Search Documents

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By Elwood G. Haney, R. N. Parkins

Stress corrosion cracking of two heats of 18 pct Ni maraging steel in rod form immersed in an aqueous solution of 0.6N NaCl at pH 2.2 has been studied on un-notched specimens stressed in a hard tensilf machite. Austenitizing temperature in the range 1830 to 1400 F has been shown to have a marked influence on the propensity to crack, the loulest austenitizing- temperature producing the greatest resistance to failure. In the nzosl susceptible conditions, the cracks followed the original austenile grain boundaries; but when tlze steels zcere heal treated to inproze their resistance to stress corrosion, the cracks becatne appreciably less branched and slzouqed significant tendencies to become trans granular. Electron metallography of the steels indicated the presence of snzall particles, possibly of titanium carbide, along- the prior austenite grain boundaries and these particles u:ere more readily detectable in the structures that were most susceptible to cracking. Crack propagation rates, which appeared to be dependent upon applied stress and structure, were usually in tlze reg-ion of 0.5 mm per hr and may, therefore, be e.xplained on tlze basis of a purely electrochetnical ,nechanism. However, there is some ezliderzce from fractography that crack extension may be assisted by ttlechanical processes. Anodic stit)zulation reduced the tiwe to fracture, although cathodic currents of small magnitudes delayed cracking-; further increase in cathodic current resulted in a sharp drop i,n fracture litne, possibly due to the onset of hydrogen ewbrittlement. THE use of the high strength maraging steels, with their attractive fracture toughness characteristics, is restricted because of their susceptibility to stress corrosion cracking in chloride solutions. Although this limitation has resulted in investigations of the stress corrosion susceptibilities of these steels, there have been few systematic studies aimed at defining the various parameters that determine the level of susceptibility. It is the case that the usual tests have been performed with the object of defining some stress or time limit, on unnotched or precracked specimens, within which failure was not observed,' but while such results may be of some use in design considerations, they are necessarily concerned only with the steels as they currently exist and not with their improvement to render them more resistant to stress corrosion failure. This omission may be considered unfortunate because the indications are that stress corrosion in maraging steels shows dependence on structure in following an intergranular path, and since experience with other systems of intergranular stress corrosion crack- ing is that susceptibility may be varied by modifying heat treatments, a similar effect may be expected with maraging steels. It is sometimes from such observations that a fuller understanding of the mechanism of stress corrosion crack propagation begins to emerge, leading in time to the development of more resistant grades of material. The present work was undertaken to study only one aspect of the influence of heat treatment upon the cracking propensities of the 18 pct Ni maraging steel, namely the effect of austenitizing temperature, although certain ancillary measurements and experiments have been undertaken. EXPERIMENTAL TECHNIQUES Most of the measurements were made on a steel, A, having the analysis shown below, although a few results were obtained on a steel, B, having a slightly different composition. Both steels were supplied in the austenitized condition, A as 3/8-in-diam rod and B as 1/2-in.-diam rod. Cylindrical tensile test pieces were machined from the rods: the overal length was 2 1/2 in., the gage length 1 in. and the diameter 0.128 to 0.136 in. The stress corrosion tests were carried out with the specimens strained in tension in a hard beam testing machine, the necessary total strain being applied to the specimen over a period of about 30 sec, after which the moving crosshead was locked in position and the load allowed to relax as crack propagation proceeded; the load relaxation was recorded. The load was applied after the specimen had been brought into contact with the corrosive solution, the latter being contained in a polyethylene dish having a central hole through which the specimen passed, leakage being prevented by the application of a film of rubber cement. The specimen was in contact with the solution for over half of its gage length and the solution was exposed to the air during testing. The solution was prepared from distilled and deionized water to which NaCl was added, 0.6N, and the pH adjusted to 2.2 by HCl additions. The composition of the solution

Jan 1, 1969

By R. A. Davidson, L. Silverman

RESIDENTS of many urban centers are becoming increasingly aware of the obscuring effect of fume and smoke discharge from power, metallurgical, chemical, and other industries; and they, as well as the legislatures of these affected cities, are agitating for cleaner air. Management's most pressing problem is to find an economical way to reduce process effluents in response to the growing pressure from population and legislative demands. The removal must be done, if possible, without handicap to the current operation, since the costs of relocating are often excessive or prohibitive. In fume recovery or disposal, an important item to consider is whether or not the material being discharged has any value. If it has commercial value, the cost of its recovery may offset or aid amortization. For this reason, in making a study of the specific problem in hand, a major factor was the nature of the material emanating from the stack: in particular, its particle size, size range, and its chemical and physical composition, as well as its potential value and utility when recovered (in either a wet or dry state). Should the product have no commercial value, it must be disposed of at minimum cost in a way to prevent recontamination. Initial studies were therefore made to determine stack concentrations and volumes of material evolved from the operations. The next phase of the study concerned the physical and chemical nature of the collected fume. The third portion of this paper describes the wet and dry collector studies undertaken to recover the fume. Cleaning Requirements for Ferroalloy Furnace Operation The basic need for any effluent collection equipment is the highest possible efficiency and the lowest tolerable resistance when the power consumption involved is considered. Since the electric furnace effluent is largely composed of fume of small size (less than 0.5u), it has high light obscuring properties, and even low concentrations will cause some loss of visibility and be evident to nearby residents. The permissible limit for fly ash emission in many cities is based on a weight value (viz, approximately 0.4 grains per cu ft), but the smoke density values are dependent upon a shade of color. In the case of the Los Angeles County code, emission is restricted to pounds per pound of material processed per hour basis (but not exceeding 40 lb per hr for any one given plant operation). If an average particle size of the fume from ferro-silicon alloy electric furnaces is assumed to be 0.4u (as shown later, this is the approximate mean size) and an average loading of 1 grain per cu ft (stp), each cubic foot of stack gas will contain approximately 75x10 10 particles (based on assumed, and confirmed, spherical shape and a standard deviation of unity). When it is realized that the air in metropolitan areas, which are also general industrial areas, contains approximately 5x108 particles, the tremendous light scattering effect of this concentration becomes apparent. Consequently, nearly 100 pct collection would be necessary to equal the average concentration. Fortunately, however, discharge from a high point above ground (50 to 100 ft) will result in at least a thousandfold dilution, or the stack concentration reaching the ground in the foregoing case might result in a ground concentration of ' particles. If the concentration at the source could be reduced by a factor of 100 (99 pct efficiency of collection), then a concentration of 75x10" particles would be diluted to 7.5x10' which would be very satisfactory. An efficiency of 90 pct (factor of 10 decontamination) at the source would result in a discharge of 75x109 articles which upon dilution yields 75x10 which is still 15 times the general air value. Another approach to this consideration is to use the value of concentration of 0.005 grains per cu ft for the value of a visible effluent as cited by Kayse.1 To attain this value with an average loading of 1 grain per cu ft would require an efficiency of 99.5 pct. Since the foregoing value is not based on any reported size of fume particles, it is felt that the numbers' approach given previously is more reliable. These calculations serve to indicate the desirability of thorough cleaning, preferably at the source, and with efficiencies well above 90 pct, preferably above 95 pct (dilution 1:20). One of the most important items in any control program is to reduce the concentrations as close to their sources as possible. The use of better furnace design, deeper coverage over the electrodes, and the prevention of blows or breaks in the surface all help to reduce dissemination; consequently, all of these improvements should be made, if possible, to cut down the effluent load. In addition, in order to minimize the volume of contaminated air that has to be cleaned, the furnace should be enclosed as much as possible. Test Arrangements Before fundamental studies with collectors were made, a furnace stack selected for the test program was sampled to determine the gas temperatures and

Jan 1, 1956

By George A. Hill

WE of the oil industry, devoted to freedom of initiative, free competitive enter- prise, and free American institutions, applaud, with one voice, affirmation by the President of the national will and purpose to preserve and to protect, against all aggressors, "our American way of life with our individual and national freedom." We subscribe utterly and completely to this guiding declaration and seek its further definition as applied to the oil industry. Fortunately for all, the policy of the Government, after adequate study and deliberation, has been given precise definition. The National Defense Advisory Commission, with its patriotic, highly qualified, and distinguished personnel, has unanimously agreed to and adopted twelve general principles governing national defense contracts and also fair labor standard requirements. The President of the

Jan 1, 1940

By David Cole

AT the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that timè impending. The simplified flowsheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.1 The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopyrite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were, properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) . the very fine sand, and especially the very fine but still granular sulphide particle's, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrass-ment, the increase of capacity required.

Jan 9, 1916

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1) dump leaching, where the ore is moved from its original location to be leached at another site; and 2) In-situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains. Whichever leaching method is used, it is almost always necessary to break up the ore before leaching. In this paper a study is reported which indicates that rock broken by an explosion-in particular, an underground nuclear explosion-is significantly more amenable to leaching then is rock broken by other methods. These results suggest that the leaching speed and efficiency could be increased by nuclear fracturing of the ore. Not only would the leach time be shortened, but the resulting increase in strength or richness of the solutions would decrease plant installation expense as well as reduce pumping and processing costs. A considerable fund of experience has been accumulated in the course of several hundred experimental underground nuclear explosions, so that the gross results of any given nuclear explosion can now be predicted with a fair degree of confidence.' From this knowledge it seems clear that, under the proper conditions, large ore bodies can be fractured much more economically-macroscopically speaking-by nuclear explosions than by other methods. The present study concentrates on smaller scale effects that is, the cracks in the chunks of rock broken by the explosion-and shows that here too, in the microscopic domain, there are important advantages to nuclear fracturing. The intense shock produced by the very fast acting, high-brisance nuclear explosive fractures the rock in a way that should significantly improve its leachability. Experimental Procedure This study compared rocks broken by nuclear explosives with rocks produced by conventional mining, quarrying, or core drilling. The test samples, granite chunks 6 to 8 in. on a side, plus core sections, came from the area of the Hardhat*2 nuclear explosion and were taken both before and after the explosion. For comparison, several samples of quarried granite were obtained from a local gravestone monument company. The general procedure was to soak the test samples in leaching solution and then determine the extent of penetration. A standard commercial copper leaching solution was used (10 gpl Cu, 10 gpl H2SO4, 5 gpl ferric Fe, 15 gpl total Fe, pH about 1.5), to which a water-soluble penetrant dye, Zyglo 1-c, had been added. Details of the procedure were as follows: 1) Sample leached in solution containing Zyglo penetrant dye. 2) Washed with water. 3) Air-dried. 4) Cut with granite wire saw. 5) One face polished with granite monument polish. 6) Sent directly to be photographed, or heated at 110°C for 2 hr and then sent to be photographed. 7) Photographed under ultraviolet light to show crack patterns. Results After 10 days of leaching at 70-75°F, the samples were removed from the solution, washed, dried, and cut in half with a granite wire saw to study the penetration of the leach solution. Since the Zyglo dye in the leach is visible under ultraviolet light, the degree of penetration of the leach (and hence the cracks in the samples) can be studied on photographs of the crosscut samples made under ultraviolet light. The photos in [Fig. 1] show how the leach solution penetrated various representative samples. Of the 71 rock samples examined, fractures were most frequent and prominent in samples from the rubble produced by the nuclear explosion [(Fig. 1D)]. Fracturing was less apparent in shaft-mined rock [(Fig. 1B)], still less evident in drift-mined rock [(Fig. 1C)], and practically nonexistent in cored or quarried specimens [(Fig. 1A)]. The samples in [Fig. lA-C] were from the same general area as the nuclear explosion, but they were obtained before the explosion. Results of the crack studies are summarized in [Table 1]. The Zyglo-treated leach solution penetrated the test samples at the rate of about 1/2 mm during the first hour, 1 mm by the end of 4 hr, 2 to 3 mm in 12 hr, and 4 to 6 mm in 10 days, showing a progressively slower rate with time.

Jan 1, 1972

By B. W. Frazier

IN the numbers of the Engineering and Mining Journal of June 27th and July 11th, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced to the same standard of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given -by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of the pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part of the furnace, by the dissocia¬tion of carbonic oxide, is again converted into carbonic oxide or

Jan 1, 1875

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

By Morris A. Steinberg

Because of the broad scope of my topic I will discuss my subject from the point of view of a present status of the metallic materials that are used in structures and will dwell primarily on those structures related to high- performance aerospace systems. Thus, I can best portray the status of these structural materials as related to existing transportation systems, delineating some of the highlights of alloy development, fabrication, and properties obtained. I shall point out what are, in my opinion, the needed solutions to pressing unsolved metallurgical problems connected with certain selected metals: aluminum alloys, beryllium, titanium, steels, superalloys, refractory metals and some metal-matrix composites. Aluminum Alloys For a number of years a series of strong aluminum alloys used for airframes has had an important bearing on the development of minimum- weight, highly efficient structures. Among these alloys are such familiar ones as 2024-T3, 2014-T6, 7075-T6, 7079-T6 and 7178-T6. A review of the development and use of strong aluminum alloys in aircraft structures indicates that before about 25 years ago there was very little application of products other than forgings in the high-strength tempers produced by precipitation heat treating to T6- or T8-type tempers. 1 As stated by Dix in 1944, "There has been a gradual evolution in engineering viewpoint regarding the mechanical characteristics which are required in a structural material suitable for aircraft. Formerly, emphasis was placed on a generous spread between yield and tensile strengths, on elongation, on impact strength and on resistance to corrosion. Aircraft structural engineers still differ widely as to the importance which they attach to these proper tie.” 2 It is fair to say that this evolution is still taking place, that the problem is much the same in 1970 as in 1944 - except that strength levels have advanced some - and the question remains as to how far we can go in that direction. In the meantime, a new group of alloys has received acceptance and widespread use. The first alloy of this group, 7075-T6, was formally introduced by Dix's 1944 paper. The drastic changes that have taken place in the size and configuration of components employed in air-

Jan 1, 1971

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By J. P. BONARDI, William F. Boericke

BOULDER COUNTY, Colorado, ranked during the war years and until the end of 1918 as one of the foremost tungsten-producing districts of the world. In 1919 production fell off drastically, due to heavy importations of foreign ores from China, Burma and South America. So large were the imports that even after the enactment of a protective tariff in 1922 of 45c. per lb. on tungsten metal, equivalent to $7.14 per unit (201b.) of tungstic acid? (WO,), the stocks of metal in this country were extensive enough to supply the demands of industry, and prevent general resumption of mining by domestic producers. Even today there are only two producers in the Boulder district though at one time as many as twenty separate companies were in operation. About the same ratio holds for other tungsten-producing districts in the country, including California and Nevada. Total consumption of tungsten concentrate in terms of 60 per cent WO2 in the United States amounted to approximately 3790 tons in 1928, according to Frank L. Hess.' Of this amount, domestic mines contributed 1290 tons, and the rest, 2500 tons, was imported. Yet in 1917, with tungsten concentrate selling at $20 per unit, the Boulder district alone produced 2707 tons, indicating the effect of enhanced ore price upon production. It is believed by American tungsten miners that, given a sufficiently high tariff, all the demands of industry can be met by domestic production without placing a prohibitive burden on consumers. For instance, in steel manufacturing the percentage of tungsten entering into the manufacture is so small that, ?regardless of cost, it can constitute but a small fraction of the cost of steel to the buyer.

Jan 1, 1929

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

R. H. SWEETSER, Columbus, Ohio.-My experience with oxygen in the blast is limited to the use of one tank of oxygen in melting out a chilled anthracite furnace. The oxygen was introduced through the peephole of the tuyeres and opened them in a very short time. We could see that an intense heat was generated just as soon as the oxygen struck the fuel. I agree with the committee in respect to many. of the things that will probably happen in the iron blast furnace, particularly as to the speeding up of the operation. There will undoubtedly be changes in the shape of the blast furnace, and if I were designing one today I should hesitate about the form to give it. Mr. Kirby suggested that the proper shape might be rectangular. Some of the men of the American Rolling Mill Co. have reached the same conclusion, as a result of Royster and Joseph finding that the combustion zone in the front of the tuyeres extended into the furnace less than 40 in. If this is correct, we might build the furnace with an elongated rectangu-ular hearth having the shorter dimension a little over 80 in. and secure. a very intense temperature in the hearth. The committee's report said, "With more oxygen available in the blast, the smelting ability of the furnace will be increased beyond the' speed of the preparing zone in the shaft." This can be controlled by providing ample facilities for getting stock into the furnace, and this will be one of the biggest changes in blast-furnace construction. The question has been raised as to finding suitable refractories to withstand the increase of hearth temperature. If the furnace can be kept full, the descending column of cold material will probably take care of the increased heat from more rapid combustion of the coke. At the Cleveland meeting, in 1912, the iron blast-furnace men listened with great interest to a paper on copper slags; from Mr. Kirby's paper, it looks as though they might again have to go to the copper men, for many of the problems of the iron blast furnace of the. future that uses oxygen may be worked out on lines of the copper blast furnace.

Jan 11, 1924

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

Mr. A. Bement, Chicago, Ill. (communication to the Secretary*) :—Mr. Campbell, in proposing his method of sampling coal-seams, has rendered an important service in insisting on the presentation of an adequate history of the sample; and it is to be hoped that his suggestion will meet with further recommendation. In my opinion it is fully as important that a complete description of the sample and the conditions surrounding its taking be given, as the results of the analysis itself; and if such should become standard practice, coal-analysis would assume greater value. As it is, the published data are very confusing, and only to an extremely small extent are they really useful. The method suggested by Mr. Campbell, however, cannot have a general application; for example, in the Eastern Interior coal-basin, particularly at the present time, the output consists largely in grades other than mine-run, which in Illinois, for the year 1905, was only about 24 per cent. of the total product; and inasmuch as Mr. Campbell's method of sampling cannot give values for any other grade than mine-run, my contention that, at best, it can have but a limited application, is apparent. To illustrate the argument, there are two coal-seams, with the characteristics of which I am particularly familiar; each seam, as it lies in the ground, contains almost exactly 10 per cent. of ash; the lump coal from one of these seams ranges from 10 to 11 per cent. of ash, but from the other seam it does not average more than 6 per cent., although, as before mentioned, the average percentage of ash in the full seam is the same for each case. A careful and proper sampling of coal-seams, to be followed by analyeis, is to be commended in connection with all investigation; in fact, it should precede any careful study. A serious error, however, may be made in attempting to use such results to set values on the product as shipped or received. The only

Jan 1, 1906

By K. D. Jacob

MONTANA Phosphate Produucts Co., a subsidiary of The Consolidated Mining and Smelting Co. of Canada Ltd., operates three properties near Garrison, Mont., known as the Anderson, Graveley, and Luke mines. All three are underground operations, mining the same narrow bed at points several miles apart. The Anderson, the oldest and largest of the three, has produced about 700,000 long tons since 1929. The Graveley has produced slightly over 100,000 long tons since 1940, and the Luke, acquired in 1943, is still in an early stage of development. The great bulk of the output has been shipped to the Trail, B. C., plant of Consolidated Mining and Smelting Co. for use in the manufacture of fertilizers. The phosphate seam is the basal member of the Permian Phosphoria formation. In all three mines it has a uniform thickness of 3 to 4 ft. of oulitic phosphate, with a few shaly partings. The overlying part of the formation comprises about 50 ft. of chert and the immediate footwall consists of a few feet of shale and sandstone. underlain by the Quadrant quartzite.

Jan 1, 1944

By John Cogan

INTRODUCTION Lake tapping is a method of blasting an intake into a body of water from below the natural water surface without first lowering that surface or installing a protective cofferdam around the tap hole. Lake taps are done by first excavating a tunnel almost to the water/rock contact and then blasting out the final protective rock plug at one time to allow water to suddenly inflow into the tunnel from the lake. This procedure can be done "dry" or "wet." In the dry method the tunnel is empty of water before the final plug blast while in the wet method it is partially filled with water. This paper describes a wet method lake tap as performed at Alaska Power Authority's Tyee Lake Hydroeletric Project in southeast Alaska. The Tyee Lake project is located approximately 40 miles southeast of Wrangell, Alaska, in a glacially formed valley called the Bradfield Canal. The project consists of a powerhouse located at sea level on the canal, a system of tunnels and shafts connecting the powerhouse to Tyee Lake at elevation 373 m (1225 ft), and an 129 km (80-mile) electrical transmission line leading from the powerhouse to Wrangell and then Petersburg, Alaska. Tyee Lake itself is a natural lake gouged out of the rock by glacial ice during the last ice age. The objective of the project was to tap into the lake and use the water as a source for power production. The techniques used for lake taps have been developed in Norway where conditions are favorable for their use in hydroelectric proj¬ects. Over 100 have been performed. In the United States the Tyee

Jan 1, 1984

By H. R. Stahl

The disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat; is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. Dry Crushing The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 23/4 tons to 81/4 tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943

By H. R. Stahl

The disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat; is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. Dry Crushing The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 23/4 tons to 81/4 tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943