Search Documents

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By E. E. Bach

STATEMENT OF THE PROBLEM THE administration of industrial organization today embraces more than the cost of production and selling prices. Competition is deeper seated than mechanical devices, overhead charges, and a shrewd manipulation of the markets. Despite the "down-to-the-minute" equipment and the "last word in organization," it is quite evident that "capacity production" will be an unknown quantity until the workman is considered as a producer, in relation to his home, as he is now considered in relation to industry. Whether or not a man shall do an honest day's work is as much a psychological condition as it is a matter of physical strength or skill. His attitude toward his work each morning is determined, to a large degree, by the environment of his home. Whether this attitude, good or bad, obtains the day through will depend entirely upon the one fact as to whether the corporation which employs him does or does not differentiate between the mechanical factor and the human factor in industry. To be more specific, sociological work, under whatever name, should be of such a character as to influence the life of a workman in such a manner as to establish a cooperative interest in his work, foster within him a spirit of contentment in his home, lead him-so to employ his leisure time that he will not lower his efficiency as a workman, destroy his domestic happiness, or endanger his standing in the community as a citizen. While no fixed rules of procedure can well be formulated for the development of the work, yet definite lines of activities will readily present themselves as applicable to the individual needs of a community. This is especially true where community influences and agencies pertaining to general welfare are easily correlated.

Jan 2, 1918

By BLABIEY STEVENS

THE object of this paper is to present a theory of the formation of fissures which seems to be supported by all available data. The investigation is, in the main, an exact one, and irregularities of the rock-structure are generalized. From the conclusions drawn a general classification of fissures is made, and this should be of practical use in the comparison of mineral deposits. The theory also throws some light on the equilibrium of the earth's crust and the depth of action of surface-waters. Incidentally, additions are made to the theory of earthquake-slips. Former Theory. It has been previously pointed out that the '"jointing" of homogeneous rocks occurs in two sets of planes, at right angles to one another, and making angles of 45° with the directions of greatest and least principal stress.' The theory by which this fact is explained does not, however, account for fissures and faults, because normal faults are usually more vertically, and reverse faults more horizontally, inclined than 45°. The "jointing law" is based on the following axiom: "In a homogeneous mass under pressure, rupture must take place on the lines of maximum tangential stress." 2 This law applies, with fair approximation, to the tests on jointing which can be made in the laboratory, and as nearly as can be expected to the natural jointing-planes in rock-masses, where the stresses are not very great; but it entirely fails to account for fissure-fractures.

Aug 1, 1909

By J. J. Gilman

RECENT experiments have shown that the mar-tensite reaction in a standard tool steel is influenced by the history of the reacting austenite. The martensite reaction proceeds to a given extent at a higher temperature in austenite formed from an annealed spheroidal structure than it does in austenite formed from tempered martensite: that is to say, a prequench lowers the temperature range of the martensite reaction in this steel. Furthermore, a prequench alters the appearance of the martensite as compared to martensite formed from "virgin" austenite. The steel used for this work was a manganese nondeforming tool steel of the following composition: C, 0.85 pct; Mn, 1.43; Si, 0.23; Ni, 0.12; Cr, 0.59; and W, 0.59. A piece from a rolled bar was forged to Vz in. sq and annealed to a spheroidal structure. Disks 1/8 in. thick were used in the experiments. Several sets of the specimens were prepared and austenitized in lead at 1475°F. Three sets were held at 1475°F for 15 min, quenched in water, and immediately reheated to 1475°F. After this quench the three sets were held for 5 min, 30 min, and 3 hr, respectively, at 1475°F and then the individual specimens in each set were quenched in molten baths to 325", 300°, and 275ºF, respectively, and held for 15 sec. Immediately after the quenching treatments? the specimens were tempered at 600°F for 30 sec to darken the martensite and then were quenched in water. The holding times were short enough to avoid isothermal transformation. Three other sets of specimens were given the same final quenching treatments as the first three, but they were austenitized at 1475°F for 20 min, 35 min, and 3 hr and 15 min, respectively, without an intermediate water quench. The two individual specimens from each set were quenched together in order to eliminate quenching errors. Several experiments were run in this way but only the six sets referred to are described in detail because they all yielded essentially the same results. By means of the stated heat treatments the martensite reaction was investigated for: 1—austenite formed from an annealed structure, and 2— austenite formed from tempered martensite. The martensite reactions of the two types of austenite differed significantly. This is shown by Figs. 1 and 2. Comparison of the photographs on the left in Figs. 1 and 2 with those on the right shows that less martensite was formed by a quench to a given temperature from prequenched austenite than from austenite formed from an annealed structure, that is, the prequench suppressed the martensite reaction. The effect was observed for specimens austenitized 20 min, 35 min, and 3 hr and 15 min. A comparison of Figs. 1 and 2 shows that the martensite reactions in both sets of specimens occurred at lower temperatures with increased austenitization time. This was caused by the increased dissolution of residual carbides with time at 1475°F. However, the difference in amount of martensite formed in prequenched austenite as compared to virgin austenite was approximately the same for all three austenitization times. One further observation should be noted. The needles of the martensite formed from virgin austenite are somewhat longer on the average and show less of a tendency to cluster than those of martensite formed from prequenched austenite. This causes the martensite on the right in Figs. 1 and 2 to have a more acicular appearance than the martensite on the left. Since the sets of specimens used in this work were austenitized for identical total lengths of time and the effect of a prequench on the martensite reaction existed for specimens held at the austenitizing tem-

Jan 1, 1953

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

By H. C. Goodrich

THE earliest record of copper production from the state of Utah comes from "The Resources of Utah," by. Mr. Fabian, in 1872, wherein it is stated that the. Mammoth mine of East Tintic was located in 1870 and that the ores yielded a large percentage of copper, silver and gold. It is also stated that shipments had been made to Swansea, England, which assayed between $200 and $300 per ton. The Mammoth-Copperopolis mine was located in, 1870 and sold the year following to an English syndicate. Some copper was shipped to. England and in 1873 there was constructed a 15-stamp mill and two copper smelting furnaces; these were operated a few months and before the end of the year were closed down and the property sold for debt. . This property -vas reorganized in 1879 and is at the present day a producer, though its principal product now is lead and silver. While a certain amount of copper has always been coming from the various lead-silver camps of Utah, the real history of copper in Utah should start with the discovery of the mines in Bingham Canyon, located about 25 miles to the southwest from Salt Lake City.

Jan 1, 1925

By D. L. Katz, M. J. Rzasa

The derivations of three methods of computing the static pressure gradients in natural gas wells have been presented to show the assumptions made. Charts were developed from which the pressure gradients may be read when the well-head pressure, the well fluid gravity, depth, and the average well temperature are given. A chart for estimating the well fluid gravity from the condensate content and separator gas gravity is included. The effect of the increased average well temperature after flow on the calculation of the static pressure gradient is discussed. Introduction Reservoir pressures have been calculated from well-head pressures for gas wells for many years. As the pressure measurements become more accurate, the need for a reliable calculation of the static pressure gradient often arises. This paper will develop the several methods for computing the pressure gradient in gas wells and make a comparison between them. The method of calculating static pressure gradients in common use is Eq. I (ref. I) or its counterpart which includes a factor for the deviation of the gas from the ideal gas law. P2 - P1 = P1(e0.0000347GX _ I) Eq. [I] in which P1 = pressure at well head, lb. per sq. in. abs. PP = pressure at bottom of well, Ib. per sq. in. abs. G = gas gravity X = depth of well, ft. An alternate method is to compute the average density of the gas in the well and multiply by the well depth in a manner similar to that used for liquid gradients. Derivation of Formulas A static pressure gradient is a special case of the general fluid-flow equation. Consider a pound of fluid flowing in a vertical column from point I to point 2, Fig. I. By an energy balance for fluid flowing from I to 2: U1 + P1V1 + u12/2g + X1 + q = U2 + P2V2+ u22/2g+X2 +W [2] in which U = internal energy, ft-lb. per lb. P = pressure, lb. per sq. ft. V = volume, cu. ft. per lb. u = average linear velocity, ft. per sec. X = height above datum, fl. q = heat absorbed by fluid, ft-Ib. pcr lb. W = work done by system, ft-lb. per lb. An energy balance on the fluid itself gives: U = ?TdS - ?PdV + etc. [3] in which T = temperature, deg- R- S = entropy, ft-lb. per deg. R. per lb.

Jan 1, 1945

By F. W. Gordon

The Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three main stages of development in the accompnying drawings. Fig. 1 is the stove of 1869, the year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrake the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the restricted area of the passages and the many revervals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28' 6". Another reason mas that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22' X 28½' stove held the field for several yearn. A slight change made from this was to the 18' X 40' stove, where the height was increased, but the dumber of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little lea it was not any better. The next important change, seen in Fig. 2, was by increasing the height to GO feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decremed by alterllating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfactiou, but, although the proper doors were provided, it was very difticult to clean, owing to the long (distance the scrapers lid to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost mithotlt impairing in any yaw the

Jan 1, 1881

By G. L. Wilhelm

Prior to the construction of a 450 tpd concentrator at the Mayflower mine, owned by the New Park Mining Co. and operated by the Hecla Mining Co., the common mining methods were cut and fill, with waste or gob filling and square set timbering with waste fill. Stoping operations were beset with the usual problems related to waste filling methods- storage and handling of fill material from development, costly waste excavations necessary to obtain a portion of the needed waste rock, slow mining cycles due to filling and inefficient ground support. After Hecla Mining Co.'s successful utilization of sandfill in its mines in the Coeur d'Alene district, utilization of hydraulic fill in stoping operations at the Mayflower was a logical development of the modernization plan then in progress. The mine, located in the southeasterly part of the Park City mining district, Utah, is a medium size producer of lead and zinc ores, with gold, silver and copper as secondary minerals. The mine has been producing commercial ore since 1939 from a dual vein system which outcrops at an elevation of 7200 ft in the Wasatch Range. Access to the present mining areas is gained by a 7200-ft haulage tunnel and by an interior, three-compartment main shaft. The present mining horizons are about 2400 ft deep. The average horizontal cut and fill stopes, ranging from 3-15 ft wide and up to 120 ft long, can be classed as small.

Jan 5, 1968

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

By C. Fairhurst, A. M. Starfield

As a practicing mining engineer, I face many rock mechanics' problems daily and would like to mention one or two examples to illustrate the current gap between laboratory investigations and actual field problems. I would like to endorse Dr. Obert's suggestion that more field measurements and observations should be undertaken. There is an ever-increasing body of data beginning with Hast's results in Sweden,l then measurements at Elliot Lake, Canada, and so on, including our own measurements at White Pine, which clearly indicate that the horizontal stresses underground are often at least as large as the vertical stresses. Visual obsenation of the deformation of roof and pillars (including failure due to horizontal compression) also demonstrates that the horizontal stresses are often most important. Yet almost every laboratory investigation begins with the assumption that the only stresses acting are vertical. Roof spans in layered formations. for example, are calculated on the assumption that the rock behaves as a gravity loaded beam. This is all too often unrealistic. Roof bolts are also often considered to be simply means of suspending the gravity loaded beams. As Dr. Reed has mentioned they are probably, in fact, acting to restrain a beam which is attempting to buckle due to lateral pressure. The fact that moisture can reduce the strengths of some rocks as much as 50 percent has been known for many years. In the mine me are almost always faced with wet rock, yet no one has investigated ways in which this wakening effect can be overcome. as, for example, by waterproofing the rock. C. Fairhurst, University of Minnesota I would like to mention that we have found,2 from stress-relief determinations, that appreciable (over 1000 lb per sq in.) horizontal pressures occur also at the surface in granites quarried in central Minnesota. Whilst I agree that more field measurements are desirable, it is important to point out that most university research is undertaken by graduate students who must attend classes daily. Their research is therefore restricted to the laboratory. A.M. Starfield, University of Minnesota No one denies the importance of obtaining: data from field measurements. It is equally important, however, that field measurements be guided by theory. Much time and money can be wasted by indiscriminate measurement. An example of the value of theory in interpreting measurements is given in Dr. Obert's comments on the time dependent strain observed in a salt mine. He anticipated that the stress at the wall of the opening would change with time because salt is viscoelastic rather than elastic. It can be shown from theory that if an excavation in a viscoelastic medium is unsupported, then the stress at the wall does

Jan 1, 1967

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.' Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2'3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By H. A. Baumann, C. C. Wright, T. S. Spicer

A LTHOUGH the efficiency of coal utilization has A improved steadily since the turn of the century as a result of continued research and development, little of this increase in efficiency can be credited to improvements in the single retort stoker. There are still numerous problems connected with the burning of coal on this type of unit, the solution of which would be a stimulus to coal and stoker sales and a boon to the user. Among the more critical of these problems is that of burning slack bituminous coal of strong caking tendency and containing large percentages of fine material. With the increased trend toward mechanical mining, it may be expected that in the future an even larger percentage of the coal available for use on this class of stokers will contain higher percentages of the fine sizes, thus aggravating an already serious problem. During the war, the problem of efficient and economic burning of available coals on the single retort industrial stoker, particularly the class 4 stokers (301 to 1200 lb per hr), became quite critical in many localities. In addition to the inherent problems associated with the use of this class stoker, the coals available were frequently not those best suited for use on this equipment and the manpower shortage made it difficult as well as expensive for the consumer to provide the labor necessary to keep the iires in reasonably satisfactory condition. Although exact figures on the number of class 4 stokers are not available, the yearly tonnages of coal consumed are of considerable consequence and have been estimated* at between 15 and 20 million the stoker research staff of the Mineral Industries Experiment Station of The Pennsylvania State College was requested to study the performance of the single retort industrial stoker and to undertake a program of research on the more efficient burning of bituminous coal on this class of unit. Various aspects of overall problem have been investigated since the inception of this program in 1942, only one of which is here reported. General Considerations There are numerous factors which appear directly or indirectly to affect the overall performance of bituminous coal underfeed stokers, such as the caking or matting properties of the coal, the contact relationships between coal and air, the ash fusion characteristics, the burning rate, and the design of the stoker and furnace in which the coal is burned. An analysis of the influence of each of

Jan 1, 1951

By H. A. Baumann, T. S. Spicer, C. C. Wright

A LTHOUGH the efficiency of coal utilization has A improved steadily since the turn of the century as a result of continued research and development, little of this increase in efficiency can be credited to improvements in the single retort stoker. There are still numerous problems connected with the burning of coal on this type of unit, the solution of which would be a stimulus to coal and stoker sales and a boon to the user. Among the more critical of these problems is that of burning slack bituminous coal of strong caking tendency and containing large percentages of fine material. With the increased trend toward mechanical mining, it may be expected that in the future an even larger percentage of the coal available for use on this class of stokers will contain higher percentages of the fine sizes, thus aggravating an already serious problem. During the war, the problem of efficient and economic burning of available coals on the single retort industrial stoker, particularly the class 4 stokers (301 to 1200 lb per hr), became quite critical in many localities. In addition to the inherent problems associated with the use of this class stoker, the coals available were frequently not those best suited for use on this equipment and the manpower shortage made it difficult as well as expensive for the consumer to provide the labor necessary to keep the iires in reasonably satisfactory condition. Although exact figures on the number of class 4 stokers are not available, the yearly tonnages of coal consumed are of considerable consequence and have been estimated* at between 15 and 20 million the stoker research staff of the Mineral Industries Experiment Station of The Pennsylvania State College was requested to study the performance of the single retort industrial stoker and to undertake a program of research on the more efficient burning of bituminous coal on this class of unit. Various aspects of overall problem have been investigated since the inception of this program in 1942, only one of which is here reported. General Considerations There are numerous factors which appear directly or indirectly to affect the overall performance of bituminous coal underfeed stokers, such as the caking or matting properties of the coal, the contact relationships between coal and air, the ash fusion characteristics, the burning rate, and the design of the stoker and furnace in which the coal is burned. An analysis of the influence of each of

Jan 1, 1951

By J. K. Furst

THE reasons for manufacturing steel by the duplex process are, briefly: saving of time; increasing output for capital invested; and avoiding the difficulty sometimes experienced in obtaining scrap. On account of the latter reason, some plants duplex only at such times as the price and quantity of scrap in the open market warrant. At some plants the use of the duplex process enables, the blast-furnace practice to be simplified, because the furnaces run more smoothly and produce more iron when not held to a strict specification as to the silicon and phosphorus therein. The duplex process was practiced in Witkowitz as far back as 1878, but it was left to the steel makers of this country to develop it along practical, commercial lines. The American companies manufacturing steel by the duplex process at the present time are: Tennessee Coal, Iron & Railroad Co., Maryland Steel Co., Bethlehem Steel Co., Pennsylvania Steel Co.; Jones & Laughlin Steel Co., Colorado Fuel & Iron Co., Lacka-wanna Steel Co., Dominion Iron & Steel Co. of Canada. All of these companies, except the Dominion Iron & Steel Co., combine the acid Bessemer with the basic open-hearth process, while the latter combines the basic Bessemer with the basic open hearth. The Tennessee Coal, Iron & Railroad Co.'s Plant The installation of a converter of 15 tons capacity at the Ensley plant of the Tennessee Coal, Iron & Railroad Co. in 1904 marked the introduction into this country of the duplex system. The experience gained in the employment of the Bessemer converter had demonstrated that there was a shortening of .the time required in the open-hearth furnace and a reduction of the outlay for fuel and lime, thus affording substantial evidence of the economies resulting from this method.

Jan 10, 1914

By E. B. Hughes, F. G. Norris

Oxidation is characteristic of all processes for making steel from pig iron. This thought has been aptly expressed by H. W. Graham13 in the recent Howe Memorial Lecture, "The process of steel-making consists of using iron oxide to reduce the carbon content of the pig iron to the desired level." Direct oxidation refers to the reaction that results from introducing oxygen either alone or mixed with other gases directly into the steel bath. In working a heat, oxygen in some form is added to the steel to remove the undesirable constituents as oxides. There are two general methods of supplying this oxygen to the open hearth bath. The method in which the oxygen is added as a compound such as Con or iron ore is designated an indirect method because the steel bath must first decompose the compound to attain oxygen in a usable form. The other method in which oxygen is added to the bath in the elemental or gaseous form, more or less diluted by other gases such as nitrogen, is a direct method because no decomposition is necessary before the oxygen reacts with iron to form FeO which is dissolved in the bath in a usable form. Bubble formation (at least of a macroscopic size) presents no problem in case of direct oxidation because the reacting agent (oxygen) is in the form of bubbles when entering the metal. Regardless of whether oxygen is intro- duced into the bath directly or indirectly, several reactions proceed concurrently. In the presence of the bath of molten iron, FeO is formed either by oxidation of iron by oxygen or reduction of oxides by iron. This FeO dissolved in the molten iron is the source of oxygen for the oxidation of manganese, carbon, silicon, and phosphorus if these are present. The oxidation of carbon from steel is the controlling steelmaking reaction. The introduction of oxygen into the bath, its reaction in the elimination of impurities, and its control by the use of de-oxidizing additions have been subjects of importance since steel was first made by the bessemer process. Direct oxidation is, in a sense, an application of the bessemer principle to the open hearth process. Graham13 states: "The use of oxygen or air jets introduced into the metal bath is essentially an effort to approach in the open hearth the turbulence, rapid interface reaction, and high production rate per hour that exists in the bessemer process." The general subject, "Oxygen in Steel-making," was given new life by the studies of Herty and associates starting about1925. The current interest in elemental oxygen is intimately related to the large scale production of oxygen developed during the war period. Some of the first applications were made during the early summer of 1946 at the Steel Co. of Canada using oxygen with the fuel. Such a use is of considerable interest and importance in contributing to faster heats but is not the subject of the present discussion which deals entirely with the introduction of elemental oxygen directly into the open hearth bath.

Jan 1, 1949

By E. B. Hughes, F. G. Norris

Oxidation is characteristic of all processes for making steel from pig iron. This thought has been aptly expressed by H. W. Graham13 in the recent Howe Memorial Lecture, "The process of steel-making consists of using iron oxide to reduce the carbon content of the pig iron to the desired level." Direct oxidation refers to the reaction that results from introducing oxygen either alone or mixed with other gases directly into the steel bath. In working a heat, oxygen in some form is added to the steel to remove the undesirable constituents as oxides. There are two general methods of supplying this oxygen to the open hearth bath. The method in which the oxygen is added as a compound such as Con or iron ore is designated an indirect method because the steel bath must first decompose the compound to attain oxygen in a usable form. The other method in which oxygen is added to the bath in the elemental or gaseous form, more or less diluted by other gases such as nitrogen, is a direct method because no decomposition is necessary before the oxygen reacts with iron to form FeO which is dissolved in the bath in a usable form. Bubble formation (at least of a macroscopic size) presents no problem in case of direct oxidation because the reacting agent (oxygen) is in the form of bubbles when entering the metal. Regardless of whether oxygen is intro- duced into the bath directly or indirectly, several reactions proceed concurrently. In the presence of the bath of molten iron, FeO is formed either by oxidation of iron by oxygen or reduction of oxides by iron. This FeO dissolved in the molten iron is the source of oxygen for the oxidation of manganese, carbon, silicon, and phosphorus if these are present. The oxidation of carbon from steel is the controlling steelmaking reaction. The introduction of oxygen into the bath, its reaction in the elimination of impurities, and its control by the use of de-oxidizing additions have been subjects of importance since steel was first made by the bessemer process. Direct oxidation is, in a sense, an application of the bessemer principle to the open hearth process. Graham13 states: "The use of oxygen or air jets introduced into the metal bath is essentially an effort to approach in the open hearth the turbulence, rapid interface reaction, and high production rate per hour that exists in the bessemer process." The general subject, "Oxygen in Steel-making," was given new life by the studies of Herty and associates starting about1925. The current interest in elemental oxygen is intimately related to the large scale production of oxygen developed during the war period. Some of the first applications were made during the early summer of 1946 at the Steel Co. of Canada using oxygen with the fuel. Such a use is of considerable interest and importance in contributing to faster heats but is not the subject of the present discussion which deals entirely with the introduction of elemental oxygen directly into the open hearth bath.

Jan 1, 1949

[Separates of all the Technical Publications published in 1930 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions.] Metal Mining Technical Publi- Title Author Meeting Tran~. cation Volume No. and Page* 264-A.29 Quicksilver Industry in 1929. Im- L. H. Duschak San Francisco T30, 283, 319 provements in the Metallurgy of C. G. Maier and Oct., 1929 Quicksilver and Symposium on The others Present Status of the Quicksilver Industry (With Discussion) (37) 271-A.30 Observation on Ground Movement R. E. Palmer New York T30. 168 and Subsidences at Rio. Tinto Feb.. 1930 Mines, Spain (20) 274-A.31 Development and Installation of the C.L.Berrien New York T30, 139, 166 Hawkesworth Detachable Bit (29) Feb., 1930 276-A.32 Protective Measures . Against Gas 0. A. Glaeser New York T30, 129. 167 Hazards at United Verde Mine (11) Feb., 1930 287-A.33 Use and Cost of Compressed Air (12) R. S. Lewis New York Feb., 1930 314-A.34 Miami Copper Company Method of F. W. Maclcnnan New York T30, 39, YO Mining Low-grade Orebody (44) Feb., 1930 319-A.35 How Human Beings Respond to W. J. McConnell New York Changing Atmospheric Conditions Feb., 1930 (9) 324-A.36 Vertical and Incline Shaft Sinking at Arthur B. Foote San Francisco T30, 87 North Star Mine (21) Oct., 1929 32bA.37 Governmental Control of the Pro- W. E. Colby New York duction and Sale of Mineral Re- Feb.. 1930 sources (With Discussion) (16) 333-A.38 Some Recent Developments in Open- E. E. Hunner New York T30, 106, 117 pit Mining on the Mesabi Range Feb.. 1930 (25) 334-A.39 Mining Methods and Costs at Presi- V. D. Howbert El Paso dio Mine of American Metal Co. of R. Bosustow Oct., 1930 Texas (15) 339-A.40 Operation of Pressure Fans in Series W. 8. Weeks New York (8) V. 6. Grishkevich Feb., 1931 364-A.41 Top Slicing with Filling of Slices as H. Willey El Paso Used at the Charcas Unit of Com- Oct., 1930 pania Minera Asarco, S. A. (17) 373-A.42 Drill Sampling and Interpretation of H. T. Matson New York Sampling Results in the Copper G. A. Wallis Feb.. 1931 Fields of Northern Rhodesia (17)

Jan 1, 1930

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970