Search Documents

By William Loblowitz

A simplified system of flotation testing has been developed recently at the Bureau of Mineral Research of Rutgers University. The technique involves the known principle of skin flotation and can be used with minute quantities of sample and reagents in a beaker. A vessel containing the conditioned sample with added water and flotation reagents is held inclined and rotated slowly. Water-repellent particles come in contact with air and float on the surface of the liquid, while wettable particles are submerged. The float is poured off and filtered whereas the nonfloat remains in the beaker. The filtrate may be returned to repeat the process.

Jan 6, 1951

By P. B. Baxendell, R. Thomas

Work on the calculation of vertical two-phase flow gradients by Cia. Shell de Venezuela has been based mainly on the "energy-loss" method proposed by Poett-mann and Carpenter in 1952. The "energy-loss-factor" correlation proposed by Poettmann and Carpenter was based on relatively low-rate flow data. This correlation proved inapplicable to high-rate flow conditions. In an attempt to establish a satisfactory correlation for high rates, a series of experiments was carried out at rates up to 5,000 BID in Cia. Shell de Venezuela's La Paz field in Venezuela, using tubing strings fitted with electronic surface-recording pressure elements. As a result of these experiments a correlation between energy-loss factor and mass flow rate was established which is believed to be applicable to a wide range of conduit sizes and crude types at high flow rates (e.g., above 900 BID for 27/8-in. OD tubing). It is anticipated that the resulting gradient calculations will have an accuracy of the order of % 5 per cent. At lower flow rates the energy-loss factor cannot be considered as constant for any mass rate of flow, but varies with the free gas in place and the mixture velocity. No satisfactory correlating parameter was obtained. As a practical compromise for low flow rates, a modification of the curve proposed by Poettmann and Carpenter was used. In practice this was found to give gradient accuracies of approxirnately ± 10 per cent clown to flow rates as low as 300 B/D in 27/8-in. tubing. INTRODUCTION Production operations in Cia. Shell de Venezuela's light- and medium-crude fields are principally concerned with high-rate flowing or gas-lift wells. Under these conditions the analysis of well performance, the selection of production strings and the design of gas-lift installations are vitally dependent on an accurate knowledge of the pressure gradients involved in vertical two-phase flow. Initially, attempts were made to establish the gradients empirically as done by Gilbert,' but the results were not reliable due to scarcity of data over a full range of rates and gas-oil ratios. Several methods of calculation based on energy-balance considerations were attempted, but the computations were cumbersome and the results cliscouraging. In 1952 a paper was published by Poettmann and Carpenter' which proposed a new approach. Their method was also based on an energy-balance equation. but it was original in that no attempt was made to evaluate the various components making up the total energy losses. Instead, they proposed a form of analysis which assumed that all the significant energy losses for mutiphase flow could be correlated in a form similar to that of the Fanning equation for frictional 1osses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The basic method was applied in Venezuela to the problem of annular flow gradients in the La Paz and Mara fields" This involved establishing a new energy-loss-factor correlation to cover high flow rates and, also, some adaptation of the method to permit mechanized calculation using punch-card machines. The final result was 1 set of gradient curves for La Paz and Mara conditions which proved to be surprisingly accurate. With the encouraging results of the annular flow calculations, several attempts were made to obtain a corresponding set of curves for tubing flow. Here, unfortunately, little progress could be made. The original correlation of Poettmann and Carpenter was based on rather 1imited data derived from low-rate observations in 23/8- and 27/8-in. OD tubing. It did not cover the higher range of production rates, and extrapolation proved unsuccessful. A new correlation covering high flow rates was required, but this proved to be extremely difficult to establish since tubing flow pressure measurements at high rates did not exist—due to the difficulty of running pressure bombs against high-velocity flow. The necessity for reliable tubing flow data increased with the development of the new concessions in Lake Maracaibo, where high-rate tubing flow from depths of 10,500 ft became routine. Thus. it was decided to set up a full-scale test to establish a reliable energy-loss factor for tubing flow conditions. A La. Paz field light-oil producer with a potential of approximately 12,000 B/D on annular flow was chosen. To obtain full pressure gradients, a special tubing string was installed which was equipped with electronic surface-recording pressure measuring devices,

By H. A. Stacy

THE ability of galvanized sheet steel to withstand severe bending is of very great importance as relates to all such sheet material which, in service, is not used in the flat condition in which it is purchased. A "bend-test" clause is found in, all specifications for material of this kind. In the attempt to draw up a specification for galvanized sheet steel the subcommittee of the Federal Specifications Board having this work in charge, soon found that there was a surprising lack of published data and apparently very little available from manufacturing sources upon which to sustain or reject the various requirements embodied in the tentative specification which, in turn, had been based largely upon other specifications submitted to the subcommittee for this class of material. Specifications from 25 sources were received; 10 Government specifications, 10 from private users of such material, and five from manufacturers. The main points raised were: (1) The minimum mandrel thickness, expressed in terms of the thickness of the sheet tested, over which sheets with different weights of coating can be bent 180°, without serious damage to the coating; (2) the minimum radius of curvature on the inside of the angle in 90°-bends in such material; (3) effect of double seaming on the coating; (4) uniformity in the thickness of coating over a sheet, particularly as relates to the results of bend tests. In view of the uncertainty existing, it was considered very desirable for the subcommittee to conduct a series of tests in order to secure reliable information.

Jan 10, 1926

By Noel Stearn

WHEN the Age of Machinery was suddenly thrust upon civilization about the beginning of the nineteenth century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny pros-pectors. Thus in the countries now reasonably ac-cessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses" of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stu-pendous capital outlays involved in mining, develop-ment, and conversion operations, have resulted in excep-tional activity in three different fields of effort. The first is purely geographic. Prospectors are now pene-trating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores to find methods of recovering valuable metals from common substances. In the third field of effort. lie the activities of the economic geologist and the mining engineer, who en-deavor to locate concealed ore deposits, which would remain hidden from the prospector, no matter. how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract-a knowledge of certain fundamental princi-ples and processes involved in the origin, occurrence, structure, and distribution of deposits. of natural re-sources and of the rocks which form the environments of those deposits, and a process-of reasoning by analogy supplemented by the .use of the diamond drill, or such artificial exposure as the test pit, trench, shaft or tunnel. His primary efforts are usually bent on acquiring a knowledge of the distribution of the rocks-as accurate -is possible-which is a natural prerequisite to any conclusion as to how they became so distributed. Over very extensive areas, however, he meets. the extreme difficulty of being unable to see the rocks, except at rare intervals, since .they have been concealed by an overburden of glacial material, of alluvium, of soil, or of other rocks.

Jan 9, 1928

By A. J. de Witte

It has been observed that upon invasion of a sand containing oil or gas and connate water by mud filtrate the hydrocarbons are more rapidly flushed by the filtrate than is the connate water.' In time, it appears that the following displacement pattern emerges: oil (or gas) is being swept ahead by connate water which, in turn, is pushed by invading fluid. Eventually the connate water may have "banked up" sufficiently to form a zone of appreciable thickness leading the invading front. In the extreme case, Fig. 1 shows how the situation will develop.' Immediately adjacent to the borehole (radius r) there is a zone, the invaded zone proper, where the connate water has been flushed out completely and which contains only residual oil or gas and mud filtrate. This zone (extending out to a radius ri) grades more or less abruptly into the next (thickness A), which contains only residual hydrocarbon and connate water. Beyond it, again more or less sharply bounded, extends the virgin formation with the original interstitial water saturation Sw. The various saturations are indicated in Fig. 1. The three zones generally will be marked by resistivity contrasts owing to their different fluid contents. As the connate water is usually more saline than the invading fluid, the second zone having a high connate water saturation forms a concentric cylindrical ring or annulus of low resistivity R, around the borehole.',' It will be referred to as the "low zone." Fig. 1 shows schematically the resistivity profile. It is clear that the phenomenon of a low zone could not occur in invaded water sands. The presence of a low zone, therefore, would be a qualitative indication of a hydrocarbon-bearing formation. Granted that the phenomenon is real, if it were pronounced enough to be detected, one might thereby have a means of locating oil or gas in the ground. This is the aim of the "displacement logging" method.' In any case, the presence of a low resistivity zone will affect the reading of electric logs. Using conventional log interpretation techniques, one must be aware of this and, if necessary, correct for it. Whether correction or detection should be the goal will depend primarily on the magnitude of the effect. The type of log which is likely to be affected most is the induction log. The current pattern of an induction log is concentric with the borehole. Any concentric ring of low resistivity, therefore, will tend to become crowded by current lines. This zone of maximum current density will obscure the relative contributions to the current conduction by other portions of a bed making, for instance, the contribution of the virgin formation less significant and thus detracting from the value or the induction log as an R, reading device. The present note is intended to ascertain the maximum possible effect of a low zone in the extreme case portrayed by Fig. 1 on three commercially available types of induction logs, sc., 5 FF 27, 5 FF 40 and 3 F 60. Type 5 FF 27 or 5 PF 40 is currently run in conjunction with a 16 in. normal and SP log. This combination is gradually replacing the regular electric survey (two normals and one lateral) as a standard log in many areas. On the basis of the scheme of Fig. 1 (sharp boundaries between successive zones), the thickness of the low zone may be computed for various amounts of infiltration measured by the ratio of invaded zone diameter to hole diameter D,/d. Referring to Fig. 1, we can set up a material balance for the water displaced from the invaded zone proper and the water present in the low zone. The volume of connate water displaced from invaded zone upon flushing by mud filtrate is: V1 = e p (r2 - r2) ? Sw . where c = bed thickness ? = porosity Su, = original connate water satu-ration. The volume of water finally accu-mulated in the low zone is: Vz = e p [(r1 -?)2 - r2 4] ? Sw . where SW1 = 1 — Sor = "water" saturation in the invaded and low zones both. The volume of water originally present in the low zone is:

Jan 1, 1958

By R. G. Knickerbocker

A STURDY and consistent expansion of the metal industry occurred in 1947 exemplified by an increase of approximately 30 per cent in steel consumption over 1946. For this major reason, ferroalloy metals have seen their most useful and important peace-time year. The current domestic rate of consumption of high-grade ferroalloy ores, together with added consumption of new foreign producers as well as for eign nationals' restrictions on high-grade exports, makes very evident the increasing difficulties of obtaining sufficient high-grade ores. This accentuates the need for new and less expensive methods of production of ferro-alloy metals of higher purity from lower-grade domestic resources. As an important factor in preparedness, procurement of these high-grade, -critical ferroalloy minerals and metals for our nation's stock piles is a most important task. Also, this stock-piling can be the means of supplying incentive for the industrial development of the new metallurgical processes and plants necessary for the recovery of ferroalloy metals from our domestic low-grade deposits.

Jan 1, 1948

By R. W. Jigins

OPERATIONS of the Braden Copper Co. are in the Chilean Andes, southeast of Santiago. Most remote of the company communities is Sewell, a town of 12,000 people, 7000 ft above sea level at the junction of the Coya and Teniente rivers. Four miles down the Coya River is the smelter town of Caletones, elevation 4500 ft, with a population of about 3000. At the junction of the Coya and Cacha-poal rivers 24 miles below Sewell is Coya, elevation 2500 ft, location of the company's two hydroelectric plants. The principal accounting offices; steel, iron, and brass foundries; railroad shops; and major mechanical repair and fabricating shops are at Rancagua in the central Chilean valley, 44 miles from Sewell. The company owned narrow-gage railroad connects with the Chilean national railroad at Rancagua and above Coya is the only modern means of travel. El Teniente mine at Sewell is the largest underground copper mine in the world. The mill, at the portal of the main tunnel, has a capacity of 34,000 tons of crude ore daily, although production is lower during the winter beacause of electric power restrictions. When operating at capacity the mill produces 2000 tpd of copper concentrates and 32,000 tpd of tailings. Tonnage of tailings is equivalent to about 100,000 tons of pulp at normal water to solid ratio. Because the streams flowing from the Andes in the area of Braden's operations are used for irrigation, it is impossible to dump tailings directly to the river. The tailings pulp must be separated into solids and decanted clear water, and the clear water returned to the same water shed from which the original water was removed. Remaining sands and slime must be deposited in a reservoir where they will not cause trouble to farmers.

Jan 1, 1958

By Ian Campbell, G. Austin Schroter

Although there is now an extensive literature on the bleaching clays, not a great deal of material is to be found concerning the geological features of these deposits and their bearing on problems of exploration and development. At the same time, chemical and crystallographic research on the clay minerals during the past few years has laid a suitable foundation upon which to base conclusions of economic value drawn from field observations. All of the criteria and deductions herein presented are based upon extensive field work by the senior author, both in the United States and Canada, and when .subjected to the ultimate tests of development and exploitation they have held up remarkably well, despite the fact that many of these conclusions apparently have not been reviewed in the literature heretofore. The nomencelature of the bleaching clays is rather confusing in the light of present-day commercial standards and has even led to litigation.'" The old term "fuller's earth" is largely based upon trade usage and the definition of the term therefor? is dependent upon the changing standards of commerce. For statistical purposes the Bureau of Mines8' classes as "fuller's earth" all natural bleaching or filtering claylike materials that possess high adsorptive capacity without previous chemical treatment or activation. Conversely, the so-called activated or acid activated clays are now generally recognized as any clay mineral or mixture of the clay minerals whose adsorptive capacity has been developed to commercial standards by chemical or physical treatment. Therefore, without attempting to propose any additions to the nomenclaturc: of bleaching clays, this paper will refer to naturally adsorptive clays and activable clays, respecbively, for the two types indicated.

Jan 1, 1942

By G. Austin Schroter, Ian Campbell

Although there is now an extensive literature on the bleaching clays, not a great deal of material is to be found concerning the geological features of these deposits and their bearing on problems of exploration and development. At the same time, chemical and crystallographic research on the clay minerals during the past few years has laid a suitable foundation upon which to base conclusions of economic value drawn from field observations. All of the criteria and deductions herein presented are based upon extensive field work by the senior author, both in the United States and Canada, and when .subjected to the ultimate tests of development and exploitation they have held up remarkably well, despite the fact that many of these conclusions apparently have not been reviewed in the literature heretofore. The nomencelature of the bleaching clays is rather confusing in the light of present-day commercial standards and has even led to litigation.'" The old term "fuller's earth" is largely based upon trade usage and the definition of the term therefor? is dependent upon the changing standards of commerce. For statistical purposes the Bureau of Mines8' classes as "fuller's earth" all natural bleaching or filtering claylike materials that possess high adsorptive capacity without previous chemical treatment or activation. Conversely, the so-called activated or acid activated clays are now generally recognized as any clay mineral or mixture of the clay minerals whose adsorptive capacity has been developed to commercial standards by chemical or physical treatment. Therefore, without attempting to propose any additions to the nomenclaturc: of bleaching clays, this paper will refer to naturally adsorptive clays and activable clays, respecbively, for the two types indicated.

Jan 1, 1942

By DR. RICHARD RATHBUN

(Washington Meeting, May, 1965.) THE remarks of Dr. Rathbun in his address of welcome render it unnecessary that I dwell either upon the history or aims of the National Museum, and enable me to proceed at once with a brief descriptive outline of the Department for which I am responsible, and this with particular reference to that division devoted to applied geology. The amount of geological material brought together prior to 1876, under the various Congressional acts quoted, was, though valuable, comparatively small. It consisted mainly of the collections made by Professor J. D. Dana and his assistants during the Wilkes Exploring Expedition; by the various geologists accompanying the surveys of the Pacific railroads in 1854-55; the Surveys West of the 100th Meridian under the direction of the Engineering Corps of the Army; the United States geological surveys under direction of Dr. F. V. Hayden ; and the various Land Office surveys. Prior to 1873 there were no paid assistants to care for these collections. They were studied, if studied at all, by " collabrators," so-called, several of whom had offices and even sleeping apartments in the Smithsonian Institution. In the list of these collaborators are found such names as Conrad, Cope, Gabb, Leidy, Lesquereux, Meek, and Newberry. The building now occupied by the National Museum was designed primarily to make room for the great mass of material secured in 1876 at the close of the Centennial Exposition in Philadelphia. As completed in 1880, it afforded opportunity for expansion and incidental organization on much more practical basis than had previously existed. This found expression in the creation of numerous departments with salaried officials to take charge of the various collections. With the appointment of Dr. George W. Hawes to the position of Curator of Geology and Mineralogy, in 1881, and Dr.

Jul 1, 1905

By H. S. Coe, G. H. Clevenger

Engineers have long recognized the desirability of correlating the data obtained from small-scale slime-scttling tests with commercial work as carried on in large tanks. This need, though most apparent in designing new installations, frequently arises also in existent plants, since a large range of experimental work can be performed without interfering with regular operation. General Settling Phenomena In order to develop rational methods of laboratory testing, it becomes necessary to study the general phenomena of settling. Since it was desired to give the public the benefit of these methods at as early a date as possible, together with the knowledge of the general principles of slime settling necessary for a clear understanding of the laboratory tests, we have ventured to discuss the subject in so far as brought out by the work which we now have under way. We realize that certain of our preliminary conclusions may be subject to modification, but it seems probable that, with but few exceptions, the general laws enunciated will cover the settling behavior of all pulps encountered in metallurgical plants. However, it must be recognized that there is still a vast amount of work to be done upon certain phases of the subject; therefore, at this time we will attempt only a discussion of the behavior of ore pulps during the process of settling or dewatering, under certain given conditions. The laws and principles controlling these conditions are not fully established, so that a complete discussion of them will not be attempted in this paper. In metallurgical practice, slime pulp consists of water, finely divided sand

Jan 1, 1917

By John K. Hammes

INTRODUCTION This introductory paper presents a description and definition of what the finance function is and what it specifically means for the mining industry. In its simplest terms, finance is, "management of money matters". As an area within the discipline of business administration it draws heavily on the related fields of economics and accounting, and to a lesser extent on marketing and production. MINING FINANCE DEFINED In preparing to write about what finance means to the mining industry, I asked a number of mining people the question, "What does mining finance mean to you?" Most responded that mining finance was "How a company borrowed money for mine development", and perhaps half those questioned included "raising equity" in the definition. It is not surprising that the mining industry concept of finance is the providing of funds needed for the objectives of the business, for that was once a view shared by authorities in the field of business administration. Further, it is certainly the area where much of the emphasis has been placed in the past ten to fifteen years as the industry struggled with the development of more remote and more refractory or lower-grade orebodies while profitability and internal cash flow were below expectations. No wonder project finance became such a popular topic. Twenty years ago it is probable that the emphasis would have been on mine valuation, for that subject was the area of finance then most often examined in industry publications. Papers concerning the pros and cons of payback, internal rate of return, and discounted cash flow appeared regularly. Let's examine the following situations, each the result of a financial decision: - Funding the exploration program in a developing country was accomplished by buying the next six-months budget needs in local currency. One week later the currency devalued 30 percent. If the purchase had been delayed or the local currency borrowed short term, a substantial saving would have been made in funding the program. - A major mining company borrows heavily to finance both expansion of its primary mining business and its entry into several new industry segments. When markets for all of the commodities it produces turn down for a prolonged period, there is concern over the adequacy of cashflow to cover debt service in addition to other company needs. The company's financial officers, however, had arranged very large committed credit facilities from numerous financial institutions which assured the availability of funds for several years. This enabled the company to implement a strategy to conserve cash, sell assets and survive until conditions improved. Further, short term suppliers of credit also were comfortable with the assurance that longer term credit was there to support them. -A medium size mining company financed several mines independently with limited obligations on the part of the parent company. The company decided to refinance the operations under one agreement. More flexible terms, lower interest cost and a longer tenor financing were achieved in return for assuming the risk as a direct obligor. - The exploration and development group of a large mining company proposes to develop a new mine in a country in which the company does not presently operate. When the investment is rejected they are advised that one reason was that the reinvestment assumption inherent in the discounted

Jan 1, 1985

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

By Samuel M. Dunaway

INTRODUCTION ASARCO Incorporated purchased the East Tennessee Zinc Mines of the American Zinc Company and commenced operating on November 29, 1971. Presently, three mines are operating producing 6620 t/d (7300 stpd). The ore mined is sphalerite which occurs In lower Ordovician carbonates of the upper Knox Group and occurs in open space and fracture filling. Orebodies range from 3 to 46 m (10 to 150 ft) thick with dips from flat to 20º. The mining method is random room and pillar modified by shrinkage and bench stoping. Like other mining departments, the mining group at the Tennessee Mines Division is constantly looking for methods to improve productivity and safety and to reduce mining costs. This involves testing new equipment, trying new ore extraction ideas and making mining plant alterations to meet changes in operating conditions. The areas of change that will be described in this paper are longhole raising, jumbos and LHD loading, shaft sinking, conveyor transport of ore and sublevel haulage developments. LONGHOLED RAISES Raise driving has always been a hazardous occupation for miners and today it is becoming more difficult to get competent people for this kind of work. This problem has led us to seek an easier, safer way in which to excavate raises. The first longhole raises were excavated in the early 1970&apos;s using a Gardner-Denver air trac equipped with a PR-123 rock drill. The machine used 38 mm x 244 cm (1 ½ in x 8 ft) round rods with rope

Jan 1, 1977

By A. L. Lee, M. H. Gonzalez, R. F. Bukacek

Experimental viscosity data for methane are presented for temperatures from 100 to 340F and pressures from 200 to 8,000 psia. A summary is given of the available data for methane, and a comparison is presented for that data common to the experimental range reported in this paper. Correlation of the data is presented, and predicted values are given for temperatures up to 460F and pressures up to 10,000 psia. INTRODUCTION The increasing ranges of temperature and pressure at which fluids are produced, transferred and processed in the petroleum and chemical industries stress the need for accurate information on physical properties, both for engineering calculation and for improving the methods used to estimate physical properties. A survey of the literature reveals that disagreements between published data on the viscosity of methane are common and that most investigations have been conducted over restricted temperature and pressure ranges. This situation made it desirable to undertake an investigation with a scope common to most of the literature data available. APPARATUS AND MATERIALS The apparatus used in this investigation was the capillary tube viscometer&apos;described by Dolan,10 with modifications introduced in the general design and operation of the instrument. It has an effective pressure range from 14.7 to 10,000 psia and a temperature range from room temperature to 400F. The design of the viscometer is based on the establishment of a manometric head between two vessels containing the test fluid and a volume of mercury. The reservoirs are connected by a capillary tube through which the test fluid flows and a tube through which mercury flows. A pressure gradient is established by elevating one of the vessels above the other, the resulting flow of mercury displacing the test fluid through the capillary. The schematic diagram of the system (Fig. 1) shows the arrangement of the equipment auxiliary to the viscometer. The density cells assembly (E, Fig. 1) was not used in this investigation since reliable data are available on methane. 23 The assembly consists of a bank of eight 316 stainless steel pycnometers. Experimental values of the density of a natural gas19 and i-butane14 samples have been obtained for pressures up to 8,000 psia and temperatures up to 340F. The methane used was obtained from the Southern California Gas Co. Mass spectrometric analysis showed a composition of 99.8 percent CH4, 0.1 percent C2H6 and 0.1 percent C3H8. EXPERIMENTAL VALUES AND ACCURACY OF DATA Determinations were carried out at several temperatures. With the temperature in the cabinet controlled at a given level, a series of runs were made at various pressures. To establish pressures lower than that obtained from the methane cylinder, it was necessary to vent the gas slowly to the atmosphere until the desired pressure was reached. The consistency of the test run time for a particular condition can be used as a criterion for the accuracy of the data. A further check is obtained by comparison of the viscosity values obtained using different driving heads. To establish the instrument&apos;s reproducibility, a large number of runs were made at three completely different conditions of temperature and pressure. Data obtained were analyzed statistically to determine the most reliable value for the variance of the experimental data. It was found that the variances of the data taken at different experimental conditions were not statistically equivalent, but they were small. The largest variance was found at 8,000 psia and 100F, where the standard deviation was 0.385 micropoise. Therefore, 99.9 percent of the data can be expected to fall within 1.15 micropoises of the population mean, except for the intervention of systematic errors in operation.

By Oliver Bowles

WHEN a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibili-ties of much wider application. A wire saw consists of a 3/16-in. or 1/4-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1.) The teeth of the saw are sand grains carried in the grooves between the strands.

Jan 1, 1936

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By G. W. Jarman

THE purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electro- static separators and air flotation or air tables. MAGNETIC SEPERATORS In general, separating is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 980, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1938

By Breaux B. Castleman

The ultimate test of a business strategy is whether it achieves the owner&apos;s objectives. Most shareholders are interested in growth and profits, and share values on stock exchanges are very often closely correlated with profit growth and profitability measured as return on equity (ROE). Strategic management, then, involves managing investments or resource allocations to optimize long-term growth and real return on equity, within reasonable limits of risk. Figure 1 shows a plot of the five year, weighted average ROE of a number of communications companies against their stock market valuations in 1983, measured as a ratio of market value to book value. The principal explanation of the differences in the relative valuations of the individual stocks is historical ROE, weighted toward the most recent years. Further analysis demonstrates the added importance of growth in explaining the differences in stock market to book ratios. [ ] Research conducted by Booz Allen and others in recent years suggests that the relationships between ROE and market to book multiples hold true in industry after industry. Furthermore, we have found that in assessing business strategies for companies in these industries, the analyses should focus on whether proposed strategies are likely to lead to consistent long-term growth in real ROE, without excessive leverage. Our research also reveals, however, that these approaches to strategy assessment are not consistently applicable in the natural resource extractive industries. Figure 2 shows a similar comparison of market to book values against five year average ROE for a group of nine mining companies in 1983. Market value of the shares shows little correlation with ROE. [ ] Analysis of the data for other extractive industries indicates a similar pattern; that is, low correlation between share values and

Jan 1, 1985

By Evan Just

Government aid, regulation, and participation in the mineral industry are not new; they date back to the time when man first adopted communal living. Even in primitive tribal life, the obtaining of arrowhead or ceramic materials, washing of gold, or mining of copper were specialized activities, under tribal sponsorship. Later, when kingdoms, dynasties, and hierarchies developed, titles to mining properties were held by the sovereign or the state, work usually being done by slaves. Title acquisition through denouncement developed in Europe in the late Middle Ages and spread to the Western Hemisphere with the Spanish and Portuguese empires. Denouncements still recognized the rights of the sovereign in the requirement to pay royalties, which practice continues in many places today. Thus, anyone who views government participation in mineral activity as "encroachment" has no historical perspective. Only in a few countries and for a few generations have private interests enjoyed the right to exploit mineral deposits without the specific consent of the sovereign or without payment of royalty. Governments and the mineral industry have been linked together by other factors. Governments have had special interest in metals and minerals as stores of value and for armaments. Spanish conquests in the New World were energized by the lure of gold and silver. Pursuit of gold led to the American seizure of California in the days of the Forty-niners. The strategic importance of minerals in our own times has called for special steps to stimulate production in national emergencies and to prevent the enemy from acquiring mineral supplies. Our export controls to deny certain minerals to unfriendly countries, purchases for Government stockpile, and subsidies for domestic production are examples. Production regulation by state governments of oil and gas has become a well established routine. In brief, the mineral industry has never lacked aid, regulation, and participation by governments. The entrepreneur who wishes to explore for or develop minerals must deal with governments in most areas before he can begin, because mineral rights are reserved by them. He can proceed through discovery and de-

Jan 1, 1964