Search Documents

By E. G. De Coriolis

THE development of huge production facilities and of new or improved processes for manufacturing magnesium from its raw sources has been an outstanding achievement of this war. Furthermore, at least one new method has reached a stage of pilot production that offers promise. Its potentialities seem to indicate that a reduction in cost and simplification or elimination of problems incident to the use of at least one of the present processes are quite within the realm of possibility. Although magnesium of very high purity (99.9 per cent and higher) is obtained, and the rate of recovery reasonable (60 to 70 per cent), the ferrosilicon reduction process is open to a serious objection, which at the time its use was proposed was thought to be sufficient to raise some doubts as to its success, at least on a high production basis. The temperature range at which the reaction is carried out-namely, 2100° to 2150°F.-is very close to the failure temperature of the material of which the retort is made. It is so close that for a time it was assumed it might make commercial use of the process an impossibility. However, at the time under discussion, the demand for magnesium was so great that it was felt by those who had to go ahead and produce this essential metal that the emergency warranted their taking a chance on this process. Subsequent developments have fully justified the soundness of their decision. Fortunately for the war effort, when the plants were put into operation it was discovered that although the retorts did collapse in rather short periods of time, as predicted, they could be blown back into operable shape by application of high-pressure air. This practical method of operation so relieved the situation that the problem disappeared. Nevertheless, if the process had not been successful, or the production of magnesium by the electrolytic process had not been able to keep pace with demands, our war program would have been seriously impaired. "FIRELESS COOKER" PROCESS For this reason a program was set up and assigned for the development of a new method that had been suggested to the War Production Board in 1941. It is believed justifiable in terming the method "new" for several reasons: (1) while utilizing the same (ferrosilicon) process as the Pidgeon, hence involving similar reactions, the type of retort or furnace is essentially different, (2) the method of operation, reaction temperatures, etc., differ materially, and, most important of all, (3) the problems to be overcome in making the process successful were not and could not have been anticipated by anything previously known about the Pidgeon process. As will be shown later, the briquetting process, the condenser, the furnace lining

Jan 1, 1945

By J. G. LECKIE

During the first ten months of 1943 copper was produced at a higher rate than in 1947. However, on Oct. 24 one of the large mines was shut down due to a strike. As of Dec. 31 the strike was still in effect and had already resulted in a loss of production of 50,000 tons of copper. The demand for copper was considerably greater throughout the year than the supply. The price of electrolytic copper delivered at the Atlantic Seaboard refineries advanced from 21.20 to 23.20 cents per lb during the year. This sustained demand for copper, together with the increase in price, has had the natural effect of spurring interest in uncovering new deposits, and in re-examination of known low-grade deposits and old tailing clumps. This is in addition to the usual reevaluation activities which normally result from the constant improvements in efficiency of ore concentration.

Jan 1, 1949

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By Walter Mathesius

The use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100" F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible ' to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800" and 1,000" F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available. In an endeavor to obtain results, even with inadequate equipment, we find that, at many plants, the stoves are worked far beyond their capacity. This leads, in many instances, to a situation in which the coke saving in the

Jan 1, 1915

By J. S. Bowles

THE martensite transformation in lithium, dis- covered by Barrett,' has been studied extensively by X-ray techniques by Barrett and Trautz,² and Barrett and Clifton.V he present paper reports the results of an investigation into the metallographic characteristics of lithium martensite. Such an investigation has not been carried out before. The spontaneous transformation in lithium consists of a change from a body-centered cubic to a close-packed hexagonal structure with the hexagonal layers in imperfect stacking sequence." As far as is known at present, this transformation can be regarded as being crystallographically equivalent to the body-centered cubic to close-packed hexagonal transformation that occurs in zirconium,5 although stacking errors have not been reported in zirconium. From a study of the orientation relationships in zirconium, Burgers5 as proposed that the martensite transformation, b.c.c. to c.p.h., occurs by a heterogeneous shear on the system (112) [111]. The crystal-lographic principle underlying this proposal is that the configuration of atoms in the (112) plane of a b.c.c. structure is exactly the same as that in the (1010) plane of a close-packed hexagonal structure based on the same atomic radius. The pattern in 2v2 both these planes is a rectangle d X 2v2d where v3 d is the atomic diameter. Thus a close-packed hexagonal structure can be built up from a body-centered cubic structure by displacing the (112) planes relative to each other.* This mechanism leads to orientations that can be described by the relations: (110)b.c.e. // (0001)c,p.h.; [111]b.c.c. // [1120]c.p.h Observations confirm these relations. In zirconium, Burgers' measurements indicated an angle of 0" to 2" between the close-packed directions, while Barrett's measurements on lithium indicated an angle of 3". According to the Burgers' mechanism, the martensite habit plane for this transformation would be expected to be the (112)b.c.c. plane, for this plane would not be distorted by the transformation. One of the purposes of this investigation was to find out whether the observed lithium habit plane agrees with this prediction of the Burgers' mechanism. Experimental Procedure Materials: The lithium was from the same purified ingot used by Barrett and Trautz.² The Bridgman technique was used to produce single crystals. To maintain a temperature gradient in the melt, during the production of these crystals, it was necessary to use a steel mould with a wall thickness of only 0.015 in. Metallographic Techniques: Lithium specimens could be given an excellent metallographic polish by swabbing them gently with cold methyl or ethyl alcohol.? The best results were obtained with methyl alcohol saturated with the reaction product, lithium alcoholate. With higher alcohols the reaction became progressively slower and the attack became an etch pit attack rather than a polish attack. Butyl and amyl alcohols were used for macroetching. After polishing, it was necessary to remove all traces of alcohol from the specimens; otherwise, on subsequent quenching in liquid nitrogen, the alcohol froze to a glassy film. The alcohol was removed with dry benzene. The benzene in turn had to be removed before quenching, but since it does not react with lithium it could be allowed to evaporate. The specimens could then be quickly quenched before they began to tarnish. This operation could be carried out in air on all but excessively humid days when it was advisable to use an atmosphere of dry nitrogen or argon. For examinations at room temperature, the specimens could be transferred directly from the benzene bath into a bath of mineral oil. In mineral oil the specimens oxidized slowly by the diffusion of oxygen through the oil but the structure remained visible for about an hour. Lithium Martensite: Specimens prepared in the manner described above transformed spontaneously to martensite with an audible click when quenched into liquid nitrogen; i.e., M, was above the boiling point of nitrogen (77°K). The disparity between this result and the M, temperature of 71°K, found by Barrett and Trautz, is probably to be attributed to the large grain size and freedom from mechanical deformation of the specimens used in the present work. The relief effects produced by the transformation did not disappear when specimens were quenched from liquid nitrogen into mineral oil at room temperature. This permitted the microstructures to be studied at room temperature where, of course, the martensitic phase was no longer present. Typical micrographs of lithium "martensite" made at room temperature are reproduced in figs. 1, 2, and 3. As anticipated by Barrett and Trautz, the microstruc-

Jan 1, 1952

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Wanted for a mill on the Ivory Coast of Africa an experienced amalgamator and millman. Salary, $160 to $200 per month. No. 18. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Chemist-metallurgist of broad technical training, university graduate, with experience in chemical and metallurgical research work, desires position, preferably in the East. Has successful past that stands investigation. No. 73. Member, mining and metallurgical engineer; thorough technical training, Ph.D., Columbia University, aged 39, married, with-an-extensive experience in smelting, mining, and economic geological work in U. S., Mexico, and South America, desires position as assistant to the Manager or Superintendent, or as a director of experimental and research work, with a reliable mining or metallurgical company. The West, Mexico, or South America preferred. No. 98.

Jan 6, 1914

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.'s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979

By J. W. Mills

This paper's aim is to demonstrate, by reviewing findings and conclusions of earlier authors and through recording and interpreting the outcome of recent laboratory study of the ores, that the ores around the Gem stocks are metamorphosed equivalents of common siderite-sulfide ores far from the stocks, as was first proposed by Hershey (1912, 1913). That is, all the ores probably have the Precambrian age of 1250 million years reported by Long et al. (1960). Those near the Gem stocks, however, were extensively metamorphosed in Cretaceous time during the emplacement of stocks so their resemblance and relation to other veins in the district are camouflaged.

Jan 1, 1985

By Carl Scholz

DURING November And December, 1907, Four Serious Mine-explosions Occurred In The Appalachian Coal-Field, Which Resulted In The Loss Of Nearly A Thousand Lives And Caused An Enormous . Damage To Property. These Accidents Attracted More Than The Usual Attention; Coal-Trade And Engineering Papers Contained Many Comments And Suggestions On The Cause And Prevention Of Accidents; The Daily Press In Many Instances Condemned The Coal-Operators And Charged These Accidents To Their Negligence, Or Their Anxiety To Make Money Without Adopting Precautionary Measures. Immediately After Each Accident The Respective State ..Authorities Ordered Close Investigations To Be Made, With The View Of Establishing The Cause And Suggesting Remedies To Prevent Recurrence. Representatives Of The Technologic Branch Of The U. S. Geological Survey, To Whom The Investigation Of Mine-Accidents Had Recently Been Delegated By The Secretary Of The Interior,. Visited The Mines And Co-Operated With The Local Authorities In Their Determinations. It May Be Safe To Say Here That An Investigation Of A Mine After An Explosion Has Occurred Discloses But Little, Because. The Causes Have Been Removed And Conditions Have Been Entirely Changed. On Jan. 8, 1905, The Coal-Operators Of West Virginia Organized An Association At Washington For The Purpose Of Making Extensive Investigations, And Sufficient Funds Were Pledged To Carry Out This Work. At This Organization Meeting, The Representatives Of The Geological Survey Present Had No Suggestions To Offer As To The Cause Of These Accidents. An Examination Of The Various Reports Concerning These Accidents Indicates That The Explosions Were Caused By The Ignition Of Gas Or Dust; They Show The Point Of Origin And The Direction In Which The Force Was Expended, And Give A Detailed Description Of The Damage Done. Very Little Has Been Said As To What

Jan 7, 1908

By George E. Roberts

The maintenance of the common gold standard is the most important cooperative undertaking in the world. The war broke up this relationship and brought about a state of great disorder in the currencies and exchanges. After the war the countries all began to grope their way back to the gold standard as the best means of establishing trade and financial relations with each other. With this movement began a general decline in commodity prices. The question has been raised whether the world's return to the gold standard was not forcing prices back to the prewar level. Also, the question is raised whether the world has not outgrown the supply of gold as the basis of credit. Because Europe readjusted its monetary units to conform to the higher level of prices there is no pressure on prices on this account. Furthermore, a large amount of gold formerly in hand-to-hand circulation passed out of circulation and has been added to the central bank reserves. The gold reserves of 36 countries increased approximately 100 per cent from the outbreak of the war to June 30,1930. The increase is much larger than the average increase of prices in any of the important countries, at any time since 192.5. As gold in the central banks of issue is far more effective for all business purposes than gold in circulation, the gold scarcity argument has little basis as applied to this time. The abnormal distribution due to the war was to the disadvantage of business everywhere. Credit was scarcer and dearer in some countries. The inflation in this country might have been greater had the production of gold been greater. The argument supporting the theory of a scarcity of gold assumes as fundamental that general price changes must be accounted for by changes in the price equation on the side of money. This is disproved in every period of business depression. A downward price movement is characteristic of every period of business recession. Important discoveries of gold must be made even to maintain present gold production, in the face of which the world's business is bound to continue increasing. It cannot be doubted that some way will be found

Jan 1, 1931

By AIME AIME

WEST TEXAS, New Mexico and Northern Mexico form one of the most interesting regions in America for geologists and mining men and are full of points of historical and human interest for others. Including as the region does, a representative portion of the high plateau of Mexico, the front range of the Rocky Mountains and the great down-dropping plains of Texas, there is variety as well as interest in the geological and mining problems there to be studied. Gold and silver mining were the pioneer industries and are yet of high rank in importance. Among the papers to be presented at the El Paso meeting of the Institute this month will be two dealing with silver mining and ore treatment at the Shafter mine in Texas, that most un- usual property which has for so many years been the largest mining enterprise in its region. West Texas is now better known for its petroleum and gas, and in another paper will be described the problems involved in uding natural gas for smelting at the well-known El Paso smelter of the American Smelting and Refining Co. In still other papers, presented at the session sponsored by the West Texas Geological Society and cooperating organizations, the general geology of the region, the potash and the sulfur deposits will be de- scribed. At El Paso the refineries of the great com- panics will be available for visits.

Jan 1, 1930

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of' 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 ' and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By D. B. McDyre

THE object of this study was to compare variations in slag volumes with tap changes while maintaining all other factors constant. This meant: 1. Same type of heat (Spec. SAE 1030). 2. Same charging material (3500 lb foundry, 4000 lb bought scrap). 3. Same amount of sand by weight to fix slag line. 4. Same method of melting with the exception of tap changes. 5. Same method of weighing slag after each test. The equipment of the Dodge Steel Co. consists of a 132-ton Heroult furnace lined with silica brick, using three 8-in. electrodes and a 2000-kva transformer, with four tap changes. In the melting practice we use a Fischer Carbanalyzer and a Herty viscosimeter and try to standardize all heats by making necessary carbon and slag adjustment before boil to keep all heats as uniform as possible.

Jan 1, 1947

By L. M. Pidgeon, W. Curlock

FREE energies of formation of zinc sulfide and magnesium sulfide had previously been estimated to an accuracy of ± 5.0 kcal per g mol. In the present work, these values were determined experimentally. As the determinations of the free energies of formation of zinc sulfide and magnesium sulfide presented different problems, separate experimental procedures were employed for each. ZINC SULFIDE It is difficult to measure the free energy of formation of either zinc sulfide or magnesium sulfide by measuring their decomposition pressures directly, as they are very stable compounds. An attempt was made by Jellinek and zakowski3 to study the equilibrium. zns(s) + H2(g) = Zn(g) + H2S(g) [I] They passed hydrogen over zinc sulfide and analyzed the gases leaving the reaction zone for H2S. They were unable to determine the true partial pressures of the H2S by this method, as some of the H2S on being cooled from the reaction temperature, reacted with the zinc in the gas to produce ZnS. Consequently, they were unable to establish any true equilibrium data for reaction [I]. More recently,' the equilibria ZnS(sphaledte) + Fe (s) — FeS(s) + Zn(g) [2] and ZnS(sphalerite) + 2Cu(s) — Cu2S(S) + Zn (g) [3] were studied. As the standard free energy of formation of Cu2S is known to * 3.0 kcal, and of FeS to ± 1.0 kcal, it should be possible upon performing equilibrium studies on reactions [2] and [3] to deduce the standard free energy of formation of ZnS (sphalerite). However, as both of these equilibria involve 2 solid sulfides, and as it is possible for these sulfides to dissolve in one another, it is necessary first to ascertain the activities of the various sulfides in these solid phases.

Jan 1, 1959

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By A. L. Sweetser

EXPERIENCE has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorination-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave : Fe2O3, 3.35; FeS, 1.5; MnO2, 0.75; ZnCO3, 4; Al2O3, 3.20; H2O, 0.7; SiO2 and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, .and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size-a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Sep 1, 1907

By George M. Rigg, Samuel M. Cassidy

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947

By Samuel M. Cassidy, George M. Rigg

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947