Search Documents

By Nicholas J. Grant, Gordon D. Gemmell

CREEP rupture characteristics of high purity Al-Mg solid solution alloys were studied by Mul-lendore and Grant' to investigate solid solution strengthening of pure aluminum and the accompany- ing effects on deformation and fracture characteristics. This paper presents the results of an extension of that work to A1-Cu and Al-Zn alloys to permit a comparison of the relative effects of the three solute elements on the high temperature strength and on the deformation and fracture characteristics. Experimental Procedure A total of nine alloys was studied. They were all made of ultra high purity aluminum alloyed with high purity copper, zinc and magnesium. The corn-

Jan 1, 1958

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By Arthur F. Taggart

The following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.' Screen apertures used are the average apertures of testing screeps of the meshes given. i . Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill, Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversise reground in pebble mill, see Card 113. Feed to mill through 2-in. mesh. Mesh Feed, Per Cent. Discharge, Per Cent.. + 1in. 5.50 ....... + 3/4. 28.00 + in. 30.00 ...... + 1/4in. 19.72 ....... + 10 10.87 2.10 + 20 2.42 8.00 -20 3.51 .....,. + 40 ....... 22.68 + 60 ...___ 10.50 4-80 ....... 11.80 + 100 ....... 3.90 -100 ....... 40.15

Jan 1, 1916

By L. W. Kempf

THE thermal expansion characteristics of aluminum alloys have been examined by several investigators, among whom may be mentioned Shakespear,1 Schulz,2 Hidnert,3 Hidnert and Sweeney4 and McCullough.5 Shakespear compared the expansion of a series of aluminum alloys containing 14 per cent copper, with separate additions of about 1 per cent each of manganese, tin and zinc with that of pure copper. Schulz examined the expansion of aluminum and zinc and some aluminum-zinc alloys. Hidnert determined with a high degree of precision the expansion characteristics of pure aluminum, some aluminum-copper, aluminum-zinc, aluminum-silicon and some commercial alloys. Hidnert and Sweeney examined the expansion characteristics of aluminum-beryllium alloys. McCullough, by an interferometer method, determined the expansivity of some aluminum-copper, aluminum-magnesium, aluminum-iron, aluminum-nickel, aluminum-silicon and aluminum-manganese alloys. Incidental to an investigation carried out during the past six years and leading to the development and exploitation of an aluminum piston alloy of relatively low thermal expansivity, the expansion characteristics of a wide variety of alloys were examined. Some of the data which might be of general interest are gathered in this paper.

Jan 1, 1933

By R. Walker, R. J. Anslow

Today at Tampa we see the end results of a team effort: A vital link in an intermodal transportation system, the link that enables the unit-train concept to be employed with full effectiveness and the link that improves the economics of water transportation systems. Two new phosphate transfer complexes with a multi- million ton annual capacity are in operation in Tampa, Fla. Revolutionary in concept, these companion installations represent a total investment in the Tampa Bay area of $18.5 million.

Jan 1, 1970

By J. C. Fisher

THE following facts are reasonably well established concerning the influence of boron on the hardenability of steel:1-4 1—Boron does not appreciably influence the ther-

Jan 1, 1955

The first session of the Institute was held at the Smithsonian Institution, on Tuesday evening, February 22d. The members were welcomed to Washington and to the Smithsonian by Prof. Joseph Henry. President Holley responded to the cordial welcome of Professor Henry, and then read an introductory address on the subject of Technical Education. Following the discussion on President Holley's address the following persons, duly proposed and indorsed by the Council, were elected members and associates of the Institute : MEMBERS. Emile R. Abadie,. .. .. St. Louis, Mo. R. J. Anderson,.....Pittsburgh, Pa. Commander L. A. Beardslee,. .. Washington, D. O, Charles Bender,. .. .. New York City. Charming M. Bolton,. .. . Richmond, Va. Thomas E. Bowman,. .. . Silverton, Colorado. Calvin E. Brodhead,. .. . Bethlehem, Pa. M. L. Brosius,. .. .. . Lewistown, Pa. Harvey H. Brown,. .. .. Cleveland, Ohio. James A. Burden,.. .. . Troy, N. Y. J. P. Clemes,. .. .. . Sonora, Mexico. N. H. Cone,. .. .. . Nederland, Colorado. W. F. Durfee,.. .. . New York City. Robert Frazer, Jr.,. .. . Ashland, Pa, Joseph E. Galigher,.. .. . Bingham, Utah. William Golding,.. .. . Steel Works P. O, Pa. Samuel E. Griscom,.. .. . Pottsville, Pa. Gen. E. Burd Grubb,.. .. Beverly, N. J, Arthur R. Guerard,. .. .. Charleston, S. C. Edward Hart,.. .. .. Easton, Pa. Prof. Lewis M. Haupt,. .. . Philadelphia. E. S. Hawley,.....Buffalo, N. Y. John W. Hoffman,.. .. .. Philadelphia. Nelson P. Hulst,.. .. . Milwaukee, Wis. H. C. Humphrey,.. .. . Philadelphia. Ed. P. Jennings,.. .. .Ithaca, N. Y. B. F. Jones,......Pittsburgh, Pa.

THE first session of the Institute was held at the Smithsonian Institution, on Tuesday evening, February 22d. The members were welcomed to Washington and to the Smithsonian by Prof. Joseph Henry. President Holley responded to the cordial welcome of Professor Henry, and then read an introductory address on the subject of Technical Education. Following the discussion on President Holley's address the following persons, duly proposed and indorsed by the Council, were elected members and associates of the Institute : MEMBERS. Emile R. Abadie, - St. Louis, Ma. R. J. Anderson, - Pittsburgh, Pa. Commander L. A. Beardslee, - Washington, D. C. Charles Bender, - New York City. Channing M. Bolton, - Richmond, Va. Thomas E. Bowman, - Silverton, Colorado. Calvin E. Brodhead, - Bethlehem, Pa. M. L. Brosius, - Lewistown, Pa. Harvey H. Brown, - Cleveland, Ohio. James A. Burden, - Troy, N. Y. J. P. Clemes, - Sonora, Mexico. N. H. Cone, - Nederland, Colorado. W. F. Durfee, - New York City. Robert Frazer, Jr., - Ashland, Pa. Joseph E. Galigher, - Bingham, Utah. William Golding, - Steel Works P. O., Pa. Samuel E. Griscom, - Pottsville, Pa. Gen. E. Burd Grubb, - Beverly, N. J. Arthur R. Guerard, - Charleston, S. C. Edward Hart, - Easton, Pa. Prof. Lewis M. Haupt, - Philadelphia. . R. S. Hawley, - Buffalo, N.Y. John W. Hoffman, - Philadelphia. Nelson P. Hulst, - Milwaukee, Wis. H. C. Humphrey, - Philadelphia. Ed. P. Jennings, - Ithaca, N. Y. B. F. Jones, - Pittsburgh, Pa.

Jan 1, 1876

By W. G. Whildin

This paper will be confined to a discussion of the methods in use in the property of the Lehigh Coal and Navigation Co. in the Panther Creek valley.

Jan 1, 1915

By C. E. Lawall

WHEN this study was started very little information was available, regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to properly classify West Virginia coals.

Jan 1, 1932

By R. W. Raymond

By the death of Bergrath Prof. M. F. Gaetzschmann, which occurred on the 18th of February, in the 95th year of his age, at his lifelong home in Freiberg, Saxony, the Institute loses one of its earliest and most eminent honorary members, and the profession of mining and engineering one of its most influential and useful representatives,

Jan 1, 1896

By Stephen R. Holsinger

During 1972, Asarco's Silver Bell Unit embarked upon a project to test a digital computer-controlled grinding circuit against the performance of its other five grinding lines. The planning, implementation, and subsequent outcome of that project has been previously reported in a paper by Pitts 1, et al. This paper will describe the solutions to major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines. Changes made in operating philosophy and methods during the expansion will also be discussed.

Jan 12, 1978

By Stephen R. Holsinger

During 1972, Asarco's Silver Bell Unit embarked upon a project to test a digital computer-controlled grinding circuit against the performance of its other five grinding lines. The planning, implementation, and subsequent outcome of that project has been previously reported in a paper by Pittsl, et al. This paper will describe the solutions to major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines. Changes made in operating philosophy and methods during the expansion will also be discussed.

Jan 1, 1979

BOSTON LOCAL SECTION Executive Committee HENRY L. SMYTH, Chairman ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS ALBERT SAUVEUR Meets on the first Monday evening of each winter month, Twenty-third Meeting The Twenty-third Meeting of the Boston Local Section was held at the Engineers' Club, 2 Commonwealth Ave., on Monday evening, Nov. 30,- 1914. Prof. R. A. Daly addressed the meeting on The Iron Ores of Küruna; Sweden. AUGUSTUS H. EUSTIS Secretary.

Jan 1, 1915

By L. L. Anderson, R. E. Wood, W. H. Wiser

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70%of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than %in.) tubes and at reaction residence times of less than 10 secs. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1977

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5 to 2.9 lb CaS/lb Hg in the ore. Gold-to-mercury ratios of 100:l to 400:l were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1984

By Jack C. Bokros, Philip C. Rosenthal

DEVELOPMENT of the autoradiographic method in metallurgical research has been directed mainly toward gaining higher resolution, i.e., toward being able to locate segregation of a radioactive isotope on a finer scale. In the investigation reported, the liquid emulsion autoradiographic technique' used in the biological science was adapted to the autoradiography of metals. The distribution of carbon-14 in pure iron after various treatments was studied using this technique. Amorphous carbon uniformly labelled with carbon-14 at a specific activity of 6.95 microcuries per millimole was obtained from Tracerlab Inc. Carbon-14 emits P particles having a maximum energy of 157 kev and an average energy of about 50 kev. These ßs have a maximum range of about 30 mg per cm' and a half-thickness of about 3 mg per cm2. The iron used was spectroscopically pure electrolytic iron prepared by the Oak Ridge National Laboratory. Unhardened nuclear track emulsion, type NTB, was kindly supplied by the Eastman Kodak Co. This emulsion contains approximately 80 pct Ag halide,

Jan 1, 1957

Data about production in this state are very scarce, and with the exceptions of the years 1850, 1860, 1880 and the later years, the tonnages shown in Table 67 are estimates. [ ]

Jan 1, 1942