Search Documents

By Robert Stefanko

Longwall mining which has a long history abroad, was used only on a limited scale in the United States until less than 20 years ago. Modern longwall mining in this country can be said to have begun in 1960 with the first installation of self-advancing props in a coal mine in southern West Virginia. In Europe, because of adverse natural conditions, longwall mining is frequently the only practical method, but, in the United States, the system has had to compete economically with highly productive room-and-pillar systems. However, because it is inherently continuous, it has greater productive potential than room-and-pillar systems, and, therefore, although only about 5% of the total U.S. underground production today is the result of the longwall system, its growth potential is great. As mining, by necessity, progresses deeper and must be done under poorer natural conditions, less opportunity will exist for the room- and-pillar system, and the longwall system will have to be used.

Jan 1, 1981

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.'. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"' * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

By Henry Hibbard

This paper aims to put into useful form the information, at hand regarding temperatures of molten steels, covering all carbon contents up to 1.5 per cent., in the hope that if the assumed ideal temperatures tabulated are incorrect the right ones may . be brought to light. THE finishing and casting temperature of steel is a subject concerning which there is so much to learn that some temerity is required to write about it. This paper is, therefore, suggestive rather than dogmatic, though the views expressed seem now to the writer to be correct; nevertheless, they may be modified by future developments or discoveries but until then may be of some utility, particularly to beginners in the making of steel. Consideration is limited to the temperatures of simple steels, also called carbon steels,, which are those in which carbon is the only element introduced for the purpose of conferring desired physical properties. Alloy steels will receive attention later. Three things largely determine what a batch of steel really will be; viz., composition, casting temperature, and rate of teeming. Each has its advocates as being the most important; but they are so interrelated that each must conform to or be right for the, other two. When one is claimed to be the most essential to have right, that, probably, was the one that it was found had to be of a certain description, within narrow limits, to suit the already adopted variations of the other two; that is, it was the last of the three to be brought into line.

Jan 12, 1924

By M. P. Dalton

THE problem at the Morning mill is to separate the galena, which contains a great percentage of the silver, from the sphalerite, making each into a commercial product. The ore as received from the nine is dumped into hopper-bottomed bins of 1200 tons capacity. These are divided into five sections, the first section being the regularly used section and the re-mainder used as a reserve bin. The ore is first passed through a 9 by 15-in. Blake jaw-crusher with an opening of 4 in. This allows a ham-mer head to pass through without damage. The crusher discharges to a conveyor that delivers the ore into a two-section punched-plate trommel screen with 1 ½ and 2-in. openings. The undersize is carried by means of conveyors to the mill bins. The oversize passes over a shaking feeder and through a spray or high-pressure water to a picking-belt, where waste and crude ore is hand-sorted. About 4 per cent of the ore by weight is picked out as waste, assaying about 0.6 per cent lead, and this is discarded over the dump. About 4 per cent of the ore by weight is removed as crude ore, assaying 10 oz. silver, 30 per cent lead, and S per cent zinc, and is shipped direct to the smelter. The remainder of the oversize from the picking-belt is con-veyed to a 4-ft. Symons cone crusher with 1-in. opening, which is interesting as a new introduction in this dis-trict. The machine consumes approximately 40 hp. and the pinion shaft travels 555 r.p.m. The horsepower is rather high, but the machine has an extraordinarily large capacity, and, due to the unique construction, there is no danger of tramp steel causing any damage, as in that case the discharge "opening" is automatically

Jan 7, 1927

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35' to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35' to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35' to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35' to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By Wilford Stork

CERTAIN influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,1 such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is really burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book3 The work of J. E. Johnson, Jr., has revolutionized

Jan 6, 1919

By R. H. Thurston

Jan 1, 1879

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

By Joseph A. Newman

THE first trial of longhole drilling of raises began in June 1949 at the Holden mine, Chelan Div., Howe Sound Co. The cost of this raise was about the same as the average cost of raising by normal methods which was sufficiently encouraging to give the method further trial. At Holden, the Noranda method of blasthole drilling is used except that percussion drills have replaced diamond drills for making blastholes in all but certain special situations. Two thirds of these holes are between 40 and 70 ft long.

Jan 10, 1951

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;' the direction and the driving force of grain boundary sliding and migration;' the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.' It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954

By H. E. Howe, A. A. Smith

E. Schumacher.*—Mr. Smith has shown us once again how variable lead alloys can be. I have studied lead alloys for a good many years and know from experience that their behavior cannot be predicted by analogy with other alloys. I have always been interested in observing how the creep resistance of lead may be improved by the addition of as little as 0.03 per cent Ca. Without the presence of calcium the grains of extruded lead pipe are fairly equiaxed and motion can take place easily at the boundaries. The calcium addition of 0.03 per cent causes the grain boundaries to become very irregular and jagged, and results in creep resistance many times greater than that of pure lead. Mr. Smith showed that in the one per cent antimony-lead alloy creep is occasionally excessive even where low stresses are involved. We have observed this phenomenon many

Jan 1, 1945

By Robert L. Wilson

Computation of reserve tonnages, stripping ratios, and grade of ore has long been a revolting aspect of the young mining engineer's job. Weeks at the desk calculator may turn into months before a single job is completed. Then many additional hours are necessary to check the calculations. During the last decade, computing machines have been widely publicized as instruments which will accomplish fantastic feats. Tales of their magical qualities have overshadowed their most basic characteristics-that of being a labor-saving device. Prior to a discussion of the electronic calculator's use on a mining problem, it may be well to point out that these machines are neither magic nor will they replace the judgment of an experienced engineer. In short, the "mighty morons," as the computors are sometimes called, are excellent labor savers but must be used correctly. They are not a substitute for thinking.

Jan 6, 1961

By Carl Zapffe

THE manganese ore reserves of Lake Superior, because of their location and nature, have recently achieved a marked degree of importance as compared with the world's manganese reserves. To appreciate fully the significance and the adequacy of this reserve, one should understand how such ores are used, where obtainable, the quantity used, possible avenues for increasing use or application, and the chemical and physical characteristics of the available ores. Only with that data at hand, is it possible to arrive at a convincing answer to the question whether the reserves of manganiferous iron ores are adequate to satisfy the annual demand of the presently known iron ores for the full life of the latter. That they should last is vital; and to ascertain whether they will last was the purpose of the present investigation, which marks the first attempt to study these Lakes Superior reserves. The Lake Superior region possesses and supplies the full assortment of iron ores needed for the conversion of ore into pig iron and steel ingots and castings. These ores are named bessemer; low-phosphorus and high-phosphorus non-bessemer, manganiferous and siliceous; and to include the term aluminiferous, would be in keeping with the most recent no men clature adopted by some dealers. About 35 or 40 years ago, perhaps less, most of the Lake Superior ore which is being used today was the material then considered either useless or too poor for immediate use; perhaps it was considered no more than a future reserve. An examination of the analyses of ores and the guarantees in the sales of those older times, convinces one that the opinions of those days must have been governed by only small differences in analyses. Some grades of ores used today in substantial amounts were used most sparingly only one or two decades ago. The relative quantities of the different ores used is ever changing; and, bit by bit, the metallurgy and the opinions are every changing and the prejudices against certain ores and practices decrease. This is unquestionably more pronounced for the manganiferous ores than for any other kind. If, when using the present data for manganiferous ores, we will only be

Jan 5, 1927

By AIME AIME

IN a recent technical paper of the Central Committee of the French Coal Mines (Note technique No. 198, by L. Lahoussay) the author points out that continuous in¬crease in depth of mine shafts makes it more and more necessary to look for appropriate means to reduce the weights and dimensions of the hoisting ropes. Increasing depth demands a larger section and weight for the cable if the useful load is not to be cut down at the same time. This naturally leads to increased cost per ton, and at the same time creates serious mechanical difficulties. The dimensions of the hoisting engine must be increased, acceleration at the start must be decreased so as to avoid periods of excessive peak power loads, and a longer time be allowed to slow down the speed of the hoist when applying brakes. The hoisting rope, upon which depend the dimensions and hence the mass of the hoisting engine, presents the greatest obstacle to the development of hoisting from greater depths. Evidently, for a given depth, the total weight of the rope can be notably reduced by utilizing a wire rope of decreasing section, approaching the theoretical logarithmic form. This is a solution frequently adopted for great depths. Of course, the weight of the rope could be easily' diminished by reducing the useful load, but it is certain that with increasing depth of mining, more effort must be made to confine the hoisting to a small number of shafts, and increase the load hoisted per trip.

Jan 1, 1933

By Thomas Egleston

The uncertainty of finding the exact equivalents fortechnical expressions in different languages has led me to think that a glossary of furnace-terms would be useful to members of the profession. I was led, some years ago, to prepare a small one, which has been found so very useful, that I have arranged one for presentation to the Institute, for four different 'types of furnaces, in the hope that it may prove of use to those who are in the habit of consulting foreign technical journals, I was further induced to make the attempt in the hope that it might tend to make the terminology less complicated than it now is, and also to make it more uniform over larger districts. The idea of referring to a drawing which expresses exactly what is meant, resulted from the necessity of presenting such subjects to students, and will, it is hoped, prove much more useful than the mere dictionary arrangement in alphabetical order. The drawing of the blast-furnace was prepared for me by Mr. J. P. Witherow, of Pitsburgh ; the drawing of the open-hearth furnace by Mr. S. T. Wellman, of Cleveland, and the reverberatory furnace by Mr. John Fritz, of Bethlehem. The bloomary-furnace is taken from my own paper* on Bloomaries, but, in order to have a complete furnace, I have introduced into the drawing of those used at Saranac the guard-plate used at Ironville. The interest which has been taken in the preparation of this paper by those gentlemen who have contributed the drawings, has been supplemented by gentlemen in Europe who have taken the trouble to read the proof. In France it has been read by Mr. Lodin, of the School of Mines, and by Mr. Chaper, of Paris, and in Germany by Dr. Wedding, of Berlin, and Mr. Luhrman, of Osnabruck. The preparation of the paper has been much more difficult than was anticipated, and its value has been very much enhanced by Dr. Raymond's kind assistance and cooperation; and to him, as well as to all the other gentlemen, Iam very much indebted. It was at first proposed to add to the paper the names of all the tools used in these various furnaces. It was found, however, that this would make such

Jan 1, 1888

The pattern of the coal industry west of the Mississippi River, so far as its history is concerned, is entirely different from that to the east of the "Father of Waters." When the Louisiana Purchase was consummated, one of Jefferson's first thoughts was to ascertain what sort of a country had been purchased, and to that end he sent Lewis and Clark to ascend the Missouri River and to reach the Pacific Ocean if possible, but above all to bring back a report showing the character of the country, its mineral and other resources, inhabitants, etc. This first expedition was supplemented by others to various parts of the vast domain for the same purpose; years later, when transportation routes were necessary to hold and develop the western country, a number of expeditions were sent to explore possible routes for railroads. The records of nearly all of these explorers, as will be shown later, contain references to coal in many localities, the possible value of which was realized but its potential value remained dormant for many years until increasing population and methods of transport made markets available. Missouri was the first state west of the Mississippi in which coal was produced and the names of a number of places show that the French were familiar with the coal deposits there. Lewis and Clark, soon after they left St. Louis, passed "a remarkable Coal Hill on the Larboard Side, called by the French Carbonere, this hill appeares to Contain great quantity of Coal."1 This hill was about seven miles below St. Charles. No other outcrops were seen by them until they had passed the present limits of the state. The Louisiana Gazette of April 9, 1805 contained an article on "The Missouri," author not stated, which said, "the short stay we have generally made among the savage nations has prevented us from making those researches, which would have supplied us with a more extensive information respecting the various mines found on the borders of the Missouri; we know with certainty only those of iron, lead and coal." In 1806 Pike passed through Missouri on his tour to Mexico. On August 17th, along the Osage River he remarked, "here the river-bank is

Jan 1, 1942

By Carl Beal

IN February, 1918, the conclusion was published by Lewis and Beal1 "that wells of equal output on the average will produce equal amounts of oil in the future, regardless of the ages of the wells." This conclusion was based upon the study of data collected principally in Oklahoma and was not known at that time to be true for other oil fields. An abundance of statistical proof was later, collected by the senior author of the present paper, which showed that the conclusion was undoubtedly well founded and that it applied to other fields as well. Accordingly, it was later restated2 as the "law of equal expectations" as follows: "If two wells under similar conditions .produce equal amounts during any given year, the amounts they will produce thereafter, on the average, will be approximately equal, regardless of their relative ages." Although only scanty data from the California oil fields were available at the time this publication was prepared, sufficient information was analyzed upon which to base the insert on Fig. 80, which showed beyond a doubt that the law held at least for a part of the Midway oil field in California. Recently the authors have collected more complete data in California, and it is the purpose of this paper to explain the method used in demonstrating the truth of the law and, in addition, to give several methods by which curves constructed in accordance with this law can be used in a practical way with ease and accuracy.

Jan 8, 1919