Search Documents

By W. F. Brace, James D. Byerlee

Although prediction of failure of rocks may be ultimately possible without knowing in detail how failure occurs, understanding of this process is certainly of fundamental interest in rock mechanics. Of the various failure mechanisms, probably brittle fracture is of greatest interest. Recent reviews have brought this subject nearly up to date (Hock,1 Price,2 and Jaeger 3) and here, we summarize certain recent developments. As our understanding of brittle fracture is derived almost solely from laboratory studies this will amount to a review of certain laboratory experiments. New studies in four areas are pertinent; these concern 1) the volume changes which accompany brittle fracture, 2) the propagation of cracks in compression, 3) certain frictional characteristics of rocks and minerals at high pressure, and 4) the law of effective stress for crystalline rocks. Our objective here is less to present an entirely consistent, complete picture of how a rock fractures than it is to emphasize gaps in our understanding and, thus, suggest areas that need further study. Progress is still painfully slow in this field and perhaps this approach will stimulate new work. OBSERVATIONS Although the behavior of large rock masses is most often the concern in rock mechanics, the number of large-scale experimental tests is still vanishingly small. Our experimental observations arc, by and large, still made on small, relatively flaw-free, rock samples. Here also we report the behavior of small samples.

Jan 1, 1967

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By Earl A. Trager

The broad picture of world petroleum production at the present time is one of an excessive supply. In any consideration of corrective measures to be applied in the future, it will be necessary to include all the producing areas of the entire world. To illustrate, United States production during 1931 was 48 million barrels1 less than 1930, whereas world production exclusive of the United States increased, owing principally to increases in Russia, Rumania and Persia. Domestic Peoduction Let us first consider the domestic production situation. Due to the fact that United States production was maintained below current demand, about 40 million barrels of oil were withdrawn from storage during 1931. Consumption increased about 1.5 per cent over 1930, which is less than the recent annual rate of increase of 8 to 11 per cent. If the machinery to prevent waste in the petroleum industry operative for more than a year will continue during the coming year and drilling is held to the 1931 level, there will be a decided improvement in the domestic situation by the close of 1932. This will be due in large measure to the drastic reduction in exploratory work and drilling which has been in effect for more than a year. Looking ahead for two or more years, probably there will be a shortage of domestic production in relation to domestic demand, unless there are discovered several large pools comparable to Oklahoma City or East Texas. Were the United States isolated, our problems in so far as petroleum production is concerned might be considered well along the road to recovery. To maintain this perspective will require the cooperation of foreign producers in the future, or protection of United Statcs markets from foreign invasion. Let us review briefly the present situation in the United States. East Texas has been the most important factor during 1931. The large initial production of individual wells and the rapid rate of drilling

Jan 1, 1932

By W. E. C. Eustis

During the last year I had occasion, on behalf of our New York copper works, to send to various chemists samples, intended to he accurate, of material which we were buying and selling, and I was astonished to find what differences were reported. After talking over the probable reasons for this with a number of chemists and metallurgists, it was suggested that it would be of real use and some scientific interest to send samples to the different chemists, and take such care in making up the samples that we could feel sure that each chemist had as nearly identical a sample as it was possible to make. After some consideration it was determined to send a mixture which should carry about 50 per cent. copper, and

Jan 1, 1883

By Otto F. Pfordte

Although the subject has no practical bearing on the metallurgy of the present day, it may not be entirely uninteresting to note how the art of silver-lead smelting has been, and in a few remote districts of Peru is still practiced by an old method, and under conditions widely different from our own. The subject will be considered under the following subdivisions,. viz.: The general conditions; construction and plan of furnaces;, fuels and ores; method of working; furnace products and slags. The mineral region of Peru varies in altitude from 10,000 to 16,000 feet above sea-level, comparatively few mines being locatedh above or below these limits. The timber-line in the valleys is at about 12,000 feet altitude on the western slope of the mountains, and even there the supply of wood is not sufficient to be utilized as fuel for furnaces. The sides of the mountains are either bare or covered with a hard bushy grass, which is most luxuriant during the latter part of the rainy season, from February to April. Agriculture on the western slope rarely reaches above 12,000 feet, while on the eastern slope its limit is at 14,000 feet; and in either case the height named is reached only in sheltered places. Transportation is slow, being carried on mainly by llamas, donkeys and mules; the former (taking 100 pounds at a load) are almost

Jan 1, 1893

By M. Gensamer

ALTHOUGH a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Wever1, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel sub-jected to plane parallel deformation1,2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straight-forward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystal-lites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of pre-ferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling proc-ess the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation

Jan 1, 1936

By Byron B. Boatright

The energy which causes oil and gas to flow from a reservoir formation into a well depends upon a differential between the formation pressure and the pressure at the well face. This differential pressure may be the result of any one of at least three forces, or a combination of them. Gas under pressure in an oil-producing formation (part of the gas may be in solution and part in contact with the oil) is the principal source of energy for producing oil in most fields. In some fields, however, hydrostatic pressure due to water in contact with the oil and/or the force of gravity may be important factors in causing oil to flow into a well. Still another force affecting oil movement is suggested by some students of the problem; the force dependent upon the phenomenon of capillarity. Hydrostatic pressure is seldom the only source of energy in an oil sand, but it is commonly an adjunct to the compressed gas in the formation. Where this condition prevails, increased production may be obtained provided the water encroachment is properly controlled. In addition to the water-drive effect, the hydrostatic head may tend to maintain pressure in the formation by progressively reducing the volume of the reservoir as withdrawals to the surface are made through the producing wells. The action of the force of gravity on the oil in a formation is of relatively small importance, from an energy standpoint, until the last stage of the productive life of a well is reached. This force is the only remaining natural source of energy in some of the eastern fields, but in most of the deep wells of the Mid-Continent and California districts the force of gravity can be precluded as a source of energy, because the wells reach their economic limit of production before the force of gravity becomes an important factor in moving oil to the wells. Since the majority of fields produce oil chiefly by reason of the gas pressure in the oil horizons, the following treatment deals mainly with factors that influence gas-energy relationships. Gas-energy Relationships Formation Pressures The gas pressures existing in oil-producing formations may be the result of a combination of several contributing factors. All fluids under

Jan 1, 1932

By Robert C. Collins, Clifford L. Jewett

The development and production of artificially colored roofing granules have been key factors in the success of the asphalt roofing industry. They provide protection for the asphalt from solar radiation and satisfy the home-owner's desire for a wide range of attractive colors. As a result, the asphalt shingle has become the most commonly used roofing material today. In addition to providing a stimulus to the asphalt roofing industry, artificial methods of coloring granules completely changed the nature of granule production from one of quarrying, crushing, and screening to a complex technical operation. Today's roofing granules are the result of many years of research, and they are produced in modern plants to exact specifications. History Asphalt roofing materials available today are the product of a long evolution of technological development. Forerunners of the present bituminous products, appearing as early as 1780, were primitive constructions of burlap saturated with crude tar or pitch. An early improvement to this basic effort was the dusting of talc, mica, or other finely ground material on the coated surfaces to keep the roofing from sticking to itself in storage. At times some pigmentation was added with the dusting material for initial color, but this was far from satisfactory. In fact, this early product possessed none of the qualifications of a good roof surfacing material. It was not economical; it was difficult to handle and apply; it was not attractive; it provided no resistance to fire; and it would not withstand the elements as well as other products then in use. Methods and machines were soon devised to saturate endless webs of felt with asphalt from the fast-growing petroleum industry. Even though saturated felt became available, this product of rags and wood fiber had almost the same limitations as burlap and tar. Even with heavier coatings of asphalt applied to both sides of the sheet for rigidity and longer life, the product still lacked color and fire resistance. Further, it was found that constant exposure to the sun soon caused the asphalt to become brittle, and it eventually cracked and leaked. This led to the first important use for crushed mineral products on asphalt-coated shingles and provided the key to the subsequent growth of the asphalt roofing industry. When a layer of crushed mineral was embedded in the surface exposed to the weather, the asphalt coating was protected from ultraviolet light and retained its elasticity over a much longer period of time. In addition to this protection, the mineral surfacing provided some resistance to fire. Fire resistance in the past had been found only in the expensive slate or tile roofs and the unattractive and expensive metal roof coverings which were then available. The most common mineral granule applied to the early asphalt roofing products as they began to make their first significant advances after 1900 was screened waste from slate quarries. Slate granules being available in dull shades of red, green, black, purple and a few other miscellaneous colors did provide a degree of color. Since slate has a flat platelike cleavage, it provides a cheap protective cover for the asphalt-coated sheets. Records show that coarse slate screenings were used for asphalt roofing as early as 1906. As the asphalt roofing industry developed, many other natural colored rocks and minerals were used to coat the surfaces of the roofing. The list included silica

Jan 1, 1975

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

Secondary minerals are the result of a process of concentration and enrichment and are commonly richer than the primary minerals of the same deposit. Secondary ores that contain abundant sulphides are commonly distinguishable in the field from primary ores; this distinction is more difficult with ores that carry a small quantity only of sulphide minerals, and microscopical examination of the ore in thin section is advisable in all doubtful cases. It is frequently difficult, and in some cases impossible, to determine the primary or secondary character of quartzose gold ores. The safest guide is the presence or absence of gaseous or fluid inclusions in association with the ore minerals; such primary association coupled with a lack of traces of oxidation is indicative of primary origin. Any ore that carries traces of oxidation, such as iron stains, endritic oxides of manganese, kaolin and so forth must be considered to have been acted upon by surface agencies, and secondary enrichment must be suspected. Further examination, however, may indicate that the contained value is primary, and, therefore, persistent in its vertical distribution. The manner of occurrence of secondary minerals is frequently characteristic; secondary minerals, being due to the action of surface waters, are commonly found in cracks through earlier minerals, or as crusts lining vugs or surrounding nucleal masses, or in general, in some distribution later than and not conforming to the arrangement of the primary minerals. Secondary sulphides are often found as soft black pulverulent masses or coatings, although they frequently occur well crystallized or as

Jan 1, 1932

By C Gunther

Secondary minerals are the result of a process of concentration and enrichment and are commonly richer than the primary minerals of the same deposit. Secondary ores that contain abundant sulphides are commonly dibtinguishable in the field from primary ores; this distinction is more difficult with ores that carry a small quantity only of sulphide minerals, and microscopical examination of the ore in thin section is advisable in all doubtful cases. It is frequently difficult, and in some cases impossible, to determine the primary or secondary character of quartzose gold ores. The safest guide is the presence or absence of gaseous or fluid inclusions in association with the ore minerals; such primary association coupled with a lack of traces of oxidation is indicative of primary origin. Any ore that carries traces of oxidation, such as iron stains, dendritic oxides of manganese, kaolin and so forth must be considered to have been acted upon by surface agencies, and secondary enrichment must be suspected. Further examination, however, may indicate that the contained value is primary, and, therefore, persistent in its vertical distribution. The manner of occurrence of secondary minerals is frequently characteristic; secondary minerals, being due to the action of surface waters, are commonly found in cracks through earlier minerals, or as crusts lining vugs or surrounding nucleal masses, or in general, in some distribution later than and not conforming to the arrangement of the primary minerals. Secondary sulphides are often found as soft black pulverulent masses or coatings, although they frequently occur well crystallized or as

Jan 1, 1932

By Reinhard H. Wöhlbier, George E. Aiken

8.4-1. Introduction. Surface excavating is done on a continuous basis with a variety of machines: 1) trenchers and ditchers, 2) conveyor loaders, and 3) bucket-chain and bucket-wheel excavators (BWE). Surface mining is largely concerned with only the last two machines, although some of the conveyor-loader types are often used by contractors for large-scale earth moving, and the engineer should be aware of these applications. This chapter is restricted to discussing only the bucket-chain and bucket-wheel excavators, with special emphasis on the latter. Continuous digging with these machines is done with evenly spaced buckets on either an endless chain or on the periphery of a rotating wheel. The bucket-chain digger excavates and takes the material away from the face with the same machinery. In the case of the bucket-wheel machine, these two functions are separate. Material is excavated by the buckets and then flows in a continuous stream via a transfer to the conveyor system, which in turn transports it to the discharge point. The wheels are adjustable in rpm and mount 6 to 12 buckets of equal size. These are classed as celled, cell-less or semicelled. The digging ladders for both types can move simultaneously in the horizontal and vertical planes. Ladder control is similar to the operation of a bucket-line dredge. Some ladder-chain and all wheel excavators have the machinery deck and superstructure mounted on a 360° swing circle. Other chain diggers have a fixed machinery deck. Deep and/or high cutting models are available in either the chain or wheel excavator. Machines can be either rail or crawler mounted, but the trend is to crawlers. Many of the early ladder-chain, rail-mounted excavators have been converted to crawlers. These may be either of the single or bogie type, depending on the conditions. Large machines usually use the superior three-point crawler suspension.

Jan 1, 1968

J. S. UNGER,* Pittsburgh, Pa. (written discussion ?).-There is a common impression in the minds of many that forging or rolling apiece of steel not alone increases the strength but makes the steel more dense, or causes it to become heavier. I believe it is the author's aim in the paper to show that cast steel is almost as dense as forged steel. The average results obtained by him show very little difference in density, being

Jan 5, 1919

By William Price

DURING the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce risers of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1.

Jan 1, 1937

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high hearing loads and elevated operating temperatures, the life of hearings made from tin-hale or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in hearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on hearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condition, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organizations of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements. Investigation, undertaken with this in view, indicated that the addition of fractional percentages of the metal indium to the cadmium bearing

Jan 1, 1938

By H. I. Aaronson, C. Laird

The kinetics of thickening and of lengthening of ?' plates in an Al-3.93 pct Cu alloy in the temperature range 203" to 300" C were determined by means of transmission electron microscopy. The rate of thickening was found to be less than that allowed by volume diffusion control at all temperatures, by amounts which increased with decreasing temperature, in agreement with the predictions of a general theory of precipitate morphology.1 Thickening was treated on the basis of the ledge mechanism. Ledges were deduced to spread across the broad faces of ?' plates at volume dzjrfusion-controlled rates, as anticipated from the disordered structure of their edges. Lengthening of 8' plates, on the other hand, took Place more rapidly than allowed by volume dzjrfusion. This occurred despite clear morPhological evidence of a bmrier to growth at the edges of these plates. It was concluded that the misfit dislocation structure comprising the barrier requires that lengthening take place by a jog mechanism. The tnisfit dislocations, however, also serve as diffusion short circuits, and allow high overall lengthening rates to be achieved. In Part I' it was shown that, within the range of aging temperatures and times studied, the broad faces of 8' plates formed in Al-4 pct Cu are fully coherent with the a, matrix. Virtually .all of the dislocations present in these faces were found to have developed as a result of plastic deformation in the a phase. Such dislocations are thus "intruders", rather than the more usual misfit-compensating variety. The edges of 8' plates were confirmed, by extension of the earlier studies of Mat-suura and Koda,3 to be made up of edge-type misfit dislocations, in sessile orientation with respect to lengthening of the plates. These interfacial structures should cause 8' plates to thicken and to lengthen at rates less than those allowed under the condition of volume diffusion control, such as would be expected if the interphase boundaries had disordered structures.' The narrow width of 8' plates, the reproducible crystallography of their broad faces, and the appearance of these plates in cross section as octagons rather than as circular discs2 provide qualitative support for these deductions. The present study of the rate of thickening and the rate of lengthening of 8' plates was undertaken in order to examine them on a quantitative basis. I) THICKENING KINETICS OF THE BROAD FACES OF?' PLATES A) Literature Review. The measurements now available on the thickening kinetics of single-phase precipitate plates consist of one plot of the thickening of a proeutectoid ferrite plate in an Fe-C alloy,' showing (as predicted) thickening rates less than those allowed by volume diffusion control. B) Experimental Procedure. Details of the preparation of the 4-3.93 pct Cu alloy used in this study have been previously reported.4 As in Part 1,' transmission electron microscopy was the observational tool employed. A general description of the apparatus and procedures of the electron microscopy studies is given in Section I of Part I. In thin foils, 0' plates tend to form at and parallel to the foil surface.' A direct investigation of the thickening process by means of hot-stage transmission electron microscopy was therefore not feasible. It was thus necessary to use the conventional method of aging individual bulk specimens for a wide range of different times at the various temperatures studied. In each specimen, the thicknesses of a number of plates were measured. Since thin foils prepared from "bulk-aged" material contain a large proportion of grains with orientations near (001) , it was relatively easy to find, near the edges of the foils, the characteristic multifold patterns of intersecting extinction contours which indicate regions where the foil is exactly at an (001) orientation. The thicknesses of large numbers of plates were measured along the (200) branches of the "stars" so that the 8' plates were precisely parallel to the optical axis of the microscope. Wherever possible, intersecting extinction contours were adjusted with the parameter s > 0 to improve the visibility of the plates in bright-field illumination. These precautions, in combination with taking the measurements at the thinnest parts of the foils, minimized the errors in the measurement of the thickness of the plates resulting from inexact parallelism to the electron beam. Since the plates were very thin, it was not easy to measure their thickness on the photographs. The techniques of enlargement and of microdensitometry were employed to minimize errors from this part of the measurement. A further source of possible error, that the plates can appear thicker because of contrast associated with mismatch normal to the plane of the plate, was also considered. The images of the plates were usually thinner than those of dislocations, however, and no anomalous changes in apparent plate thickness were observed when regions of foil containing plates were tilted through various diffracting conditions. Any error from this cause must therefore be small. Other sources contributing errors were: a) the microdensitometer traces per se and the subjective estimates of their peak limits, and b) slight fluctuations in magnification associated with small changes in the current of the objective lens of the electron microscope. The overall error probably amounted to no more than 5 to 10 pct. In order to obtain readily interpretable data on thickening kinetics, it is essential that the diffusion fields of adjacent ?' plates not be allowed to overlap. Calculations'-' showed that this condition is definitely not ful-

Jan 1, 1969

By R. M. Brick

SEGREGATION can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming. steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-12 per cent Si alloys. The phasial condition implicitly described above-solidification over a range of temperatures with a compositional difference between solid. and liquid-is found in nearly all solid solutions or combinations of solid solutions and eutectics. Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually determinable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be. described first because it is an essential part of the picture. CORING Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus 1, 3, 7 and solidus 2, 5, 8, and where the vertical 1, 4, 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. 1b) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1944

By R. M. Brick

Segregation can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-I2 per cent Si alloys. The phasial condition implicitly described above—solidification over a range of temperatures with a compositional difference between solid and liquid—is found in nearly all solid solutions or combinations of solid solutions and eutec-tics, Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually deter-minable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be described first because it is an essential part of the picture. Coring Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus I, 3, 7 and solidus 2, 5, 8, and where the vertical I, 4: 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. Ib) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1945

By Lucien Eaton

THE changes that have occurred in metal mining in the past 75 years include almost everything that we know about modern mining. It is true that in odd corners of the world mining is still carried on as it was before that period, but in the United States such instances are rare. Everything has changed to some extent. Even picks and shovels have changed in design and materials. At the beginning of this period steam power had been used for pumping and hoisting for nearly 75 years, but almost every other operation underground was performed by manpower. Although mining was carried on in a small way east of the Appalachian Mountains before the Revolution, and continued thereafter on an increasing scale for more than 100 years, it was not until the discovery of the iron and copper deposits in Michigan and Minnesota and the opening of the mineral areas of the West after the building of the transcontinental railroads that the real development of modern metal mining began. In the same period many problems of deep mining in South Africa were solved by new techniques in shaft sinking and hoisting. Before this time knowledge of mining and skill in its performance were handed down from father to son by the apprentice system, and the son learned to do things in the way his father and grandfather had done them. The rapid expansion of mining in the United States after the Civil War required more men than the apprentice system could supply, and the

Jan 1, 1947

By C. E. Johnston

In December 1956, International Minerals & Chemical Corp. installed a rope-suspended belt haulage system in its Carlsbad, N. M., potash mine to complement the already existing rail transport arrangement. In this article the author describes when and where each system is used, the advantages and disadvantages of both, and future planning and proposed changes in haulage at IMC. The haulage system at the International Minerals & Chemical Corporation (IMC) potash mine near Carlsbad, N. M., reached a turning point in December 1956 with the introduction of rope-suspended belt haulage. In fact, IMC pioneered the use of this type of belt in the potash industry. Since that time belt conveyance has been employed as an extension of the rail system but not as a replacement of the main rail haulage. IMC's potash mine is located in the Permian Basin, approximately 20 miles east of Carlsbad in Eddy County, N. M. The 800, 850 and 900-ft levels have been exploited. From these levels over 60 million tons have been extracted. The two ore minerals are sylvite (KCl) and langbeinite (K2SO4. 2MgSO4). The principal gangue mineral is halite, with minor amounts of polyhalite, kainite and leonite. Langbeinite is mined on the 850-ft level and sylvite on the 900. The 800-ft level, with both langbeinite and sylvite mineralization, is idle. Mining heights vary from 54 in. to over 10 ft. A room and pillar mining system is used. Geologically, mining is done in the Salado salt formation. The U.S. Geological Survey has classified the 900-ft sylvite level as the first ore zone and the 850-ft langbeinite level as the fourth ore zone. Since the grade of sylvite is low, mineralization at the IMC mine is somewhat irregular and salt horses, are common. Selective mining and a flexible haulage

Jan 1, 1963