Search Documents

By William L. Fink and

Although age-hardening in an aluminum-base alloy containing magnesium was observed by Alfred Wilml as early as 1911, it was not until 1919 that a theory of the mechanism of age-hardening was proposed. Merica, Waltenberg and Scott12 studying the age-hardening characteristics of Duralumin at the National Bureau of Standards, came to the conclusion that age-hardening of this alloy is caused by the precipitation of CuAl2, which is less soluble at the aging temperature than at the solution heat-treating temperature. It was postulated that the initially precipitated particles were of fine colloidal dimensions but that they gradually grew in size. Maximum hardness was assumed to be attained when the particles reached a critical size. This theory was at first received skeptically, since it was a widely accepted view at that time that the solid solution state should represent the hardest state of an alloy. Shortly thereafter, Jeffries and Archer proposed their well-known slip interference theory.'13 They suggested that age-hardening was accomplished by the precipitated particles acting as keys interfering with slip along crystallographic glide planes. They showed that this mechanical theory led direct,ly to the assumption that maximum hardening would be produced by particles of a critical size, which they suggested would have a diameter approximately 10 times that of the aluminum atom. This contribution amplified and explained so rationally the age-hardening theory of Merica, Waltenberg and Scott that wide acceptance resulted. Objections to Simple Precipitation Theory From time to time certain experimental facts have been cited against the simple precipitation theory. The first of these was the discovery by Fraenkel4 that, although the electrical resistivity of Duralumin decreased during aging at higher temperatures (from 100' to 250' C.), it increased during aging at ordinary temperatures. This was not in accordance

Jan 1, 1940

By R. E. Crater

Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crystallographic directions, and in materials containing quartz because of the a-ß transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 3, 1959

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By M. King Hubbert

THE growth of human knowledge is an evolutionary process. His-torically our separate sciences came into existence as people became interested in various apparently unrelated domains of phenomena, and in this manner we acquired the sciences of physics, chemistry, astronomy, biology and geology. As various of these sciences became established, cognizance of them came to be taken by the universities and in this manner there arose the traditional departments of physics, astronomy, chemistry, biology and geology of our American universities. As there was no particular rationality in the boundaries separating the various sciences, in the university departments the jurisdiction of each has assumed quite arbitrary limits. In the domain of earth phenomena the first science to grow up was that of geology, which arose originally from the activities of the collectors of rocks, minerals and fossils. Thus geology evolved as a descriptive science dealing with directly observable terrestrial phenomena for which elementary rational explanations were offered. The traditional treat-ment of phenomena by the science of geology has rarely been with more than an elementary regard for the fact that these phenomena were also phenomena of physics and chemistry. Since the latter part of the nineteenth century, a new approach to terrestrial phenomena has been emerging and becoming of so great a significance that it can no longer be ignored. This approach has been made by people trained primarily in the sciences of physics and chemistry, who have investigated terrestrial phenomena as constituting phenomena of, their respective sciences. In this manner we have acquired the so-called "borderland sciences" of geophysics, the physics of the earth, and of geochemistry, the chemistry of the earth. Neither of these fields is new, having arisen chiefly at the hands of European investigators during the latter part of the nineteenth century. The European uni-versities have long since given official recognition at least to geophysics, by the establishment of departments or institutes of geophysics, which are on a par with ,the university departments of the other sciences.

Jan 1, 1938

By Edward I. Salkovitz

THE determination of the orientation of metal single crystals and the studies of plastic deformation are greatly facilitated by the use of the stereographic projection. To draw a standard projection of the crystal it is necessary to have a tabulation of the angles between the various crystal-lographic planes of the particular crystal studied. Bozorth' has published such a table for the cubic system which can be found in many reference books; such convenient tabulation for the hexagonal metals, however, does not appear to be in the literature, although scores of workers have calculated these angles. Therefore, Table I of angles for magnesium, zinc, and cadmium has been compiled. Since the c/a ratio is different for each of these metals, three separate calculations are necessary. The angles 4 between (HKIL) and (hkil) were calculated by means of the formula: Hh+Kk+½(Hk + hK)1+~3aLl cos The c/a ratios were calculated from data given in the 1948 edition of Metals Handbook. Fig. 1 is a typical (0001) standard projection of zinc. For all practical purposes, it serves for cadmium as well, as can be seen from the table. For magnesium, however, it is necessary to construct another net. R. M. Bozorth: Physical Review. (1925) 26, 390.

Jan 1, 1952

By Charles Legrand

The problem of mine pumping is so much affected by local conditions, and those conditions are so liable to changes during the life of a mine, that the best system to use is difficult to determine. The experience of the writer has been that, in general, for copper mines, electric pumping is most satisfactory unless the quantity of water to be pumped is great or the mine does not use electric power for any other purpose. As a rule, however, figuring on the cost of necessary power plant, the total cost of installation is greater with electric pumps than steam pumps. As the water is liable to be gritty, outside-packed plunger pumps are to be recommended, and if the water is not acid, or only slightly so, chilled cast-iron plungers pay for their extra cost very quickly in diminished cost of packing. With chilled plungers it is possible to use metallic packing instead of soft packing, if the water is not too gritty or the lift too high. In vertical pumps this packing is satisfactory for lifts up to 400 ft., in the experience of the writer, and may be found satisfactory for higher lifts. For water slightly acid, cement-lined pump bodies have given good satisfaction. For acid water, both plungers and puhp bodies should be made of acid-resisting bronze. For high lifts, especially with gritty water, a satisfactory pump valve is difficult to find. To reduce the unbalanced pressure on the valve at time of opening it is advisable to have narrow seats; this, however, brings high pressures on the seats when the valve is closed. On large valves for lifts of 600 to 1,000 ft. we have used leather, hard rubber, vulcanized fiber, and soft brass; for clear water the latter has given best satisfaction. The difficulties due to grit make it advisable to have large sumps where water can settle, and if possible, to have two of them so that they can be cleaned alternately. At the mines of the Old Dominion Copper Mining & Smelting Co., Globe, it was found that a small air ejector discharging into a mine car provides a very convenient way to clean mud and sand from a sump.

Jan 1, 1916

By C. R. Dodson, W. T. Cardwell

This paper presents the results of a theoretical and experimental study of the effect of preperforated liners on well productivity. The analysis concerns the rectangular type of slot, either machine or torch cut, which is common in California. Muskatla treated this problem recently in a mathematical analysis of the flow of oil or gas from natural reservoirs into both gun-perforated and slotted liners. This paper presents additional and simplified analytical considerations and conclusions for the slotted liner, the solutions being applicable in the laboratory as well as in the field. An application of the analytical methods to permeability measurements on mounted core samples is given, to show the effects of sealing wax or other obstructions on the end faces of the cores. Results Fig. I 'Ompares the results of some theoretical calculations with the results of electrical analogy experiments performed in the Standard Oil Company of California's Production Technology Laboratory at La Habra, California. Fig. I indicates that the flux into short, "three-dimensional slots" of the relative dimensions encountered in practice is approximately equal to that into full-length, "two-dimensional slots" having the same open fraction of pipe. (The same numbers of slot rows, and the same radius ratio are also implied.) It can be seen from physical considerations that the closeness of this approximation must improve as the ratio of the external radius to the internal radius increases. Therefore, it is possible to calculate the flow into a slotted liner using a simple modification of the Darcy equation: where N is .the number of slot rows and O is the open fraction of the pipe. Fig. 2 shows the results of calculations . using Eq. 28. The most remarkable features of Fig. 2 are the high flux values for very small open fractions of pipe. For instance, with six slot rows and a radius ratio of 500, 74 per cent of the open-hole flux may be obtained with only o.I per cent of pipe Open. Fig. 2 shows that for a given open frac tion of pipe, the flux is greater, the greater

Jan 1, 1945

By C. W. Parmalee

The ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its use except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample1 of coal commonly used in pottery ovens has something like this quantity of sulfur: total sulfur, 1.20 per cent.; sulfur in ash, 0.11 per cent.; volatile sulfur, 1.09 per cent." This is based on English pottery practice. Correspondence with a. number of leading manufacturers in this country has produced the following figures: Sanitary Ware.—(a) 1.0 per cent, maximum, (b) 0.5 per cent. Sewer Pipe.—(a) 1.2 per cent., (b) 1.1 per cent, present run, 3.0 per cent, has been used. Terra Cotta.—(a) 0.5 per cent, basis of contract, 1.0 per cent, approximate. Pottery.—1.0 per cent, contract, 1.5 per cent, probable content. Enameled Brick.—1.3 per cent, maximum, (a) and (6) designate different firms giving figures. Since a pottery kiln for sanitary ware will require about 14 tons of coal for a bum, the quantity of SO2 that will be generated from a 1-per

Jan 1, 1920

By Edward C. John, Wilbur H. Smith

At the Bingham Canyon pit operated by Kennecott's Utah Copper Division, the demand for geology has recently grown and diversified so rapidly that it has necessitated a revolution in geologic mapping techniques. The most significant changes in method have been in the preparation of the base map and in the computer application of collected data. Formerly maps were prepared by surveying with a transit or plane table. Now, however, a photogrammetric map with a scale of l in. to 200 ft is prepared semiannually and updated continuously to keep pace with the removal of more than 350,000 tons of material a day. Larger-scale bases of areas with specific problems such as un- stable slopes are prepared with aerial and terrestrial photography and photo-mosaics. Note sheets designed for computer application speed the processing of data. The multiplying applications of geology at the Bingham mine now include studies of the effect of structure, rock type, and alteration on slope stability, the relationship of sulfide mineral distribution to concentrating results, the effect of rock and mineral types on waste dump leaching, and the requirements of a reliable internal source of silica flux for smelting, as well as many others.

Jan 9, 1969

By Peter A. Allen

INTRODUCTION Lac Minerals Ltd., a significant North American producer of gold and other metals for over three decades, recently completed the financing for its third discovery in an eight year period. From 1975 to 1982, three important gold deposits in Quebec and Ontario: namely Bousquet, Doyon and Hemlo, were located and tested by company geologists. When current development plans are complete, Lac will have injected $400 million into these deposits. A discussion of these projects and their financing reveals some extraordinary challenges faced by top mining management. Responses to these challenges developed by Lac management may interest executives planning to proceed with new North American gold or base metal mines. MINE DE BOUSQUET In 1976, we explored a property containing a large low grade surface gold deposit. The geologial setting was exciting and we tested recent rethinking about the volcanigenic genesis of gold and base metal occurrences. These ideas helped pus to persist in drilling a nearby conductor and 600,000 ton, 0.22 ounce/ton orebody was outlined. With gold at $Cdn.150 per ounce the feasibility was approved and work started February 1978. Availability of a company custom mill 35 miles away reduced our immediate capital needs to $8.5 million. First of all, understanding the geological significance of results at Bousquet was critical. Mine and surface exploration geologists at Lac are continually and closely working together to better understand the nature of gold deposits in the Shield. This management emphasis on both pure and mine geology meant that a much larger ore reserve could confidently be predicted. (A proposal to quickly develop and ship the ore to a nearby company mine was discarded.) Instead of designing just for the initial plan of 500 tons per day we therefore included headframe, shaft and hoisting capacity for 1,700 tons and provided a compartment for future shaft deepening. These prebuilt additions were welcomed within two years. The type of collaboration whereby surface and mine geologists make study and field projects of each other's problems sets the foundation for this predictive ability. At Lac, the traditional responsibility for and supervision of the mine geologist by the mine manager is modified by this collaboration. This adds interest and scope to the geologist's work and lets him think beyond production requirements. Besides such management considerations, dedicated, professional geologists with integrity and lots of practical experience are needed to plan successful developments like Bousquet. Second, projecting future bullion revenue was critical and our experience selling production for future delivery gave us a way to ensure that loan repayment at term would not be jeopardized by falling metal prices. Output from a single mine is often reduced or curtailed for numerous reasons, so "selling forward" is done best and with least risk by companies like Lac with more than one or two producing locations for that metal. At first, a forward marketing program was considered unwise, speculative and unorthodox by analysts and other producers. Declining markets in the early 1980s prolonged gold project capital recoveries however, and critics were better able to appreciate the usefulness of such a tool. The notion that gold miners shouldn't sell forward is rooted in the belief that long-run gold prices will rise as modern social theory implementation in democracies inevitably erodes currency values. Selling against this trend goes against this industry belief or "ethic" and is at odds with the company shareholder who expects the gold price to rise not fall. Nonetheless, an efficient tool is available to the gold producer (not to most other metal producers) to quickly disengage from adverse price trends or to lock in spot prices instantaneously for two years or more of profits. Gold had recently retreated from U.S.$200 to $104 and now had reversed to $150. Lac had been forced to close several of its producers during the late 1960s because central bank-controlled

Jan 1, 1985

W. P. PUTNAM,. Detroit, Mich.-There is one company that is heating these tubes in an upright position by passing electrical energy directly through the tube itself. The lower connection is attached to an indicator, which shows the point at which the steel passes through the critical range At that point the clamps are released and the tube is dropped into a well of oil. This method simplifies the heat treatment of tubes in long lengths. H. J. FRENCH.-I am not entirely familiar with. the method outlined, but it appears to have one serious disadvantage; that is, the length of tubing that is directly connected with the electrical contacts is wasted and must be cut off due to either heavy oxidation or burning. That is a serious difficulty, if true in all cases, and cannot be overcome, inas-much as it is very difficult to draw long tubes of thin wall. Having once obtained a lot of tubes, to cut, say 14 ft. in length, there is often little excess metal available to discard. Am I correct concerning the burning or heavy oxidation of the metal where it comes in contact with the tube.

Jan 12, 1919

By R. L. Stegman, M. R. Achter

Nickel, fatigued in vacuum, shows intragranular crack initiation and growth at low temperatures. An increase in temperature initially prolongs fatigue life due to a more homogeneous distribution of slip. With a further temperature increase, the mode of failure undergoes a transitiotz to intergranular crack initiation with concurrent recrystallization which results in a shorter life. The transition temperature varies with bending strain and specimen purity. UNTIL recently, very little work has been done on the effect of temperature on the mechanism of fatigue and the resultant variation in fatigue life. Except for mild steel, where strain aging raises the strength at moderate temperature, fatigue lives had been shown to decrease with an increase in temperature. In their review article, Allen and Forrest' summarized the work of McCammon and Rosenberg and of Forrest and Mann on the fatigue of copper from -269" to 325°C. The fatigue life vs stress curves remained roughly parallel over this temperature range, the fatigue strength decreasing progressively with increasing temperature. When testing was done in vacuum, the present authors' found the results for nickel were different from those quoted above. Initially, the fatigue lives increased with temperature and then decreased as a grain boundary mode of failure was observed. The initial increase was attributed to a more homogeneous distribution of slip, a condition which was not as conducive to crack initiation as the bunching of slip lines observed at 20°C. Ronay, Reimann, and wood3 observed a similar change of slip line distribution in brass, tested in air, with rising temperature. Our previous observations were based on preliminary work with relatively few specimens, fatigued at comparatively low strains. To learn more about the mechanisms, the present investigation was undertaken for the purpose of studying systematically this effect over a wider range of strains and as a function of purity of the nickel. EXPERIMENTAL PROCEDURES The testing equipment, procedures, and specimen geometry have been described elsewhere.' An optical technique to measure bending strains was used as de-

Jan 1, 1968

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.' Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.' The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company's mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By H. L. Talbot, R. S. Young, A. Golledge

The differentiation of oxidized forms of lead from lead sulphide in complex products by chemical analysis is of considerable importance to certain mining and metallurgical companies. A method for the separation of "oxide" lead, (non-sulphide), from sulphide lead, based on the solubility of the former and virtual insolubility of the latter in concentrated ammonium acetate solution, has been employed for many years in the industry.1,2 Unfortunately this solvent, while satisfactory for lead sulphate and carbonate, is without action on lead phosphates or vanadates, with the result that at .Rhodesia Broken Hill Development Co. where these latter minerals are present, they have counted as sulphides when using this procedure. For the control of operations in the new concentrator it became necessary to have a closer check on sulphide lead than could be obtained by the only current method of differentiating this constituent from oxidized lead. For some time this problem has engaged our attention, and after a large number of solvents had been tried, the following procedure was evolved. Like all methods depending on selective solution in a com- plex material, it will not give 100 pct separation into oxide and sulphide portions. Because of the ease of oxidation of galena this is almost an impossibility. Our procedure will, however, give a recovery of 99-100 pct of the oxidized lead, contaminated with very small quantities of lead sulphide, and a corresponding recovery of 97-98 pct of the sulphide lead. The procedure is simple and reproducible, and gives results quite .satisfactory for routine control purposes. Experimental For this work standard samples of the following pure lead minerals were obtained from Broken Hill, Northern Rhodesia. These were hand-picked specimens, and were carefully ground to —200 mesh. Since it was realized that a fair-sized sample would be necessary for this work to thoroughly test the large number of procedures we had in mind, a compromise had to be effected between a few grams of very pure minerals and a large sample of lower grade material. For this work the presence of gangue was not deleterious, so long as the oxide lead minerals did not contain lead sulphide, and vice versa. Table I shows the lead minerals used, and their total lead content, both theoretical and actual. Apart from the pyro-morphite the minerals are seen by analysis to be quite pure. Many solutions were tried in an effort to dissolve the oxidized lead minerals and

Jan 1, 1949

By Y. A. Chang

Heat content values of tantalum monocarbide and tungsten monocarbide have been determined from 325" to 985°K by means of a drop-type diphenyl ether calorinzeter. Based on the values obtained in the present study and those available in the literature, best values lected and computed from 298. 15°K to temperatures close to their respectiue melting points. At temperatures higher than 1700°Kfor TaC and 27000 K for WC, values of Cp and related thermodynamic quantities were extrapolated based on the two Debye parameters: one corresponds to the metal sublattice and the other to the carbon sublattice. The contrzbutzon In the total specific heat due to lattice dilation was evaluated using the Nernst-Lindemann relalionship. The calculated values of Cp were in good agreement with the In view of their refractoriness, tantalum monocar-bide (TaC) and tungsten monocarbide (WC) are of con- experimentally determined ualues. Furthermore, the calculated values of the absolute entropies at 298.15"K were 5.03 and 4.15 in comparison to the experimental values of 5.05 and 4.15, all expressed in the unit of cal per degg-atom. Using the same Debye parameters, values of the linear coefficients of ther mal expansion for TaC and WC were calculated from absolute zero to their respective melting points using the Grüneisen equation. The calculated values are in excellent agreement with the experimental values available in the literature. Finally, the values of the bulk modulus of TaC from room tenzperature to temperature near its melting Point were also calculated using the equation recently derived by Anderson. No cot~ipari-son between the calculated and experimental values can be made due to lack of experimental data. siderable practical interest. In order to completely define these materials, it is necessary to know their thermal properties as a function of temperature. Tantalum rnonocarbide having a NaCl structure (B-1 type) melts congruently at 4250PK,1 while tungsten monoearbide with a simple hexagonal structure (Bh type) melts per itectically at 3049°K into melt and graphite.2 In the present study, the heat content values (from which

Jan 1, 1968

By P. G. Chamberlain, E. R. Podnieks, R. E. Thill

Although published data on the physical properties of rock are voluminous, information is often lacking on the environmental conditions under which such data were acquired. Efforts are frequently directed to improve specimen tolerances and preparation procedures; but investigators often overlook giving the rock environment equally careful control during the testing program. Generally, tests are conducted at existing laboratory room conditions, and the prepared rock specimens are frequently, if not most commonly, air-dried for various lengths of time before testing. The standard testing atmosphere recommended by the American Society for Testing & Materials (ASTM)1 is 73.4°F and 50% relative humidity. To maintain a rock at 50% relative humidity for testing purposes, however, requires special equipment and preconditioning procedures, as this study demonstrates. Relatively small variations in the moisture content of a specimen, for example, due to the coolants or lubricants used during specimen preparation, can cause significant variations in the physical properties measured. Such moisture variations may occur in the rock specimen even after it is air-dried, since laboratory humidity conditions commonly fluctuate from day to day. For these reasons, this study emphasizes procedures for preconditioning and maintaining a controlled environment during testing. Although the effects of moisture or temperature on rock properties have previously been studied, their combined effect on rock properties is unknown. In this study, uniaxial compressive strength, Young's and stiffness moduli, and longitudinal wave velocity were determined and compared under controlled conditions of temperature, moisture, and pressure for 11 environments considered to be of particular interest in laboratory, in-situ, and even simulated lunar environments. The following environments were selected for this program: -250°F under dry, 50%

Jan 1, 1972

By J. F. K. Brown

ANTHRACITE in 1943, in common with the coal industry as a whole, passed through a year of wage negotiations that seemed endless. In the early months discussion of the United Mine Workers' demands was taken up and carried on continuously until May, finally reaching an impasse when the Union refused to continue at work, while submitting their demands to the War Labor Board. Thus a strike threatened, averted by the Federal Government taking over the industry, effective May 1, by order of the President. An office of the Bureau of Mines was established in Wilkes-Barre under the direction of J. J. Forbes, Mineral Production Security Division, as regional manager, who conducted operations until September, 1943, when the collieries were turned back to the operators. But the miners did not agree with the War Labor Board's award rendered in the fall, resulting in a recurrence of the previously threatened strike. again averted by Government control. In addition to the major upsets, a number of individual suspensions occurred at various mines. In spite of these drawbacks, to which might be added the difficulty of obtaining equipment and the scarcity of man power, the industry by November was only little less than a million tons short of the previous year. and in all probability, finally produced but little less than in 1942. This little less. however, was greatly missed in the market.

Jan 1, 1944

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936