Search Documents

By Reamy Joyce

Conditions in underground mining are so variable that in approaching the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-urrs, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifications. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem. Variable Conditions A study was made recently of the untreated mine ties used by a bituminous coal company in two of its mines, which are about 20 miles apart. The mine ties were secured from the same sources for both mines. A careful check was made over a 10-yr. period on the life of untreated main-haulage ties, and it was found that in the mine where the haulage roads were on intake air the average life was approximately 5 yr., while in the other mine, where the haulage roads were on return air, the average life was 2 yr. A similar variability in untreated timber

Jan 1, 1940

By Reamy Joyce

Conditions in underground mining are so variable that in approaching the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-urrs, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifications. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem. Variable Conditions A study was made recently of the untreated mine ties used by a bituminous coal company in two of its mines, which are about 20 miles apart. The mine ties were secured from the same sources for both mines. A careful check was made over a 10-yr. period on the life of untreated main-haulage ties, and it was found that in the mine where the haulage roads were on intake air the average life was approximately 5 yr., while in the other mine, where the haulage roads were on return air, the average life was 2 yr. A similar variability in untreated timber

Jan 1, 1940

REPUBLIC STEEL CORP. and Armco Steel Corp. have joined in a $160,000,000 project for the production of iron ore from Taconite in the Lake Superior mining region. The two companies announced acquisition in equal shares of 100 pct ownership of the stock of Reserve Mining Co., which controls a vast deposit of magnetic Taconite iron ore on the eastern end of the Mesabi range in Minnesota. Through Reserve Mining the two companies will build a plant for manufacturing high grade ore from Taconite near Beaver Bay on the north shore of Lake Superior. The first announcement calls for about a $60,000,000 plant which will be built as soon as plans are completed and will have an annual capacity of about 2,500,000 tons of iron ore pellets. Longer range development plans call for future expansion of the plant to provide an annual capacity of 10,000,000 tons. This will amount to an additional investment of

Jan 10, 1950

By Keith Leonard Sutherland

This paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.14 Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. Purity of Reagents The xanthates were purified in the usual manner.' Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes, This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystalline powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. Results The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the "absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1943

By Keith Leonard Sutherland

This paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.14 Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. Purity of Reagents The xanthates were purified in the usual manner.' Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes, This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystalline powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. Results The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the "absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1943

By J. O. Mack, J. B. Russell

In recent years, solders containing 20 per cent tin with no bismuth or cadmium have been developed by a few companies, and personnel have been properly instructed in their use. In addition, since the tin shortage, a number of solders containing less than 10 per cent Sn, and some with no tin, are being used in special applications; however, a solder of this type has yet to be developed that is satisfactory for general use. Table i.—Composition Ranges Prescribed for a Commercial Substitute Solder Element Per Cent Tin............................ 18.0-20.0 Bismuth (maximum)a............ 0. 80 Silver.......................... O. 10-1. 25 Bismuth plus silver (minimum).... 0. 85 Antimony (maximum)............ o. 50 copper (maximum),,,,,,,,..,,,, 0. I3 Other elements, each (maximum)6 0.03 Lead........................... balance a When silver is present in excess of I per cent, the Bi content shall be 0.50 per cent or over. b Total not to exceed 0.10 per cent. The Purpose of this investigation was to develop an alloy containing a maximum of 15 per cent tin, with no cadmium or bismuth, having solder properties equivalent to or better than those of substitute solders now specified containing 18 to 20 per cent tin (Table I), or even approaching the properties of the standard 40 to 60 tin-lead solder. The wartime restriction of bismuth and cadmium, elements that have beneficial effects on fluidity, solidification range and strength, makes it increasingly difficult to develop a general-purpose solder containing a maximum of 15 per cent tin. In the course of this investigation, 11 elements were used in various combinations with the basic I5-85 tin-lead alloy. These elements were antimony, silver, copper, indium, thallium, lithium, calcium, barium, potassium, sodium and arsenic. In all, 116 low-tin solders were investigated, with the idea of developing a solder that will give satisfactory working properties, specifically in regard to "wetting" of copper, brass and iron, solidification range, capillarity and shear strength of a soldered joint. The relative importance of these various properties plays an important role in the search for substitute solders, since it is almost impossible to retain all of the desired qualities of a high-tin solder and still make drastic changes in the alloy composition. Because of the expected uses of a general-purpose solder, it is necessary that it have properties, especially in regard to wet-tability, that will enable it to be used on the metals in common use. Basic Considerations The maximum liquidus temperature of a solder is determined by the particular application involved and the temperature that can be obtained by the source of heat. If a soldering iron is used, it must not only

Jan 1, 1945

By Douglas A. Karvonen

INTRODUCTION Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960's - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan, is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth, with about 5% of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40% of known world potash reserves and its ten active mines account for some 25% of annual world production. POTASH CORPORATION OF SASKATCHEWAN In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan, the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation's Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product, and conducting all of the other activities necessary for a successful corporation competing in the world potash industry. The corporation is the largest potash producing and selling organization in the Western World - or third largest in the world. (See also Figure 1). PCS through its wholly-owned subsidiary, PCS Mining, has acquired a whole or partial interest in five geographically distinct producing properties or divisions, representing today more than 40% of Saskatchewan's potash producing capacity. The acquisition of each division was followed by a program designed to exploit and maximize the particular opportunities at each minesite for increased production. To that end, PCS Mining has taken an active lead in expanding to meet future demand and has implemented expansion programs at all properties except for its Esterhazy Division where it has a long-term processing agreement with International Minerals & Chemical Corporation (Canada) Limited. Through its wholly-owned subsidiaries, PCS Mining, PCS Sales and PCS Transport, this provincial crown corporation has the ability to operate as a producer and marketer of Saskatchewan's potash. In certain instances PCS, the parent company, assists in the financing of various projects undertaken by the subsidiaries and in other cases the subsidiary involved arranges its own financing. POTASH RESERVES As a background to the specific issue of financing, it is helpful to describe briefly the nature of the deposit which supports the industry - our collateral, if you like. The potash beds underlying Saskatchewan are sedimentary rock deposits formed by the gradual evaporation of an inland sea during the Middle Devonian period roughly 400 million years ago. Now known as the Prairie Evaporite, this formation stretches from North Dakota and Northeast Montana through Southern Saskatchewan into North-Central Alberta. These beds lie at mining depths ranging from 950 - 1000m (3,000 ft) below the surface, where conventional mining methods can be used, and to 1,650m (5,000 ft), where solution mining must be

Jan 1, 1985

By Frederick Rhines

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ? in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activa-tion heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. Much of the argument concerning the properties of metals that deter-mine D and Q has been drawn from data in which variations of the quan-tities with concentration are unknown, for these data- have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concen-trations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By M. G. Benz, J. F. Elliott

A new type of solution calorimeter has been constructed to measure heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction at temperatures above 1000°C. With it, measurements hove been made of the partial molar heats of mixing joy tin in the Cu-Sn system from 0 to 13 at. pet Sn at 1127°C and fir nickel in the Cu-Ni system from 0 to 9 at, pet Ni at 1200°C. The integral molar heat of mixing for the Cu-Sn system is strongly negative with a calculated minimum value corresponding to the composition Cu3Sn. The integrnl molar heat of mixing for the Czi-Ni system is slightly positive at these temperatures. These integral molar values have been measured with a probable error less than 30 cal per g-atom at an atom fraction of nickel or tin equal to 0.1. The estimated probable error for the Cu-Sn system is approximately 450 cal for a measured heat of solution of approximately 9000 cal. For the Cu-Ni system it is approximately 700 cal for a measured heat of' solution of approximately 60 cal. A new type of heat of solution calorimeter was designed and constructed to provide a more accurate experimental method for determining heat effects at high temperatures, (T > 1000°C). With it, partial molar heats of mixing, enthalpy increments, heats of fusion, and heats of formation and reaction for metal systems can be measured directly. Previously it has been necessary to rely upon the use of the dropping calorimeter or the van't Hoff equation applied to equilibrium data for this information. For the most part equilibrium data are scarce and difficult to obtain in many cases, and it has been necessary to rely upon the "method of mixtures" for the desired enthalpy measurements. An earlier study1 provides a prototype for this work. The "method of mixtures" as outlined by K. K. kelley,2 "consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a calorimeter operating at or near room temperature.'' In this manner the change in the total heat content (enthalpy) of the substance between the temperature of the furnace and that of the calorimeter is determined. In order to determine high-temperature heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction, it is necessary to take the difference between two such measurements, one before and one after the occurrence of the enthalpy change being studied. The desired enthalpy change is then the small difference between two large numbers. Small errors in the large numbers are included as large errors in this small difference. It is this difficulty that must be avoided for accurate measurement of the desired functions. The procedure with the new solution calorimeter consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a solution calorimeter operating in the temperature range of 1000o to 1200°C. Measurements in the range of 1200" to 1600°C are planned for the future. By selection of the composition and

Jan 1, 1964

By H. S. Geismer

INTRODUCTION. THERE are three general methods available for obtaining commercial brown iron-ore : hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all foreign material to be separated from ores before they are delivered to the furnace, and hand-screened ores can rarely be made to fulfill that requirement. Another argument against hand-screening is, that the waste-pile often contains as much ore as the screen recovers. The operation known as hand-screening consists of throwing the ore-bearing material against a stationary inclined screen of 0.5- to 0.75-in. mesh, similar in construction to the screens employed in sand-pits. The recently-prospected brown-ore deposits of Cuba seem to offer possibilities for hand-screening not possessed by the average American deposit, since these ores are not associated with worthless clays. Washing, and washing and concentrating, may be discussed together, since concentrating is never practical on brown iron-ore, except to treat ores that have already been washed. (Strictly speaking, washing might be classed as concentrating, but it is never so designated by brown-ore men.) The various steps of removing ore-bearing material and converting it into ore suitable for blast-furnace use, may be grouped under five heads: loading for transportation ; transporting ; feeding into the washer; washing; and concentrating. These five subjects will be considered in consecutive order. Each of these successive steps may be accomplished in a number of different ways, the choice depending entirely upon the character of the ore-bearing material to be treated.

Aug 1, 1911

By A. L. Ph. B. Holley

(Read at the Philadelphia Meeting, February, 1878.) THIS paper is an abstract and a discussion of results obtained by the United States Test Board in experiments upon 14 brands of wrought iron, most of which are well known and of high repute.* The iron was all intended for chain-cables; it was tested in the form of bars, usually of nine sizes, from 1 inch to 2 inches round, and also in the forms of single links and short chains. Not less-than 2000 tensile tests were made, each showing elastic limit, elongation, and reduction of area. This work was done with conspicuous intelligence and fidelity, at the Washington Navy Yard, by Commander L. A. Beardslee. Some important practical results and principles which he has developed, and others which he has confirmed, will be referred to. The chemical part of this work consists of 42 complete analyses (including slag), by Mr. Blair, chemist to the Board. EFFECTS OF COMPOSITION ON STRENGTH. Variations in the physical qualities of iron may he due to different composition, or to different treatment in manufacture, or to both these complex causes. In order to determine the specific causes of variation, one class of altering conditions should be made to vary largely, while the other classes should be kept uniform. Then another class should be varied, and so on, until the value of each is ascertained. As all the irons under consideration were intended to have that purity and refinement which was deemed indispensable in chain-cables, their chemical analyses are perhaps more important in proving that physical variations result chiefly from treatment, than in pointing out the specific effects of certain ingredients. While the subject of treatment-especially the increase of strength by greater reduction in rolling-may be the more important one, it can be best appreciated after we have familiarized ourselves with the gen¬eral chemical and physical characters of the irons. The typical facts are given in the following tables. * As the present object of the Board is not to compare the products of different makers, but to discover the physical effects of various composition and treatment, the irons are designated by letters rather than by their trade names.

Jan 1, 1878

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1951

By Gordon G. Bentle, W. P. Fishel

GREINER, Marsh, and Stoughton1 have reviewed the literature in a monograph on the iron-silicon system. The lack of agreement among the various studies may be due to the difference in the purity of materials in some cases. The results of the X-ray method indicate only a general rather than a specific limit of the y loop. The iron-titanium system was investigated by Roe and Fishel,' whose results are used in determining the iron-silicon-titanium y loop. The literature indicates that no study has been made thus far of the iron-silicon-titanium system in the y loop region. Experimental Procedure The alloys were made from Armco iron, 99.86 pct Si, and 98.5 pct Ti. The titanium contains 1.07 pct Fe. The Armco iron contains 0.01 pct C, 0.005 pct Si, 0.02 pct Mn, 0.006 pct P, 0.01 pct S, and 0.04 pct Cu. A dilatation sample of Armco iron was prepared in the same manner as were the other samples. Several dilatation runs indicated that Ac3 begins at 905°C and ends at 910°C, which compares favorably with the study of Wells, Ackley, and Mehl' employing specially purified iron. All alloys were melted in an induction furnace in Alundum crucibles and were top poured into baked core sand molds. The ingots weighed about 600 g as cast. Dilatation samples of 4 in. by % in. diam were taken from the bottom end of the ingot, from which turnings for analysis were taken. Turnings from each end of two of the samples indicated that the alloys possessed uniform silicon content. A hole was drilled halfway through each end of a 4 in, dilatation sample. A chromel-alumel thermocouple was inserted in each hole and the surrounding metal peened in to hold the thermocouple in place. Fig. 1 represents the dilatation apparatus. The heating unit is an Alundum tube wound with resistance wire; the dilatation tube is a McDanel combustion tube; the push rod is zircon; the dial gage is graduated in 0.0001 in. and was vibrated to prevent sticking. A blank run over the temperature range of interest gave no significant dilatation. The thermocouples were attached to a multiple recording micromax which indicated the temperature at each end of the sample at 35 sec intervals. A Lindberg control unit governed the rate of heating of the furnace, and lowering or raising the

Jan 1, 1957

By W. D. Brown

Newell1 has shown that hydrogen is removed from steel in a vacuum at a temperature of 500° to 900° C. within 136 hr. Holm and Thompson2 also state that, especially when the hydrogen is high, the results obtained by extraction at 800°C. agree with those obtained by vacuum fusion. In this laboratory, an apparatus was designed (Oct. 1940) and used wherein the piece of steel was heated at 100°F. in a Torricellian vacuum (Fig. I). This vacuum was produced by raising and lowering a "leveling bottle or bulb" containing mercury. Extensive tests were made with this apparatus. The weakness of the procedure was the possibility of leakage of air into the tube around the rubber stopper at the bottom. The present plan is to raise and lower the mercury by applying vacuum from a mechanical pump, to the top of the tube and then to a bottle of mercury in which the bottom of the tube is immersed. The Apparatus The extraction is made in a Pyrex tube A, I in. i.d. It is drawn down at the top at N and an 8-mm. i.d. tube is welded on it. To this a Pyrex stopcock E, 4-mm. bore, is welded. The tube between N and E is preferably 8 in. long and is graduated in milliliters. The total length of A to the stopcock is 28 inches. Heat is supplied by a split-tube furnace. 0 in. long by 6 in. in diameter, hinged on the side. A short pyrometer couple P is inserted through the walls of the furnace. In use this is standardized by comparison with a standard couple in a I-in. tube, just opposite this short couple. In the I-in. tube A a glass rod R, flattened at one end, supports the sample S and the length of R is so adjusted that the sample is in proper place. (It may float in the mercury.) The tube A is inserted in a large rubber stopper to fit the bottle B and extends nearly to the bottom. It is so placed that the handle of the stopcock faces the operator. In this stopper also is a short tube D bent at right angles for the application of vacuum. Also in this stopper is an 8-mm. tube C reaching nearly to the bottom; this is bent so as to miss the heater and again bent to bring it in line with and as near as possible to the upper and reduced part of tube A. On this tube C is welded a 4-mm.-bore stopcock H. In order that the two tubes may be as near as possible, the handle of stopcock H faces the back, or is the reverse of stopcock E. The total height of II above the bottom is 28 in. As explained later, this is the pressure-measuring tube C. The bottle B is about half full of mercury. The mercury must cover the ends of A and C by about I in. when they are evacuated. By tees T and rubber tubing RT the tubes A, C and D, the latter through the three-way stopcock M, are connected to the vacuum pump. A sheet of asbestos at K prevents the stopcocks E and H from becoming so hot that they leak. A good grade of vacuum lubricant prevents leakage of E and H. In order to measure the pressure of the

Jan 1, 1945

By John V. Beall

Dear J. B.: The recent cable I sent you for a transfer of $200,000 was the outcome of the diligence and perspicacity of our group which, as you know, is laboring under severe hardships here in Rondônia. I only mention the latter difficulties in passing because no reply has been received to our urgent appeal for money. As much as I detest appearing to plead for more attention than you feel called upon to pay to our forgotten mission, I can assure you that it would be in the best interest of the company for you to do so. The fact is, we have been able to outmaneuver the competition and have succeeded in securing pesquizas on some of the most promising cassiterite gravels. We have not been able, up to now, to do much bulk sampling (for lack of funds) but our preliminary panning shows great promise as you can see from the enclosed assay sheets.

Jan 1, 1971

By Paul A. Farrar, Sanford Adler

The Tz-Zr system was reinvestigated using both metallographic and X-ray diffraction techniques. It mas found that titanium and zirconium are soluble in all proportions in both the a and 0 phases. The minimum in the transformation was found at 50 at. pct and 535°C. THE Ti-Zr system has previously been the subject of several investigations.1-6 A study by Hayes et al.5 using magnesium-reduced titanium and zirconium melted in graphite crucibles indicated that the system was a continuous series of solid solutions in both a and 0 phases with a minimum at approximately 545°C and 65 pct* Zr. These conclusions were substantiated by the work of Duwez4 as well as by the limited data of Craighead et al.,3 Fast,2 and deBoer.1 However, a more recent investigation of the titanium-rich region by Ence and Margolin6 indicated that the solubility of zirconium in a, titanium at 500°C is approximately 22 pct with the a + 0 field extending to approximately 47 pct Zr. Therefore in order to resolve this discrepancy the following investigation was initiated. EXPERIMENTAL PROCEDURES The alloys used in this investigation were prepared as 20- to 30-g buttons by nonconsumable electrode melting in a helium atmosphere. The starting materials were Bureau of Mines titanium BHN 71 and Foot Mineral iodide crystal bar zirconium. The titanium was premelted before the alloys were prepared to avoid excessive weight losses in the final melting. The compositions of the alloys prepared were as follows: Ti-12.0, 22.2, 29.0, 39.6, 50.0, 58.0, 72.4, 83.5. and 90.8 pct Zr. Prior to heat treatment the alloys were cold-worked 10 to 20 pct, stopping at the first signs of cracking. Specimens for heat treatment were wrapped in molybdenum sheet and annealed in argon-filled quartz capsules for the following times and temperatures: 750°C-40 days, 675°C-61 days, 600°C—109 days, 575°C-112 days, 550°C-112 days, 525°C—127 days, and 450°C —153 days. Quenching was accomplished by breaking the capsules in an iced-brine solution. The standard techniques used for polishing the specimens involved belt grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch7 or "R" etch 8 Debye-Scherrer X-ray powder photograms were obtained for a number of samples using a 114.6-mm camera and CuK, radiation. Exposure times were from 19 to 23 hr. The powder samples were obtained by filing to 270 mesh size. After filing the samples were wrapped in molybdenum foil capsuled in quartz and reannealed at the temperature of original heat treatments; following the heat treatment the samples were quenched into iced brine without breaking the capsules. RESULTS AND CONCLUSIONS On the basis of the microstructural examinations of the heat-treated samples and of the X-ray diffraction data, the Ti-Zr system shown in Fig. 1 was constructed. The data indicate that a, and 0 titanium form a complete series of solid solutions with a, and ß zirconium. The minimum was found to occur at 65 pct (50 at. pct) Zr and 535°C, in excellent agreement with the earlier investigations,1-5 see Fig. 2. Typical microstructures are shown in Figs. 3 to 7. Figs. 3, 4, and 5 show the 22.2, 39.6, and 50.0 pct Zr alloys after heat treatment at 675°C for 61 days with the 22.2 pct Zr showing equiaxed a, and the 39.6 pct Zr alloy a + transformed ß, while the 50 pct Zr alloy shows only transformed B. Figs. 6 and 7 show the 29.0 and 39.6 pct Zr alloys after heat treatment for 109 days at 600°C. The 29 pct Zr alloy has an equiaxed a structure while the 39.6 pct alloy has a partially recrystallized a+ß structure. X-ray diffraction data obtained from the 50 pct Zr alloys after heat treatment at 525° and 450°C as well as from the as-cold-rolled material showed only those lineos which couid be indexed a: a titanium, good agreement with the previously published values. 2,4,5,9 Chemical analysis* of the 50 pct Zr alloy

Jan 1, 1967

By Edward L. Fidler, Thomas E. Finch

Thin seam coal mining in the western US nominally equates to recovery of stray seams associated with thicker, major seams. The thin or stray seams encountered are generally recovered, but not in all cases. The alternative to extraction is, of course, spoiling. The majority of thin seams are encountered somewhere in the overburden above the major seam or in the parting between thick seams. Although some are true strays and appear anywhere in the geologic sequence, others might be classified as thin "rider" seams immediately above or below a thick seam and separated by some equally thin parting. For the purpose of this discussion, stray or thin seams are defined as those which are less than 1.2 m thick or represent less than 10% of the expected extractable coal. [Figure 1] is a graphic representation of typical thin, stray, or rider seams which actually appear in a western operation. Operationally, stray seams create irritating scheduling problems and require special handling techniques which do not always lead to efficient equipment utilization. Additionally, coal recovery from a thin seam is considerably less than the 95% usually recovered from thick seams. Higher recovery in thin seams leads to dilution problems, which depreciates Btu quality, and most western coals are not in a position to lose heating value. Thin western seams also undulate and pinch or swell more than thick seams, and this leads to more difficult recovery. Often they are associated with equally dark carbonaceous shales and visual selectivity is difficult at best during daylight hours. Resource Recovery Regulations Thin seam recovery in western mines is encouraged by both federal and state regulations and by the mining industry's concern for total resource recovery. [Table 1] lists the western coal states and their recovery regulations. The federal regulations are found in the Surface Mining Control and Reclamation Act of 1977. They state, "General performance standards shall . . . require the operation as a minimum to … conduct the surface coal mining operations so as to maximize the utilization and conservation of the solid fuel resource being recovered." Economic stimulation for thin seam recovery appears to be marginal or at the least controversial. Scheduling and operational problems often outweigh the nebulous profits created by engineering analysis. The only alternative to extracting thin seams occurring above major production seams is to strip directly through them and lose the resource to the spoil pile. Although this is not palatable to environmental emotions or resource promoters, it is the most simple expedient to operations people.

Jan 1, 1981

By W. J. Slatosky

W. 0. Philbrook (Cairiegie Institute of Technologyogv—Mr. Slatosky has presented an interesting and constructive paper that represents another step along the way of converting steelmaking from an art to a science. I am confident that his computer will be practical and successful and that with a very few months of experience it will provide a significantly better degree of control than his record of 65 pct of heats within range obtained with the slide-rule calculator . A paper such as this, with a lot of symbols and condensed mathematics, is difficult to comprehend quickly. Since I have had an opportunity to study it carefully, perhaps my evaluation of its validity and accomplishments will save time for others. Mr. Slatosky has correctly used standard principles of stoichiometry and heat balances, which are available to anybody, but he has also brought to them two original contributions: 1) He has developed from operating data some empirical relations for predicting the final FeO content of the slag (at 0.5 pct C end-point) as a function of slag basicity, lance height, and scrap, ore, and scale in the charge. This improves the accuracy of prediction of temperature or scrap requirement compared with assuming an arbitrary, constant FeO content at the end of each heat. There is no assurance yet that exactly the same relations will hold for other furnaces or practices, but similar correlations can be expected. 2) He has combined calculations that are ordinarily carried out laboriously as a number of individual steps into a single, simple linear equation that can readily be fed into a machine. This involved a tremendous amount of painstaking detail work as well as the imagination to see the possibility and work out the steps. While his particular Eqs. [3] and [6] are valid only for the furnace design, charge weight, and blowing time used at Aliquippa Works, only a few numerical values have to be changed to adapt it for other conditions. In order to arrive at a useable solution, Mr. Slatosky had to make some basic assumptions about the process that are similar to those used by others. He neglected variation in some process variables and assumed an arbitrary average value for waste gas analysis and temperature for want of more exact information at the present time. All of these judgments are clearly stated. In addition, some thermody-namic data presently available are not adequate for the job, notably in relation to heats of formation and sensible heat in slag, and some expedient has to be adopted to get around the difficulty. Other people might prefer slightly different judgments about these details and hence obtain somewhat different numerical solutions. This is not of serious importance, however, because the errors accumulate in the "heat loss" term and are largely self-compensating for a constant heat time. Although the extended Eq. l(a) in Appendix I was set up as a rate equation originally, for convenience in using an analogue computer as stated in the paper, the time dependence was removed by later mathematical manipulations and assumptions about the process. The final result is an integration of element and energy balances from initial to final states; this procedure is as legitimate here as in any other form of heat-balance calculation. The formal handling of stoichiometry and thermochemistry appears to be correct, and it is assumed that any arithmetical errors would have come to light in applying the calculations to furnace practice. Mr. Slatosky's approach is not necessarily unique, in that other people might start with apparently different equations or prefer another form of final equation for another type of computer. However, he has presented an accomplished result that appears to be a theoretically sound and practically useful way of applying scientific principles and rapid computation for better control of steelmaking. His success will undoubtedly encourage himself and others to improve on the mathematical model and its use as better informatioq becomes available. John F. Elliott (Massachusetts Institute of Teck-t2ology)-The last comment by Mr. Richards that a calculator is quite unnecessary for an L-D operation ?-equi??es a rebuttal. The L-D furnace is a very high capacity process which places a premium on close control. When one is making steel at rates between 100 and 200 tons per hr, one cannot afford the luxury of an extra 5 or 10 min at the end of a heat correcting for an error that should never have been made in the first place. Mr. Slatosky's paper is a very sound application of the simple principles of stoichiometry and the energy balance. It is a satisfactory and valuable start, but only the start of the development of methods of control for this process. An analysis of the process shows that it should be very suitable to control by a computer. This is especially the case when various grades of steel are to be made. In fact, it would seem that the organizations who are planning new and bigger installations of L-D vessels should consider carefully the advantages that would stem from computer control of a vessel with the operator present to do little more

Jan 1, 1962

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957