Search Documents

By Wallace Thorneycroft

This paper by Mr. Thorneycroft, Past President of the Institution of Mining Engineers (Great Britain), and chairman of its Subsidence Committee, is a valuable contribution to the assemblage of data on ground movement and subsidence from coal mining. It deals with the effects of advancing longwall, a method almost universal in Europe but as yet little used in the United States outside of Northern Illinois and in a few scattered places elsewhere in thin coal beds, as in the Lexington field, Missouri. Canon City field, Colorado, and the Birmingham field, Alabama. Although by advancing lougwall, a maximum recovery of coal is obtained and it has to be employed where there are weak shale roofs, especially in deep mines, it is a more expensive method of operation unless the mining conditions are suitable, which is unusual in the United States. On the other hand, there is a growing use in this country of what is essentially retreating longwall, with an approximately straight break-line as described by Rayburn.1 With this method, in which the pillars are substantial, it was shown that the ground movement effect is practically identical with that of advancing longwall, hence the value to mining engineers of the precise data given by Mr. Thorneycroft. His study is unusual in several respects; it deals with conditions connected with the mining of a coal bed 20 in. thick, about 490 ft. below the surface, over a mined-out area in a 5-ft. bed about 90 ft. below, which had been mined about 12 years earlier. Both mines passed under Plean House, a building of massive cut stone construction built over a century ago, in which Mr. Thorneycroft resided throughout the under-mining period. Slight cracks opened in the walls as the longwall face approached the house in mining the upper seam, and closed after the face passed and subsidence took place. In the northwest wall, the last wall the face passed under, some stone blocks were broken, which was attributed to a strike period when the advance of face came nearly to a standstill. Other than this there was no perceptible permanent damage, as indicated by the photographs taken by the undersigned in 1923 (Figs. 1 and 2). Mr. Thorneycroft used a novel means of studying the successive positions of the corners of the building: he hung plumb bobs from the eaves and traced the paths of the respective plumb bob points on level surfaces. The angles made by the house walls with the plumb bob lines gave measures of the slope of the subsidence wave at the respective points. A slight upward wave was indicated by the surveys ahead of the subsidence, which would appear to be due to a tilting over of the massive sandstone stratum in the roof measures near the surface, the edge of the coal face acting as the fulcrum.

Jan 1, 1931

By Wallace Thorneycroft

FOREWORD This paper by Mr. Thorneycroft, Past President of the Institution of Mining Engineers (Great Britain), and chairman of its Subsidence Committee, is a valuable contribution to the assemblage of data on ground movement and subsidence from coal mining. It deals with the effects of advancing longwall, a method almost universal in Europe but as vet little used in the United States outside of Northern Illinois and in a few scattered places elsewhere, in thin coal beds, as in the Lexington field, Missouri, Canon City field, Colorado, and the Birmingham field, Alabama. Although by advancing- longwall, a maximum recovery of coal is obtained and it has to be employed where there are weak shale roofs, especially in deep mines, it is a more expensive method of operation unless the mining conditions are favorable, which is unusual in the United States. On the other hand, there is a growing use in this country of what is essentially retreating long wall, with an approximately straight break-line as described by Rayburn.1 With this method, in which the pillars are substantial, it was shown that the ground movement effect is practically identical with that of advancing longwall, hence the value to mining engineers of the precise data given by Mr. Thorneycroft. His study is unusual in several respects; it deals with conditions connected with ,the mining of a coal bed 20 in. thick, about 490 ft. below the surface, over a mined-out area in a 5-ft. bed about 90 ft. below, which had been mined about 12 years earlier. Both mines passed under Plean House, a building of massive cut stone construction built over a century ago, in which Mr: Thorneycroft resided throughout the under-mining period. Slight cracks opened in the walls as the longwall face approached the house in mining the upper seam, and closed after the face passed and subsidence took place. In the northwest wall, the last wall the face passed under, some stone blocks were broken, which was attributed to a strike period when the advance of face came nearly to a standstill. Other than this there was no perceptible permanent damage, as indicated by the photographs taken by the undersigned in 1923 (Figs. 1 and 2). Mr. Thorneycroft used a novel means of studying the successive positions of the corners of the building: he hung plumb bobs from the eaves and traced the paths of the respective plumb bob points on level surfaces. The angles made by the house walls with the plumb bob lines gave measures of the slope of the subsidence wave at the respective points. A slight upward wave was indicated by the surveys ahead of the subsidence, which would appear to be due to a tilting over of the massive sandstone stratum in the roof measures near the surface, the edge of the subsidence area acting as the fulcrum.

Jan 1, 1931

By M. King Hubbert

DuRing the past summer the writer was asked by the Illinois State Geological Survey to make a study of some of its economic geological problems with regard to the applicability of geophysical methods of prospecting to their solution. The following four problems were suggested for investigation: (1) the fluorspar area of Southern Illinois, (2) oil structures in the south central part of the state, (3) the lead and zinc-bearing area of northwestern Illinois, and (4) the water supply and gravel deposits of the glacial drift. The prime requirements were to find a means of obtaining a maximum of useful information with a fairly modest outlay of expenditure for technical staff and equipment. The method of procedure adopted was that of making a preliminary study of each of the problems named by means of available office data and published reports with supplementary field reconnaissance where necessary. Preliminary Studies Fluorspar.—The fluorspar deposits of southern Illinois as shown by Weller,1 Bastin2 and others are of two main types: (1) vein deposits along steeply dipping normal fault planes, and (2) "blanket" deposits occurring practically horizontally along a certain sedimentary horizon. The vein deposits are composed mostly of calcite and fluorspar in sheetlike veins of thicknesses, where mined, ranging from about 2 to 12 ft. The surrounding topography is in a mature state of development with a relief of about 100 ft. or more. Any geophysical prospecting for this ore would have to depend either upon the physical properties of the ore and associated minerals or upon the properties of the geologic structure containing them. Fluorspar has a density of 3.18, which is somewhat greater than 2.7, that of calcite. Its

Jan 1, 1934

By C. W. Clark, J. H. Schloen

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,1 written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. EARLY SILVER-REFINERY OPERATIONS From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700° F. in a Nichols-Herreshoff furnace, acid¬leached with tankhouse discarded foul electrolyte (20 per cent H2SO4), filtered and charged directly to the doré furnace for refining to doré metal. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1938

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By Henry B. Smith, S. Paul Lindau

ThREe years ago it was decided by the management to granulate the matte that is produced in the smelter of the St. Joseph Lead Co. at Hereulaneum, Mo., thereby doing away with a large amount of labor in handling the matte and in subsequent crushing. On Mar. 1, 1915, the granulator was put in operation and up to Jan. 1, 1916, 18,735 tons had been granulated. The four blast furnaces have a daily output of about 280 tons of pig lead and 100 tons of matte assaying about 11.0 per cent. Pb. It is expected that projected improvements in roasting methods will eliminate more sulphur from the charge, and cut down the matte-fall to about one-half of the present figure. The blast furnaces are tapped into movable forehearths or settlers, 6 ft. by 4 ft. by 22 in., the slag overflowing into 27-cu. ft. slag cars which are hauled to the dump by electric locomotives. Previous to the adoption of granulation, the matte was tapped from the forehearths into small slag pots which were dumped after cooling. The matte cakes were broken with sledges, and transported to the crushing plant for fine crushing and screening. Here the matte was reduced to 1/4-in. size before being fed to the roaster bins. A Wedge and a Holthoff mechanical furnace are used for preroasting before sintering on the Dwight and Lloyd machines. The matte is returned to the furnaces as an iron flux until the gradually accumulating copper content reaches about 7 per cent., after which it is put aside to be concentrated in a small copper blast furnace, the resultant high-grade matte being sold. When the matte does not settle readily from the slag, two settling devices are often used, the second one being a large catch-pot, which gathers any matte that may overflow from the forehearth, the slag then overflowing from the catch-pot into the slag cars. When full of matte, the catch-pot is removed, allowed to cool, and the contents broken and crushed. a With the present plan of granulating, the matte is tapped into 6-cu. ft. iron ladles. These are transported to the granulating plant by a 5-ton

Jan 1, 1917

By A. W. Cochardt

THERE are a number of effects that can cause material damping or internal friction. Some of these are frequency dependent, such as the thermo-elastic effect' and the stress-induced ordering.' Others depend on the amplitude of vibration, i.e., the damping related to the motion of dislocations3 and that due to magneto-mechanical hysteresis.' While many of these effects have been studied, only the magneto-mechanical effect has found extensive practical application. It is the principal source of damping in the current blade material in steam turbines.A magneto-mechanical hysteresis loop is seen in Fig. 1. If an unmagnetized, polycrystalline wire of a material exhibiting magneto-mechanical hysteresis, such as an Fe-14 pct A1 alloy, is twisted in torsion, a relation between shear stress and shear strain y is observed as indicated. The stress-strain curve does not follow Hooke's law -dashed line. Instead, the strain y increases nonlinearly and partly irreversibly, due to the motion of ferromagnetic domain walls,* until a critical stress is reached, which in this case is about 3,500 psi. If the applied stress is raised further, the strain appears to increase linearly and reversibly in accordance with Hooke's law, since all domains are now aligned in easy directions of magnetization nearest to the direction of the applied stress, and plastic flow has not yet started noticeably. On removing the applied stress, a remanent shear strain y, is observed, which is related to the irreversible magnetostriction of the material.' The energy dissipated in the material during a stress-strain cycle is proportional to the critical stress t, and the remanent magnetostrictive shear strain 7,. The purpose of this investigation was to make a survey of the magneto-mechanical damping of ferro-

Jan 1, 1957

By John R. Gould

A mathematical treatment of multiple-pass floating-zone refining of semiconductors, including the evaporation of solutes from the melt at reduced pressure, is presented. Vapor pressures and evaporation rate constants for phosphorus, arsenic, and antimony in germanium have been determined from floating-zone experiments conducted at 10 mm Hg. Rate sensi-tivity of arsenic in germanium has been examined over the range of 1 to 10 in. per hr growth rate. The equilibrium value of the segregation coefficient of arsenic in germanium, as determined by an extrapolation of these data, was found to be 0.09. PFANN has treated the segregation of nonvolatile solutes in the zone-melting process, Bradshaw and Mlavsky2 considered the evaporation of solutes in a vacuum during the growth of crystals by pulling from the melt, and van den Boomgaard3 has shown that it is possible to bring a volatile impurity element homogeneously into an ingot by means of zone-melting under a constant pressure of that element. This paper is concerned with the volatilization of solutes during zone - melting in a vacuum. The mathematical analysis by Lord4 of multiple-pass zone melting is extended to include evaporation of solutes. A method is presented in which evaluations of vapor pressures, evaporation rate constants, and distribution coefficients may be derived from the variation of solute concentration in the floating-zone refining of germanium at 105 mm Hg. EXPERIMENTAL Ingots of zone refined germanium, approximately 1/4 in. in diam and 10 to 12 in. in length, were subjected to several floating-zone passes at 105 mm Hg in order to provide intrinsic material for these studies. These ingots were then seeded in a [Ill] direction and solid-doped to a constant impurity concentration of approximately 1015 atoms per cmS in a forming gas ambient (10 pct H - 90 pct A) at 1/2 atm gage. The resulting crystals were subjected to repeated floating-zone passes at 105 mm Hg and a concentration profile along the length made after termination of each pass. Concentrations were determined from four-point probe resistivity measurements, and proper precautions were taken to prevent contamination during handling. A constant zone length, crystal cross section, and growth rate were maintained during zoning. A stationary coil and moving crystal system were employed for floating-zone growth with neither the section of crystal above nor below the melt rotated.

Jan 1, 1962

By R. A. Flinn, John T. Norton

A CONSIDERABLE number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping. capacity," might be a useful indicator of structural. changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction os mechanical hysteresis occupies such a position, and, although it is nor well understood in terms of basic metallic theory, an observation of itt changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention: The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail.

Jan 1, 1938

By R. A. Jr. Flinn

A CONSIDERABLE number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observa-tion of this property, which often is referred to as "clamping capacity," might he a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observa-ble. Even if the observed phenomenon cannot be explained in funda-mental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail.

Jan 1, 1938

By K. D. Jacob, H. L. Marshall, D. S. Reynolds

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

By D. S. Reynolds, K. D. Jacob, H. L. Marshall

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

By Charles L. Bauer

WHEN a single crystal is annealed following plastic deformation recrystallization usually occurs rather than polygonization. Consequently, re-crystallization has received the overwhelming amount of attention albeit the intrinsic mechanisms by which dislocations rearrange and annihilate one another are just as well revealed by crystal polygonization. It is the purpose of this note to demonstrate the usefulness of studying the polygonization process by means of an etch-pit technique in sodium chloride. Sodium chloride deforms easily (the slip system is of the [110], (110) type), readily cleaves on (100) planes, and can be chemically etched so as to reveal the intersection of dislocations with a free surface. Thus it is possible to observe the distribution of dislocations after a crystal has undergone a specific deformation and annealing cycle. Various phases of the polygonization process

Jan 1, 1965

David H. Browne was born June 8, 1864; at Hollymount, County Mayo, Ireland. At the age of 16, after going through the Londonderry Academy; he came to this country, and entered the University of Michigan, where he was graduated in 1885. He began his scientific practice as chemist, under F. A. Emmerton, in the laboratory of the Joliet Steel Co., after which he served some time as chemist at the Ludington mine, Iron Mountain, Mich. But in 1888 he went back for a year to his alma mater as instructor in inorganic analysis. Those who knew him feel sure that he would have been an efficient and popular professor; but his ardent temperament could not brook the rnonotony and confinement of the class- room; and in 1899 he went to work at the Andrews and Hitchcock blast-furnaces, at Hubbard, Ohio, where he remained until 1891, when he entered as chemist the service of the newly organized Canadian Copper Co., operating in the Sudbury district, Canada. This was the beginning of his special professional life-work. For twenty-six years he devoted himself to the numerous and complex problems successively arising in connection with the metallurgical treatment of the nickel-copper ores of Sudbury. One of his notable achievements was the development of an electro-lytic process for the separation of nickel and copper in the ores referred to. This method was successfully employed for several years; but when the Canadian Copper Co. was absorbed by the International Nickel Co., the cheaper Orford process owned by the latter was substituted. . A still more permanently important piece of metallurgical progress credited to Mr. Browne was the successful firing of reverberatory smelting-furnaces with powdered coal-a measure which had been desired, dreamed and attempted by others, but which he was acknowledged as first to put in practice on a large scale. The Engineering and Mining Journal of April 7, 1917, says editorially of this improvement:

Jan 6, 1917

By H. B. Menardi

THE history, geology, ore deposits and current mining operations of the Huitzuco district have been described by C. W. Vaupell1 and the current mill operations by David Segura.2 This paper completes the story of Huitzuco with a description of the reduction of the flotation concentrates. The predominant ore mineral in the Huitzuco deposit is livingstonite, a rare, mercury-antimony sulphide (HgS.2Sb2S3). Other associated minerals include cinnabar, stibnite and elemental sulphur. The gangue is largely limestone and gypsum. Former operators mined a selected grade of ore, from which the mercury was recovered by an expensive, inefficient operation. A consid-erable tonnage of rejects and fills, carrying mercury and antimony, was left in the mine. In order to recover both mercury and antimony from these fills and also from newly developed ore, a combination method has been developed, by means of which the livingstonite is concentrated by flotation and the flotation concentrates subsequently reduced to metallic mercury and antimony. An essential part of the flotation treatment, as developed by Segura, is the use of copper sulphate as an activating agent. A typical analysis of concentrates now being produced at the property is as follows: Hg, 7.73 per cent; Sb, 26.40; Fe, 1.20; S, 29.68; CaO, 11.50; MgO, 7.25; Si02, 1.63; A1203, 0.65.

Jan 1, 1939

GENERAL GEOLOGIC DESCRIPTION The Escalante silver deposit located in southwestern Utah is an epithermal vein system consisting of a hanging wall and footwall vein, straight along strike and dipping about 1.2 rad (70°). The veins consist of banded quartz and calcite fissure fillings between volcanic wall rock that are silicified for some distance outward from the vein. The walls of the veins are sharp and the silver values are irratically distributed through the various bands within the vein. Only very low grade values are to be found in the wall rock on either side. The portion of the veins above the water table have been somewhat leached, with some secondary enrichment below. The mineralogical zonation is variable due to a fluctuating water table through geologic time. SAMPLE MANAGEMENT AND COMPOSITE ASSAYS Sample data for the deposit was obtained from over 50 diamond drill holes, from channel samples cut at intervals across a drift, and from scattered surface trenches along the out- crop of the hanging wall vein. Fig. 13-1 is a surface plan map showing the vein outcrop and some diamond drill locations. Two cross sections through the vein are shown in Figs. 1 3-2 and 13-3. Nearly all of the diamond drill core of vein material was assayed in 0.3-m (I-ft) lengths, from which weighted composite assays were manually calculated for the horizontal thickness of the vein. The centers of the composited samples were plotted in north and east coordinates and by elevation, and locations and assay

Jan 1, 1980

By G. Broughton

For the past few years a great amount of work has been done on the viscosity characteristics and gelation of clay suspensions, much of which has been reported in papers published by the Institute.7,12,18,19,24 Impor-tant reviews have been made elsewhere by Evans and Reid,10 Marshall20 and Clews, Macey and Rigby,8 the last two on the general properties of clay. It is unnecessary, therefore, to recapitulate past work beyond recalling that three explanations for the high viscosity and gelation of clay suspensions have been put forward. For lack of more exact nomencla-ture, these may be called the water hull,16 mechanical interference" and attraction-repulsion" theories. The first pictures the clay particles as surrounded by relatively rigid water envelopes, which increase effective volume; the second emphasizes the mechanical interference of platy particles or their agglomerates; while in the third the particles are assumed to be held relatively rigidly at a distance from each other determined by the balance between the attractive (van der Waal's) forces and the elec-trical repulsions of the charges. 13,14 This article presents fresh data on clay suspensions, particularly on the influence of previous flow history of the suspensions, specific contra-ions, temperature, solvation and particle size, in an attempt to contribute to the solution of the problem.

Jan 1, 1938

On Friday, Jan. 17, the thirteenth impression of the Perkin Medal was presented to Dr. Frederick Gardner Cottrell, at a meeting of the New York Section of the Society of Chemical Industry, held at the Chemists' Club, in New York City. The presentation address was delivered by Dr. C. F. Chandler, Senior Past President of the Society. The medal was awarded for the recipient's work in the electrical precipitation of suspended particles in gases. Dr. Cottrell's career, which is so familiar to members of the Institute, was sketched by Dr. Chandler. He told at some length of the experiments leading up to the final solution of electrostatic precipitation, which has done so much to solve the problem of smelter smoke. The principal interest in Dr. Cottrell's speech of acceptance lay in his remarks about helium, the production of which has been so reduced in cost that it has practically supplanted the use of hydrogen for inflation purposes in war balloons. He said: "Two or three weeks after war was declared in 1917, Dr. R. B. Moore attended a meeting of the American Chemical Society in Kansas City. At the general session, Mr. Seibel of the University of Kansas, gave a paper on krypton and xenon in some of the natural gases of Kansas. At the end of his paper, he expressed regret that at such a time, when everyone was thinking of war problems, his paper was of a purely scientific nature and had no practical bearing on the war. Dr. Moore immediately got up and said that he did not agree with Mr. Seibel. The presence of helium in those wells could, and should, have a very practical bearing on the war, as this gas could be extracted in quantity from the natural gas and used for balloons and Zeppelins. He pointed out some of the natural advantages of helium over hydrogen, and quoted Sir William Ramsey's letter advocating the use of helium for airships. The general attitude of those present was one of scepticism, so he finally asked Dr. Cady for his opinion who stated that he believed-the thing could be done, but was very doubtful whether it could ever be made practical on account of the cost." Dr. Moore in a letter wrote: "That same day I talked to Dr. Parsons, who was present at the meeting and was returning to Washington almost immediately. I told him what had happened, and that I believed the matter should be taken up by the Bureau at once and presented to the War Department. He promised to do this as soon as he got to Washington; and I know that he did take the matter up with other Bureau officials." Dr. Cottrell continued in part: News of Ramsey's suggestions also reached this .country through other channels and eventually came to our attention. Professors Satterly and Patterson of the University of Toronto commenced experimentation of the subject Jan. 1, 1916. Col. G. A. Burrell, who headed the research department of the Gas Warfare Service at the American University, tells me that Cady's experiments had also suggested similar possibilities to him.

Jan 3, 1919

By C. S. Roberts, S. L. Couling

PLASTIC strain in polycrystalline metal as a result of bulk movement of one grain with respect to another along grain boundaries is not new. Rosenhain and Humphrey observed such effects shortly after the turn of the century.' Since then, observations of grain boundary deformation have been made on several metals. In recent years, intensive studies of the deformation at grain boundaries have been performed on polycrystalline metal and bicrystals.14-20 Aluminum or its alloys have been used in these latter studies. The subjects of controversy at present appear to be not whether grain boundary deformation exists, but 1) how quantitatively important it can be in polycrystalline metal, and 2) what its detailed mechanism is. Some investigators have concluded that such de- formation is minor in importance while others have concluded that it is a major consideration. Some have concluded that it involves shear of one grain over another at the interface while others have concluded that it operates by crystallographic deformation within the grains near ,the boundary. A categorical statement for electrolytic magnesium cannot be made on either of -these points. When polycrystalline magnesium is deformed in creep under conditions of high strain rate and low temperature, grain boundary deformation is relatively slight." Under these conditions, much deformation occurs within the grains and boundary contours change to a higher-energy jagged form. The result is shown in Fig. 1, where boundary jaggedness is pronounced upon polishing and etching after a plastic strain of approximately 6 .pct at 300°F and 3000 psi. No migration of the boundaries has been detected in this process. When the same metal is deformed the same amount at 600°F and 300 psi, resulting in a much lower strain rate, the boundaries migrate toward a lower energy configuration, where

Jan 1, 1958