Search Documents

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By J. C. Uy, A. A. Burr

IN the primary solid solutions of zirconium-base alloys, there is a striking regularity of the effect of solute valence on the stabilization of the allotropic phases.1 The valences derived by pauling2 are for elements as they are bonded in the solid metallic state. Effects of variations in isotopes, alloying elements, and allotropes on their valences are difficult to determine and such data are presently unavailable. Pauling's values are somewhat empirical and approximate, but if some definite correlations can be found between those values and experimental observations, this will lend support to the tacit assumption that the possible variations in valence mentioned above are small. Pauling has amassed a large amount of evidence of such correlations. It is the purpose of this technical note to show another application of the Pauling valences and to offer a possible explanation for this observation. The relationship between the Pauling metallic valence of the solute and the stabilization of allotropic phases in zirconium is shown in Table I, which has been compiled from available data in the literature3 plus the results of work done at Rens-selaer Polvtechnic Institute.' The chemical valences are included for comparison. It can be seen that a solute whose metallic valence is lower than that of the solvent tends to stabilize the a phase while one whose metallic valence is higher than that of the solvent tends to stabilize the 0 phase. It should be noted that, inasmuch as the Pauling valences are periodic with atomic number, this is tantamount to saying that the elements in groups I-A, 11-A, III-A, III-B, IV-B, V-B, and VI-B are a stabilizers while those in groups IV-A, V-A, VI-A, VII-A, VIII-A, I-B, and 11-B are ß stabilizers. The chemical valences do not show such consistency. Although the zirconium-rich end of the Zr-Au diagram is not available, it call be expected that gold, having a metallic valence of 5.56, would stabilize the ß phase. At absolute zero, the Fermi energy level is the criterion of equilibrium, i.e., the structure having the lower Fermi level will be more stable. Conse- quently, allotropic transformation occurs in a metal when thermal excitation raises the Fermi level to a point at which the atoms can be better accomodated by a different structure which yields a lower Fermi level.4-6 Thus in allotropic transformation, a change in structure occurs as a result of the change in the energies of the bonding electrons. Since the Pauling valence is the number of bonding electrons per atom, and these are the only electrons whose energies are affected by thermal excitation,* it can be inferred that the introduction of a solute which has a higher Pauling valence than that of the solvent raises the initial Fermi level; consequently, the transformation temperature is lowered. The converse is also true. The fact that at the transformation temperatures this statement is still fairly valid implies that the contribution due to the difference in specific heat terms of the two allotropes is comparatively small.

Jan 1, 1962

By Carl M. Fellman

LABOR disputes caused considerable turbulence in the coal mining industry during 1946. As an outcome of these disputes, a definitely fundamental change in safety procedure was instituted: establishment of safety regultions for coal mines through the agency of agreements between the miners' union and the agency or agencies operating the coal mines. Although a temporary plan at present, the future will determine the. extent to which it may become permanent. Notwithstanding the turmoil in the industry extending through much of the year, the safety record for the first eleven months of 1946 was the best in the history of the industry for that period. The fatality rate for 1946 is lower than in any other year in the history of coal mining in the United States. This follows a pattern inasmuch as new low coal-mine fatality records were also made in 1945, 1944, and 1943. The five-year period 1942 to 1946 inclusive has a coal-mining fatality rate far lower than any other five-year period in the history of the industry. It is significant that this period exactly coincides with the operation of Federal coal mine inspection which got under way early in 1942.

Jan 1, 1947

By AIME AIME

ARGUMENTS and discussions were not lacking either Wednesday or Thursday mornings, when the geophysicists got together. The first session, under the chairmanship of Paul Weaver, was devoted largely to theoretical papers, except for the first one by F. W. Lee, which was a progress report. This speaker mentioned some of the high lights of geophysical exploration during the last year, such as the recently announced extension of the Rand gold fields through magnetic exploration, and the continued activity in the oil fields of this country. Even this brought forth some disagreements, Paul Weaver feeling that credit was being given geophysics where it was not due for the discovery of certain oil fields. In this criticism Everette DeGolyer concurred, and both agreed that geophysicists must lean over backward when it comes to taking credit for discoveries. The troublesome question of interpreting resistivity curves is always being aired, and Lynn G. Howell's paper, presented briefly by the chairman, served to clear up a moot point raised last year by M. King Hubbert's work. By use of Maxwell's theory of images the author calculated that the effect of a thin, conductive sheet placed perpendicularly across the middle of a four electrode system should bring the resistivity curve up to a figure equivalent to the resistivity of the surrounding medium, but no higher. Variations from this he explained as being due to dirt on the surface of the sheet. The difficult question of interpreting three-layer curves was tackled bravely in Thomas Manhart's paper, presented in abstract by S. F. Kelly. The author seems to be attaining some success through dividing three-layer curves into two approximation curves of the two-layer type.

Jan 1, 1933

By Julian E. Tobey

A MEMORABLE year has just passed in the field of coal utilization. Because of the war, oil conversions in industrial, commercial, and domestic installations have been made to the equivalent of 20,000,000 tons of coal. The war emergency has resulted in a great shifting of various types of coals to various markets. Huge tonnages of metallurgical-quality coals have been withdrawn from steam and domestic business and sent into the iron and steel industries. Marginal coals have replaced these coals in the steam and domestic field.

Jan 1, 1944

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Samuel Daniels

THE Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such con¬dition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400° to 600° F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400° F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600° F., the AI-Cu-Fe-Mg alloy at about 700° F. The former starts to reharden at 700° F., the latter at 800° F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500° and of 700° F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500° and 700° F. Although the latter can be made harder initially than the AI-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. CERTAIN aluminum alloys have been used for pistons and other parts operating at temperatures up to 650° F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance o corrosion. In the piston, the inertia forces and the bearing loading and with this the vibration are decreased. The piston head functions at a lower temperature (about 200° F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design.

Jan 2, 1926

By Hans Lundberq

WHEN geophysical methods were first employed in the search for ore deposits and oil accumulations, it was hoped that they would provide a direct means of locating such concentrations. Magnetized needles were used long ago in prospecting for magnetic iron ore, and soon after the discovery of galvanism in about 1790 attempts were made to find concentrations of valuable minerals electrically. Evidence indicating that the early geophyeical instruments were regarded merely as improved divining or dowsing rods is to be seen in the names "mineral finders," "ore finders," etc., that were applied to them. Today, appellations of this kind raise serious doubts in informed minds as to the intelligence and integrity of individuals advocating the use of such euphemistically named methods or instruments, for experience and research have shown that, geophysical, it is never a question of directly locating a given mineral but merely of delimiting its possible occurrence.

Jan 1, 1939

By E. A. Holbrook

MINING Metallurgy, and Petroleum Engineering department in our colleges are facing a crisis; indeed, conditions that threaten their very existence. Unless the Army, Navy, and War Manpower Commission change their present policy, within two years mineral industries education as now carried on will die, because no ablebodied students will be left in the course. If this is the decision of our responsible governmental agencies we of the mining schools must perhaps accept it as a war measure. It might be well however, for the executive of our mining metallurgical, and oil companies to look ahead a, to where they are to recruit a supply of young technically trained engineers. You can no more operate a mine, a steel plant or an oil company without trained engineers than you can operate a battleship without mechanical and electrical engineers.

Jan 1, 1943

By R. A. Morse, C. R. Stewart, F. F. Craig

This paper preFents the results of a series of model flow test on a number of large limestone cores, having different pore configurations. For limestone cores having substantially sandstone type porosity, the production characteristics for solution and external gas drives are similar. For cores whose pore spaces were microscopically heterogeneous (i.e., consisted of combinations of solution cavities, matrix. and fissures), the production characteristics lor solution and external gas drives vary widely. The degree of divergence between gas-oil relative permeability relationships calculated from solution or external gas drive tests is an indication of heterogeneity of rock pore structure. The results of water floods on cores depleted by solution gas drive for each of these two general types of limestone porosity are also shown. Generalizations are made on the water flood recovery that could be expected from each of these two types of limestone porosity. The similarity between solution drive field performance and model solution drive performance on cores from the same formation is shown for several cases. This indicate? the feasibility of predetermining limestone field performance from such large core tests. Photomicrographs of plastic-impregnated rock thin sections of the samples tested are presented as an aid in understanding the flow test performances. INTRODUCTION During the past 15 years. reservoir engineers and research workers have developed methods of testing rock and fluid samples and applying the results, through calculation, to allow reasonably satisfactory predictions of oil recoveries and performances to be expected in sandstone oil recervoirs. It has been determined that representative fluid flow data can be obtained on rock samples as small as three-fourths in. in diameter by one in. long in most sandstones. However, little has been accomplished toward the laboratory determination of fluid flow characteristics in limestones. There has been a great deal of speculation as to the influence of variations in pore size, shape, and degree of interconnection upon oil recovery processes, and a great deal of thought has been given to the interpretation of limestone field perfomance. It has been generally recognized that predictions of reservoir performance based on oil displacement tests on small limestone core samples the size of those used for sandstone tests can often be misleading because of the improbability of obtaining a representative sample in such a small core. Obviously, if there are present in the rock, pore openings of the magnitude of 1/16 in., or fractures or solution channels up to one in. or more in length, it will be impossible to cut any sample less than one in. in any dimension which would represent the flow geometry of the gross rock system. In some formations, the individual openings in the rock are of such size that it would be impossible to obtain a good sample of the flow system even in the total core available from conventional-sized well cores. However, by increasing to the maximum the size of the sample used, it should be possible to obtain representative flow data from the majority of limestone reservoir materials which can be used for prediction of future primary production performance or response to be expected from secondary recovery measures. The only alternatives to obtaining good laboratory test data to serve these purposes are extrapolation of primary performance data obtained by partial depletion of a field, or obtaining information from pilot tests. It has been shown previously, and will be demonstrated further by the work reported in this paper, that extrapolation of solution gas drive performance for an estimate of gas injection response can be very misleading in reservoirs of heterogeneous type porosity. Although it cannot be expected that laboratory information can ever eliminate the necessity of small-scale pilot operations, it is expected, as is now the situation with sandstone reservoirs, that laboratory tests should provide reliable information for screening of

Jan 1, 1953

By E. Gybbon Spilsbury

The introduction of underground machinery in mines, and especially the invention of the rock drill, called attention to the necessity for some motive power to drive them. The use of steam generators underground is as a general thing inadmissible, owing to the difficulties of ventilation and the transportation of fuel, and the great loss of power by condensation in the pipes, when surface generators are used, added to the inconvenience of getting rid of the exhaust steam, has precluded the direct use of steam for this class of machinery. Water as a power has with very few exceptions proved a failure, owing to its weight and incompressibility, and therefore the attention of mining engineers has very naturally turned to the use of compressed air. This agent not only answers all the requirements for power, but has the double advantage of greatly assisting in thoroughly ventilating remote workings, and in cooling the underground atmosphere. It is therefore clear that the successful introduction of underground machinery is dependent on the economical production of good and efficient air-compressing machinery. Although many improvements have of late years been introduced in this class of machines, the most of them are open to serious objections, the chief of which are the very small duty they perform for the power expended, and their great expense, due to the complexity of their construction. This latter fault is the chief reason why the introduction of rock drills and other underground engines is so limited, as comparatively few mines can afford to expend the required capital for the installation of a complete compressing plant. But with the introduction of a cheap and effective compressor, there is no doubt that power drills will become as generally used in mines as the hand drills are now. The great excess of power required in most machines to compress air over that given out again by the use of the air thus compressed (amounting as it does in most cases to sixty per cent.) is well known to all mining engineers. Of course a portion of this loss is due to the friction of the air through the pipes, and will always occur however effective the machine used may be, but the chief cause of the

Jan 1, 1880

By L. E. Porter

The demand for crude oil on the Pacific Coast during the year 1945. was so acute that the California crude supply had to be augmented by tank-car imports from the Texas and Rocky Mountain fields. Crude imports reached a high of 64,800 bbl. per day during June, with a total of 14,259,000 bbl. imported during the first 11 .months. The U. S. Navy also implemented the crude output from California pools by drilling and completing approximately 300 wells in the Naval Petroleum Reserve No. 1 (Elk Hills), from which an established production of 65,000. bbl. per day was reached in late February and maintained until Aug. 17, 1945, when it was reduced to its preprogram level of 15,000 bbl. per day. Even with the conclusion of the Pacific war on V-J day (Aug. 14), the military petroleum product requirements have permitted little material reduction in output of California crude to prewar rates. During the year, a total of 327-760,000 bbl. of crude was produced, or 19 per cent of the total crude production within the United States during the same period, as compared with 310,996,000 bbl. or 18.4 per cent of the nation's crude production in 1944.

Jan 1, 1946

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By Paul A. Farrar, Harold Margolin

The Ti-Al-V system has been delineated from 50 to 100 wt pct Ti and front 600 to 1400°C by X-ray and ntetallographic techniques. Isothermal sections were delineated at 600, 700, 800, 900, 1000, 1100, 1200, 1300, and 1400°C. X-ray and metallographic evidence indicated the presence of two phases and in addition to those reported by previous investigators of the ternary system'-3. T HE titanium-rich region of the Ti-Al-V system as originally proposed by Rausch et UZ, and Jordan and Duwez3 was based on the binary Ti-Al diagram as proposed by Bumps et uZ. As additional phases have been shown to exist5-' in the region previously thought to be all a, the titanium-rich region of the Ti-Al-V system is open to serious question. Therefore, in order to determine the effect of the indicated changes in the Binary Ti-Al system on the ternary Ti-Al-V system the present investigation was initiated. EXPERIMENTAL PROCEDURE The experimental procedures in this investigation are the standard techniques used in the study of titanium-alloy systems which have been described in detail previously.1° Consequently, only details pertinent to the present work are discussed. The alloys employed for the delineation of this system were prepared from titanium obtained from the Bureau of Mines (73 BHN) 99.99 pct Al and 99.7 pct V, by the consumable arc-melting technique. The titanium was premelted into buttons of 25 g because spattering during the first melt caused uncontrollable loss of alloying constituents. Typical analyses of the material used have been reported elsewhere Attempts to hot roll the alloys prior to heat treatment were made on the first series of alloys prepared, but as the area of extensive hot workability was fairly restricted, see Table I, this practice was discontinued. The times of isothermal annealing are given in Table 11. A preliminary heat treatment of 96 hr at 1000°C was used prior to heat treatment at lower temperatures. The standard techniques used for polishing specimens involved belt-grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch. In the low-alloy region it was found that the oRo etch, developed by Ence and Margolin,o gave better contrast between phases. Where this procedure did not differentiate between phases clearly, the method of stain etching developed by Ence and was used. It has been previously reported15 that filing of titanium alloys is not desirable for producing X-ray powders, since the powder becomes contaminated by the file material. Therefore, for those samples not brittle enough to Crush, the procedure described below was used. The specimen was wrapped in molybdenum sheet and placed in a vacuum system and evacuated to 0.03 p. Palladium-pur if ied hydrogen was then admitted to the system until a partial pressure of 5o Cm of H was reached. The specimen was heated in the system to the temperature of original heat treatment and was slowly cooled over a period of 3 hr to 400°C while the partial pressure of hydrogen was maintained. The sample was removed from the system after it had completely cooled and was crushed to a powder of 230 to 270 mesh. The powder, wrapped in molybdenum sheet, was dehydrogenated at the temperature of original heat treatment until a partial pressure of 0.03 p was maintained in the system for at least 1/2 hr. The tube containing the powders was quenched in iced brine while still connected to the vacuum system. After dehydrogenation, the powder, except for the

Jan 1, 1962

By H. G. Turner

The coals mined in the area known as the anthracite fields of Pennsylvania have always been recognized commercially as anthracites. In the literature, however, some of these anthracites have been called semi-anthracites by various writers. The coals mined in Sullivan County, especially those from the Bernice field, have been recognized commercially both as anthracites and semi-anthracites. In the literature they have almost always been referred to as typical semianthracites, although Franklin Platt,1 in his report to the Pennsylvania Geological Survey, uses the terms semibituminous, semianthracite, and anthracite in describing them. The purpose of this paper is to endeavor to dispel the confusion of names used to describe these coals and to supply further information that will permit a logical and definite classification. Most of the confusion of the past has been due to the impossibility of securing enough fresh face samples from which to draw sound conclusions; some of it was due, no doubt, to lack of standard methods of analysis, and of course, to the ever-present lack of definition of boundaries from the standpoint of classification. Map Showing Lines of Equal Volatile Matter and Lines of Equal Specific Gravity As a foundation for this work the writer constructed a map showing lines of equal volatile matter and lines of equal specific gravity throughout the anthracite and semianthracite regions. The points on these lines were determined from a study of analyses of 214 face samples from 28 mines and composite analyses from 18 different breakers. These samples were collected through the joint efforts of the U. S. Bureau of Mines and the Anthracite Institute. The Bureau of Mines standard method of sampling was used in all cases. All analyses were made by the Bureau of Mines and are used here with its permission. The

Jan 1, 1934

By L. W. Eastwood

PART 1. EFFECT OF HEATING RATE UPON RECRYSTALLIZED GRAIN SIZE OF ALUMINUM AND ALUMINUM ALLOYS AMONG those concerned with the annealing and heat-treating of aluminum and aluminum alloys, it is well known that after cold-working a coarser grain is usually produced by slow heating than by more rapid heating. Consequently, for the control of the grain size produced by annealing or heat-treating cold-worked aluminum and aluminum alloys, the heating rate is of considerable practical importance. References in the current literature on the effect of heating rate are numerous, but it appears neither necessary nor desirable to give here a review of the former work done on this subject. It became evident during some preliminary work on the recrystalliza-tion of aluminum and aluminum alloys that the effect of heating rate depended upon the type of microstructure of the metal. This observation led to the following study of the relationship of the type of microstructure of the alloy to the effect of the heating rate.

Jan 1, 1939