Search Documents

By W. E. Bron, E. S. Machlin

GRAIN boundary migration in V-shaped thin specimens of high purity silver was studied. Each specimen contained two crystals having the relative orientation: (111)A/(111)B; (ll0)A/(101)B. The boundary between these two crystals varied between a continuous curved and an alternating two plane interface. The plane interfaces were oriented parallel to (101)A/(011B) and (121)A/(211)B. Traces of these planes are shown in Fig. 1. Evidently the two plane interface, although of higher area, comprises lower total interface energy than the average curved boundary it replaced. The plane boundaries were found to move at 650 °C to consume the broad segment of the V opposite to the direction of interface area and energy decrease. On investigation, using the thermal etching technique of Hendrickson and Machlin,1 it was found that the outer grain contained 8.3x108 more dislocations per cm" than the grain at the apex of the V. Consequently, the boundary moved to decrease the strain energy associated with the difference in dislocation density across the boundary. The rates of motion of specific {110} and {112} boundaries were measured during interrupted anneals at 650°C by referring the position of the boundaries to each other and a fiducial line on the specimen surface. The measured rates of motion are 0.075 and 0.025 mm per hr for the {110} and {112} boundaries, respectively. Plots of grain boundary motion vs time of annealing show straight lines with little deviation of data points from these lines.

Jan 1, 1957

By G. A. Perry, C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). PED is a method by which predesigned pushbacks are sequenced into an optimized period-by- period design. The design that PED Produces is the design used in the field without further modifications. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system. It is in operational use.

Jan 1, 1984

State of Indiana, Department of Conservation, Division of Geology, Indianapolis, Ind. W. N Logan, State Geologist A list of the publications will be sent upon request. A series of yearly reports have been issued, with a few early exceptions, since 1869, up to and including the 41st (1916) Five of these are issued free, 18 are out of print, and the rest may be obtained at a quoted price. Beginning in 1917, the administrative reports of the State Geologist have been published in the Indiana Year Book. In 1919, the Department of Geology and Natural Resources became the Division of Geology in the Department of Conservation and separates of later reports in the Year Book are available, as follows. 3rd Report (1921), Gold in Indiana, 4th (1922), The New Albany shale, peat deposits of Indiana; 5th (1923), Petroleum conserva¬tion, 6th (1924), Conservation of natural gas; 7th (1925), Coal losses of Indiana, 10th (1928), Geological conditions in the Siosi oil field, 11th (1929), The mineral fuel resources of Indiana, 12th (1930), Oil and gas developments in 1930. (Titles of lesser interest are omitted ) The following Special Reports have been printed as publications of the Department of Conservation: Special Report 6, Kaolin of Indiana (1919), free; 21, Handbook of Indiana geology (1922), $5 to nonresidents and $3 to residents, 42, Geologic conditions in the oil fields of southwestern Indiana (1924), 75 cents to non-residents and 50 cents to residents; 55, Geology of the deep wells of Indiana (1926), $1; 75, Geology of the Silurian rocks of northern Indiana (1928), $1, cloth bound, 8125, 78, Indiana oolitic limestone map of Monroe-Owens counties (1928), $1, 79, Indiana oohtic limestone map of Lawrence County (1928), $1; 90, The geologic history of the vertebrates of Indiana (1929), $1, cloth bound, $125, 91, The ceramic materials of Indiana (1929), free, 98, The Borden (Knobstone) rocks of southern Indiana (1931), $1 25, cloth bound, $150, 101, Insoluble residue studies of Mississippian limestones in Indiana (1931), 25 cents

Jan 1, 1933

By Lawrence Addicks

SOME three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed y constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge. was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust Were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and Was fired with fuel oil. A run of several hours yielded excellent nodules. The kiln showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal. of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per. ton of flue dust shown on the test and as fuel oil at that time Was selling around 2 1/2 c. per gallon it was decided to let it go at that.

Jan 7, 1914

By Alan K. Burton

The number of trucks required to perform a certain task is a function of the productive capability of one independent truck and the total tonnage required. Hourly productive capability of one truck is the product of trips, or cycles, per operating hour and effective payload. One cycle is made up of load, dump, and travel time, the sum of which comprises theoretical cycle time. This time is then derated by a productivity factor, giving an average effective cycle time which is used to calculate the number of cycles per hour. Rated payload is the truck's designed tonnage, while effective payload is the average amount that is actually carried. Manufacturers, particularly of the larger trucks, produce various body sizes designed to carry materials of different densities. However, it is not always possible to carry the rated payload because the material might be lighter than expected, a body of the required size cannot be produced, or because of spillage on particularly steep grades.

Jan 12, 1975

By Thomas E. Howard

Recipient of the 1975 D. C. Jackling Award - "For his vision and initiative in defining, planning, directing, and accomplishing mining research programs; for his leadership in focusing worldwide attention on the need for research to improve underground excavation for mining and civil applications; and for his lecture. . ."

Jan 1, 1976

By Eric Jette

THE results of an investigation of the ternary system iron-chromium-ilicon were reported in 1936 by the present authors.1 Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on .the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers,2,3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon ill molten iron-chromium-silicon alloys. Tofaute and his coworkers5,6 have made detailed studies of the iron-chromium-carbon system, which will he referred to later.

Jan 1, 1937

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By L. H. Levenson, Charles S. Barrett

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Charles S. Barrett, L. H. Levenson

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Henning Nielsen

SIX weeks ahead of schedule, the International Nickel Co. of Canada Ltd. has brought a 30-mile rail line into the newly born town of Thompson, Manitoba. Its construction spurs the development of a rich new mining region slated to become the world's second largest nickel-producing area-exceeded only by Inco's Sudbury, Ont., workings. Two mines, the Thompson and the Moak Lake, will be opened to meet International Nickel's scheduled annual production goal of 385 million lb of refined nickel by 1961. Accomplishment of this aim will mean an additional 75 million lb of the metal available to consumers. In addition, stepped-up out- put of Inco's Sudbury holdings may increase this figure by another 25 million lb. (For an earlier report on these developments see MINING ENGINEERING News, January 1957).

Jan 12, 1957

PETROLEUM DIVISION Established as a Division March 24, 1922 Paul R Turnbull, Chairman John R McMillan, Vice-Chairman Morris Muskat, Vice-Chairman William E Stiles, Treasurer Joe B Alford, Executive Secretary 408 Trinity Universal Building Dallas, Texas

Jan 1, 1952

By W. F. Shinners

Ozark Ore Co.'s Iron Mountain mine utilizes optimum mechanization to provide ever increasing output from underground as production declines from open pit. Trackless equipment gave flexibility to meet varied mining conditions-required minimum of pre-production development.

Jan 4, 1953

By H. W. Knott, M. H. Mueller, P. A. Beck, W. P. Chernock

PREFERRED orientation studies by Harris of rolled uranium rods indicated that hot rolling to a small reduction of area caused the (010) planes to become strongly oriented and the (110) planes weakly oriented perpendicular to the rolling direc- tion. The relative intensities of these two fiber texture components were reversed upon rolling to higher reductions of area. Cold rolling caused the (010) planes to become strongly aligned and the (130) planes weakly aligned perpendicularly to the rolling direction. The present investigation was undertaken to explore in more detail the effect on the rolling texture of variables, such as the penultimate condition, the final rolling temperature and reduction of area. In addition, the recrystallization texture of rolled uranium rods was also investigated.

Jan 1, 1959

By Charles Meyer

The year 1955 was a busy one for mining geologists, for the expanding world-wide business activity kept the demand for mining products generally high, stimulating operators to develop local ore reserves and to expand their efforts to find new deposits. The uranium rush was still on, although probably past its maximum rate of climb. Prospecting was also stimulated by the increasing demand for rare metals, and this created new and fascinating targets for exploration. On the whole, it was a boom year when the prospector's chronic optimism found few repressions.

Feb 1, 1956

By William E. Ford, Edward Salisbury Dana

The Nitrates being largely soluble in water play but an unimportant r81e i~ Mineralogy. SODA NITER. Rhombohedral. Axis c = 0.8276; rr" 1071 A 7101 = 73' 30'. Homeo- morphous with calcite. Usually massive form, as an incrustation or in beds. Cleavage: r (1011) perfect. Fracture conchoidal, seldom observable. Rather sectile. H. = 1.5-2. G. = 2'262.29. Luster vitreous. Color white; also reddish brown, gray and lemon-yellow. Transparent. Taste cooling. Optically -. w = 1'5874, e = 1'3361. Camp. - Sodium nitrate, NaN03 = Nitrogen pentoxide 63'5, soda 36'5 = 100.

Jan 1, 1922

By T. H. Miller

THE CHAIRMAN.-This session has to do largely with the question of specifications and conservation as regards secondary metals produced from scrap. We are all familiar with the many varieties of scrap metals and the astonishing number of secondary metals of various specifications produced from the treatment of those scraps. The impact. of the war on this industry has required a great many changes in the types of secondary metals produced from scrap, and in their utilization. In the short period available we cannot cover very much of this field, but we do hope to give you through the various papers a brief introduction to some of the principal problems. Mr. James S. Earle will present the first paper. Mr. Earle:

Jan 1, 1943

By AIME AIME

THE portrait of Herbert Hoover, President of the United States, recently painted by Philip A. de Laszlo at the request of the four Founder engineering societies, was unveiled at a special meeting in the Engineering Societies Building on Feb. 15. The portrait was delivered by Gano Dunn, chairman of the Hoover Medal Board of Award, who said, in part:,

Jan 1, 1932

Geological and Natural History Survey of Wisconsin, The University of Wisconsin, Madison, Wis - E. F Bean, State Geologist. A complete list of publications of this Survey will be sent upon request Only a portion of the Bulletins and Maps fall within the scope of this directory, and most of them are available They are: Bulletin 4, Building and ornamental stones of Wisconsin (1898), $2 50, 6, Preliminary report on the copper-bearing rocks of Douglas County, and parts of Washburn and Bayfield counties (1901), 50 cents, 7, The clays and clay industries of Wisconsin (pt 1) (1901), 50 cents; 14, Report on lead and zinc deposits of Wisconsin (the report is out of print but the 18 maps which accompanied it can still be had) (1906), 20 cents (a series of six maps, supplementary to these (1909), may be had for 6 cents), 15, The clays of Wisconsin and their uses (1906), 50 cents; 16, The geology of north-central Wisconsin (1907), $2, 17, The abandoned shore lines of eastern Wisconsin (1907), 50 cents, 19, Zinc and lead deposits of the Upper Mississippi Valley (1907), 25 cents; 34, The limestone road materials of Wisconsin (1914), 50 cents, 35, Underground and surface water supplies of Wisconsin (1915), $150, 36, The physiography of Wisconsin (new edition now in press) (1916), $125, 41, A study of methods of mine assessments and valuation (1914), 50 cents; 44, Mineral land classification in parts of northwestern Wisconsin (1915), $5, 45, The peat resources of Wisconsin (1915), 50 cents, 46, Mineral

Jan 1, 1933

By Colin MacDonald

The choices of an uranium mill flowsheet are pri- marily determined by economic feasibility with plant location and regulatory bodies playing a lesser but still important role in this determination. The host ore bodies will determine the leach pro- cess to be used for basic uranium extraction. Im- mediately following this decision, the method of leaching has to be determined. These can be: - Atmospheric leaching - Pressure leaching - In-situ leaching - Heap leaching The three previously stated criteria lay important parts in this decision. In the case of atmospheric or pressure leach and once the soluabilized uranium has been liberated from the host gang material, liquid solids separation becomes the major criteria. Three process flowsheets are available; they being: -Countercurrent decantation - Countercurrent or co-current filtration - Resin in pulp Following liquid solids separation, concentration and precipitation become the next variable choice. They being: -Solvent extraction - Fixed bed ion exchange - Fluid bed ion exchange Lastly, washing and drying of the precipitated product to remove impurities can be carried out by either filtration or centrifugation. With the exclusion of milling circuits, grinding circuits, flotation circuits, and calcining processes, we have 240 variations of the flowsheet between leaching and a dry washed precipitate. Of this total, filtration in one form or another and in single or multiple applied forms has application in 144 streams. This paper intends to discuss four (4) facets of the total flowsheet in which filtration is applied, following grinding and prior to calcining. They are: - Leached pulp liquid solid separation - Tailings dewatering - Pregnant solution clarification - Yellow cake washing and dewatering

Jan 1, 1980