicate that most metals in sediments on the East Pacific Rise were derived from a hydrothermal component related to submarine volcanism, whereas those in basinal sediments accumulated from both hydrothermal and hydrogenous components of sedimentation. However, concentrations of the metals are controlled more by the absence of biogenic and detrital components than by nearness to centers of hydrothermal activity.

Jan 1, 1983

By Joseph Pogue

THE writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, FIG. 1.-SKETCH MAP SHOWING APPROXIMATE LOCATIONS OF ALL IMPORTANT EMERALD MINES AND PROSPECTS IN COLOMBIA. (Data in part supplied by Robert Scheibe, July, 1915.) Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year&apos;s duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 5, 1916