Search Documents

By C. W. Thompson

The two-way belt conveyor for coal mine service simultaneously carries coal from faces and transports men and supplies into the mine, largely eliminating the necessity for rubber-tired supply and man haulage equipment and the necessity of maintaining additional headings. SINCE 1920 use of belt conveyor transportation has increased steadily, and capacity in tons per hour per unit has increased at about the same ratio. Belt conveyor systems for simultaneous two-way material transportation have been widely discussed, but heretofore have proved impractical for specific operations. Studies of a proposed means of disposing of wash-ery waste on the return trip of a main haulage conveyor, as yet uninstalled, led to the application of two-way belt haulage to Weirton's underground supply and mantrip problems. Except for a single-tracked main haulage entry, Weirton mine is essentially a full-belt haulage operation with attendant problems of supply and man-trip haulage that could not be handled with conventional belt conveyors during the regular work shift. It was necessary, therefore, to maintain rubber-tired haulage equipment and haulageways serving multiple-shift continuous operations. The conventional underground belt conveyor is primarily intended to transport coal from working faces to surface. Belts are usually reversed to haul men to face areas at the start of the working shift or to transport supplies. The two-way belt conveyor for coal mine service is not yet offered for sale as a unit by any manufacturer and must be built on order. This conveyor, with return run traveling parallel but opposite in direction to the outgoing or coal haulage run, permits not only haulage of coal from faces, but simultaneously permits transportation of men and supplies into the mine at any time, see Figs. 1 and 2. This eliminates, to a great extent, the necessity for rubber-tired supply and man haulage equipment and the maintenance of additional headings. Unlike conventional installations the return belt is in the open for inspection and maintenance. It is less subject to edge wear, since it runs on regular troughing idlers, see Fig. 3. The only points where the edge of the belt can rub are at the drive unit and the tail units where improved design should eventually eliminate edge wear entirely. Individual conveyor sections are lighter, since all that is needed is a tubular stringer on each side to carry troughing idlers only, no cover plates being necessary. The return run is carried on an assembly identical to that carrying the coal haulage run. These assemblies are definitely easier to handle and are cheaper than installations for the same length of conventional belt conveyor. The four pipes required for the complete conveyor frame may serve only as supports, or, with proper couplings, may be used for mine water discharge line, pressure line for face spraying, telephone cable conduit, or any other purpose requiring a pipe line, see Fig. 4. Additional expense, if any, for the increased number of pulleys needed to turn the belt over for the return service is more than offset by reduced expense for rubber-tired supply and mantrip haulage. The two-way belt haulage system is confined to a single heading on intake air, isolated from all other headings by stoppings on each side, and open for air circulation only at the main haulage way and at the faces. One additional heading, also on intake air, is maintained as an emergency rubber-tired haulage way, all other headings being center-posted and used as airways only until retreat work begins. This method, of course, can and should be used with any belt conveyor, since it provides two independent intake airways for escape in case of fire on the belt or elsewhere. Belt heading is heavily timbered even under good top conditions and space between the two runs permits center posting for the full length

Jan 1, 1954

By EDWARD B. DURHAH

(San Francisco Meeting, UCtober, 1911.) THE refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying more than 200 parts of precious metals in 1000, or, in mint parlance; over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum group that were in the bullion. This residue is relatively small, and is melted into bars and stored until sufficient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's office, laboratory, and generator-room, respectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Oct 1, 1911

By Thomas A. Wright

No symposium on die casting could be complete without consideration of the methods of formula and impurity control. No consideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. COMPOSITION Aluminum.-Aluminum die castings are expected to conform to the specifications of the American Society for Testing Materials1† and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven

Jan 1, 1935

By F. Julius Fohs

CENTRALLY located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis., because it and others of its immediate group exhibit the conditions characteristic of all. I. THE MEMPHIS MINE. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of some 350 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the bills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen.. A line of crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar-some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to limestone and calcite leaching, and the minute ones to the leaching of zinc-blende.

Apr 1, 1909

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950

By Alberto J. Terrones L.

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,1 by Barrel1 on Marysville, Mont.,2 and by Goldschmitt on the Oslo district, Norway,3 laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf4 made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control5 ore finding. Some years later Harrison Schmitt6 fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed.

Jan 3, 1958

By F. N. Koepel, L. A. Callaway

The property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, about 75 miles to the eastward from the port of Chafñaral. At this point the Andean system is made up of two principal ranges, and the mine and metallurgical plant are both on the westerly slope of the outer or western range. Mean elevation of the mine is 10,500 ft., while at the plant the elevation ranges from 9445 to 9700 ft. A meter gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 94 miles, of which 57.79 miles are owned by the Andes Copper Mining Co. and the remainder of the road is controlled by the State. Development of the Potrerillos mine and installation of the metallurgical equipment presented unusual difficulties due to the arid nature of the country, high altitude and remoteness of the location from any considerable center of population. As a primary step it was necessary that railroad transportation be provided in order that mine development and plant construction could go forward on an economical basis. Provision of an adequate supply of water for domestic and metallurgical uses involved the construction of approximately 178 miles of pipe lines, all of which have their sources at altitudes ranging from 12,000 to 14,000 ft. above sea level and traverse rough and difficult terrane. Water for metallurgical use is brought to Potrerillos from the Ola River, a stream originating in the high cordillera to the eastward from the property. It is delivered by means of a steel pipe line, 32 miles long, having diameters ranging from 22 to 36 in. Domestic water is supplied to the various camps through a system of pipe lines aggregating 146 miles in length, the Ola water being unfit for this purpose. These conductors gather water from numerous springs in the high mountains to the eastward from Potrerillos and deliver it to the mine, the reduction works and the port at Barquito. Extensive permanent housing facilities had to be provided as it was necessary to care for more than 3000 workmen and employees at the

Jan 1, 1934

By John V. Beall

When the mineral seekers came, they brought romance, excitement and, too often, transitory riches. It has been so for uncounted centuries. While the rich ore lasted, living was high and money flowed-mostly out of town. The whole creation was like a circus. The headframe went up like the center pole of the big top. The reduction works was an ingenious affair; an opportunity for self-expression by the mining engineer on the job. When the high grade gave out or the bottom dropped out of the market, the whole show folded. Machinery was scavenged for the next location. About all that was left were the raw footings, like giantsteps on the hillside; and the headframe above the silent diggings. Mostly, the people went away too. Arizona Territory was like that at the turn of the century. It can still happen. But, in copper, the age-old pattern has been disrupted. From Mineral Park in the northwest to Chino in the east and Cananea in the South, a growing number of companies have emerged-large, stable, productive. Southwest copper is truly a mighty industry, accounting for one fifth of world new copper production. In this period of scientific development, changes are fast, often dramatic. But even mining engineers, or possibly more so because they have an intimate knowledge of the industry, fail to appreciate the evolutionary changes that have shaped Southwest copper into what it is today.

Jan 10, 1965

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By John Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by com-bustion within the mass itself. Its first successful application, in connec-tion with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremen-dous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for ignit-ing purposes.

Jan 1, 1938

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

MR. Woo's succinct description of the mining and smelting of silver-lead in Mongolia, with the roasting-and-reduction process and cupellation, has much interest as a picture of methods that not only may have been in use, as he suggests, a thousand years ago, long before the existence of mining schools or chemical laboratories, but probably vary little, if at all, from the practice of prehistoric times, when King Priam's handsome silver vases, cups and bowls were formed. For it is highly improbable that such large objects were made from comparatively rare native silver, and the metal must have been smelted from ore, and most likely in great part from galena,, with cupellation of the lead. Dr. W. A. P. Martin, in his excellent book on the Lore of Cathay, points out that Chinese alchemy is over 2000 years old, antedating the European by at least six centuries; and he infers that the Chinese skill in metallurgy and many branches of practical chemistry owes its origin to " those early devotees of the experimental philosophy who passed their lives among the fumes of the alembic." Those alchemists, however, may have more likely derived some of their leading ideas from the mys terious, and at that time wholly unexplainable results observed in already very ancient metallurgical processes; in which, for example, certain stones were transmuted, as it were, into metals widely divergent in character from their ores, and even silver and gold were obtained from the most unlikely-looking mate rials. It is therefore, in any case, not improbable that the Chinese may have preceded western nations in the discovery of metallurgical methods. At all events, it is now evident that the Japanese acquired these arts from China, the former source of all their higher civilization. My own observation of old-fashioned silver-smelt ing at Hosokura, on the main island of Japan, and about 220

Jan 1, 1903

By J. G. EVANS

It is with a certain amount of trepidation that a man considers gathering his family of six, traveling across a continent, two oceans and a sea, and going to live in a foreign land. But "pioneering" is still possible, and a nation is "foreign" only until one has lived in it. We've had eight years of pleasant experiences in South Africa on which to base that contention. It was in January 1938 that my brother first extolled the virtues of South Africa to us, and just three months and a thousand small problems later my wife, two daughters, three sons and I were boarding a ship in New York, bound for Cape- town. We arrived in May, and within a week had found a furnished home with beautiful lawns, tennis, court, a garden, and everything needed for family comfort. The children were soon located in school, and I settled down to the task of entering the importing business, as had been my original intention. The importing business started out slowly but was coming along nicely when on Sept. 3, 1939 the war started in Europe and a declaration of war by the Union of South Africa was made on the following day. With the declaration came import and export controls. In fact we were controlled completely out of business in one stroke. Liquidating the business, I went to Johannesburg intending to find work in one of the mines. Government health and safety regulations require that all underground mine employees have a red ticket from the Miners Phthisis Bureau certifying that they are not susceptible to silicosis, the scourge of the Witwatersrand gold mining industry. I made application to the Bureau, completed a form covering my whole past life, and was given a complete physical examination. The following day I was startled to find that I had not only been refused a red ticket but had been classified with a green ticket which for- ever bars one from working underground in any scheduled mine in the country, and all this in spite

Jan 1, 1949

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By Herbert A. Everest

The idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. , Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentagc expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2. Development, including all necessary .yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, draw-slate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the deadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high. The item, depreciation of coal reserves and royalties, is usually about

Jan 1, 1916

By J. Grosso, D. J. Nagel

In many metallurgical studies, it is necessary to reveal the composition and structural properties of materials. Usually this is done by etching, but some substances do not etch well or easily. Anodizing is known to provide an alternate treatment in many cases. In general, this technique is simple, often more sensitive to composition differences than etching, has excellent resolution, and provides variable contrast in those elements and alloys which anodize. Here we report the use of anodizing in diffusion studies in the TiCb system. Fig. 1 shows a cross section of the diffusion zone in a TiCb couple. The anodizing has clearly revealed both composition and crystallographic features. The maximum bulk penetration of the titanium into the columbium is marked by a sharp line because of the steep concentration gradient. The titanium grain size and orientation differences are also evident. Variation in the grain size reflects the gradually decreasing columbium concentration.

Jan 1, 1967

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By H. Rosenthal, A. L. Jamieson

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944