Search Documents

By Orville R. Lyons

THE continuous vacuum filter, whether it be a vertical or horizontal disk, inside or outside drum, when properly applied is a very effective device for dewatering fine solids. Because of the number of variables that affect its performance, however, it is not possible to obtain consistently maximum moisture reduction in an operating plant. This paper presents a method for determining the average cake moisture and the variations in cake moisture to be anticipated when dewatering fine solids by continuous vacuum filters under normal operating conditions. Previous investigators1,2 have found that certain factors influence filter performance, drum or disk diameter, speed of rotation, percentage of immersion, and the percentage of solids in the feed influence capacity. Blinding of the filter cloth reduces effective vacuum, produces a wetter cake, and may decrease capacity. Reduced vacuum or improper adjustment between vacuum and blowing portions of the cycle will produce a wetter cake and also may decrease capacity. Widely fluctuating feed tonnages will adversely affect cake moisture and capacity. Flocculation, when properly applied, increases capacity and reduces cake moisture. Without flocculation, the slimes are the first particles sucked to the filter medium, which becomes partially blinded in consequence. With flocculation, the flocs act as coarse particles and the filter medium is not blinded. Overflocculated pulps, although filtering well, may yield wet cakes. Average Particle Size and Cake Moisture A method for predetermining the surface moisture content of coal filter cakes was published in 1949; but this method could not be applied to coals deficient in —200 mesh material or to fine mineral concentrates. Test data obtained for geared-weight types of vibrating screens4 and for centrifuges5 used to de-water coal provided definite correlations between the average particle size of a dewatered cake and the surface moisture content of the cake. It was thought that this same method of correlation should be applicable to filters, whether dewatering fine coal or fine mineral concentrates. To develop a correlation or correlations between average size of cake and cake moisture, the author collected data for filtration operations from as many sources as possible. In a considerable number of instances the information was provided by plant preparation engineers,"-" a few of the tests were on a laboratory scale: and the remainder of the data was obtained from published articles.10-17 Table I contains size-consist and miscellaneous data for coal filter cakes, and Table II contains the same data for mineral concentrate filter cakes. Fig. 1 shows the relationships existing between the average particle size of the cake and cake moisture (surface moisture for coal and total moisture for minerals) when dewatering fine solids by a variety of makes and types of filters. Average particle size is calculated by averaging the linear openings of the various pairs of screens used in the screening test, weighted in accordance with the percentages of material in the various fractions.

Jan 1, 1952

By Frederick M. Becket, Russell Franks

In a recent article,l which described the softening effect of columbium in plain high-chromium steels, the authors stated that their investigations had shown columbium to be also a particularly valuable inhibitor of intergranular corrosion in steels of the 18 per cent chromium, 8 per cent nickel type. It is the purpose of the present paper to record some of the results obtained through the introduction of columbium to the austenitic chromium-nickel steels. The damaging effects of this type of corrosion have become so widely known as to restrict considerably the applications of the steels under consideration, and therefore there is little question of the importance of the goal to be attained. Numerous contributions concerning the susceptibility of the austenitic chromium-nickel steels to intergranular corrosion have appeared during the past few years, and among others who have dealt constructively with the subject are such well-known authors as Strauss and Houdremont of Germany, Hatfield of England, and Bain in the United States. Different theories have been propounded as to the cause of intergranular corrosion, and various remedial measures have been proposed, the majority of which involve the use of addition agents. Titanium is the addition agent at present most generally employed, as suggested by Houdremont and modified as described by Bain, Aborn and Rutherford. Little has been published on the effects of holding these steels for long periods at the relatively lower temperatures in the presence of corroding media, and the effects have mot been fully realized by producer and consumer.

Jan 1, 1934

By J. L. Snoek

[ ] DISCUSSION J. L, SNOEK*-Stress-induced preferential diffusion in cubic body centered metals in the annealed state provides us with a powerful tool for determining the mobility of interstitially solved atoms as well as their location in the lattice and the exact nature of the distortion brought about in the lattice by their presence. Calculations given by D. Polder31 show that the distortion of the lattice, besides being proportional to the applied stress P, is also proportional to [VC, RT + xVCo] where T, V and Co are the temperature, molar volume of the solvent and molar concentration of the solute respectively and x is a constant describing the mutual interaction energy of the dissolved particles. This calculation obviously is no longer valid if x is negative and the abso¬lute value of xVCo surpasses that of RT. The lattice may then be expected to become tetragonal spontaneously. Such a spontaneous tetragonality seems to have been observed by W. Klemm and L, Grimm for the case of oxygen solved in vanadium.32 Measurements of the internal friction in cold worked iron containing carbon or nitrogen should provide us with information on the mobility as well as the preferential location of these particles in the iron lattice in the cold worked state. The work by T'ing-Sui Kê is a valuable contribution to this problem, The data obtained by T'ing Sui Kê and myself on cold worked samples of iron seem to indicate that carbon and nitrogen in these samples are found either in the normal (1/2 , 0, 0) interstices or in a new preferential position created by the cold working. The latter positions in my opinion can hardly by anything else but the edges of the dislocations. The observed larger distances of diffusion might be explained by assuming that the carbon atoms when freed from a certain dislocation by thermal agitation must diffuse over several atom distances before being caught in another dislocation. The theory however needs working out and no doubt will be much more complicated than the one valid for the annealed state. T'ING-SUI KÊ (author's reply)-It is highly encouraging to read the written discussion given by Dr, Snoek who initiated the theory of stress-induced preferential diffusion in cubic body centered metals in the annealed state, Since the presentation of this paper, the author has done more experimental work on this subject which seems to be able to settle several of the points raised by Dr. Snoek. It has been found that such stress-induced preferential diffusion occurs also in the solid solutions of carbon,33 oxygen,34 and nitrogen35 in tantalum which has a body centered cubic structure. Analysis of the shape of the observed internal friction. peaks indicates that the inter-

Jan 1, 1948

By B. H. Mot

Underground water has been one of the greatest problems in sinking mine shafts, sealing existing shafts, and driving headings under streams. In the preparation of a proposed shaft or existing shafts for elimination of water leakage, advances have been brought about through the use of a controlled grouting method. The modern method to divert water from proposed shaft sites is known to us as pre-grouting, and from existing shafts, as controlled pressure grouting. This method involves the solidification of the surface and rock by the injection of a liquid mixture of

Jan 1, 1949

By H. M. Howe

(Read at. the Lake George Meeting, October, 1878.) MANY direct processes have been proposed for the treatment of oxidized ores of copper by reducing the copper oxide to the metallic state, and by separating it from its impurities by a subsequent fusion. The radical objection common to all the methods which have come to my notice, except those in which sulphur plays the prominent part, is that the very deoxidizing agent which effects the reduction of the copper oxide, inevitably reduces at the same time a very considerable part, if not the whole, of the iron which almost invariably accompanies copper in its ores. The result is that, when the ore is subsequently fused, a very great quantity of the already reduced iron separates from the slag along with the copper, alloying with it, and necessitating costly subsequent operations for its separation. Thus, at Perm, in the Urals,* the product of the fusion of ferruginous copper oxides is a mixture of one hundred and fifty-five parts of highly cupriferous pig iron with two hundred and five parts of very impure and ferruginous black copper, containing some 10 per cent. of carbon and iron, though free from sulphur, and of course very difficult to refine. If, in order to avoid this reduction of iron to the metallic state, the reducing action be made feebler, it inevitably results that a considerable part of the copper as well escapes deoxidation ; and, consequently, the slags are so rich that it becomes necessary to treat them subsequently in order to recover the copper which they contain. Thus, in treating native copper, at Lake Superior, where the reducing action is purposely made feeble in order to prevent the deoxidation of the iron, the slags from the first fusion of the ore carry so much copper as to render it imperative to treat them again, which is done in a cupola. And yet, in spite of so far weakening the reducing action as to cause a notable slagging of the copper, a very considerable reduction of iron actually takes place. These are the two dangers which threaten the smelter of oxidized copper ores. If he wishes to avoid slagging his copper, he must have so strong a deoxidizing action as to reduce a great deal of his * Rivot, Prineipes Généraux du Traitement des Minerais Métalliques, i, p. 79.

Jan 1, 1879

By B. Ehgartner, M. Karmis, C. Haycocks

INTRODUCTION Interaction effects between mining operations developed on different levels of contiguously placed bedded deposits are a major problem in many parts of the United States. Efficient design criteria, derived from careful analysis of field studies as well as theoretical and model analysis, have shown that many problems that may result from seam interaction can be avoided, minimized, or on occasion used with beneficial results. Selection of seam mining sequence is rarely based only on ground control considerations, but rather on factors such as seam ownership, characteristics and accessibility. Therefore all possible mining sequences and methods must be considered in the development of multi-seam design criteria. Increased utilization of the longwall method of mining creates special problems in multi-seam mining due to the inevitability of caving and, therefore, subsidence. Considerable valuable experience has been gained in this direction from British mining operations where interaction problems are extremely common and the longwall method is the primary method used. However, limitations persist in the application of much of this information to U.S. conditions due to variation in layouts between advancing and retreating longwall systems and the inherent difference in the geologic environment. Considerable field data is available for U.S. room and pillar operations, and where successful pillaring operations have been carried out close parallels may be drawn with ground control mechanisms in longwall operations. VARIABLES AFFECTING INTERACTION Analysis of ground control multi-seam problems shows that factors contributing to interaction may be classified into variables that are fixed by the geo- logic environment and those that depend on engineering design. These may be described as follows (Haycocks et al, 1982): Fixed: (i) Depth*, (ii) Innerburden thickness*, (iii) Innerburden physical characteristics*, (iv) Stress field, (v) Seam thickness, (vi) Coal characteristics, (vii) Completed mining operations either above or below the seam to ve mined, and (viii) Age of workings. Mining: (i) Height, (ii) Dimensions and geometry*, (iii) Method*, and (iv) Spatial location of entries* *These variables are regarded as being critical effects. Few attempts have been made to quantify the variables controlling interaction. Dunham's (1978) linear regression analysis, combined with the National Coal Board's MRDE Roadway Monogram, is probably the most noteworthy. This study involved eighteen multi- seam longwall mines in the United Kingdom. The following variables were taken into account: seam depth, pillar width, opening shape, floor and roof conditions, rate of face advance, vertical seam interval, and age and geometry of overlying workings. A multi-linear regression analysis of these variables fitted by appropriate field values developed a prediction equation for lower seam stability. Although the study included many variables, it neglected the nature or geology of the innerburden. The prediction equation was found unreliable, but it did show the significance of geometry as a factor controlling lower seam stability. MINING SEQUENCES Irrespective of the type of mining method selected only four possible mining sequences are possible for two seams. Finlay and Winstanley wrote in 1934. .. "Experience has shown that whether the upper or lower seam was worked first, the subsequent working of the other seam in the same area seriously affected the roads in the seam first worked." Those effects depended upon the four basic mining sequences: 1) The upper seam is mined out prior to mining the underlying seam; i.e., the seams are mined sequentially downward and mining of the underlying seam is not commenced until operations above are completed and have ceased.

Jan 1, 1982

By G. Ansell, J. Weertman

G. Ansell and J. Weertman (Rensselaer Polytechnic Institute and Northwestern University, respectively) —The great increase in creep strength that you found in your indium-glass composites is quite striking. You ruled out a decrease in the dislocation source density as an explanation of the reduced creep rates. Could you tell in greater detail why you feel this is an inadequate explanation of the phenomenon. It appears to us that it is a reasonable one. Consider the spacing between the glass spheres in your composites. It is of the order of 10-3 cm. The spacing between dislocations in a (single-phase) annealed metal with a dislocation density of the order of 106 to 107 cm per cm3 also is of the order of 10-3 cm. Therefore it is not reasonable to expect that the arrangement of the dislocation lines is the same in the composite material as it is in pure indium. If the dislocation arrangements are different the density of the dislocation sources likewise will be different. Another way of saying the same thing is the following. The presence of the glass spheres reduces one of the dimensions of the metal phase to 10-3 cm. Thus the metal phase, in effect, is equivalent to a metal whisker or a thin metal film. These are strong because they have so few dislocation sources within them. T. D. Gulden and J. C. Shyne (authors' reply)—It is to be expected that the arrangement of dislocations in the indium-glass composites would be quite different than that observed in annealed pure metals. The dislocations probably exist primarily as segments connecting the dispersed particles. These segments and discontinuities at the very large area of particle-metal interface could act as dislocation sources. For this reason it was considered unlikely that the very high observed creep strengths were due to a low density of dislocation sources. A more likely explanation is that the distance a dislocation can glide is limited by the interparticle spacing. The particles averaged about twenty in diam and were less than 10 µ apart in the 40 pet composite. It seems reasonable to assume that a dislocation loop in a volume of metal surrounded by these relatively large particles would not bow out around them but would be restricted to the region between particles. A general expression for creep rate is given by the product of the dislocation source density, the average rate at which loops are generated from a source, and the average area swept out by a loop times the Burgers vector magnitude. Assuming that the area swept out is limited by the interparticle spacing and the rate of generation of loops is controlled by the rate of climb of loops over second-phase particles, as suggested by Ansel and Weert-men,9 a calculation of the dislocation source density may be made from the experimentally observed creep rates. The result comes out 10" to 10" per cm3 which seems reasonable in view of the assumptions involved. Thus it is concluded that the anomalously low creep rates that were observed were due not to a low dislocation source density but rather to a limitation on the area swept out by each dislocation loop.

Jan 1, 1964

By D. R. Miller

The use of fully grouted cables for ground reinforcement in underground mining is becoming widespread. Reinforcement design for this application has tended to be empirical although some two- dimensional design techniques have been developed. This paper describes a technique based on a model of the behaviour of cables placed across planes moving in shear. The model is three- dimensional and includes a simple model of the 'dowel' effect which arises from the bending of the cables. The model determines the shear resistance developed at a particular shear displacement assuming joint friction and cable parameters. Using data for twin 15.2mm dim. steel strand cables, and a concept of reinforcement efficiency, the application of the model to design wall support in open stopes is demonstrated. The examples consider the cases where major planar structures are known in location and orientation and where, as is more common is open stope development, mapping has indicated that a distribution of potential shear failure structures may be present. The actual location and orientation of potential shear planes is not known. These two cases highlight the underdesign of reinforcement that may arise if the distribution of orientation of potential shear planes is not considered.

Jan 1, 1984

By Henry M. Howe

.... So, beyond and above the immediate and tangible ends of membership, ever-present and evident, selfish and generous alike; beyond and yet at the root of that genuine affection for our association which is so strong in many of us, there lies earnest sympathy with the ultimate and essential purpose of its being—that to which as a nucleus all other purposes are but contributory—which is, to

Jan 1, 1895

By J. B. Newkirk, A. H. Geisler

Certain of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some perrnanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems oA&apos;er for study over the usual in which an intermetallic compound is formed are many: 1. Since the precipitate has the same crystal strutture as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be ex. petted to have the same orientation. 3, Small &,registry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from 0 to 100 pet* thus permitting wide freedom for the study of the effect of cornposition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1&apos;2 The two have the same <Jo parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for CU-Ni-CO alloys because of the similarity in constitution but this had not been demonstrated. The Present investigation was conducted on a CU-Ni-CO alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established, however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system Was chosen for a comprehensive investiga-

Jan 1, 1949

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.&apos;-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By Burt C. Mariacher

To note that environmental considerations had a major im¬pact on the minerals processing industry in 1971 would be something less than a profound observation. The degree of its importance was demonstrated by MBD when it established the Environmental Committee as a new unit committee within the Division to achieve greater participation in exchange of information relating to the technologies and problems involved. It is appropriate and necessary to devote special attention to this timely aspect of minerals processing, as its influence penetrates the research, engineering and operations of almost all unit technologies that comprise minerals processing. The pollution abatement aspect of this industry has been such a dominant factor in recent years there is reason to wonder whether progress in unrelated technologies has been curtailed. Perhaps so, to some degree, but unit committee reviews presented in this article suggest rather that it would appear to have served as a catalyst for accelerated progress in development of new methods and improvement in more conventional ones. Present concepts regarding primary metal or mineral recovery and by-product potential may change considerably as a result of improved technology in waste product treatment.

Jan 2, 1972

By Geo. H. Ashley

THE present critical state of the supply, distribution, and utilization. of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibituminous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bitumi¬nous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coals by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by, which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service.

Jan 8, 1919

By G. St. J. Perrot, S. P. Kinney

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By S. P. Kinney, G. St. J. Perrot

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By Blamey Stevens

My previous paper is entitled, The Laws of Igneous Ernanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical couditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming from those parts of the intrusion which have solidified below the lower level.

Jan 1, 1913

By Alexander Gow

THE object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the "bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a compre-hensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific varia-bles, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this "new philosophy" consists of using power as an index of the mill operation, and investigating grind-ing from the standpoint of set and induced variables, with emphasis on the latter.

Jan 1, 1934

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959