Search Documents

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble's results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By J. H. Zimmerman

JET-PIERCING experiments were first conducted over ten years ago underground at the Soudan mine of the Oliver Iron Mining Co. Results were successful enough to encourage further research. The next field tests were made on the Reserve Mining Co. property at Babbitt in 1941. These tests showed that blastholes could be produced in taconite ore by the use of a flame and proper fluxing agents. The war put a stop to the experimental program shortly after these tests. Extensive field tests were resumed at Babbitt in 1946. In these tests nominal 6-in. blastholes were produced at an average rate of 10 ft per hour. Rates as high as 17 ft per hour were obtained for short periods. The experimental equipment used resembles a portable rotary-drill rig mounted on a truck. The standard steel mast has been extended to 46 ft to accommodate a blowpipe capable of producing holes over 30 ft deep. All auxiliary equipment including winch for raising and lowering the blowpipe, drive motor for the rotary table, pumps and tanks for process fluids, electric power plant, and control instruments are mounted on the truck. The jet-piercing process consists of

Jan 1, 1948

By J. H. Scaff, H. C. Theuerer

Germanium may be reversibly converted from n to p type by heat treatment. Data for the conversion and the associated changes in resistreatment.tivity are given and the results are interpreted in terms of changes in the donor-acceptor balance. MEANS for controlling the electrical properties of germanium in a predictable manner are of interest because of the increasing utilization of this element as the semiconducting material in electrical devices. Since both the mechanism and the magnitude of the electrical conductivity depend upon the kind and quantity of impurities present, the conductivity usually is adjusted by first carefully purifying the germanium, and then, by standard alloying procedures, adding the elements desired. The elements usually added are from the third or fifth periodic groups depending upon whether p- or n-type germanium is desired. However, in the development of germanium rectifiers during the war, it was found that it was possible also to modify reversibly the conductivity of germanium and even to produce conversion from n to p type by heat treatment.1,5 Since then a detailed study of this effect has been made. The data are presented in this paper and an explanation is offered for the effects observed. Preparation and Experimental Procedure The method used in preparing the germanium ingots for this investigation has been previously described.' The method consists essentially of (1) reduction of GeO2* and (2) preparation of a 50-g ingot from the reduced material. Graphite containers are used in both steps. In the first step the GeO2 is reduced in hydrogen at 650 °C to form a sponge germanium which, to assure complete reduction and to obtain massive materials, is fused subsequently in the reduction furnace by gradually raising the temperature to 1000°C. The button of germanium thus obtained corresponds to a yield of 99.8 pct. The final ingot is prepared by fusion of the germanium button in a helium atmosphere. A cylindrical crucible in a vertical silica tube furnace is employed and the crucible is heated by an external induction coil. The ingot is solidified from the bottom upward by raising the induction coil at a constant rate with power to the coil kept at a fixed value. In such ingots, segregation is normal and most of the impurities are concentrated in the last region of the ingot to freeze. It follows then that the major portion of the ingot is purer than it would have been if freezing had occurred in a random fashion. Moreover the orderly advance of the freezing surface during solidification establishes in the ingot a succession of surfaces of constant composition, if it is assumed that the liquid is homogeneous and that diffusion in the solid is negligible. Therefore, some information on the distribution of impurities in the ingot may be acquired by determining the shape of the solid-liquid interface at different stages of solidification. This is of importance because the concentration of impurities will be seen to affect the response of germanium to heat treatment. Such information is difficult to acquire by direct means, for the impurities responsible for the electrical properties of germanium prepared in this way are present

Jan 1, 1952

By A. U. Seybolt, D. H. Haman

The rate of oxidation of the lowest nitride of chromium, Cr2N, was measured to be equal to the rate of oxidation of chromium metal. It was found that, while the presence of Cr2N in chromium does not affect the oxidation mechanism, a long exposure at high temperature affects the morphology of Cr2N in chromium, causing a massive internal nitriding along chromium pain boundaries. Marker expen' -ments showed that the rate of oxidation of Cr2N layers on chromium is determined by the rate of chromium diffusion through Cr,03. The rate of formation of Cr2N is determined by diffusion rate of nitrogen through Cr2N. This rate at 1000°C is around thirty times faster than the rate of oxiahtion. Evidence is presented which suggests that nitrogen from the air reaches the chromium through the Cr2O9 by migration through pores or cracks rather than by a diffusive process. IT has long been recognized that, when chromium or alloys containing substantial amounts of chromium are oxidized in air, some chromium nitride (Cr2N) is formed under the oxide scale. Although the presence of this nitride layer has often been described, there appears to have been no systematic study of the role played by the nitride during the oxidation process. Indeed, there have been conflicting re-ports'92 on the kinetics of oxidation of chromium and chromium alloys in air and in oxygen. However, it is now well-established'-5 that the rate-controlling process during the parabolic oxidation of chromium to Cr2O3 is chromium-ion diffusion through Cr2O3. Because of the importance of chromium-containing alloys as oxidation-resistant materials, it seemed desirable to investigate the behavior of chromium during oxidation with and without the presence of chromium nitride. Since a semicontinuous Cr2N layer forms relatively early during the oxidation of chromium in the air, chromium atoms must either pass out of or through the Cr2N layer to become incorporated in the growing Cr2O3 scale. Therefore, it seemed desirable to examine the oxidation behavior of the pure nitride. MATERIALS AND EXPERIMENTAL PROCEDURE The chromium used in this investigation consisted of slices of an ingot made from "five-nine" iodide chromium which had been argon-atmosphere melted in a Y2O 3-stabilized ZrO2 crucible in an induction furnace. The only impurity of any significance was 625 ppm of 0, which was usually reduced to a microscopically invisible amount by hydrogen annealing at 1400°C. However, one sample of chromium was used with the as-cast oxygen level as explained below. The samples were used after abrading through 600 Sic paper and then washing in toluene and alcohol. Both nitriding and oxidation experiments were performed in a vertical tube furnace connected to a glass vacuum system. 'This system was equipped with pressure measuring instruments for the range of 10 p to 1 atm, and a cartesian-diver pressure-control device was used in conjunction with a needle valve to allow control of pressure in the range of about 10 to 760 mm. The nitrogen or hydrogen gas was purified by passing through hot copper chips at 600°C, anhydrous calcium sulfate (Drierite), and liquid nitrogen. Oxygen gas was dried through the Drierite column and a dry-ice trap (-78°C). Changes in specimen weight were followed by a Pyrex helix used in conjunction with a cathetometer which could reproducibly be read to +0.001 cm, yielding an accuracy of about +0.2 mg. The spring was maintained in the cool upper part of the furnace tube where the temperature did not rise above about 35°C. The nitride in equilibrium with metallic chro-

Jan 1, 1964

By V. T. BERNER

THIS apparatus was designed primarily to meet the demand for a quick, efficient stopping to seal off the burning area temporarily during a mine fire, but it can be used in any circumstance where an immediate brattice is required for ventilation control. In using the old style brattice, mine-rescue workers have found it difficult, in smoke-laden drifts and stopes, to erect an effective stopping with wooden frame and canvas. Stulls must first be cut to the proper length, the canvas tacked in place, and the numerous irregularities of the walls and back must be caulked. This operation requires the employment of axes, saws, and hammers, which cannot easily and safely be handled in dense smoke. The fire fighters have often been forced to abandon their brattice, unfinished, because of the rapid approach of the fire, or because of the exhausted sup- ply of oxygen in their breathing apparatus. It is neces-

Jan 1, 1930

By F. F. McINTOSH

STEEL is a general name applied to the alloys of iron and carbon. These alloys always contain , other elements such as manganese, silicon, sulfur, and phosphorus. Manganese and silicon are usually considered to be alloying elements. Sulfur and phosphorus are regarded as impurities. Tradition has damned them both and, in addition to classifying them as impurities, has established the general impression that many of the ills of steels are the result of the presence of one or both of these elements. Metallurgists are inclined to question the soundness of this tradition. The fact that one blast-furnace plant is devoted entirely to the production of ferro-phosphorus which is used to rephosphorize basic open-hearth steel, and that sulfur is added to many heats of steel, indicates that these so- called impurities might also be classed as alloying elements, and that the tradition which damns them may not be altogether fair and well founded. A critical search through the technical literature on the effect of phosphorus on steel will disclose many references to its harmful effect. Most of these are general in character, but there has been a strong tendency to accept this traditional belief in the harmful effect of the element.

Jan 1, 1926

By M. S. Klima, P. T. Luckie

An evaluation of the operating performance of a recently designed pneumatic centrifugal classifier is presented. This classifier has been modified from a separate air and feed input design to an entrained solids in air feed input. The evaluation first required determining the size distributions for the three streams (feed, fine, and coarse). Using size distribution data and mass flow rates, a size selectivity curve was calculated for each operating condition tested. This curve, in turn, was characterized by appropriate selectivity parameters (i.e., the equiprobable or cut size, the sharpness index, and the apparent bypass values). The variation of these parameters with classifier operating conditions was examined. From these evaluations, the "best" operating conditions for the classifier were then determined.

Jan 1, 1985

AS I told you before in the treatise on ores, once these are found (whether they are ores of metals or semiminerals) it is necessary to assay them in order to know what is in them, since the judgment of the sight is not sufficient for recognizing the quantity or even what substance they contain. For this reason, it is necessary to come to assaying and, with the knowledge of experience, to weigh their virtues and to proceed with the work or withdraw from it and its expense; and also through knowledge to make provision for their defects if some evilness harms the ores. For if you should have need of a thing that would help them and should not find it, all that you have done would be lost; and, on the other hand, if you should find that the ores are abundant and rich and easy to smelt, you take courage to continue without respect for anything. Therefore, in the following book I shall tell you first in general how the assay of all the metals should be made. I shall enlarge in particular on silver more than on any of the others since it is more important. Then I shall tell you how the ores should be prepared for smelting and also how blast furnaces and other furnaces for smelting such ores should be constructed, and finally how all elemental mixtures of metals are to be separated one from the other with the ability and power of art, and how they are reduced to their final perfection and fineness according to their species.

Jan 1, 1942

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines' and the School of Mines at the University of Minnesota' have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By Julien Deby

THE sinking of a deep shaft is always a serious undertaking, especially when the strata to be traversed are of great hardness, or when they are feebly coherent or highly saturated with water. In the, first case, that of solid rock, modern appliances, such as the rock-drill, put into motion by air-compressors, along with suitable explosives, will generally answer the purposes of the mining engineer until he has reached the main water-levels. When these have

Jan 1, 1877

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

In an earlier study at this laboratory,' the authors investigated the solid solubility of holmium in copper, silver, and gold, and also the melting point of the first eutectic on the noble-metal-rich side in these systems. In a more recent study of the solubility of rare-earth metals in gold at this laboratory. Rider, Gschneidner, and McMasters2 noted that the reported eutectic temperature in the Ho-Au system was lower than the corresponding eutectics in systems of dysprosium and erbium with gold. A redetermination of the eutectic temperature in the Ho-Au system with the same alloy used in the original study showed the eutectic temperature to be 810°C instead of 778°C as originally reported. (The eutectic temperatures in the Ho-Ag and Ho-Cu systems were also redetermined and were found to be 795" and 864°C compared to 787° and 868°C, respectively, which were reported originally.) Since this large change in eutectic temperature made the solubility data appear questionable, new alloys were prepared, heat-treated, and examined metallographically. The procedure of sample preparation and heat treatment used in the original work' was followed except longer heat treatments were used ranging from 7 days at 600°C to 6 hr at 900°C. The results obtained are shown in Fig. 1. There is good agreement between the two studies in the maximum solubility of holmium in gold. Since the slope of the solvus is less pronounced in the present study, the extrapolation to 550°C shows a solubility of 1.6 wt pct Ho in gold compared with 1.0 wt pct in the original work. Since additional data were obtained and longer heat treatments were used in the present study, the larger value is believed to be more accurate. The authors wish to express their appreciation to P. Rider and K. A. Gschneidner. Jr., for bringing this discrepancy to their attention, and also to D. Thompson for assisting in the present study.

Jan 1, 1965

By Gregory Dybalski

The purpose of this paper is to illustrate the forecast capability of the econometric model of the cobalt industry1/ as utilized by the Federal Preparedness Agency. Forecasts from this model are illustrated from the premise that the leading producer continues production of cobalt. An alternate forecast is presented where the model structure is altered to reflect the condition where the leading producer leaves the market. All estimations and forecasts presented here are shown for illustrative purposes. The cobalt industry is highly concentrated; one company, owned by the Zaire government, accounts for approximately three-fifths of world production. The cobalt supply outside of Zaire is determined by the level of activity of copper or nickel markets, as cobalt is mined as a by-product of copper or nickel. The demand for cobalt reflects a diversified usage pattern; cobalt is used mainly in heat and corrosion-resistant materials, high- strength materials and permanent magnets. According to 1974 U.S. consumption data superalloys accounted for 22%, magnetic alloys 18%, cutting and wear-resistant materials 13%, and catalyst 7%. Foreign consumption is probably similar in terms of usage categories, but the relative order of the categories is in variance.2/ The Cobalt Model The cobalt model's object is to explain consumption, supply and price movements by utilizing statistically estimated equations. Central to the econometric model is the role of Zaire as the profit-maximizing "dominant firm". Zaire sets the price that is most profitable for itself. The price of cobalt depends on industrial demand, production of other firms, and net exogenous purchases, such as government

Jan 1, 1977

By L. E. Porter

El Segundo field is about 14 miles southwest of the central portion of the city of Los Angeles, immediately adjacent to the town of El Segundo and the Standard Oil Company's El Segundo refinery site. The field is served and bisected by several major highways connecting the beach cities on the west side of the Los Angeles Basin. The exact location of the field and its position with respect to other producing areas is shown on the map covering this portion of the Basin (Fig. I). The Republic Petroleum Co. discovered the first commercial production in the area when it completed its El Segundo No. 1 (sec. 18, T. 3 S. R. 14 W.) at a depth of 7402 ft. on Aug. 24, 1935, flowing at the rate of about 400 bbl. per day, 28" gravity oil. The producing horizon in this well consists of about 72 ft. of conglomerate and schist conglomerate situated below the nodular shale (Miocene). The true (or solid) schist (Franciscan) was encountered and penetrated some 20 ft. in the bottom of the hole. This paper gives a report on the history of development and oil production to date, and also submits the writer's interpretation of structural conditions as determined from such development. The limited development, together with the complex and variable nature of the producing horizon, makes any interpretation of the structure at present only tentative, and any forecast for a given well extremely hazardous. History of Oil and Gas Production The El Segundo field has produced approximately 1,920,000 bbl. of oil. It has 27 producing wells and 14 drilling wells or locations. The present daily rate of production is about 13,400 bbl. The production history of the field to date is shown in Table 1. The principal companies operating or owning leases in this field are: Caminol Company, Geo. F. Getty, Inc., Ohio Oil Co., Republic Petroleum Co., Pacific Western Oil Corporation, Royalty Service Corporation, Richfield Oil Corporation, Standard Oil Company of California, The Texas Company, Union Oil Company.

Jan 1, 1938

By John A. Church

When, in 1879,I examined the mines of the Tombstone Mill and Mining Company, at Tombstone, Arizona, I found a bed of tailings containing 12,000 tons, which had a value of 9 to 12 ounces of silver per ton and some gold. The ore had been amalgamated in pans, in which each charge had been ground for four hours, having been pre viously stamped through rough-punched screens, which gave a pro duct varying from 1-100th to 1-20th of an inch, according to the state of wear of the screen. It was certain that a large proportion of the tailings must be in fine slimes, and the question of recovering their value was difficult. Even now the concentration of slimes is . an unwelcome task, and at that day very little was known about it. Nevertheless, after considering the results of a test by repanning the tailings, I advised the company to concentrate and smelt, although they had to face the difficulty of making a smelting-product from slimes containing only 3 per cent. of lead. Limestone was abundant enough, but no iron suitable for flux was to be had for hundreds of miles. One of the company's claims con tained an argeutiferous manganese-ore, which gave but poor results by amalgamation. This was one reason for recommending smelt ing ; for if manganese would play the part of a precipitant, as iron does, the company could smelt by combining two of its silver ores, without other flux than the small amount of lime that might be needed. At that time no smelter had ventured to trust manga nese as a precipitant, though large quantities of this ore containing silver were bought and used by custom-smelters, who looked upon the manganese solely as a basic flux for silica. I believe that no other furnace has been obliged to trust this metal, and that the man ganese practice of Tombstone remains unique among the records of smelting lead-ores in the shaft-furnace. The bright side of the problem was given by the fact that the mines were shallow and that the enterprise would at least begin with oxidized ores. The tailings contained about 85 per cent. of silica,

Jan 1, 1895

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200' C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

By J. F. Myers, F. M. Lewis

IN the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kind to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent nonsulphide material. It is not the purpose of this paper to discuss the nature of these various oxygensulphur compounds nor their effect on flotation, but to describe a method for [ ] correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.1 From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1946

By Marcus Grossmann

THIS paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, 'the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of Chromium, Per Cent FIG. 1.-IRON-CARBON DIAGRAM. FIG. 2.-IRON-CHROMIUM DIAGRAM. alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron.

Jan 12, 1926

By J. P. Sheeha, W. F. Craig, M. Baeyertz

The loss in toughness caused by phosphorus within commercial ranges was studied in AISI-SAE 1340 steel and in molybdenum modifications of this grade. The replacement of part of the manganese by molybdenum in amounts which maintain the hardenability of the standard 1340 grade was shown to counteract to a marked degree the detrimental effects of phosphorus. THIS paper deals with the effect of phosphorus on the toughness of 1340 steel and with the effect on toughness of replacing part of the manganese by molybdenum while retaining the same hardenability as that of 1340. In previous work1 a progressive decrease in toughness was observed when the phosphorus content of 5140 was raised from 0.020 to 0.036 pct; that is, from a moderate phosphorus level to one higher but yet within the AISI-SAE specification for this grade. The structural condition of the steel was tempered martensite. Toughness was evaluated by the transition temperature determined by V-notch Charpy tests. Replacement of a part of the chromium in 5140 by molybdenum provided a factor of safety against loss of toughness caused by phosphorus, especially where the steel was cooled slowly after tempering. Scope of the Study: In view of the improved tolerance for phosphorus obtained by replacing a part of the chromium in 5140 with molybdenum, it seemed desirable to investigate the possibility of obtaining similar improvement in 1340 by replacing part of the manganese with molybdenum. Heats were made at different phosphorus levels, in a series that began with 1340 and ended with steels containing 0.32 to 0.35 pct Mo with 0.82 and 0.90 pct Mn. The analyses of the heats are given in table I. In order to facilitate later discussion, the 1340 heats have been placed together in the order of increasing phosphorus content, and the molybdenum modifications have been grouped according to phosphorus

Jan 1, 1951

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, Graduate Colorado School of Mines. Four years' experience in West and Northwest. Two years with American Smelting and Refining Co. Wishes to join field party on geological work, mining or areal, where opportunity will be given to be of direct assistance to chief of party in solution of field problems. Age, 26. Unmarried. At liberty June 1. No. 342. Member, technical graduate, aged 30, with' 7 years' experience in concentrating and mining, desires a position of authority with reliable company. At present employed. No. 343. Member. Ambitious, energetic, tactful engineer, college graduate, married, aged 30, desires location with a large coal mining organization. Seven years with present employers -n middle west; has had broad experience in the past eight years on examination, development and construction; successful record in handling men. Position must carry responsible work and a future. Will go anywhere for proper opportunity. Exceptional references as to reliability, character and capacity for work. No. 344.

Jan 3, 1917