Search Documents

By A. B. Dyes, P. H. Braun, B. E. Cole

This paper presents a reservoir engineering analysis of the performance data for a waterflooding project in the Johnson Lease, South Ward field. This type of engineering analysis adds to the knowledge of the mechanics of water flooding. This study reveals that in general (a) high ultimate areal sweep-out efficiencies (95 to 100 per cent) can be expected, and (b) cross-flow among strata of different permeabilities during the fill-up phase can have an important influence on the behavior and should be dealt with in studying reservoirs for water flooding. The analysis further showed that the recovery predictions based on what was considered a consistent interpretation of core data and logs were low because little contribution was assumed from the low permeability, oil-bearing sand sections which have apparently yielded considerable waterflood oil. This project has yielded in excess of 2 1/2 times as much oil by water flooding as by primary depletion. These very favorable results were achieved without the use of any special injection well completion techniques. However, all of the low permeability material war included in the section open to injection despite its poor estimated primary yield. LEASE PERFORMANCE HISTORY The South Ward field lies in the southeast corner of Ward County near the southern tip of the tremendous Yates trend. Deposition of sand bodies along the seashore reefs during the latter part of the Permian period established what have turned out to be ideal conditions to form a great number of independent productive sands. Probably, these reservoirs in Ward and Winkler counties are providing operators with some of the nation's richest sources of secondary oil reserves through the use of waterflooding techniques. In South Ward field water has been very successfully used to flood oil from the Bennett sand occurring at a depth of about 2,300 to 2,400 ft. About 150 ft above the Bennett sand reservoir, the Grand Falls sand produced gas from a large cap extending over most of the field. The Atlantic Refining Co.'s 320-acre W. D. Johnson lease (Fig. 1) is on the northwest edge of the structure with only gas cap apparently present in the Grand Falls sand. The Bennett sand under this lease is oil productive, however, having a gross sand thickness averaging about 80 ft with a net of 18 ft of fairly clean, highly permeable sand, and about 36 ft of oil-bearing sand with low permeability and high water saturation. The lower permeability sand is interbedded with numerous layers of lime, shale, and anhydrite. Radioactivity logs from 12 wells and cores from two, examples of which are shown in Fig. 2, reveal that the total Bennett sand pore volume is about 71,000 bbl/acre. The estimated initial water saturation averages 41 per cent in the 54 ft of sand considered to contain oil; thus, also considering an estimated 18 per cent oil shrinkage, the lease originally contained about 34,000 bbl of oil per acre. Original pressure was probably about 1,400 psig. PVT correlations indicate that the reservoir fluid was originally saturated with gas. After discovery of the field in 1930, Atlantic completed the first well on the Johnson lease in March,

Jan 1, 1958

AS we contemplate the bestowal of the John Fritz medal year after year on men of wide-world dis-tinction in the various fields of engineering, men who in one way or another have given impulse and direction to the progress of mankind, the question becomes inter-esting as to what manner of man was John Fritz and what were the qualities that singled out his name to be so conspicuously associated with the world's great scientific and industrial achievements. If, as Lowell said, it is the duty of the nation to pro-duce great men, our country surely rose to her oppor-tunity when she guided and guarded the career of John Fritz. Starting life as a blacksmith with no advantages of education, without influential friends or the favor-ing accidents of fortune, he advanced steadily in use-fulness, power and respect of his fellowmen until by common consent he occupied the first place in the domain of the steel industry of this, country. The numerous honorary scientific memberships conferred upon him in this country and abroad attest the esteem in which he is held by his fellow engineers. Twenty years after his retirement from active business at the age of seventy, he lived to enjoy, as few men have been permitted to do, the fame and the friendships which he had so amply earned. His sterner qualities of industry, integrity and sterling character were re-lieved by unfailing human sympathy, humor and spon-taneous good-will toward his fellowmen. To all who

Jan 3, 1928

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

A development which could prove significant was the announcement on September 18 by Lone Star Industries, Inc., Greenwich, Conn., that the Snyder process which utilizes shock phenomena to break down ore in seconds, is operational. J. R. Kringel, chairman and president of Lone Star, says this about the process: "This new approach to the comminution of ores not only provides better mineral liberation at lower capital and operating costs, but it also makes a significant contribution toward the more efficient utilization of the country's rapidly depleting mineral reserves." The Snyder process consists of loading the material into a chamber, introducing a compressible working fluid such as steam under 300-500 psi, or as low as 80 psi, and then opening a millisecond-action discharge valve, causing the material to become entrained in the expanding fluid. The mixed fluid moves through a duct toward a discharge zone at near-sonic velocity, and is subject to a variety of extreme shock phenomena which accomplish the desired size reduction and mineral liberation.

Jan 11, 1972

By E. M. Bennett

HISTORY In 1923 John Campbell Miles discovered the Mount Isa deposit after finding and submitting for assay some “unusual and heavy rocks”. Six months after submission he received the assays of his original samples which indicated high lead-silver values. The deposit area was isolated and unknown geographically and not served by even a rough country road. The isolation of Mount Isa coupled with the depression years had a strong influence on the rate of development of the area. These two factors resulted in a slow amalgamation of the early individually held leases and the lack of ready finance to begin serious mining of the deposit. Initially, surface lead-silver-zinc mineralisation was proved and diamond drilling to shallow depths showed the presence of a viable orebody. Limited underground development work was initiated and open cutting associated with glory holing commenced. Due to the metallurgical problems associated with the ore and due also to unsuspected change in metallurgical conditions as the ore deepened into what is known today as the transition zone, major problems of finance were recurring at frequent intervals. Despite low metal prices the development of the mine continued due to continuing infusion of capital. During the 1939-45 war years a surplus of lead was being produced in Australia, but a grave shortage of copper was apparent. About this time copper ore had been found to the hanging wall of the then known major lead orebodies. At the request of the Australian Government, lead production ceased and copper production commenced.

Jan 1, 1970

The American Institute of Mining Engineers, the second of the four great national engineering societies established in the United States, was organized in 15,71. Its membership is composed of men engaged in the different branches of mining, metallurgy, geology, and chemistry. It includes both those who have worked their way up from the ranks and graduates from mining schools and universities, and at all times has counted in its membership leading technical educators. By a letter ballot of the members of the Institute, it was voted, at the annual business meeting of the Institute on February 18, 1919, to change the name of the American Institute of Mining Engineers to the American Institute of Mining and Metallurgical Engineers. The vote for the amendment to the Constitution making this change was a heavy one for such matters. It is the consensus of opinion that this marks an epoch in the history and usefulness of this Institute, and it is expected that the change will presage a large and healthy growth in metallurgical fields. Many metallurgists who knew nothing about min¬ing were loath to join a society of mining engineers, despite the fact that over 35 per cent. of the papers published in our Transactions during the past five years have dealt with metallurgical subjects.

Jan 1, 1923

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By M. S. Burton, H. H. Kranzlein, G. V. Smith

The influence of up to 2 at. pct of Ni and Pt on the yield strength of mono- and polycrystalline high-purity iron has been evaluated at temperatures from + 25° to -196°C. Current theories of solid -solution strengthening fail to explain the experimental observations. The temperature dependence of yield stress was found to be less in the alloys than that in high-purity iron. The room-temperature yield stress increased with alloy content, but at —78°C the yield strength first decreased with increasing a1loy content. AS a result of many studies, a number of theories have been proposed for solid-solution strengthening. The purpose of the present study was to evaluate these theories, as applied to the solid-solution strengthening observed in Fe-Ni and Fe-Pt alloys. Of various theories of solid-solution strengthening, those of Cottrell,1,2 Fisher,3 Suzuki,4 and Mott and Nabarro5 are most prominent, and have been discussed widely in the literature.'-' Of the recent concepts of solid-solution hardening the work of Fleischer9 is notable. Each of these models has been applied to particular alloy systems with some success, but in general none has proved generally applicable. In many of the previous studies to assess the effects of alloy additions in ferrous systems, lack of adequate control of the purity and grain size of the materials has obscured strengthening effects, so that few comprehensive data relating composition, temperature, and change of lattice parameter have been determined. In the present investigation an attempt was made to obtain data which would be meaningful in evaluating the theories of strengthening. Materials of high purity were used to minimize extraneous impurity effects, and both single crystals and polycrystalline materials were studied to evaluate the effect of grain boundaries. Nickel and platinum were chosen as alloy additions, because both belong to the same chemical group and have the same crystal structure and valence, with markedly different atomic diameters. It appeared that some conclusions regarding atomic size effect on strengthening might be made. MATERIALS AND PROCEDURES Fe-Ni and Fe-Pt alloys containing 0.5, 1.0, 1.5, and 2.0 at. pct alloy additions were prepared from high-purity materials. The iron was supplied by the American Iron and Steel Institute from a stock of 99.98 pct zone-refined iron prepared by Battelle Memorial Institute. The minimum purity of the nickel and platinum used for alloying was 99.98 and 99.999 pct, respectively. Alloys were prepared by levitation melting, cast into cylindrical copper molds, and cooled, all under a partial pressure (0.3 atm) of purified helium. Samples were 0.375 in. in diameter and weighed 20 to 25 g. Chemical analyses of the alloys are given in Table I. A sample of unalloyed iron also was cast as a control specimen.

Jan 1, 1965

By C. W. Schulties, W. J. Mallio, L. J. Petrovic, J. A. L. Campbell

Roof control comprises about 35% of direct and indirect underground mining costs. In addition, difficulties in estimating roof control costs for new areas lead to the greatest uncertainties when negotiating coal contracts. And obviously, coal cannot be mined if the roof can't be held. Accordingly, there are strong incentives to attack this problem on as many fronts as possible. One successful geological modeling technique for predicting future roof conditions was recently applied at Peabody Coal's Simco mine No. 5, located in Coshocton, Ohio. Benefits derived from it included: - A better identification of areas where poor safety conditions may be encountered. - Improved roof control cost estimates for contract negotiations. - Estimates of time-duration while mining in bad roof areas. - Labor and materials cost predictions in an existing mine. - Productivity increases through prior knowledge of areas to avoid.

Jan 10, 1975

By R. L. Frantz, R. W. Bouman

The authors investigated the comminution of quartz and limestone mixtures in a ball mill, showing that the distribution modulus of a comminuted material is the same whether it is ground separately or as part of a mixture. Analysis of the ground products indicates that quartz and limestone consume energy during ball milling in proportion to their mass fraction in the mixtures. Recently Schuhmann' made a significant contribution to comminution theory by proposing that complex comminution operations comprise the summation of many individual comminution events. By means of the single comminution event hypothesis, Schuhmann derived the Charles energy-size reduction relationship by considering that fragments of every particle crushed during a single impact have a size distribution characterized by the Schuhmann size distribution. In this paper, the size reduction of mixtures of solids in ball mills is analyzed by considering that size reduction occurs as many single comminution events. If a mixture of two materials is being ground in a ball mill, each successful impact of a ball with a particle of one material should yield an assembly of particles whose size distribution is characteristic of that material. Considering both materials to follow the Schuhmann size distribution equation, the size distribution of material 1 in the product is

Jan 1, 1962

The 48th convention of the International Union of Mine, Mill and Smelter Workers, held in New York City recently, saw delegates vote funds for a new organizational drive expected to begin immediately. John Clark, union president, told members in his keynote speech, that the union would be in a better position to make demands if it extended its membership to all phases of the nonferrous -industry. He told the 250 delegates that union leaders have already laid extensive groundwork for the campaign. Clark said: "I am proposing here that we concentrate on organizing during this coming year. I am proposing that we throw a heavy amount of re sources in organizing. That means financial resources as well as re- sources of staff ."

Jan 1, 1952

By B. C. Allen

Grain-boundary gvoocing was studied irz chronziu?n. molybdenum, tungsten, and the solid-solution alloys, Cr-35Re. Mo-33Re, and W-25Re at 0.6 to 0.9 of the absolute liquidus temperature under an inevt atmosphere , foveign nzetal zlapor, and liquid metal. The controlling mechanism of matter transport was deduced frolr groove size and shape. kinetics of growth, and cotnparisoz with theoretical relatiotzships derived by Mullins. Grooves in chowzizon formed prittzarily by volume diffusion tkrongk kelium or argon at 1 atm pressure and by e1)apovation-condensatiotz in a static vacuum. Groozles in the other nzetals and alloys forrned priniarily by sirface diffusion, the coefficients of which were calculated. Carbon was found to decrease the acti7:ation energy for surface diffusion on molybdenun. Sitrface diffusizities weve sinzilav for iWo-0.0ZC and Mo-33Re. The presence of about 1 -?nm pressure of silver or tin vapor did not affect the neckanis)n of grooz;e formation. In liquid titz or silz:er, pain bolindary gvooves formed by zolume diffusion in the liquid. BASED on theories of ullins," the mechanisms of grain-boundary grooving have been determined for low-melting metals such as copper in an inert atmospheres or in liquid lead.4 The purpose of this investigation was to study grain-boundary grooving in the refractory Group VI-A metals, chromium, molybdenum, and tungsten, and the bcc solid-solution alloys, r-35e, 0-33e,= and -25e,' at 0.6 to 0.9 of included to see whether Mullins' theories were applicable to them as well. EXPERIMENTAL WORK The materials chromium, molybdenum, tungsten, Cr-35Re, Mo-33Re, and W-25Re were in the form of 0.050-cm-thick sheet assaying 99.98 pct or better. The nominal carbon level was generally 30 ppm. The oxygen + nitrogen + hydrogen content was -50 ppm. Mo-33Re and W-25Re were prepared by powder-metallurgy methods and supplied by Chase Brass and Copper Co. The remaining materials were arc-cast. Chromium and Cr-35Re were prepared at Battelle by arc melting, extruding, swaging, and rolling. Mo-0.003C was supplied by Climax Molybdenum Co., and Mo-0.02C and tungsten by Universal Cyclops Corp. As a source of liquid metals, tin and silver granules assaying 99.98 pct were used. Spectrographic analyses indicated the presence of -100 ppm each of iron and silicon. Vacuum melting reduced the combined gas content to c5 ppm (2.60,, 0.9N2, 0.4H2 in tin and l.602, 0.7N2, and c0.04H2 in silver). Specimens were prepared for grain-boundary grooving. Coupons 0.5 by 1.5 cm with a small hole in one end, or substrates 1.5 by 1.5 cm, were cut from sheet. The specimens were annealed in containers of the same material to provide a vapor-solid equilibrium as well as to protect them from gaseous impurities. Outgassing was done at 2 x 10"5 mm for 15 to 30 min at 1150°C for chromium and Cr-35Re, 1750°C for molybdenum and Mo-33Re, and 2600°C for tungsten and W-25Re. Then recrystallization to a stable grain size of about 0.5 mm was accomplished by annealing at least 1 hr at 1600°C for chromium, 1800°C for Cr-35Re, 2350°C for molybdenum, and 2300°C for Mo-33Re in a rhenium-element resistance furnace under 1 atm of static argon or helium. The atmosphere was gettered by tantalum radiation shielding. Tungsten and

Jan 1, 1967

E. M. BROHL. It seems as though the physicists in this crowd in the case of the cartridge cases have been a little in advance of the chemists in the crowd. What I am curious about here, and the way this appears to me, without too much study, is that in season cracking we get an atomic distortion so that both by sound means and by magnetic means we are finding a reluctance of the atomic planetary system to line up in accordance with the so-called good metal. The point that is brought up, or rather that has not been brought up-and I think perhaps we could think of that from the chemical point of view-is that this season cracking as I am used to the stress-corrosion cracking, appears to act much as though it were copper oxide. You remember when YOU take copper oxide films in which we again use this distortion of the atomic system to allow currents to pass selectively in one direction only, we get results almost identical with what we saw on the oscillograph report. In other words, on the one section of this season cracking we had a trace of one phase and if you notice on the sections three and four of the numbered oscillograph trace we had what appears 180 deg. out of phase.

Jan 1, 1945

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steel-making methods, the basic open-hearth process is one of the most versatile, both from the stand- point of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. In the case of some types of liquid-metal charges the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF THE BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SO2), manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course of the

Jan 1, 1944

By A. Bentzen, S. S. Wong, W. K. Fletcher, B. J. Price, A. J. Sinclair

One hundred eleven pyrite samples from three porphyry-type deposits in the Canadian Cordillera were analyzed (many in duplicate) by AA spectrophotometry for Co, Ni, Cu, Pb, Zn and Mn. All elements have density distributions that are lognormal or combinations of lognormal populations. Co and Ni in pyrites show zonal patterns that relate generally to mineralogical zones in the porphyry systems, particularly if contoured as the Co/Ni ratio. High Cu and Mn values in pyrites also correlate with Cu-rich mineralogical zones. Other elements studied appear less regular in their distribution patterns, although Pb and Zn highs in pyrite seem to occur sporadically near the margins of porphyry systems. These data considered with two other studies permit construction of an empirical model for the distribution of certain minor elements of pyrites from porphyry systems of the calc-alkalic suite. In particular cases pyrite geochemistry shows potential as an exploration tool to aid in target definition for detailed exploration.

Jan 1, 1978

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given com- position and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO) . This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1964

HE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe2O3), and phosphorus oxide (P2O5) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1951

By Lucien Eaton

IN anticipation of a shortage of labor for hand-tram-ming at the Cliffs shaft mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., early in 1923 three 4-ton Goodman storage-battery locomotives, equipped with Edison batteries, were purchased. Storage-battery locomotives were chosen for this work because the expense and time required to put up trolley-wire and to bond the rails of the complicated system of tracks on the levels, where the locomotives were to be used, would not have been warranted by the amount of ,ore to be handled. The only changes in the tracks necessary for storage-battery locomotives were new switches and extra ties and braces on curves. The tracks were 24-in. gage, and were laid with 20-lb. rail. Edison batteries were chosen, because it was desired to charge the batteries from the trolley circuit already, in the mine, and this would have been impracticable with lead batteries. Each locomotive is equipped with 126 A-4 Edison cells, which are charged in series from the 240-volt trolley circuit while the trolley locomotives are running; and are discharged in parallel in two banks of 63 cells each. These locomotives were so successful that later 5 smaller locomotives, weighing 11/2 tons each, were pur-chased for use e with cars that are filled by hand and on levels where the amount of ore handled is small. These locomotives, built by the Geo. D. Whitcomb Co. of Rochelle, Ill., are equipped with batteries of 40 A-4 Edison cells each, the cells being the same as those, on the larger locomotives. They are charged from mer-curial-are rectifiers. These locomotives are operated by the trammers themselves, and have not special oper-ators like the larger machines. The trammers are all young men of American birth, and take quickly to the operation of machinery, and the simplicity of the con-trol on these locomotives has made special training unnecessary. A survey of the results was made by the A. C. Nielsen So., an excerpt from which follows: Eight Edison-equipped battery locomotives are now in use at an Ishpeming mine of the Cleveland-. Cliffs Iron Co. This equipment was installed to take the place of men who formerly pushed loaded cars by hand. Results have been very satisfactory and the de-pendable, trouble-free operation of the Edison batteries is considered to have been an important factor in the effectiveness of the new hauling method.

Jan 3, 1927

By Earl L. H. Sackett

This laboratory centrifuge is unique in its low cost and ease of construction, its particular adaptability to problems encountered in an ore dressing laboratory and its simplicity of operation. It will treat a sample of the size ordinarily used in a laboratory flotation test. The centrifuge was designed at the Baroid Sales Division of the National Lead Co., Malvern, Ark., and built in a local machine shop to serve as a laboratory machine which would produce results comparable with those obtained in the large scale centrifugal deslimers in use in our Magnet Cove mill. The apparatus has served quite well in this capacity and has also proved effective as a deslimer on a variety of ore dressing problems. The cost of making this machine was relatively low and it is simple to operate. It is strictly a batch machine, but when operated under proper conditions, gives results which agree quite closely with large continuous-flow machines of the same type. Effective separation of minus 5 and 10 micron material is made in an undispersed pulp in a short time.

Jan 4, 1950