Search Documents

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the inter-relationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large. Coming to the specific points to which Mr. Borden has drawn our attention, I will touch on the corresponding provisions in Canadian federal tax law, by way of comparison and contrast.

Jan 7, 1950

By Bruce E. Grant, Thomas Jancic, Lawrence G. Dykers, Frank Buchella

Principal factors influencing equipment selection can be grouped into five basic categories: tonnage requirements, ore and waste; topography and property line considerations; ore control requirements; physical characteristics of ore and waste; and climatic considerations. Loading, transporting and ground preparation equipment are largely determined by tonnage requirements. Large size equipment is appropriate for a production of about six million tpm, medium size for three million tons and small size for one million tons or less.

Jan 12, 1973

By Henry S. Munroe

The plan of organizing a summer class of students of tha Bchool of Mines, for the practical study of mioing and miner's work, rewived at the outset the following cordial indorsement: ...." 1 have thonght over the plan proposed by you of taking the students to the mines during the summer, acd of having them actuaily ttrke part, under the direction of skilled worktnbn, in dl the various kinde of mining work; and of using them as a cerps of engineers to make inside and outside surreys, particularly with a view to the detailed study of the geology of the mine. I have no beitation in saying, that if the students have been previously instructed in the theoretical part of thrir studies, by lectitras and practice during the winter, the plan would be an admirable one. Of courae experience will suggest modiflcations of detail. Frorn the work you have done at our mines this spring, I feel sure that you would be perfectly competent to curry out your plan, and 1 shall gladly aid you in uny wny I can. " Yours, sincerely, The plan of the proposed summer school thus indorsed by Mr. Coxe was adopted by the trustees of Columbia College, and an appropriation of one thousand dollars, or so much thereof ss might be necessary, was voted for the experitneat. A volunteer class of thirteen students was formed, and the first summer school was held at Drifton, in July and August of that year (1877). The following extract, from an editorial notice in the iden of the organization of the school and the work required of the stiudens. "The students, on reporting to Professor Munroe, were divided into sqoade of two or three men each, and on Monday, July 2d, were aesigned to the qre of skilled miners, selected for the purpose by the mine boss, for instruction in gangway work. Half of the students worked in the morning and the other half in the atternoon, one squad at a time with each miner, The times of going and coming to and from work were so arranged that each student spent four to four and a half hours in the mine each day. While in the mine they assisted the miner to load his car, thereby learning readily to distinguish I slate ' and

Jan 1, 1881

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal. The patent literature gives information on some of the methods proposed. Esselen and Weiss 1 have patented the deposition of a coloring material in the valleys of the surface of the coal. Sperr2 covers the quenching of coke with water containing a pigment or dye that will deposit on the coke. He also suggests electroplating with copper or nickel. Glinsmann 3 subjects the freshly fractured coal surface to the action of an alkali or alkali earth ferricyanide and a ferric salt. Barsky and Hanson4 specify a method for the application of the same chemicals covered by Glinsmann.

Jan 1, 1943

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By J. Leland Myer

IN a precise study of Pennsylvania anthracites, the research on European. anthracites is of little value to us because of their different physical and chemical nature. Likewise, there can be little correlation with the physical properties of bituminous and lower rank coals. Although all high-rank coals are thought to have had a common origin, microscopic examination revealing essentially the same kinds of organisms in similar .states of preservation, the different physical properties apparently arise from the degree or kinds of metamorphism of these coals. Representative samples from the Pennsylvania deposits have been selected for analysis, together with graphitic anthracite, bituminous coal, and some of the common forms of carbon. A complete list, with descriptions, is shown in Table 1.

Jan 1, 1932

By H. M. Howe, E. C. Groesbeck

Fig. 1 shows a volute aging break which developed spontaneously in a hardened and tempered steel helmet between 19 and 38 days after it had been tested ballistically. A similar break, shown in Fig. 2, developed spontaneously in a similar helmet about 40 days after the ballistic testing. In this case the rupture occurred abruptly and with a loud report. The path of rupture in this second case, though much the less regular, is the more interesting of the two, in that it is an approximation to two parallel volutes centered at the point of impact of the projectile, just below D. Several weeks later, after the photograph for Fig. 1 was taken, a similar doubling of the volute crack occurred in this helmet, starting from the end of the eyelash crack near A and spreading thence to the left contra-clockwise for about 1/2 in. The negatives from which these pictures are made have not been touched up in any way, save writing the letters on them. In both cases the trajectory of the bullet was normal to the initial surface at the point of impact, and in both the helmet passed the ballistic test without detectable cracking, under a velocity of impact not far below that which usually causes perforation. The initial surface itself was very nearly spherical throughout the region covered by the break.

Jan 1, 1920

TULSA SECTION At the smoker concluding the two day meeting of the Tulsa section of the American Institute of Mining and Metallurgical Engineers, Tulsa, Okla., Feb. 26, 1919, Dr. Willis T. Lee, the new head of the Geological Department of the University of Oklahoma, was introduced to the assembled geologists and mining engineers. Dr. Lee requested that the geologists and engineers who were making a specialty of petroleum geology assist him in giving a good course in practical oil geology in the Geological Department of the University. After a motion offering the services of all present in giving lectures on their special subjects had been adopted, Dr. Perrine of Hutchinson, Kans., named the geologists who were pledged to give lectures in Dr. Lee's course. The students in geology at Norman are assured of the latest information regarding practical work in petroleum geology and will have the inspiration derived from contact with men who are actually at work upon the problems which they are studying. Dr. Lee and President Brooks of the University are to be congratulated upon the introduction of this .method of instruction. The plan thus put into operation is similar to the graduate system of coaching in athletics followed at many of the large universities; what is good for instruction in athletics should also prove good for instruction in applied geology.

Jan 6, 1919

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

DISCUSSION, M. Cohen presiding A. H. Geisler and D. L. Martin (GeneTal Electric Research Laboratory, Schenectady, N. Y.)—We were rather interested to note the author's conclusion that the cubic to tetragonal transformation may be of the second order, for we have been able to show that the order-disorder transformation in an analogous alloy system is a first-order transformation with a discon-

Jan 1, 1952

By W. R. Opie

The object of this paper is to show the manner in which typical electrodeposits of hexagonal-close-packed metals—zinc, titanium, and zirconium—tend to form. The conditions of electrodeposi-tion markedly affect the nature of the deposits in regard to crystal size, orientation, and appearance. No attempt is made to correlate cell conditions with deposit quality but, rather, characteristic types of deposits were selected and a study made to show the relationship between outward appearance and crystal structure. The zinc deposits were made in aqueous electrolytes and the titanium and zirconium deposited from fused salt baths. ZINC deposits studied were made in the American Smelting and Refining Co.'s Central Research Laboratories. They were representative of bright, shiny, smooth deposits, which can be obtained by using proper current densities and electrolyte addition agents, and of deposits which are dull and tend to be nodular. Four deposits were selected which ranged from smooth and bright to very nodular and dull, and their classifications are shown in Table I. These were examined microscopically and were found to differ quite markedly in outward surface structure and in microstructure. The outward surface variation is illustrated in Figs. 1 to 4. At X50 the texture could be seen to progress from granular to platelike to smooth. The microstructures of the deposits' cross sections from starting sheet to outer surface are shown in Figs. 5 through 8. The dull nodular deposits (sample Nos. 1 and 2) show some tendency for acicular growth. The platelike sample (No. 3) shows tendency for columnar growth development and the smooth deposit (No. 4) has a well developed columnar structure. Back-reflection X-ray patterns of the deposit surfaces revealed some interesting information. The crystal orientation was random in all deposits except the smooth deposit. Fig. 9 is a typical back-reflection pattern of a nodular deposit. All planes are reflecting in the proper relative intensity. The pattern of the smooth deposit is shown in Fig. 10. The only planes which reflect are the (10.4). This series of planes is in the right position, with the FeKa radiation used, to satisfy the Bragg equation if the basal planes {00.1) are at right angles to the X-ray beam. The results were interpreted to mean that in the bright smooth deposit preferred orientation has occurred with the basal hexagonal planes oriented in the plane of the sheet but with all other planes randomly oriented around the c-axis.

Jan 1, 1957

By Helmer Hedstrom

THE purpose of this paper is to direct attention to the importance and the usefulness of phase measurements in electrical prospecting for ore, a subject about which virtually nothing has been published. The paper describes a new field method for ore prospecting, the "Turam" method, which makes use of phase measurements, and which has been used with great success for five years. Of the principal geophysical prospecting methods, the gravimetric and magnetic methods determine the direction and strength of the static fields of force of the earth. By seismic and electrical methods, fields of force are applied to the block of ground under investigation. By these methods a third parameter can be measured, besides the direction and strength of the field; namely, the time of arrival of the applied field at the different observation points. This time of arrival has been practically the only parameter measured in seismic work, while in electrical pros-pecting it has generally not been considered, the measurements having been limited to determination of direction and strength of the applied field.

Jan 1, 1937

By John A. Bonucci

AMAX Base Metals R&D, Inc. has developed technology for extracting and recovering platinum and palladium from spent automobile exhaust emission control catalyst. Our most promising route is a chloride-based hydrometallurgical flowsheet in which catalyst pellets or crushed monoliths are leached in HC1 with an oxidant at 95°C without agitation. Alumina co-dissolution can be limited by thermal pre-treatment of the catalyst. The leach solutions are treated by one of several precious metals recovery techniques to produce a high grade PGM concentrate. For the new generation of three-way catalytic converters which contain rhodium, an H2S04 preleach could selectively extract much of the rhodium while leaving the platinum and palladium behind. Capital and operating costs will be discussed.

Jan 1, 1984

By C. T. Young, J. L. Lytton

In recent investigations,1,2 the strength and thermal stability of dislocation substructures prepared by 5 to 25 pct room temperature tensile straining and recovery annealing at 120°, 160°, and 200°C have been studied in randomly oriented polycrystalline high purity aluminum. The techniques of transmission electron microscopy revealed that a major source of the strength and stability of dislocation substructures was the formation, during room temperature straining, of well-defined cells bounded by dislocation tangles which rearranged into nearly perfect dislocation networks during recovery, forming the boundaries of subgrains. The strength of such substructures increases with decreasing cell or subgrain size,2"6 and the formation of fine subgrain structures can provide thermally metastable strength at low temperatures and can favorably alter the course of primary creep at elevated temperatures.7'8 For maximum benefit, however, sub-grain growth should be reduced or eliminated. It was, therefore, decided to investigate the use of heterogeneous precipitation on dislocation networks as a means of imparting increased strength and thermal stability to subgrain structures through effective pinning. C.T. YOUNG, STUDENT MEMBER AIME, and J. L. LYTTON, Member

Jan 1, 1970

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

Seismological Society of America, University of California, Berkeley, Calif. Perry Byerly, Secretary. The Bulletin of the Seismological Society of America is issued quarterly. The four numbers each year are collected in a volume; in 1932 the 22nd annual volume was published. The articles contained in the copies of the Bulletin are not, perhaps, of direct interest to a mining engineer but many of them will interest geologists. To indicate the type of articles contained in the Bulletin, the following titles, taken from the current issue, for June, 1932, are given: The Japanese earthquake of march 28, 1925, and the Problem of depth of focus; the earthquake in Santa Monica Bay, California, on August 30, 1930; a new vertical seismography. For copies of the bulletin or information concerning them, address the above.

Jan 1, 1933