Search Documents

By R. A. Vandermeer

It is usually assumed that the rate-determining step in the migration of a grain boundary involves the thermally activated transfer of single atoms across the interface. Chemical reaction rate theory then gives a migration rate which is proportional to the driving force when this is small compared to kT.1 In their recrystallization studies on aluminum, Gordon and vandermeer2 obtained data which was capable of providing the first experimental test of this proportionality. They correlated stored energy (driving force) release measurements determined calorimetrically with fraction recrystal-lized kinetic (growth rate) data acquired metallo-graphically at a temperature where a significant amount of recovery takes place concurrently with recrystallization. Within experimental error, the results of Gordon and Vandermeer confirmed experimentally, at least over a limited range, the linear dependence of boundary migration (growth) rate on driving force in accordance with theory. In obtaining these results, however, an incorrect, implicit assumption was made in relating the average instantaneous growth rate of the recrystallized grains to the measured fraction recrystallized kinetic data. The purpose of this present note is to point out and correct this assumption. An alternate approach, whereby a more proper average growth rate can be calculated from the recrystallization kinetic data, is presented. The earlier data, reevaluated in terms of this new approach, show the same general trend as before so that the original conclusion of Gordon and vandermeer2 is still valid. As was shown in a detailed study3 of the geometrical features of recrystallization in aluminum, the colonies of recrystallized grains can be regarded as uniform cylinders embedded in a three-dimensional matrix, the number of such colonies being constant. Thus during the early stages of recrystallization the volume fraction recrystallized, Xv, can be written as Xv=ynvlr2 [l] where y is a shape factor and i and r are defined as the average length and radius of a recrystallized colony and are spatial averages over the specimen. -nv, is the number of such colonies in a unit of volume. The erroneous assumption made in the earlier paper2 was that r in Eq. [I] could be replaced by

Jan 1, 1965

not weaken. I saw him shortly before he was killed; his conduct under fire was splendid and an inspiration to his men. His loss is felt deeply by all ranks. Thanks to him and to others, who like him, paid the full measure of devotion to their country, our line was held until the critical situation in that vicinity was at an end. He died the true death of a soldier, with his face to the enemy. As we now look back, it is easy to believe that this holding of the line of defense intact by General Carey and his men was a determining factor in the outcome of the war. To have played so important and noble a part in this vital effort as that taken by Perry is assuredly the privilege of few. Our lives, it seems, are like capital entrusted to us to be expended as wisely and effectively as we may. With them we purchase whatever of accomplishment the stuff that is in us permits. It is impossible to escape profound regret that a career so full of the highest promise, and a personality so overflowing with all that is fine and lovable, should have been cut short at the age of thirty-one. Yet who can doubt that in a few months Perry bought with his life the fullest achievement of a life-time—a glorious part in the salvation of Liberty and Justice and Decency, indeed of Civilization itself! L. C. Graton.

Jan 1, 1920

not weaken. I saw him shortly before he was killed; his conduct under fire was splendid and an inspiration to his men. His loss is felt deeply by all ranks. Thanks to him and to others, who like him, paid the full measure of devotion to their country, our line was held until the critical situation in that vicinity was at an end. He died the true death of a soldier, with his face to the enemy. As we now look back, it is easy to believe that this holding of the line of defense intact by General Carey and his men was a determining factor in the outcome of the war. To have played so important and noble a part in this vital effort as that taken by Perry is assuredly the privilege of few. Our lives, it seems, are like capital entrusted to us to be expended as wisely and effectively as we may. With them we purchase whatever of accomplishment the stuff that is in us permits. It is impossible to escape profound regret that a career so full of the highest promise, and a personality so overflowing with all that is fine and lovable, should have been cut short at the age of thirty-one. Yet who can doubt that in a few months Perry bought with his life the fullest achievement of a life-time—a glorious part in the salvation of Liberty and Justice and Decency, indeed of Civilization itself! L. C. Graton.

Jan 1, 1920

By G. F. Comstock

In the literature of metallography there is a large amount of material describing the various non-metallic inclusions found in iron and steel, and the appearance of sulfides, silicates, oxides, or alumina in steel under the microscope is fairly well known. The inclusions found in non-ferrous metals are, however, not so well known, at least judging from published writings, and the author has been interested in examining small castings of copper, brass, or bronze with certain inclusions purposely mixed with the metal, to see what was the characteristic appearance of each kind of inclusion, and if they could be readily distinguished from one another. The method employed in most cases consisted in overheating and oxidizing a small charge of copper, then cooling it somewhat, and adding a suitable amount of the element whose oxide it was desired to observe. This element was stirred in well and given time to react with the oxygen in the copper, then the melt was poured in a sand mold in the form of a cylinder about 21/2 in. (63 mm.) in each dimension, with a sprue about 11/2 in. (38 mm.) in diameter and 3 in. (76 mm.) high on top of the cylinder, the sprue forming the only riser. Samples for examination were cut sometimes from the center of the casting, and sometimes from the sprue or riser. A few of these samples were cast in chill molds. The appearance of sulfides was studied in an alloy containing 10 per cent, each of tin and lead, with which a flux of plaster of Paris was used. The appearance of foundry sand was studied in several alloys, one of them having sand stirred into the metal intentionally, and others having cut into the molds badly when poured, so that the castings were spoiled by included sand. As all this work was done on alloys having copper as the chief ingredient, the natural starting point was copper oxide, the appearance of which in a micro-section is well known. Cuprous oxide is soluble in molten copper, but separates out in freezing and forms a eutectic containing 3.5 per cent. Cu20, or 0.39 per cent. oxygen. If there is less

Jan 1, 1919

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.' The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By N. J. Grant, A. W. Mullendore

Three aluminum alloys of 0.94, 1.92, and 5.10 pct Mg, prepared from very high purity metals, were tested at 500°, 700°, and 900°F in creep rupture. The degree of strengthening through solid-solu-tion alloying and the effects on the deformation characteristics and fracture were examined. The ductility of the alloys as a function of stress and temperature was closely followed. STUDIES of the creep process in pure metals in recent years have done much to expand the understanding of the fundamental deformation and recovery processes that contribute to overall creep behavior. In order that this knowledge may be applied to commercial alloys, it is necessary to know the principles governing the effect of alloying on the mechanisms of creep. A limited amount of work has been performed in this field, but few investigators have attempted to follow the changes in particular creep mechanisms with alloying. Recently, studies of the effects of solid-solution alloying on the plastic properties of aluminum have been conducted by Dorn, Pietrokowsky, and Tietz,1 Sherby, Anderson, and Dorn,2 and Sherby and Dorn.3 This paper presents the results of an investigation of the effect of solid-solution alloying of high purity aluminum with magnesium on the creep-rupture properties, and correlates these observations with changes in the creep mechanisms. This work is thus an extension of the creep-rupture observations of Servi and Grant4,5 and the deformation studies of Chang and Grant.6,7 Experimental Procedure Three alloys of aluminum containing approximately 1, 2, and 5 pct Mg were tested. These alloying additions are all within the solid-solubility limit at the testing temperatures.' The analysis of the materials is presented in Table I. The tests fall into two categories: l—creep-rup-ture tests at 500°, 700°, and 900°F, and 2—structure study tests performed primarily at 700°F. Speci-mens of 0.160 in. diameter with milled flats for metallographic observations" ' were utilized for the structure studies. All specimens were annealed in one step to give the desired grain size for the tests. Table II presents the annealing data and final grain sizes. The specimens were polished electrolytically before testing with Jacquet solution (2/3 acetic anhydride, 1/3 perchloric acid) at 25" to 30°C, and 15 to 20 v. Creep-rupture testing was performed under constant load with the apparatus previously described." Results and Discussion Creep-Rupture Properties: The log-log plots of creep-rupture data are presented in Figs. 1 and 2. For these very pure single-phase alloys, the minimum creep rate and the rupture life both exhibit straight-line dependence on stress in this method of plotting as they have for commercial alloys0,10 and for pure aluminum." Curve breaks, based on the use of straight-line segments, at 500°F have been found by metallographic study to correspond to a transition from low to high temperature behavior and so represent zones of equicohesion. Specimens on the high creep-rate side of the break showed normal granular deformation processes whereas those on the low creep-rate side showed rapidly increasing grain-boundary sliding and migration with extensive evidence of intercrystalline cracking at 500°F. Two micrographs of the 0.94 pct Mg alloy, Fig. 3, show the increased participation of the grain boundary in the deformation process at 500°F with decreasing stress. In Fig. 3a is shown the structure of a specimen which exhibits little deformation along the grain boundaries and failed transgranularly; in Fig. 3b is shown the increased deformation along the grain boundaries at a lower stress for a specimen which showed appreciable intercrystalline cracking. The severity of intercrystalline cracking increased with increasing magnesium content at 500°F. Intercrystalline cracking disappeared in most of the specimens at 700°F and persisted only in the 5 pct Mg alloy at high creep rates. At 900°F all of the specimens deformed with extensive grain-boundary participation, including extensive grain-boundary migration. None of the alloys at 900°F showed intercrystalline cracking.

Jan 1, 1955

By A. R. Sims

Are from the Greater Butte Project is hoisted through the new Kelley shaft. In 1946 when plans were formulated for the Kelley mine, two test cave blocks were mined by using the facilities of the old St. Lawrence mine. These blocks, known as the Adams No. 1 and Adams No. 2, produced more than half a million tons of ore. The experiment proved beyond all doubt that cave mining was possible- and economical-in Butte. Adams No. 1 was patterned after Inspiration cave blocks. Adams No. 2 was a slusher type, with the slusher lane on the first floor above the haulage crosscut and at right angles to it. Thirty-horsepower electric hoists slushed ore from 48-in. scraper buckets directly into cars for haulage to the shaft. These cars were the 57-cu ft Granby type hauled by 6-ton battery locomotives over 40-lb, 18-in. gage track. Prior to this time the largest slushing machines used at Butte were 15-hp electric hoists pulling 36-in. scrapers.

Dec 1, 1956

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By C. O. Brawner

The advent of larger drilling, excavation, and milling equipment is resulting in a tremendous increase in the scale and annual tonnage of open pit mining. At the present time, open pits up to 3000 ft. deep, and tailings dams and waste dumps up to 600 ft. high are being planned. One of the major problems that projects of this magnitude create is stability. Stability at open pit mining developments must be assessed for tailings dams, waste dumps, and open pit slopes in overburden soil and in rock. Soil mechanics principles are used to assess the stability for the first three. This science was developed by Dr. Karl Terzaghi in the 1920’s, and since that time the theories and principles have been tested and evaluated. This experience has resulted in the development of sound theoretical concepts, workable sampling and testing techniques, and accurate methods of analysis. Typical problems that can be analyzed include: -bearing capacity of soil under dams and waste dumps. - amount of seepage under and through dams. - stability of slopes and determination of safe slope angles for tailings dams, waste dumps, and open pits. - influence of earthquakes on stability. - influence and cost of different excavation and construction techniques. To assist in comparing engineering experience, an international soil classification system has been developed and used for several decades. In addition, many excellent text books are available outlining soil mechanics principles and techniques. A high degree of technology exists in soil mechanics. This, the mining engineer cannot afford to ignore. If soil mechanics principles had been applied, many major failures involving tailings, tailings dams, or waste dumps, such as those at Aberfan, Mufulira, Luanshya, and El Cobre would not have occurred. Tailings dams are planned in Canada that will be up to 600 ft. high. Construction procedures used in the past have paid little attention to the compaction of the shell material or to the influence of earthquakes on stability. This neglect has led to failures. While failures in low dams may not be too serious, for high dams such failures could have catastrophic results. Another major area of concern is the stability of rock slopes. From the standpoint of long

Jan 1, 1971

By A. W. Fahrenwald

The physics and chemistry of the flotation process are not well understood. Many papers dealing with the theory of flotation have been published but most have been narrow in their viewpoint. No theory advanced has done more than explain, more or less satisfactorily, various isolated phenomena. Scientists have done little with the problem, doubtless because they have not seen sufficient of the practical side of the subject to have their interest aroused. Any attempt to explain the mechanism of flotation that considers only contact angles, surface tension, adsorption, the floating of needles, flocculation, or any other single and narrow phase of the question is sure to be disappointing. Flotation is a problem of colloid chemistry and must be studied as such. In a broad general way, flotation is a process involving and operating by virtue of surface reactions. The term "surface reactions" may be open to criticisms. Many chemists give the term "reactions" a definite and restricted meaning and to such the term may connote change in atomic grouping in strict stoichiometric ratios. While Langmuir looks upon adsorption as a reaction, and there is much evidence in support of this view, we may look on adsorption as a physcial process as far as this paper is concerned. The term seems well suited to the work in general. Presumably these reactions are reactions between the same kinds of forces (electrical) and differ only in degree and in the surface manifestations produced. This premise seems logical if we accept the theory that the atoms of dl elements are made up of grains of electricity, having mass and charge, called electrons; and that atoms differ from one another only in the number and arrangement of the electrons about a positive nuclear

Jan 1, 1924

ON Coal's Horizon one development rises above all others. That is the swift expansion of output to make Soviet Russia the largest coal producer on earth next to the United States. Few Americans are aware of the speed and extent of that expansion nor of the accompanying creation of a strong, resourceful mining machinery industry, nor of the extent and character of the mechanization of Soviet coal mining. Two initial clarifications are necessary for better understanding. First, we must keep in mind the sharp distinction between the Russian people and the communist Soviet dictators who rule them. The great mass of the Russian people are not members of the Communist Party as people here are Republicans or Democrats. They are not permitted to be members. There are, by various estimates, only 2 to 4 million members of that party in all Soviet Russia. The other 196 to 198 million are the victims of their tyranny and their terror. It is the activity of the Soviet rulers that concerns us here.

Jan 1, 1954

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By C. A. Hartnagel, D. H. Newland

Most of the petroleum produced in New York State is obtained by flooding; that is, water drive. No important oil fields have been developed during the past 30 years, nor does there seem much hope that the productive oil areas will be substantially enlarged in the future. There is some prospect that additional supplies may be obtained by deeper drilling, but deep tests for gas to the Oriskany sandstone in some of the oil-producing areas have been without results so far as any discoveries of oil are concerned. Although the flooding method had been made legal in 1919, and some floods had been in operation previous to 1921, that year marks the beginning of a rapid increase in oil production by the new method. The flush production of oil in New York was in 1882, shortly after the discovery of the Richburg pool in Allegany County. The oil production in that year amounted to 6,685,000 bbl. The 1937 production of 5,478,000 bbl. was the largest since the flush production of 55 years ago. The effectiveness of water-flooding for increasing oil production from the old New York fields is shown in Table 1. Table 1.—Production of Oil in New York since 1921 Year Barrels Year Barrela 1921 988,000 1929 3,377,000 1922 1,000,000 1930 3,647,000 1923 1,250,000 1931 3,363,000 1924 1,440,000 1932 3,508,000 1925 1,695,000 1933 3,181,000 1926 2,242,000 1934 3,804,000 1927 2,603,000 1935 4,236,000 1928 3,377,000 1936 4,633,000 1937 5,478,000 The area of the New York oil fields is about 60,000 acres. It has been estimated that not over one-fourth of the area is being flooded. Very little of flooded territory has ceased to produce. Some leases flooded by the early, less scientific methods are being again subjected to the water

Jan 1, 1938

By Robert J. Morris, John N. Butler

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:l are possible on head assays of 0.10 to 0.50 pct U308. Additions of certain base metal salts aid in recovery and materially in- crease the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals.

Oct 1, 1956

By E. E. Malouf

With the continued development of low-grade porphyry copper deposits by open pit mining, substantial amounts of copper-bearing strip material have been accumulated in waste dumps adjacent to the many large mines. Since the end of World War II, the production of copper from leaching these copper-bearing wastes increased from approximately 4% of the total copper production to 10% by the early 1960's. Projected increases will probably raise this figure to 20 to 30% by the early 1970's. Furthermore, a gradual recognition of the economic feasibility of leaching mined-out areas is evident and will undoubtedly contribute additional production. Waste dumps in canyons and gulches on the periphery of open pit mines, mine stopes, caved areas, and abandoned open pits often contain substantial quantities of leachable rock ranging in concentration from 0.1 to 0.4% copper. Recent developments in the leaching of copper, mainly the recognition of bacterial oxidation of sulfide minerals combined with better under- standing of the control of the salt content of the leach solutions, both by adjusting the pH and/or by hydrolysis, are resulting in a greatly expanded recovery of copper from these hitherto uneconomic mine rejects. 11.5-1. Mechanism of Leaching. Leaching processes for the extraction of metal values from mine ore or waste may be classified for convenience as either chemical leaching or bacterial leaching. Chemical leaching is considered to be the extraction of soluble salts by metathesis in acidic, basic, or neutral water solutions. The reactions involved may be evaluated by chemical thermodynamics. Bacterial leaching, although a chemical process, is dependent on biological catalysis and this is generally a much more complex process. This justifies its separate treatment in the application to leaching. Acid ferric sulfate solutions are commonly employed in the mining industry to leach valuable metals from metal sulfide ores. The leaching mechanism is a reduction-oxidation reaction in which minerals are oxidized at the expense of ferric sulfate. Such chemical leaching is profitable when

Jan 1, 1968

Dr. Rossiter W. Raymond, Past President, Honorary Member, and Secretary Emeritus, died suddenly of heart failure at his home, 123 Henry St., Brooklyn, N. Y., on the evening of Tuesday, Dec. 31, 1918. -He is survived by his' wife and daughter. He was one of the founders of the Institute and its second President, his genius was the Institute's guiding spirit for 47 years. Dr. Raymond was one of the most versatile men of the day; an able mining engineer; brilliant professional writer; an editor of the first rank and an acknowledged authority on matters of literary style; a creator in the fields of fiction, children's stories, poetry and music; for more than 50 years the superintendent of Plymouth Church Sunday School. He will be revered by thousands as a loyal friend, generous giver, and admired colleague. His passing marks an epoch in mining and metallurgical literature. A memorial service will he held in the Auditorium of the-Institute Headquarters on Monday, Feb. 17, 1919, at 4.30 P.M.

Jan 2, 1919

By F. Lynwood Garrison

The future of the Witwatersrand depends upon the possibility of mining and milling profitably the large tonnage of relatively low-grade gold ores known to exist in that area. The problem must be solved if the existence of the gold-mining industry in South Africa is to be saved and continue. To show that this disaster may be avoided, or at least postponed for another decade or longer, the following official statement is of interest: "There is a fairly large area of possible orebody on the East Rand of whose value and depth from the surface we have some though not very accurate knowledge. There is a far larger area south of the Central Rand which probably carries much payable ore, but at depths that at present appear too great to mine. Finally, there is a narrow strip of country over 100 miles in length stretching south from the Rand to Klerksdorp and beyond, which may contain large ore-bodies. The Witwatersrand rocks outcrop over portions of this ground and in places conglomerates occur in it that carry small bodies of payable ore. There is reason to believe that conglomerates of the Witwatersrand system exist over all this strip, though they are for the most part covered by later sediments. It seems probable also that there are large blocks of payable reef in this belt, at any rate in the area that lies close to the present western limit of the developed mines. The structure in this neighborhood is however very complicated and to prove the orebodies will be both difficult and costly." Ores in the Witwatersrand It should be explained in this connection that the conglomerates mentioned here were originally old gravel beds now consolidated into bedded sedimentary rocks, very hard because strongly cemented with secondary silica. The gold exists in this cement and is rarely found in the pebbles composing the rock or bed called locally reef. It is important to realize that these gold deposits are beds; not veins as generally understood by mining engineers and geologists. In addition to these low-grade ore reserves we have also to consider the ore left behind in the old stopes of the upper levels near the surface,

Jan 1, 1931

By G. S. Hume

In Alberta, an oil well with an estimated capacity of 60 to 100 bbl. was "brought in" at Wainwright, the oil being derived from the Colorado group of rocks. In the Norman fields, Mackenzie River area, two new holes completed showed no oil in commercial quantities whereas the "Discovery" well has now an increased flow amounting to about 100 bbl. In Kent Co., Ontario, a well from low down in the Trenton formation gave an initial flow estimated at 200 bbl. This opens up new possibilities for the Ontario fields as this is the first oil from this depth in the Trenton. ACTIVE drilling operations for oil were carried on during the summer of 1923 in various parts of western Canada, particularly in Alberta. During the early part of the summer, interest centered in southern Alberta, in the Coutts area, just north of the producing Kevin-Sunburst field of Montana; but on Nov. 14 a strike of oil by British Petroleums Ltd. at its well near Wainwright, 120 mi. east of Edmonton, diverted public attention to a new field. According to present estimates, this well has a possible production of from 60 to 100 bbl. a day; the oil is 15° Bé. with an asphaltic base and is obtained from a sand at the depth of 2019-2036 ft. The oil stands at 1700 ft. in the casing and there is sufficient gas pressure to cause it to flow when the well is opened. The oil horizon is in a sandstone in rocks of Colorado age. It is known that there is a terrace structure of which the western edge extends in a northwesterly direction from the vicinity of Hardisty to Viking, where it probably swings more to the north. At Viking a small dome-like structure on this terrace gives rise to an important gas field. Wainwright lies directly northeast of Hardisty. The exact structure in the Wainwright field is unknown. At Fabyan, 6 mi. northwest of Wainwright, the Imperial Oil Co.1 last year brought in a large gas well estimated at 14,000,000 cu. ft.; the escaping gas sprayed a small amount of heavy black oil over the derrick. The gas was obtained at a depth of

Jan 2, 1924

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

The Oregon School of Mines Society held its regular monthly meeting on the evening of October 23. This meeting was an informal reunion at which members gave accounts of personal experiences during the last three months. Many members of both junior and senior classes answered their country's call to arms and so did not return to college. The senior class is particularly well represented in the Army, as two men hold lieutenant's commissions and a third is already in France with a hospital unit. The junior class has also contributed men to various branches of the service. Plans for the regular meetings include discussions by members and lectures by outside authorities oil mining and allied topics. These meetings are open to the lower classes and all others interested. The Oregon School of Mines Society, composed of members of the junior and senior classes, has, joined with the sophomore and freshman relining students in purchasing a Liberty Bond under the name of the Miners' Club of 0. A. C. H. W. THOMS, President.

Jan 12, 1917