Search Documents

By B. M. Larsen, W. E. Shenk

This paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable —that is, the time interval between successive reversals—should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one lLminimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: I. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potenti-ometric control instrument, to correct any tendency toward temperature unbalance between ends of the furnace. 3. A second "maximum temperature

Jan 1, 1945

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By R. W. Jigins

OPERATIONS of the Braden Copper Co. are in the Chilean Andes, southeast of Santiago. Most remote of the company communities is Sewell, a town of 12,000 people, 7000 ft above sea level at the junction of the Coya and Teniente rivers. Four miles down the Coya River is the smelter town of Caletones, elevation 4500 ft, with a population of about 3000. At the junction of the Coya and Cachapoal rivers 24 miles below Sewell is Coya, eleva- tion 2500 ft, location of the company's two hydro- electric plants. The principal accounting offices; steel, iron, and brass foundries; railroad shops; and major mechanical repair and fabricating shops are at Rancagua in the central Chilean valley, 44 miles from Sewell. The company owned narrow-gage railroad connects with the Chilean national railroad at Rancagua and above Coya is the only modern means of travel. El Teniente mine at Sewell is the largest under- ground copper mine in the world. The mill, at the portal of the main tunnel, has a capacity of 34,000 tons of crude ore daily, although production is lower during the winter beacause of electric power restrictions. When operating at capacity the mill produces 2000 tpd of copper concentrates and 32,000 tpd of tailings. Tonnage of tailings is equivalent to about 100,000 tons of pulp at normal water to solid ratio.

Jan 10, 1957

T. M. Drown, South Bethlehem, Pa.: Mr. Thackray's paper shows in a striking way the high degree of rapidity and ac curacy exhibited by the chemists of our steel-works in ordinary everyday practice. That determinations made in an hour should present only slight differences in the third place of deci male is certainly matter for surprise and congratulation. This remarkable result has been due, perhaps, in part, to a remark able cause. The managers of works, ignorant of all the diffi culties of the laboratory, have demanded "the impossible " of their chemists—and the chemists have done it! Andrew A. Blair, Philadelphia, Pa.: Mr. Thackray's paper is extremely interesting, especially in its bearing on the question of a standard method for the rapid determination of phosphorus in the laboratories of steel-works. Before discussing the re sults in general, I desire to explain the results obtained by me under method A'. This is the method which I have used in the work of the sub-committee on Methods of the Interna tional Steel Standards Committee. It may be described briefly as follows: Solution in nitric acid; oxidation of carbonaceous matter by permanganate; precipitation of phosphoric acid by molybdate solution; reduction of molybdic acid in the reductor, and titra tion by permanganate. This method was used apparently by only three chemists, Dr. Dudley, Mr. Crowell, and myself. In determining phosphorus by this method, among the most essential points to be considered are the ratio of iron to molyb dic acid, or the reducing action of zinc on molybdic acid as compared to its reducing action on iron, and the ratio of molyb dic acid to phosphorus in the ammonium phospho-molybdate obtained by precipitation from the solution of the steel. In regard to the first point, the usually accepted ratio is 1 to 0.90756, or, as it is roughly stated, 0.9076, which is based on the assumed reduction of the molybdic acid to Mo12019,. This

Jan 1, 1896

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936

Jan 1, 1884

By J. W. JESSUH

TO certain people the name of Northern Rhodesia brings only a vague recollection of a distant country somewhere in Africa; to others, it means a big game territory and the opportunity for excellent shooting; to some, a land of sunshine and peace; but to mining men the name signifies the land where the latest discoveries of copper ore are astonishing the mining world and bid fair, in a few years, to make Northern Rhodesia one of the largest copper- producing countries. There is a fascination about this part of the globe that is somewhat similar to southern California, and at the same time there is that feeling of mystery peculiar to a tropical climate. Perhaps it is the isolation, the fear of wild animals, or the influence of an undefinable something which cannot be expressed.

Jan 1, 1931

By John V. Beall

As Mother Nature arranged it, the hottest potential mineral target in the country today, the Stillwater complex had to occur in a spectacular natural setting-the north margin of the Bear Tooth Mountains of Montana. What more appropriate backdrop for the August 17-18 field hearings of Senator Frank E. Moss (D-Utah). His subcommittee, on Minerals. Materials and Fuels, heard 37 witnesses ponder the value of minerals vs esthetics or other uses of federal lands. On August 17, four Army Hueys swept the senatorial party, the press, Forest Service Officers and such distinguished witnesses as Montana Governor Forrest H. Anderson over the Custer-Gallatin National Forests, besting the thin air of 10,000 ft p1us, they set down on Iron Plateau.

Jan 1, 1971

By G. W. Jarman

The purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electrostatic separators and air flotation or air tables. Magnetic Sepaeatohs In general, separation is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 080, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1942

By G. W. Jarman

The purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electrostatic separators and air flotation or air tables. Magnetic Sepaeatohs In general, separation is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 080, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1942

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole. The Calcite plant operates a limestone quarry near Rogers City, Mich., in the northern part of the lower Michigan peninsula. The formation quarried, a portion of the middle Devonian series, is the Dundee limestone, which is uniform, seldom massive, and characterized by definite bedding planes. The dip is southeast, 40 ft to the mile. Quarry faces vary from 20 to 116 ft in height. Vertical blastholes are used entirely, from three to five rows of holes being drilled parallel to the working face, spaced 18 ft apart with 18-ft burden and drilled 6 to 8 ft below shovel grade. Quarry operations coincide with the navigation season on the Great Lakes, as the bulk of the stone is transported by lake carrier. The normal operating season runs from April to December, the remaining time being devoted to stripping operations and plant and equipment maintenance. In the followirig discussion drilling rates mentioned refer to overall drilling time and include all operations such as moving from hole to hole, penetration and extraction of tools, and routine maintenance. Time consumed by such factors as power delays and major machine repair is not included in drilling time unless otherwise stated. Figures cover only operations at this one plant in the formation mentioned. Needless to say, a very different set of figures could be obtained in a different formation. However, the comparison of footage obtained with churn drills and rotary rigs in this particular formation has been used as an indication of what might be the expected performance of rotary rigs in other formations. Prior to 1950 the bulk of the blasthole drilling at the Calcite plant was done by electrically powered churn drills. Both crawler and wheel-mounted rigs were used. These machines, which mounted a 22-ft drill stem of 4½ in. diam and a spudding type of bit 2 to 4 ft long, drilled a hole of 5 ?-in. diam. Average drilling rate of these rigs in the Rogers City formation was 8 % ft per hr. In 1946 one of the first rotary blasthole drills offered to the quarry industry was put into use on an experimental basis. This machine, known as the Sullivan Model 56 blasthole drill, Fig. 1, was on 16-in. crawler pads and electrically powered at 440 v. The drill bit, a Hughes Tri-Cone roller bit of 5?-in. diam, Type OSC, was threaded into the end of the 4-in. square hollow drill rod or stem. These drill rods were 20 ft long with female threads on one end and male on the other to allow for addition of the desired number of rods for drilling holes of various depth. Rods were handled by a single drum hoist geared to the main drive motor and racked by a 30-ft derrick or mast when not in use. The cable from the hoist drum fed through a crown block on the top of the derrick back to the water swivel mounted in the top end of the drill stem in use. This cable remained attached during drilling operations and was used to hoist the tool string from the hole. Down pressure was applied to the tool string by means of a pair of 4-in. diam hydraulic cylinders acting on the drill chuck holding the drill rod. The first chuck consisted of flat jaws which gripped the flat sides of the stem. These jaws were controlled by set screws forcing them into contact with the drill stem. As these set screws had to be loosened and tightened by hand with each stroke of the hydraulic feed cylinders, there was great delay. For this reason the semi-automatic chuck was developed which automatically gripped the stem on the downward stroke but released for retraction of the hydraulic feed cylinders. Rotation was imparted to the tool string by a rotary table acting on the chuck and geared to the main drive motor through a separate gear train and clutch. A positive displacement water pump, mounted on the drill, fed water through a system of pipes and hose into the water swivel mounted on the top of the drill rod and through the rod and bit, washing the drill cuttings to the collar of the hole. Where water was scarce, provision was made to settle out the cuttings coming from the collar of the hole and re-use the water. Where water was abundant the stream coming from the hole was wasted. Drilling rate with this machine was about 20 ft per hr and bit life 1600 ft of hole. While this rate was more than twice that obtained with the churn drills employed, the problem of water supply and drill cuttings disposal rendered the machine impractical from an operating standpoint. Consequently it was used only in that part of the operation for which water was easily supplied, when the character of the formation made it least difficult to wash cuttings away from the collar of the hole. In October 1949 it was suggested that drill cuttings be removed by compressed air, long used for this purpose on pneumatic drills, and collected at the collar by suction. Thereafter, the water pump on the Sullivan 56 was replaced by a 500-cfm air compressor and a trial run made. Air pressure at

Jan 1, 1955

• In 1949 the United States imported 7,400,000 tons of iron ore; Chile, Sweden and Canada, in that order of importance, supplied over 80 pct of this amount. U. S. imports have increased from 3 pct of the total supply in 1940 to 8 pct in 1949. • Mica has been successfully synthesized by scientists of the National Bureau of Standards. quartz, magnesite and bauxite, plus a fluorosilicate compound to act as a crystallizing agent, are heated to 2500°F in a platinum-lined crucible and as the furnace cools mica crystals grow. The key to parallel growth to make sheets is in precision control of temperature. • Inland Steel Co. of Chicago has taken an option to lease from Steep Rock Iron Mines, Ltd., of Canada -- a large undeveloped acreage in the vicinity of Steed Rock Lake, Ontario -- for the purpose of exploring and developing a new iron ore mine. The exploration program is expected to begin at an early date. •A 20-yr test conducted by the U. S. Bureau of Mines with the cooperation of Cleveland-Cliffs indicated that chemically treated timbers last from 2 to 3-1/2 times as long as untreated ones set in the same passageway. Of the three reagents used, zinc chloride gave the best result -- 13.3 yr as compared to 3.8 yr for untreated timber. •Senator Pat McCarran charged that President Truman used a "shotgun approach" to the taxation problem when he accused the mining industry of enjoying excessive depletion exemptions when actually mining taxes should be lowered. He introduced to the Senate a report of the National Advisory Council -recommending a decrease * The country's first graduate program of research and instruction in conservation of natural resources will begin at Yale in September. The Conservation Foundation is supplying $20,000 a year to finance the program. •Felix E. Wormser urged that adequate tariff protection should be provided to offset effects of devaluation on the domestic mining industry in an address before the Colorado Mining Association. He advocates tariffs rather than subsidy legislation, such as S. 2105, for the protection of the lead-zinc miners because the latter would promote inefficiency and "impair our priceless free market." •"It may be startling to realize that for the world's white population the per capita requirements for minerals have multiplied 30 times in 30 yr, or that more minerals have been mined in the last 40 yr than in all prior history." -- Evan Just, in "Mineral Depletion and Metal Supply." •The National City Bank in its monthly letter states that both management and the unions concede that there are too many miners trying to make a living out of the industry for its present market. •On Feb. 3 it was reported that 6000 Anaconda employes in Chile quit jobs in sympathy with striking telephone and electric workers. The government has ordered them back to work on penalty of discharge. It appears that the walkout will not be prolonged in view of the government stand.

Jan 3, 1950

By Samuel E. Doak

The utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose, loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 11/2 per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In modern practice the percentage of sulphur in the cinder is rarely as great as six, and seldom lower than one and one-half. Average analyses for iron, silica, and sulphur of the cinders that have come under my personal observation are as follows:

Jan 1, 1916

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By Yeatman, Pope

FOR many years geologists have felt that mining companies should adopt a more liberal policy in the publication of their reports. The increasing usefulness of the geologist to the mining profession in recent years demands that consideration be given to this question. Prior to 1900, the call for geologists of high reputation by mining companies was probably mainly in connection with lawsuits arising from the interpretation of rights or ownership as defined by the "Law of the Apex," and from problems such as finding the continuation of the vein or whether the vein followed was the main one or a branch. Later, outside of legal questions, the most intensive and general use of their services arose from the search for oil. Geologists to determine the position of the formations

Jan 1, 1938

In uranium metallurgy, the main purpose is to obtain a product containing 80-85% U308 (yellowcake) from ores whose average grade is a mere 0.21% U30& Essentially, the task of extraction and concentration involves dissolving the ore's U308 values, followed by purification and concentration of the uranium-rich solution (using such operations as filtration, clarification, and ion-exchange), and then selectively precipitating and isolating U308. Leaching is First Step In yellowcake production mills, the first chemical change occurs by leaching the ore with either sulfuric acid-as done by Anaconda and Kerr-McGee-or with an alkaline solution of, say, sodium carbonate, as done by United Nuclear-Homestake Partners. The choice of either acid or alkaline leaching is not an arbitrary one: it depends on the chemical and physical characteristics of a particular ore. That is, on the presence of clays, organic compounds (usually of carbonaceous origin), and soluble impurities, as well as on the ore's wetness and grindability.

Jan 8, 1974

By Charles Will Wright

FRANCE will be given a large portion of the Marshall Plan funds for relief, reconstruction, and industrial development in France and in her colonial possessions. At present that country is not in position to export any large tonnages of the mineral products needed in the United States. However, if, through Marshall Plan aid and private capital investment, production of these products can be largely increased, agreement should be made by which the United States is to get a substantial portion of such increased output in part payment for the material and technical aid they receive. France issued a decree, published in the "Official Gazette" on Feb. 3, 1948, which permits conversion into dollars of dividends derived from dollar investment in Government-approved projects and will agree to a scale of capital amortization to be determined in each individual case. This decree is to encourage private capital to cooperate with local capital in industrial undertakings. The French Colonial Ministry has prepared an extensive program for aid to the mining industries in overseas possessions to be undertaken by

Jan 1, 1948

By John T. Norton, R. E. Hiller

The tremendous increase in the use of metals that have been prcpared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations. It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metjal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing. Preparation of Samples The tubing samples used in this investigation were made of steel having a carbon content of 0.10 to 0.20 per cent, and were drawn on a standard type of draw bench. In order to obtain the large reductions, the annealed stock was coated with lead, for purposes of lubrication. The reductions of area stated refer to reduction from the annealed condition without intermediate heat treatment. The cold work was done as nearly as possible at room temperature. The samples of wire and strip used for purposes of comparison were of steel of approximately the same carbon content and were prepared in the manner indicated. X-ray Method of Investigation The condition of preferred orientation in cold-worked samples is best investigated by the X-ray method that employs a small circular beam of * Assoriate Professor of Physics of Metals, Massachusetts Institute of Technology. t Graduate Student, Department of Metallurgy, Massarhusetts Institute of Technology.

Jan 1, 1932