Search Documents

By J. Chipman, H. Towers, M. Paris

A simple radioactive tracer technique is used to measure the diffusion coefficient of calcium ion in molten slags. In a slag of 40 pct Ca0-40 pct Si0,-20 pct Al203, Dc " at 1450°C is 1.3x10-6 cm' sec-'. THE application of the principles of thermodynamics to steel and iron making problems has proved so fruitful that the kinetic approach has tended to be neglected. It seems probable that in some reactions the rate-determining step is the dif-fusivity of the reactants or of the products. But knowledge of the diffusion coefficients of the constituents of liquid slag and metal is singularly lacking. The present work was undertaken as a first step toward supplying such data for slags. Furthermore, any additional information on the physical properties of liquid slags might be expected to help in elucidating their structure. It is essentially a preliminary investigation, the course of which was determined more by the necessity of establishing a method than by the immediate intrinsic interest of the results. For example, the selection of calcium ion to be studied was dictated by the suitability of the isotope Ca45 in that it is a simple emitter with a long half-life. Of the other ions commonly encountered in slags, the isotopes of iron and manganese have relatively complex radiations as well as the normal disadvantage of requiring control of the oxygen potential of the atmosphere; Mg27 and Al29 have half-lives measured only in minutes; Si3' has a simple decay process but its half-life of 2.8 hr is too short for preliminary studies; the only useful oxygen isotope is the stable O18; and there remain only sulphur and phosphorus both of which have suitable isotopes but were rejected as being of less fundamental interest than calcium. Similarly a lime-alumina- silica slag was used in preference to calcium silicate primarily because of its low melting point and its capacity to form a glass on fairly rapid cooling. Literature Review Very few studies of diffusion in liquid silicate systems have been reported. In order to determine the origin of diopside inclusions in felspathic rocks, Bowen1 investigated the diffusion between diopside and various mixtures of albite and anorthite. Platinum crucibles were used with diopside, the heavier of the two liquids, forming the lower half of the cell and diffusion taking place against gravity. Change in concentration along the diffusion path was found by measuring the refractive index of the quenched glass. Nearly thirty years later McCallum and Barrett2 used essentially the same method to determine the diffusion coefficient of lime in lime-alumina-silica slags. In this case the interest was to find the rate-determining step in the process of slag attack on refractory materials. In an investigation of the kinetics of the sulphur reaction, Derge, Philbrook, and Goldman8 determined the diffusion coefficient of sulphur in a typical blast furnace slag by the simple procedure of melting a slag containing 2 pct S over an identical slag sulphur-free. They make no claim to a high degree of accuracy but suggest that D, is of the order of 10-6 cm2 sec-l. Other high temperature liquid diffusion studies have been concerned with metals. Holbrook, Furnas, and Joseph4 determined the diffusion coefficients of silicon, phosphorus, sulphur, manganese, and carbon in liquid iron by immersing a small carbon crucible containing pure iron-carbon alloy in a large vessel containing iron with a high concentration of the particular element. Their results were confirmed by Paschke and Hauttmann5 using a similar method. Diffusion coefficients in silicates in the glassy state have been studied by Johnson, Bristow, and Blau6 Both Na24 and Ca45 were used as tracers but only the

Jan 1, 1954

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By V. S. Swaminathan

This year, Great Britain is looking back over a century to August 14, 1850, the day when the first "Act for the Inspection of Coal Mines" was passed in that country, an act which signaled the end of over two hundred years of hitherto uncontrolled and dangerous mining practices. It was back in the time of Queen Elizabeth that . thousands of pounds were invested in mining, particularly coal mining in England and Scot- land. By 1640 there were collieries producing 10,000 to 25,000 tons of coal per year. In the seventeenth century the Tyne district coal industry was organized into powerful partnerships, and coal took an even larger part in industry, as a source of power and as fuel for the iron industry. In the early 19th century a "phenomenal, almost devastating expansion" characterized Britain's coal industry, and it was sparked by a 111 pct in- crease in the population of England and Wales in the first half of the century. Coal production for those 50 years increased 470 pct and pig iron production was up 946 pct for the period 1801-51.

Jan 1, 1950

By Charles Mitke

EXCLUDING top-slicing, and sublevel caving, large production caving methods may be divided into two general classes, the branch raise, or undercut caving method, and the combined shrinkage and caving method, each of which has a number of variations, the result of continual efforts towards obtaining lower costs and better extraction, by the introduction and substitution of minor improvements and modifications. EARLY CAVING METHODS Present caving methods are the cumulative result of developments covering a period of many years, with the most rapid growth during the past 15 years. They originated, presumably, from early English stoping methods, and, as far as is generally known, were first introduced in the Michigan iron district. They have had their greatest expansion and application in the large low-grade porphyry coppers. In their present form, they are probably a development and combination of sublevel caving and shrinkage (back-stoping on ore) with gravity handling of broken material. Sublevel caving, as practiced in the Michigan district today, is a combination of drift, or crosscut, mining, with top-slicing, and caving, supplemented by later refinements in the shape of mechanized handling of broken ore. A height of anywhere from 16 to 20 ft. is generally taken, and the ore is drilled and blasted along the drift or crosscut for half this height (say 8 to 10 ft.), after which the upper 8 to 10 ft. caves and breaks of its own weight, with comparatively little assistance from drilling. This

Jan 1, 1928

By Charles A. Mitke

Excluding top-slicing and sublevel caving, large production caving methods may be divided into two general classes, the branch raise, or undercut caving method, and the combined shrinkage and caving method, each of which has a number of variations, the result of continual efforts towards obtaining lower costs and better extraction, by the introduction and substitution of minor improvements and modifications. Early Caving Methods Present caving methods are the cumulative result of developments covering a period of many years, with the most rapid growth during the past 15 years. They originated, presumably, from early English stoping methods, and, as far as is generally known, were first introduced in the Michigan iron district. They have had their greatest expansion and application in the large low-grade porphyry coppers. In their present form, they are probably a development and combination of sublevel caving and shrinkage (back stoping on ore) with gravity handling of broken material. Sublevel caving, as practiced in the Michigan district today, is a combination of drift, or crosscut, mining, with top-slicing, and caving, supplemented by later refinements in the shape of mechanized handling of broken ore. A height of anywhere from 16 to 20 ft. is generally taken, and the ore is drilled and blasted along the drift or crosscut for half this height (say 8 to 10 ft.), after which the upper 8 to 10 ft. caves and breaks of its own weight, with comparatively little assistance from drilling. This

Jan 1, 1928

By Jeremias K. Chitunda

Significant cost savings and improved ground stability are two initial indications from the current wet process shotcrete ground support program at the Lakeshore mine. The area of shotcrete for ground stability is not strange to the Lakeshore operation. Since the beginning of the project, various shotcrete techniques have constantly been experimented with, incorporating all the latest technological developments. Over the years, the use of shotcrete has been employed as a primary, temporary, or permanent support, singly or in combination with rockbolts and steel sets. The extent of shotcrete usage compared with steel sets and rockbolts has varied from time to time as dictated by the overall state of the art. In 1972, for example, the ratio of the linear drift footage supported with shotcrete to that supported with steel sets averaged 1.0. In 1973, that ratio was about 3.0. Overall, for the Lakeshore mine, there are about 8000 drift ft of shotcrete, 8000 drift ft of steel sets and timber, 750 drift ft of formed concrete, 21,000 drift ft of rockbolts, and 3700 drift ft of combined type support.

Jan 12, 1974

By W. W. Mullins

The development, by the mechanism of volume diffusion, of a grain boundary groove on an interface separating a solid phase and a saturated fluid phase is calculated under the following assumptions: 1) isotropy of the interfacial free energy 's, 2) applicability of the Gibbs-Thompson formula relating curvature and chemical potential, 3) a nearly planar groove surface. The groove profile is found to have a .fixed shape and linear dimensions that are proportional to (time)1/3. The constant of proportionality is evaluated and involves ?s in such a way that the latter my be evaluated from grooving kinetics. A grain boundary that intersects an interphase interface will tend to produce a groove along the line of intersection (Fig. 1). The ultimate motivation for the formation of the groove is the reduction in interfacial free energ that occurs as the grain boundary contracts. Smith has discussed the way in which the free energy of the interfaces determines their dihedral angles at the groove root and has given a detailed analysis of the effect of the dihedral angles upon the nature the microstructures developed in polyphase alloys. Herring2 has extended the considerations to the case in which the free energy of an interface depends on its orientation and has thus added torque terms to the condition for interface equilibrium. Although the grain boundary and the interphase interface may quickly achieve the proper equilibrium angles where they intersect, as determined by the balance of equivalent tensions and torques,"2 the groove will generally continue to grow (though with decreasing speed). Thermodynamically, this continued growth reflects the fact that the lowest free energy cannot be achieved until the entire grain boundary has been eliminated; mechanistically, the growth occurs in response to inhomogeneities of chemical potential that are caused by the constraint of fixed dihedral angles at the groove root. The latter point is illustrated in Fig. 1, which shows that atoms* near the groove are on the convex side of a cylindrically curved surface and therefore have a higher chemical potential than atoms on the flat interface beyond. Thus atoms tend to leave the curved groove shoulders and force the groove to deepen. When both phases are solid additional chemical potential gradient may arise from whatever strain fields are necessary to insure continuity of material across the interface. In the discussion that follows, this complication due to strain will not occur since we always assume one phase to be a fluid and the other a solid. The transport processes that may operate to permit growth of the groove are surface (interface)* diffusion, volume diffusion in the phase on either side of the interface, and evaporation-condensation when one phase is gaseous. (Also a melting-freezing process is responsible for groove enlargement on a solid-melt interface as discussed in Sec. VI). The theory of grain boundary grooving has been discussed in detail for the processes of surface diffusion and of one type of evaporation-condensation.3'4 The theoretical predictions for the mechanism of surface diffusion have been confirmed in an experimental study of grooving kinetics in copper.5 In this paper, the theory of groove development by volume diffusion will be presented. Volume diffusion can occur either by atomic migration in the solid S or by diffusion of S atoms in the fluid phase, or solvent, adjacent to the groove surface. As discussed in Sec. V, volume diffusion in the solid should be less important than surface diffusion in forming a groove. Apart from verifying this statement then, the main interest of the present analysis centers on diffusion in an external solvent. The solvent may be either a liquid (e.g., water, or-

Jan 1, 1961

By R. Raring, W. J. Harris, J. A. Rinebolt

The effects of additions of alloying elements on the true-stress, true-strain characteristics of 0.30 pct C, 1.00 pct Mn, 0.30 pct Si pearlitic steel were studied. The alloying elements investigated were C, Mn, Si, P, The alloys are compared on the basis of fracture stress, fracture strain, energy to fracture, rate of strain hardening, strain hardening exponent, height of the flow curve, and lower yield point. IN the past, nearly all studies of the effects of alloying elements on the tensile properties of metals have compared the conventional engineering parameters, namely, tensile strength, yield strength, elongation, and reduction of area. Recently, however, the true-stress, true-strain method of recording results from the tension test has been used; Lacy and Gensamer,' Hollomon," and French and Hibbard- are used this method to study the effects of composition on strength and ductility of metals. In this paper, the effects of certain alloying elements on true-stress, true-strain curves of steels with nearly constant grain size and pearlite spacing are presented. The notation employed in this paper is given in Table I. Since the definitions of stress and strain and the analytical geometry of the stress-strain curve have been explained previously, for example by Gensamer,' they will not be reviewed here. However, the method used for the determination of energy to fracture, E,, requires mention. These energy values were calculated on the assumption that the flow curve followed the idealized equation:' corresponds to the specific energy absorption to that strain value. There is justification for preferring the use of eq 1 for the determination of the energy to a particular strain rather than the area under the experimental stress-strain curve, since Gensamer showed that the use of the Bridgman correctione for stress at the neck of a tensile specimen brought the corrected experimental curve nearer to the idealized power-law curve than to the uncorrected experimental curve. However, it should be noted that the difference between the areas under the idealized curve and the experimental curve is not great for strain of less than 1.0, as can be seen from Fig. 1. In this figure, the true-stress, true-strain curve for a 0.01 pct C, 1.00 pct Mn steel is plotted through the experimental data points. From the value of a,, from this curve and the value of n as determined by the Inm-

Jan 1, 1952

By B. D. Thomas

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water. The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion

Jan 1, 1943

By Wilford S. Wright

FOR the past four years the management of the Black Hawk Consolidated Mines plant at Mogollon has conscientiously kept accurate records pertaining to cost of operation and the performance of certain equipment. These records have been valuable in coordinating the work in the mine, mill and power plant. Also, as to quantity and kind of equipment and supplies most suitable from the standpoint of economy and dependable operation, they have served as a guide. Through comparison with records at other mines, where the same things are being done in a different way, they have pointed out mistakes to be avoided. No outstanding accomplishments, either in costs or performances, are revealed; in fact, some of the results are perhaps quite inferior to those obtained at similar plants, but it is with the thought that more records should be published for the benefit of the mining profession that the author presents these data. To other operators and to mining engineers who are called upon to make estimates for prospective operations, the information herein should be helpful. GENERAL CONDITIONS Mogollon is in the southern part of Catron County, southwestern New Mexico. It lies near the western border of the Mogollon Range, 14 miles east of the Arizona line. Silver City, 80 miles to the southeast, is the nearest railroad point. The connecting road, over which supplies are hauled into camp by trucks, is an improved highway for about 50 miles; the remainder consists of graveled roads and unimproved steep mountain grades. One general supply truck and one tank truck make daily round trips. Hauling of supplies to the mine has cost at the rate of $0.08 per ton-mile; or, on the basis of ore production, $0.30 per ton mined. Lumber, hauled in from local mills, has cost an average of $30.00 per 1000 board feet, $8.50 of which has been for hauling. The annual consumption averages 108,000 board feet. Lime, hauled from a plant in Arizona, is about the only other item not brought out from Silver City. Fuel oil for the generation of power is the item of greatest hauling expense, the f.o.b. Mogollon cost of approximately $0.06 per gal. being nearly twice the f.o.b. refinery price. Water for power plant, mill and camp use flows to camp storage tanks through a 4-in. pipe line from a spring and intake 3 miles up Silver Creek Canyon. A few times, particularly in the month of June, mill operations have been suspended for two or three days because of water shortage. MINING CONDITIONS During the years 1938, 1939, 1940 and 1941, the mine produced 230,059 dry tons

Jan 1, 1943

By L. W. Kempf

THE thermal conductivity of aluminum alloys is of considerable indus-trial importance. This is particularly true in such applications as inter-nal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determina-tion, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate-values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz1 as applying to metallic elements and later shown by Lorenz to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance.

Jan 1, 1937

By G. A. Guess

THIS investigation was started with the idea of determining whether copper-nickel mattes might not have a lower flowing temperature than copper mattes, and thus perhaps aid in accounting for the difficulty so far experienced in attempts at pyritically smelting copper-nickel ores. We have used the term flowing temperature to avoid confusion with the usual melting temperature. The idea at first was that there might be a greater viscosity range in the one matte than in the other. In the early experiments it was in our minds to determine the relative fluidity of the mattes at a given temperature. Looking to this end we tried pouring equal quantities of matte at the same temperature down an inclined graphite slab, and comparing the distances traveled. Results from such experiments were not satisfactory. We next tried pouring equal quantities at the same temperature through a drilled hole in an Acheson graphite crucible, timing the flow with a stop watch, the whole operation being carried out in the muffle. The flowing temperatures of the mattes tried in this way appeared to be about the same, and there was no marked difference in their fluidity when well fused. Oxidation gave some trouble. These experiments finally led to the adoption of the following apparatus which we thought at the time was wholly original with us, but which we have since found was described by W. McA. Johnson.' The tray used was a slab of graphite 8 in. long, 2 in. wide and ¼ in. thick. It had six holes, into each of which sat a cup of Acheson graphite. Centrally in the bottom of each cup was a vertically drilled hole 3/16 in. in diameter and ½ in. long. The mattes to be tested were put into the cups, in a solid piece. The cups were covered with inverted Battersea "A" cups. The tray was put into the muffle of a gas-fired furnace. Supports on .each end held the tray about 2 in. from the floor of the muffle. Udder

Jan 6, 1916

By T. Leffers, A. Grum-Jensen

The development of texture in copper and brass (15 pct Zn by weight) rolled at room temperature and in copper rolled at -196°C has been followed by determination of pole figures for various degrees of reduction. The concurrent development in microstructure has been investigated by transmission electron microscopy. For low deformations, the texture in brass, and in copper rolled at -196°C, is the same as the texture in copper rolled at room temperature. The difference in texture does not show until 50 pct reduction. At the same reduction at which the difference in texture appears, mechanical twinning starts in brass and low-temperature rolled copper. Nevertheless, Wassermann's twinning theory is found to be incompatible with the present resulls. All fcc metals and alloys develop, by heavy rolling, one or the other of two types of texture, classified for convenience as copper type and brass type, or possibly a '(mixed" texture representing an intermediate stage between the two types. The pure fcc metals, except silver, develop copper-type texture by rolling at room temperature. Silver and many alloys, including brass with more than 10 pct Zn, develop brass-type texture.' By rolling at low temperatures a transition in texture from copper type to brass type has been observed for copper of commercial purity.2'3 It is generally accepted that there is a correlation between the type of texture developed and the stacking fault energy. Metals and alloys having fcc structure develop brass-type texture when rolled at room temperature if the stacking fault energy is low, whereas those with higher stacking fault energies have copper-type texture.2 Thus, the difference in stacking fault energy must cause a difference in deformation mechanism responsible for the difference in texture. Of the numerous theories advanced concerning the nature of this difference in deformation mechanism, four seem to be of current interest. Smallman and Greeen,2 Dillamore and Roberts,4 and Dillamore5 refer to the fact that cross slip more easily takes place in a material with a higher stacking fault energy and suggest that the copper-type texture is developed by deformation with extensive cross slip whereas the brass-type texture is developed by deformation without cross slip. Haessner6 has advanced the theory that the copper-tye texture is developed by a combination of normal {111} slip and slip on other planes, mainly 1100). Thus his theory, like the theory above, proposes an additional deformation mode for the formation of the copper-type texture. Contrary to this, wassermann7 and Ahlborn et al.8 believe that the copper-type texture is obtained by normal slip. In their opinion mechanical twins will change a copper texture into a brass texture. For this reason it is suggested that the brass-type texture is developed when, in addition to normal {111}(110) slip, mechanical twinning is present. None of these theories are, however, supported by direct experimental evidence. In a recent experiment Hu et al.9 have followed the development of rolling texture in copper and brass. The texture of copper and brass was found to be es-

Jan 1, 1969

By John L. Miles

John L. Miles (Arthur D. Little, 1nc.)—Pollack and orris" have reported measurements on electron tunneling through A1-A12O3-A1 sandwiches in which the oxide was formed by gaseous oxidation in a glow discharge. From these measurements they deduced the asymmetry of the barrier and, since this is small, conclude that the mechanism suggested by Mott19 for the growth of oxide in thin A12O3 films is inapplicable. In earlier papers20 Pollack and Morris report similar work for oxide films grown thermally. In this case they find a greater asymmetry and conclude that the Mott mechanism is valid. I would like to point out that both these conclusions are quite unjustified. Mott suggests that the growth of the oxide film on aluminum results from the passage of ions through the already present film of oxide under the action of an electric field. This field results from a constant voltage which is in effect a contact potential between metal on one side of the barrier and adsorbed oxygen ions on the other side of the barrier. The theory does not require that the oxide grown is nonuniform either in stoichiometry or structure. It does however specifically assume that the partial layer of ionized oxygen on the surface remains adsorbed on the surface of the growing oxide. In other words, the so-called "built-in field" remains in the oxide only as long as the ionized oxygen is present. When a counter electrode of aluminum is deposited on the oxide, it will react with the adsorbed oxygen on the surface of the oxide, thus forming a small additional amount of oxide. It is clear, then, that there is no requirement in the Mott theory of oxide growth which would necessitate tunneling currents through an Al-A1203-A1 sample to be different when the polarity is reversed. Neither does the theory eliminate the possibility that some additional mechanism could cause the tunneling barrier to be asymmetric and hence tunneling currents to be a function of polarity in such a sandwich. Thus these tunneling-currents measurements are not germane to the question of whether the Mott mechanism is the true method of growth of aluminum oxide films. In fact, it is not surprising that there should be a difference between the oxide properties at the two interfaces (with resulting asymmetry in the tunneling barrier) since the growth conditions and growth rates must have been quite different at these two positions. S. R. Pollack and C. E. Morris (authors' reply)— The point raised by Miles above is one has caused some confusion in the past. The following is an attempt to clarify this point. The built-in field which is responsible for the growth of the thermal oxide at low temperatures arises, according to Mott, because of the passage of electrons from the Fermi surface of the oxidizing metal to surface states introduced by the adsorbed oxygen. It is assumed that the energy of these surface states lies below the Fermi energy of the metal. Electrons therefore continue to flow from the metal to the surface until the built-in electric field raises the potential energy of the surface states to the value of the Fermi energy in the metal, at which time equilibrium is obtained between the surface states and the metal. That is in equilibrium as many excess electrons pass from the metal to the surface per unit time as vice versa. The surface of the oxide prior to deposition of a metallic counterelectrode can then be pictured as follows. The Fermi energy lies in the energy gap of the oxide and is essentially pinned at the energy of the oxygen surface states. The vacuum work function of the oxide is then given by the sum of the electron affinity of the oxide (i.e., the difference in energy between the vacuum and the conduction-band minimum) plus the energy difference between the conduction-band minimum and the Fermi energy. The deposition of a metal onto the surface of the oxide can result in a transfer of electrons across the extremely thin oxide only if there is a contact potential difference between the deposited metal and the parent metal or oxide. That is if the vacuum work function of the deposited metal differs from that of the parent metal, then charge can be redistributed across the oxide in order to equilibriate the Fermi energy across the structure. (It should be

Jan 1, 1965

By R. F. Evans, J. M. Avery

MUCH has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of -magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore 'of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this operation is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft. apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. PRODUCTION OF MAGNESIA FROM DOLOMITE In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime (CaO) value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or

Jan 1, 1945

By D. F. Stoneburner

The thermoelectric power and electrical conductivity of a series of liquid alloys of thallium were determined in order to study the relation of chemical bonding to semiconduction in liquids. The results indicate metallic behavior for the alloys of thallium with arsenic, antimony, and bismuth, while the sulfides, selenides, and tellurides indicate semiconduction. The results are compared with the Properties of the same alloys in the solid state. This work supports the observation that long-range order is not a necessary requirement for semiconduction. PREVIOUS work1,5 has shown that some sulfides and oxides behave as semiconductors in the liquid state. Although the band theory has been of great help in understanding the properties of solid semiconductors, its quantitative application to liquids is difficult. The very existence of liquid electronic semiconductors shows that ascribing the discrete structure of the energy spectrum to strict lattice periodicity, or long-range order, is not always satisfactory. Rather, the short-range order determines the structure of energy levels and the width of the forbidden gap and, consequently, the concentration of free holes and electrons. This is borne out by the analysis of data accumulated by Regel and coworkers.6 The similarity of electronic structure of liquid and solid phases of certain liquid metals was pointed out by Knight et a1.,7 who examined nuclear resonance in solid and liquid Li, Na, Rb, Cs, Mg, Al, Ga, Sn, and Bi. They found noticeable changes in the electronic structure upon melting only in the cases of bismuth and gallium. They concluded that "a liquid metal possesses a band structure which is very like that of the solid, provided the short-range structure is not altered during melting." In semiconductors in which the near-neighbor arrangement remains the same on fusion, the material would be expected to retain its semiconducting properties. The quantum theory of semiconductors, with its band structure of energy levels, is linked exclusively to long-range order. Furthermore, it has limited usefulness in predicting new semiconductors. Many sulfide8-12 have made comparisons of properties on the basis of crystal structure or the position in the periodic table, both methods involving the same factors as chemical bonding. Mooser and Pearson8"10 have pointed out that crystal structure depends on chemical bonding, and that this bonding is a property of the atoms themselves. As the periodic arrangement of the atoms offers an easy comparison of such factors as atomic weight and number of valence electrons it provides clues to expected similarities of bonding for various elements or groups of elements. This approach has led Mooser and Pearson to formulate their valence-bond theory of semiconduction, in which they define a semiconducting bond. These authors state that "semiconductivity is the result of the presence in a solid of predominantly covalent bonds. These lead, through the process of electron sharing, to completely filled s and p orbi-tals in the valence shells of all atoms of elemental semiconductors while in semiconducting compounds only one atom of any two bonded together need acquire closed s and p orbitals. The presence of empty 'metallic' orbitals in some atoms of a compound does not destroy the semiconductivity provided that these atoms are not bonded together; it may, however, give rise to pivoting resonance in

Jan 1, 1965

By S. F. Emmons

The history of the mining region of Custer county has been somewhat peculiar. Although, in the broader features of geological structure, it bears a strong resemblance to its newer and now more famous neighbor, 40 miles to the northward, the Cripple Creek mining district, it has been noted for failures rather than for successful mining ventures. Yet it has a number of mines that have proved themselves to be remarkably rich, and many others that have well-defined veins and very rich ore, though they never have been worked to any great depth. A few of the deposits seemed to the early miner so anomalous in form and manner of occurrence that they were popularly described as " contrary to all geological laws." The region has had several " booms," succeeded by more than usually violent reactions, the latter having proved more permanent than the former. It was, for a long time, the favorite resort of patent-process mongers, and the ground is now strewn with relics of various unsuccessful reduction-plants. Mismanagement, ignorance and disagreements among mine-owners seem to have been quite as responsible for the want of success in the region as the quality of the ores or the form of the deposits. In the early eighties, when the booms had not entirely died out, a division, then under my charge, of the U. S. Geological Survey, undertook an examination of the region for the purpose of making a study of its ore-deposits. The areal survey was carried to completion by Mr. Whitman Cross, but the study of the mines could never be completed for the reason that most of them were closed, for one reason or another, before we had time to visit them. From time to time, one or another of the important mines has been started up again, but it was not

Jan 1, 1897

By Ernest N. Patty

Placer gold-bearing gravels of interior Alaska and the Yukon are, for the most part, permanently frozen, and are described as permafrost. The first step in preparing these gravels for dredging is to strip by bulldozer the surface layer of tundra, brush, and scrub timber, and to expose the ebony colored surface of the frozen mud at the grass roots. This mud varies from a frozen, muddy ooze to a sandy silt and locally may contain layers of peat. The whole mass is intercalated with ice dikes and lenses. The thickness will vary from a few feet up to 100 ft, depending upon local conditions. A freshly exposed surface will thaw to a depth of 4 in. per day during the summer season. Common practice is to expose a large surface of this mud to the sun and each day's thaw is then swept off by water and carried away in suspension.

Jan 1, 1951

By R. R. Wilson

THE Cassidy Colliery operated by the Granby Consolidated Mining, Smelting & Power Co., Ltd., is situated about 9 miles in a southerly direction from the city of Nanaimo on Vancouver Island. The coal seam worked, which is called the Douglas bed, outcrops in the western part of the property, clipping easteyrl, and is opened by a slope 7 by 14 ft. in the clear, and is timbered by 12 to 14-in. framed sets of timber, 4 ft. center to center. A separate manway provides for a traveling road and at the same time forms an intake airway. The general average of the dip of the seam at Cassidy is 18°, and varies in thickness from 1 to 25 ft., averaging about 8 ft. The main slopes follow straight down the dip a distance of 4545 ft. At the bottom of the main slope two rock tunnels were driven a distance of 1500 ft. to the south, cutting through a fault, and opening up an area in the same seam which is known as No. 7 South Section. The coal is found in this section at a vertical depth of 1560 ft., and is very soft and friable. The immediate roof is a strong, sandy shale overlain by massive sandstone while the floor is a light-colored shale, hard when freshly exposed. It does not soften materially oil exposure. In the folding of the coal measures a great thrust caused a movement along the coal seam as indicated by the slickensided nature of the coal. The floor has buckled and this has rolled and squeezed the coal-so that with rare exceptions it shows no normal bedding but curved slip planes, which frequently start at right angles to the floor, curving upward and then in the direction of the dip. As such planes are slickensided it is probable that there is a coating of clay which is more or less impervious to gas.

Jan 1, 1927