Search Documents

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

EXPERIMENTAL results of the last decade have shown that both accelerator particles and reactor radiations produce significant changes in the properties of metals. These changes, called radiation damage, are important from both academic and engineering viewpoints. An understanding of the radiation damage produced by reactor radiations is difficult, because many kinds of particles having varying energies are present. Therefore, many fundamental studies are being conducted using accelerators in order to obtain nearly mono-energetic beams of various charged particles. Furthermore, many of these experiments are conducted at low temperatures in order to freeze in the radiation-produced lattice defects, after which the specimens are annealed to study the movement of the defects. It is found that although much of the low temperature radiation damage disappears by annealing at room temperature, a significant amount remains. Because there is no assurance that irradiation followed by annealing at a higher temperature will produce the same effect as irradiation at the higher temperature, and because there is an immediate interest in reactor radiation effects during exposures at and above room temperature, a major program is in progress at this laboratory to investigate some of these effects. This paper, representing a part of the program, compares the radiation damage to a group of metals which were exposed under nearly identical irradiation conditions. The metals, representing the three major crystal systems, include copper, nickel, titanium, zirconium, iron, molybdenum, and type 347 stainless steel. The effects of reactor radiations have been treated from a theoretical viewpoint by Seitz' and Ozeroff.' The problem considered by them has been the atomic displacements produced in an infinite medium by mono-energetic beams of both neutrons and charged particles. For reactor experiments, this treatment is not wide enough in scope, because specimens and reactor components are finite, and there are continuous energy spectra of the various particles. Therefore, the theoretical considerations will be extended in this paper to cover reactor conditions and the findings will be compared with the observed radiation damage. Experimental Materials—The six basic metals for this investigation were of commercial or higher purity, and the type 347 stainless steel was of commercial quality. These materials were supplied in various forms ranging from ingots to finished rods, and were fabricated to rods approximately % in. in diam and annealed for specimen stock. A summary of data pertinent to these materials is shown in Table I. The values for chemical compositions include both actual analytical values and typical values supplied by the manufacturer. More information concerning typical

Jan 1, 1957

By John Alden

A CONSIDERABLE PROPORTION of the tonnage of aluminum used today has at some stage during its manufacture, been rolled. I. For one, therefore, was particularly pleased to hear that this Society was to hold a symposium on rolling of nonferrous metals. Metallurgists can well afford to direct their close attention to the metallurgy involved in this important operation. To one who has seen today's high production rolling mills for aluminum it is difficult to realize that the first aluminum rolling mill For sheet was installed a scant 55 yr ago, in 1892. This mill was a three-stand train of 2-high mills, driven by a steam engine and was operated for many years successfully rolling aluminum sheet. Mills for the rolling of aluminum rod were installed in 1899 to meet the demand For manufacture of electrical conductor wires and cables. Bars and rods in straight lengths were also made. While these mills were the first built for rolling aluminum products of these types some rod had previously been rolled on brass and copper mills. Not until many years later, in 1929, however, Were facilities provided for the rolling of structural shapes, such as I-beams and channels. Growth of the aluminum sheet business and the necessity for economical manufacture soon brought the realization of the economies resulting From-the rolling of sheet in long lengths and coiling it. A five-stand continuous mill driven by a steam engine, was in operation late in 1907. This took aluminum slabs coating from

Jan 1, 1948

By E. A. Gulbransen, J. W. Hickman

IN a previous paper1 the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300° to 700°C. except for copper, where the range selected was 100° to 500°C. The results of these studies were presented in graphical form as existence diagram, of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviations in lattice parameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: I The existence diagrams of various alloys. [2.] The effect of the structure of the [ying] metal on the existence diagram of Iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body- centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K42B1 Nichrome V, Hipernik, Inconel, Stellite " 21," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1946

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

A. L. FIELD, Cleveland, Ohio (written discussion*.-)In equation 2, B is used to denote the ratio of bases (lime plus magnesia ) to acids (alumina plus silica) it being stated that this ratio gives more concordant results than the ratio either of bases to silica, or of lime to silica. I find, however, that, by making use of the ratio between true CaO (CaO by analysis minus sulfur calculated to CaS) to acids, equation 2 may he modified to agree with the observed facts within an average error of 0.0041 per cent. sulfur instead of 0.0045 per cent. The revised equation is s = 0.072 + 0.01835 - 0.00061 (t - 1400) - 0.0403B where B is the ratio of true CaO to Al2O3 Plus Si02, and the other symbols have the same significance as before. I would not appear to stress too much this slightly better agreement of the revised equation with the observed sulfur. Yet I believe that the use of this ratio of true CaO to acids is to be preferred, if for no other reason than the fact that it is more in harmony with the previous findings of the Bureau of Mines with regard to the effect of magnesia and other impurities on slag viscosity.1

Jan 12, 1919

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways, and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard-rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed. Mining, from exploration through refining, is essentially a process of sorting in which the payable mineral, or metal, is progressively separated from the other constituents of the earth&apos;s crust with which it was originally associated. This takes place more distinctly at each step of the operation. What is it that determines the degree to which sorting should be carried out at each of the several steps comprising a whole mining operation? The formal answer is that degree of sorting at each step which results in the lowest overall cost for the complete separation. In practice, individual steps are chosen from those available in current technology, each of which effects a degree of sorting such that the quantity of material which must be sorted in the succeeding step is economically acceptable. It follows that any new technological development has repercussions throughout the whole mining operation and, more important, that the solution to excessive costs in any one step of the operation may lie not in improving the costly operation itself so much as in increasing the degree of sorting preceeding that operation. This concept, particularly in relation to deep-level mining of thin, tabular gold-bearing reefs in South Africa, is discussed here, and the most recent results achieved in the development of hard-rock cutting machines for stoping more selectively than is possible with explosives are presented. Deep-Level Mining Deep-level mining involves operations which are either not encountered, or are of only trivial importance, in near-surface mining. Near-surface, the major operations are those of rock breaking, transport, and milling. In deep-level mining, hoisting, environmental control, and strata control assume major importance. Some idea of the relative magnitude of these operations may be gained by comparing the separate amounts of energy which are required, or which must be controlled, to effect the various operations when, say, mining a tabular deposit 40 in. thick at 8000 ft below surface, Table 1. It is true that the costs of handling a given quantity of energy are not the same for each operation. Nevertheless, Table 1 does emphasize the fact that the operations of hoisting, strata control, and environmental control are of unique and major significance in deep-level mining. In particular, hoisting and environmental control place a heavy load on the reticulation system of the mine—the shafts, haulages, and airways. Typically, a new, deep gold mine with an annual revenue of about $35 million requires a total capital expenditure of about $140 million of which some $100 million is invested in developing and equipping this reticulation system. The ratio between annual turnover and capital invested of about one-quarter is exceptionally low, and it typifies the poor utilization of capital by the current technology of mining hard rock at depth. The average thickness of the reefs in the new South African goldfields varies from 10 to 30 in.,l and even in the thicker reefs the gold is often confined within a small fraction of the nominal thickness. Nevertheless, it is universal practice to mine these reefs at a stope width of about 40 in. or more, so that the quantity of rock broken in the stopes and hoisted out of the mine is between two and ten times the quantity of rock actually carrying a significant amount of gold. The reason for the adoption of such excessive stope widths is to be found in the method of rock breaking by drilling and blasting. The only free surface to which a blast hole can break is the stope face. It follows2 that each hole cannot have a burden in excess of the height of the free face if it is to break satisfactorily. To

Jan 1, 1971

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

Since the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error. Introduction The steady-state flow of gas through a porous material—that is, flow wherein the boundary conditions do not vary with time—is subject to analytical solution. Muskat1 has shown that the general differential equation is simply the La Place equation in P2. Direct solutions may be at once obtained. The unsteady state, on the other hand, is not analytically reducible. Since nearly all phenomena of practical interest in gas production involve flow in the unsteady rather than in the steady state, it has been necessary to derive approximate Solutions to the general equation. The validity of such approximations has not hitherto been adequately tested. In the experiments to be described a simple, closed, linear system is substituted for the real complex gas field. The general results, however, are independent of the geometry Of the system&apos; The problem studied is the rate of production, and the accompanying variations in pressure, when one end of a linear porous system is opened to the atmosphere and permitted to produce to exhaustion. An approximate solution to the general differential equation, based upon the assumption of an "infinite series of steady states," is then applied to the results to determine the validity of this method of dealing with actual reservoirs. Theoretical Considerations The fundamental differential equation governing the flow of a gas through a Porous medium can be derived easily from the equation of continuity, Darcy&apos;s law, Boyle&apos;s law and a statement of the thermo-dynamic nature of the flow. For isothermal flow it is: d2P2/dx2 + d2p2/dy2 + d2p2/dz2 = 2fµ/K dP-dT

Jan 1, 1942

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

Since the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error. Introduction The steady-state flow of gas through a porous material—that is, flow wherein the boundary conditions do not vary with time—is subject to analytical solution. Muskat1 has shown that the general differential equation is simply the La Place equation in P2. Direct solutions may be at once obtained. The unsteady state, on the other hand, is not analytically reducible. Since nearly all phenomena of practical interest in gas production involve flow in the unsteady rather than in the steady state, it has been necessary to derive approximate Solutions to the general equation. The validity of such approximations has not hitherto been adequately tested. In the experiments to be described a simple, closed, linear system is substituted for the real complex gas field. The general results, however, are independent of the geometry Of the system&apos; The problem studied is the rate of production, and the accompanying variations in pressure, when one end of a linear porous system is opened to the atmosphere and permitted to produce to exhaustion. An approximate solution to the general differential equation, based upon the assumption of an "infinite series of steady states," is then applied to the results to determine the validity of this method of dealing with actual reservoirs. Theoretical Considerations The fundamental differential equation governing the flow of a gas through a Porous medium can be derived easily from the equation of continuity, Darcy&apos;s law, Boyle&apos;s law and a statement of the thermo-dynamic nature of the flow. For isothermal flow it is: d2P2/dx2 + d2p2/dy2 + d2p2/dz2 = 2fµ/K dP-dT

Jan 1, 1942

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw&apos;1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By A. P. Cohen, D. W. Fuerstenau

Methods of accounting for the feed size in analyzing the size distribution shift during comminution have been discussed in a number of papers.1,2,3 Based on experiments which charles2 performed with single Pyrex specimens, Schuhmann4 pointed out that the size modulus of an assembly of particles should be determined by the energy expended per unit volume (or mass), independent of the size of particle being comminuted. In this same paper, Schuhmann derived the Charles energy-size reduction relationship by considering that complex comminution operations can be considered to be the summation of many individual comminution events, each of which must be governed by Were 6wi is the mass of a particle receiving the impact, 6Ei is the energy delivered to the particle, ki is the size modulus of the product resulting from the impact, a is the distribution modulus of the assembly of particles, and A is a constant. Recent experiments on the compression loading of Pyrex spheres ranging in size from 1/8 to l-in. diam have shown that the size modulus of the fragments is determined by the strain energy at fracture per unit mass, independent of sphere diameter.&apos; The objective of the present investigation has been to determine experimentally whether the size distribution of the product from such a complex comminution process as rod milling is determined only by the energy expended per unit mass independent of feed size. Samples of each Tyler sieve fraction ranging from 4x6 to 48x65 mesh were prepared from crushed Brazilian quartz crystals. One kilogram of each fraction was ground at 60 pct solids in an 8x9 1/4-in. mill containing 17.5 kg of rods (26 rods, 5/8-in.; 10 rods, 3/4-in.; and 5 rods, 7/8-in. diam). In each test, the mill was run at 77 rpm for 15 min. Size distributions were determined by a wet-dry sieving technique. Table I presents the size distribution of the products obtained by grinding each of the size fractions. Because the size distributions are so nearly alike, they are plotted in Fig. 1 by shifting each size distribution for the different feed sizes one screen fraction to the right. Thus, the lowest point in each size distribution represents 400 mesh and each of the other sieve sizes must be shifted accordingly. A single regression line was calculated by combining the data for the six tests, excluding the coarsest feed and the two finest feed fractions. 6 This regression line, which is given by (Y \0.88 where y is the cumulative percentage of material

Jan 1, 1962

By David E. Fogelson, James J. Olson

Rock mechanics as a guide to a safe underground operation is gaining importance as more is under- stood of rock behavior under stress and of the competency of rock after blasting. The U. S. Bureau of Mines&apos; Twin Cities Mining Research Center and White Pine Copper Co. personnel undertook a joint research program recently to define how the rock adjacent to a newly opened underground working could be left as undisturbed as possible. The goal was to leave a competent structure which would tend to limit rock falls and thus decrease the incidence of fatalities from this greatest of all underground hazards. High-amplitude stress waves and borehole gases create a crushed zone in the rock, the thickness of which is about equal to the borehole radius. Beyond the crushed zone, additional structural damage occurs to the rock from the microstructural level up to visible fractures that may extend several feet. This type of rock damage near the final excavation lines reduces rock strength and increases the possibility of failure of the openings from subsequent vibrations or stresses.

Jan 9, 1969

By Carroll Wegemann

THAT Colorado was producing oil and gas before the fields of the Mid-Continent were discovered is a fact too frequently overlooked. As early as 1862, oil was obtained in the Florence district (see Fig. 1) from seepages and shallow holes. The first well that could be regarded Fig. 1. as being truly commercial was drilled in this field in 1876. The field is now producing 100,000 bbl. per year, and is credited with a total production of approximately 11,000,000 bbl. The small field near Boulder, Boulder County, was opened in 1901; production has now practically ceased but the field is credited" with a total production of 610,000 bbl. Oil was discovered at Rangeley in 1901, and the field supports a small local refinery at the present time. The first shallow well in the White River gas field was drilled in 1892, and the wells now producing have been

Jan 3, 1925

By Leland Wemple

PREVIOUS to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, i.e., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, i.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was pre-determined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into "grades suitable for brash was that of redistillation.

Jan 11, 1917

By James A. Barr

Phosphate rock is a natural rock containing one or more phosphate minerals usually calcium phosphate, of sufficient purity and quantity to permit its use, either directly or after beneficiation in the manufacture of commercial products.1 The principal minerals in phosphate rock have the apatite structure which may be represented by the type formula: Ca10(X2) (PO4)6 where X represents the hydroxyl group (OH), chlorine or fluorine, either singly or collectively. The calcium may be partly replaced by sodium, magnesium, and other positive ions such as manganese, strontium, lead, uranium, cerium, yttrium and other rare earths. The PO4 radical may be partly replaced by small quantities of UO4, AsO4, SiO4, CO3, SO4, or Vo4. A typical commercial rock is usually a calcium phosphate containing 3 to 4 pct fluorine, the major impurities being limonite or other iron oxides, clay, aluminum phosphates and silica as quartz sand. A little vanadium is present in most of the domestic rock deposits (except the Tennessee Brown Rock), according to Jacob, Hill, Marshall and Reynolds! A little uranium occurs in the Florida leached zone, as will be brought out later. The chemical analyses are reported as P205, or tricalcium phosphate Ca3(PO4)2, the latter often designated by the trade name BPL (bone phosphate of lime). Commercial analyses usually report iron and alumina as oxides, lime as CaO and silica or insoluble. Colony3 examined many samples of apatite, staffelite, dahlite and American phosphorites and concluded that all have identical X-ray diffraction patterns. The phosphates in the phosphate rock have very minute crystalline structures. The mineral apatite Ca3(F.Cl) (PO4) 3 is the principal primary source of the element phosphorus, and occurs widely distributed in igneous rocks but rarely in a minable mass. Only about 12 pct of the world production of phosphate rock comes from primary apatites; the remainder is derived from secondary phosphorites. These phosphorites have been formed by the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rock containing apatite, bone deposits of prehistoric animals, marine life or guano deposits. These phosphorites are mostly alterations of phosphatic limestones. The sedimentary phosphate deposits are of marine origin and may have been enriched by subsequent solution of the more soluble calcium carbonate by waters containing carbon dioxide, by physical concentration by wave action, and by redeposition of the dissolved phosphate ions. Uses of Phosphate Phosphorus is the spark of life and is the structure builder and one of the main elements of plant food (fertilizer). Without phosphorus, life cannot exist. A "complete" plant food[t] in addition to phosphorus compounds contains potash, which acts as a catalyst to convert nutrients to useful forms, nitrogen to supply the growth element and many minor elements. The cycle of supply of phosphorus is from the apatite to solution and soil, absorption of plant life, decay and return to the soil or by animal life feeding on the plants. With insufficient supply of phosphorus in vegetation, life is not prolific. If crops are removed from

Jan 1, 1960

By L. E. Wemple

Previous to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, ie., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, z.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was predetermined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into grades suitable for bras4 was that of redistillation.

Jan 1, 1918

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,&apos; but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."&apos; Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."&apos; It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,&apos; by Hancock in 1947," and by the national French research agency Cerchar in recent years.&apos; In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,&apos; but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."&apos; Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."&apos; It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,&apos; by Hancock in 1947," and by the national French research agency Cerchar in recent years.&apos; In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

CALAMINE is one of the semiminerals that have great similarity to the metals. It is a very heavy mineral earth of a yellowish color. It is found in Germany near the lead mines and in Italy in a mountain between Milan and Como. It is also found, as I have heard, in other places, as at Fosini in the territory of Siena. I believe that it is almost certain that some exists there because there are many other kinds of minerals there- about, although none is mined there in these times. But this does not mean that it could not be mined or that there is not some there that is real. Someone says that he med to melt what he could find with copper [36v]

Jan 1, 1942

By R. W. Raymond

In June, 1906, I delivered to the graduating class of Lehigh Cniversity an address upon this subject, the substance of which, with sundry omissions and additions, was subsequently repeated, in October of the same year, in an extempore address before the Schenectady branch of the American Institute of Electrical Engineers. The latter, as stenographically reported, was published in the Proceedings of that society for November, 1906, and was referred to by President John Hays Hammond in his address at the Chattanooga meeting of October, 1908. Requests have been received from various quarters for the repub-lication of this address by the Institute. This I do not regard as necessary or proper; but I yield to that demand so far as to reproduce in the Transactions a summary of my views, as expressed in the two addresses above mentioned.

Jan 1, 1911

By Ben Gumpertz

The important factors in any study of the screening of sand with a gravel envelope, as applied to use in oil wells, are: (I) sand size and shape, (z) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,&apos; from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 13 times the grain size at the ten-percentile analysis of the formation sample." ?;his applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity." Also, it has been assumed by some operators that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffective screen. Thus the purposes of this work are: 1. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screening action of varying the thickness of the gravel screen. 3. To investigate sand migration in the gravel screen and the effect of flow velocity and gravel size upon sand migration. Description of Apparatus In an attempt to reproduce field conditions for the purposes of this investigation, a flow tube was constructed, according to the manner of Urenj3 to represent a radial drainage segment of an oil sand. To arrive at the dimensions of the flow tube, a radial drainage segment of rectangular cross section was assumed to define an area of z sq. in. on the face of a well 6 in. in diameter. From this the dimensions of the segment were calculated out to a distance of 5 ft. from the face of the well. By computing cross-sectional areas at a number of sections along the rectangular segment and transforming these areas into the circular form, a drainage cone was obtained having everywhere the same cross-sectional area as the drainage element of rectangular cross section. To construct the apparatus, two sections of pipe of 7%-in. inside diameter, one 13 in. and the other 4 ft. long, were joined by a bolted flange. A mandrel having the dimensions of the drainage cone was centered in the pipe and a neat cement mixture was cast around it. A protective gasket was placed between the two sections of pipe so that the cement body could be separated at that point. When the mandrel was withdrawn a drainage cone was obtained (Fig. I).

Jan 1, 1941