Search Documents

By M. W. Bartley, Hugh M. Roberts

SUBSTANTIAL deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper part of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconformable, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series. The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement.

Jan 1, 1943

By Keith T. Griffiths

INTRODUCTION The Empress Nickel Mine is situated forty-eight kilometres west of Kadoma in the Zhombe Communal Land of Zimbabwe. The mine came into operation in late 1968 based on a proved and probable ore reserve of twenty million tonnes. The initial production rate was 55 000 tonnes per month from underground. This was boosted to 85 000 tonnes per month in mid 1970 when the opencast operation came into production. The mining method at Empress is sub-level open stoping with main haulages mined at ninety metre intervals and sub-levels at eighteen metres. The extremely wide ore body of up to one hundred metres in width has necessitated leaving extremely large rib pillars and sill pillars in position to maintain mine stability and to act as regional support of the hanging wall. In early 1976 the opencast operation had reached its final economic depth and it was then necessary to increase underground production to 85 000 tonnes per month. Since a large portion of the ore reserve remained in both rib and sill pillars, it was necessary to embark on a positive pillar recovery programme. For this reason it was decided to introduce a sandfilling programme for the mined-out stopes and a modified system of sub-level open stoping with post filling of the lower stopes. ORE BODY GEOLOGY AND GEOMETRY The Empress orebody outcrop has a strike length of nine hundred and fifty metres on a north west - south east axis. It is a steeply dipping (65' - 75') tabular orebody of gabbroic rock which has been extensively altered. The north west - south east strike length of nine hundred and fifty metres on surface reduces to some two hundred

Jan 1, 1983

By AIME AIME

THE Fall Meetings of the Institute of Metals Division and of the Iron and Steel Division were held in Cleveland from Tuesday, Oct. 20, to Thursday, Oct. 22, as a part of the National Metal Congress. The registration at the technical sessions was something over 450 and the attendance at the joint dinner of the two Divisions on Wednesday evening taxed the capacity of the dining room. The president of the British Institute of Metals, W. R. Barclay, consulting metallurgist to the Mond Nickel Co., Ltd.; of London, was in attendance at several of the technical sessions and was one of the after-dinner speakers at the banquet. He commented on the desirability of greater international amity and cooperation in these troubled times and of the role that technical societies, such as the A. I. M. E. and his own British Institute of Metals, can and indeed are playing in bringing this to pass, with their membership and contacts reaching to all parts of the world. He also referred to the new reciprocal membership arrangements in effect between the A.I.M.E. and the British Institute of Metals.

Jan 1, 1936

By Gerald Edmunds, M. L. Fuller

The development of "fiber" or preferred orientations, during the plastic deformation of metals, and the relation of such structures to the anisotropic characteristics of worked metals has become a subject of common knowledge among metallurgists. Very little has been published, however, relative to variations existent throughout the cross-sections of rolled strips,1 and the influence that such variations may have. This paper presents such a study on a rolled zinc alloy.2 The significance of small differences in surface structure is shown in relation to bending properties. Experience with zinc and its alloys has shown that the outer radius of the bend, which is subject to tensile deformation, is the common region of failure. In considering relations of structural characteristics to bending properties it will suffice, therefore, to consider the ease and possible extent of tensile deformation resulting from various orientations. It is necessary in this connection to assume that on the average the individual crystals of a polycrystalline material act substantially as if their movements were unobstructed by the surrounding grains. This assumption is not strictly valid, but the error involved is unlikely to affect seriously the qualitative conclusions derived from its use. The mechanism of the plastic deformation of zinc crystals has been described by Mark, Polanyi and Schmid3 and by Mathewson and Phillips14 and is regarded as being accomplished by block movements or * Investigator, Rolling Mill Section, Research Division, New Jersey Zinc Co. f Investigator, X-ray Laboratory, Research Division, New .Jersey Zinc Co. 1 Variations of structure throughout the cross-section of wire have been reported in the literature. 2 This alloy contained, in addition to zinc, 1.0 per cent copper and 0.01 per cent magnesium. Its crystal form is hexagonal close packed, the sarne as that of pure zinc. 3 H. Mark, M. Polanyi and E. Schmid: Vorgange bei der Dehrlung von Zink-kristallen. Zlsch. f. Phys. (1922) 12, 58. 4 C, H. Mathewson and A. J. Phillips: Plastic Deformation of Coarse-grained Zinc. Proc. Inst. Met. Div., A. I. M. E. (1927) 143. C. H. Mathewson: Twinning in Metals. Proc. Inst. Met. Div., A. I. M. E. (1928) 7. The results of a further study of plastic deformation of zinc as related to twin-

Jan 1, 1932

By Renato G. Bautista, Gary A. Beetner, Anthony L. Frey

The flow of material in a pump mixer-settler extractor was studied photographically and visually by injecting dye into the equipment and following its advance through the various sections of the equipment. Volumetric measure of the flow was obtained from analysis of the photographs. The organic portion of the settling chamber, the fluid surrounding the pump mixer, and the pump mixer itself were found to be operating in plug flow. The aqueous portion of the settling chamber was found to be partially mixed. Significant dynamic effect was noted due to density changes in the feed streams. The quantitative and qualitative observations made of the flow within a single stage should be of value in predicting the flow patterns in all similar equipment, including opaque and liquid metal solvent extraction systems.

Jan 1, 1973

By R. T. Carter

THE phase behavior of a number of binary systems consisting of paraffin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.1 However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the co-existing phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system.

Jan 1, 1940

By W. F. Burns

(Butte Meeting, August, 1913.) ATTEMPTS were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting- the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No.1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles.

Jan 7, 1913

By G. E. Kedzie

The ore-deposits of ail that portion of the San Juan country within the borders of Ouray County are either in the tertiary ernptives or, confined to a relatively narrow zone, in the sedimentary beds just beneath them. The ore-deposits in the igneous formation

Jan 1, 1888

By Thomas M. Drown, P. W. Shimer

In a communication to this Institute at the Baltimore meeting, February, 1879,* on the "Determination of Silicon in Pig Iron and Steel," the method recommended was the treatment of the metal with nitric acid until action had ceased, and then evaporating with sulphuric acid until the nitric acid was nearly or quite driven off. After filtration of the siliceous and carbonaceous residue, and washing with hot water and hydrochloric acid, a silica was obtained, on ignition, which was quite pore. Since this paper was read before the Institute, we have had large experience with the method, and

Jan 1, 1880

By Michael G. Schill, Mark C. Fischer

Since its introduction several years ago in the United States, the high pressure belt filter press has proven to be a highly cost-effective dewatering device in a number of mining and industrial applications. To evaluate the process and economic factors associated with the dewatering of coal refuse, a comprehensive program of laboratory and on-site pilot studies has been conducted. This paper will summarize findings of this study and discuss advantages of the belt filter press over conventional dewatering methods. The conventional means of dewatering thickened coal refuse involves the use of vacuum disc filters or centrifuges. Due to the high amount of energy used to dewater refuse with these devices it was a logical course of action to apply belt filter press technology to this application, since a belt filter press will require less than 3.7 kW (connected).

Jan 1, 1982

By J. Brian Eby, T. I. Harkins

THIS paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling.

Jan 1, 1944

By Frederick N. Clark

These tests were made under the writer's supervision in the mining and metallurgical laboratories of the Massachusetts Institute of Technology, in the winter of 1888-89, by Mr. Robert C. Williams, of Marquette, Mich., assisted by Mr. J. B. Seager, of the

Jan 1, 1890

By Charles P. Williams

The lead-bearing area of Missouri has been subdivided, geographically, into the Southeastern, the Central, and the Southwestern

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

COMMITTEES. Iron and Steel. Albert Sauveur, Chairman. A. A. Stevenson, Vice-Chairman. Herbert M. Boylston, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. LOCAL COMMITTEES. Program Committee.-A. A. Stevenson, Chairman. Herbert A3. Boylston, J. E. Johnson, Jr., Henry D. Hibbard, E. Gybbon Spilsbury. Reception Committee.-J. R. Johnson, Jr., Chairman. Felix A. Vogel, William R. Walker. Dinner Committee.-E. Gybbon Spilsbury, Chairman. The opening session was held on Thursday morning, Oct. 16, 1913, at the Institute Headquarters in the Engineering Societies Building, 29 West 39th Street, New York, N. Y., and was called to order by President Rand, who addressed the meeting briefly before presenting Albert Sauveur, who responded to the President's address, and presided at the meeting. The following papers were then presented in oral abstract by their authors or authors' representatives: The Cleaning of Blast-Furnace Gas, by W. A. Forbes. Discussed by S. K. Varnes, H. N. Diehl, F. H. Wagner, Joseph Hartshorne, S. B. Marshall, J. W. Richards, J. E. Johnson, Jr., W. A. Forbes, and others.

Jan 12, 1913

By J. P. Norris, W. T. Pettijohn

The Mufulira Copper Mine, Ltd., is in Northern Rhodesia, ten miles from the Belgian Congo border, and is one of the group of four operating mines comprising the Northern Rhodesian Copperbelt. The ore deposits at Mufulira are on the limb of a large syncline striking NW.-SE. and dipping NE. at about 45 deg towards the Congo border. The host rocks are well-consolidated, highly-silicified, felspathic quarzites of the lower part of the pre-Cambrian Séries des Mines of the Katanga. The ore rocks are underlain, unconformably, by the older "Muva Series," in this case hard, green, metamorphosed quarzites. There are three superimposed orebodies, the first, or upper, orebody averaging 40-ft true thickness with a strike length of about 5000 ft, the second, or middle, orebody of about 50-ft true thickness with a strike length of about 6000 ft, and the third or lower orebody of around 60-ft true thickness with a strike length of 8000 ft. The orebodies are separated by varying widths of waste, or very low-grade ore, from a few feet up to 50 ft. The middle and lower orebodies are so close together for a strike length of 3000 ft that they are mined as one orebody. In all, the mineralized zone is about 200 ft in true thickness.

Jan 6, 1950

By Amos Bowman

In the last two years I have had an opportunity to study the conditions of gold-mining in the far northwest of the Pacific coast —in Cariboo district, British Columbia. That country joins Alaska

Jan 1, 1887

By A. E. Austin, J. R. Doig

Ti-Cr alloys age harden after B-quenching by formation of an W-phase. The structure and orientation of this transition phase have been determined. The hardness ap-pears to be caused by strain in the B-matrix produced by concurrent enrichment of alloy content in the W-phase. EARLY studies of age hardening in B-stabilized titanium alloys revealed the formation of a transition phase named o' This phase was detected by X-ray diffraction in binary alloys of Ti-Fe, Ti-Cr,

Jan 1, 1958

Arrangements have been completed in New York whereby the re- sources of The Engineering Foundation, under the auspices of the four principal national engineering societies, are placed at the disposal of the National Research Council, which was appointed by the National Academy of Sciences* at the request of President Wilson. The object of the Council is to coordinate the scientific research work of the country in order to secure efficiency in the solution of the problems of war and peace. The Council was without funds until The Engineering Foundation, established to further scientific and engineering research, offered to place its resources at the Council's disposal, including the services of its secretary, Dr. Cary T. Hutchinson, to act as-secretary of the Council. The offer was accepted and plans for immediate activities have been placed in the hands of an executive committee. In indicating how thoroughly, every branch bf science and engineering is represented, Dr. George E. Hale, Director of the Mt. Wilson Solar Observatory, and Chairman of the Council, when he was in New York attending to the details of the arrangement, called attention to the personnel of the body, saying that it is the purpose to enlist the cooperation, in the solution of our industrial and military problems of a scientific character, of every possible established agency. Medicine, for example, is represented on the Council by Dr. William H. Welch, President of the National Academy of Sciences, Brigadier General William C. Gorgas, , Surgeon Crenera.1 of the United States Army, Dr. Simon Flexner, Director of the Rockefeller Medical Institute, and Dr. Victor C. Vaughan, Past President of the American Medical Society; biological science by Dr. Edwin G. Conklin, Professor of Zoology, Princeton University; chemistry by Dr. A. A. Noyes of Massachusetts Institute of Technology and Dr. L. H. Baekeland; physics by Dr. A. A. Michelson of the University of Chicago; and electricity by Professor M. I. Pupin, of Columbia University.

Jan 10, 1916

By P. Payson

EMBRITTLEMENT of hard-tempered martensite (500°F embrittlement) appears to be coincident with the beginning of the third stage of tempering. During the first stage, primary martensite of steels containing over 0.25 pct C decomposes to a mixture of c carbide and martensite of appreciably constant carbon content close to 0.25 pct.' During the third stage of tempering, cementite forms. In steels with

Jan 1, 1955