Search Documents

By B. E. Terkelsen, B. J. Piearcey

A study has been made of the effect of unidirectional solidification on the creep behavior, stress-rupture properties, and thermal shock resistance of four nickel-base superalloys. The alloys Mar-MZOO, B-1900, IN 100, and TRW 1900 show improved rupture ductility and thermal shock resistance when tested with the columnar grains parallel to the major stress axis during test. The relative improvement in creep-rupture properties depends on the intrinsic strength of the alloy, a property which depends on composition, heat-treatnient, and crystallographic orientation. The data clarifies some of the factors affecting the properlies of the cast nickel-base superalloy. COMPONENTS designed for high-temperature use have, in recent years, been fabricated by precision casting techniques using nickel-base alloys developed specifically for use in the conventionally cast condition. This development was a result of both the increasing complexity of the component and the recognition that high-temperature strength was incompatible with workability. The use of castings can be economically favorable, but, more important, the recent complex designs of air-cooled gas turbine blades and vanes in alloys which possess the necessary high-temperature strength cannot be forged. Common modes of failure of high-temperature components are excessive creep, creep rupture, and thermal fatigue. If rupture occurs then the mechanism is usually by inter crystalline cracking along those grain boundaries oriented transverse to the major stress axis. In the stronger alloys, rapid propagation of intercrystalline cracks result in apparent premature failure demonstrated by the absence of third stage creep in a creep-rupture test and low rupture ductility. Tensile ductility shows a similar trend, that is, decreasing ductility with increase in strength. It is not surprising, therefore, that increases in creep strength have only been obtained with a loss in resistance to thermal shock, a property which shows a dependence on tensile ductility. VerSnyder and ~uard' showed that the application of unidirectional solidification to a brittle Ni-Cr-A1 alloy both improved the rupture life of the alloy and increased rupture ductility. Since this casting method results in columnar grains, it appeared that the solution to the lack of ductility in nickel-base alloy components was the elimination of the source of failure, namely the transverse grain boundaries. This concept was recently developed2 to produce cast-to-size gas-turbine blades and vanes consisting entirely of columnar grains oriented parallel to the major stress axis of the component. Not only did the process impart increased rupture life and ductility to the components, but it also increased their resistance to thermal shock. During this development, the effect of unidirectional solidification on the properties of several alloys was investigated. The resulting data allows certain conclusions to be drawn regarding the factors affecting the creep and stress-rupture properties of the cast nickel-base superalloy and also its resistance to thermal shock. Detailed information was obtained on the alloys Mar-MZOO, B-1900, In 100, and TRW 1900. The composition of the alloys studied are shown in Table I. MATERIAL PREPARATION AND TESTING The conventionally cast alloys are cast as +-in.-diam bars in innoculated shell molds under conditions designed to maintain control of grain size. Unidirec-tionally solidified casting were produced in the form of 3-in.-diam ingots. Specimens from the latter were machined such that the axes of the columnar grains were parallel with the axis of the test bar, except in certain cases where the transverse properties of the material were being evaluated. The specimens were tested in an axial loading creep machine.' Temperatures were measured with thermocouples, attached just outside each end of the gage length, to assure uniform temperature along the entire specimen. Chromel/alumel thermocouples were used up to 1800"F and Pt/Pt-10 pct Rh thermocouples above 1800"F. The specimen temperature was recorded and maintained within i2"F throughout the test. Creep extensions were measured automatically with extenso-meters attached to ridges on the specimen and recorded continuously using linear variable differential transformers and multipoint recording equipment. MICROSTRUCTURE The microstructures of transverse sections of the four alloys studied are shown in Figs. 1 and 2. Fig. 1 shows optical micrographs of the alloys, both in the conventionally cast and unidirectionally solidified conditions. Each alloy displays a cored dendritic structure, a distribution of MC carbide, and the presence of the y — y' eutectic constituent.~ In the case of IN 100 and B-1900, Fig. 1 indicates that in these specimens the eutectic is degenerate. That is, it consists only of y' pools indicating that the y constituent has been solutioned during the cooling period after solidification. The major effect of unidirectional solidification on the microstructures of the alloys is a tendency to promote a more dendritic form of MC carbide and an increase in dendrite arm spacing, both effects being a result of the slower solidification rate in the unidirectional solidification technique. V, lec tron micrographs of transverse sections of the four alloys in the two cast conditions are shown in

Jan 1, 1968

By J. B. Scott, J. L. Popham, H. F. Coffer, J. J. Reynolds

This paper concerns field experiments to define the areal extent, orientation and thickness of an artificial fracture in the Sacatosa field, Maverick County, Tex. The fracture was made by a sand-oil treatment of 176,-000 gal of lease crude containing a fluid-loss additive and 270,000 lb of 20-40 mesh subangular Poteet sand. The well was perforated with a jet gun, consisting of six shots in a single plane. Fourteen test holes were drilled at various locations around the fractured well. Drill-stem tests, Micro and Sonic Logs, coring and sampling of formation cuttings were used to determine the presence of the fracture in these holes. The test holes were drilled at distances up to 250 ft in a radial pattern around the fractured well. In addition to fracture areal extent and orientation, sand grain size before and after fracturing, erosion of perforations and fracture thickness were studied. INTRODUCTION The orientation,12 areal extent3, 4 and thickness5-9 of artificially induced fractures in reservoir rock by hydraulic means have been discussed in great detail in the oil industry in recent years. Methods for initiating vertical"' and horizontal" fractures have been tested in the laboratory and the field. Although the methods used give successful well stimulation, good field data on the physical characteristics of the fracture are lacking in the literature. It is recognized generally that properties of a fracture, such as thickness, sand placement in the fracture" and shape, may vary from reservoir to reservoir. This paper gives data on size, orientation and sand placement in a large fracture initiated in a single plane in Sacatosa field, Maverick County, Tex. It is not intended as a speculative study; rather, it is restricted to actual field data on fracture properties. No attempt is made to prove that the same type of fracture occurs in all wells. The field procedure was to drill 14 test holes at various locations around the fractured well. By employing several different testing techniques, the presence of the fracture and some of its characteristics were determined. These techniques as well as the results obtained are discussed in detail in this paper. DESCRIPTION OF FRACTURE TREATMENT N. J. Chittim Well No. 37-1, completed in the San Miguel No. 1 sand, Sacatosa field, Maverick County, Tex., was chosen for the field study. The San Miguel sand is a tight, well consolidated sandstone with an average porosity of 23 per cent. The permeability ranges from 0.1 to 10 md, with a median permeability of 2.3 md. The sand thickness averages 23 ft and is located at depths of 1,150 to 1,700 ft throughout the field.I3 The fracture treatment performed on Well 37-1 was as follows. 1. The well was drilled to a depth of 1,438 ft with native mud, and 51/2-in. casing was set and cemented to the surface. 2. The casing was perforated at 1,349 ft with a fracture-initiating jet gun. This gun consists of six shots, 7/16-in. diameter in a single horizontal plane. The jets were oriented in two groups of three, 180" opposed. The perforating device was designed to initiate a fracture perpendicular to the wellbore.

By R. G. Lazzell

THE British are worried about the postwar possibilities of their coal mining industry. Indeed, there are causes for this worry, with the aver- age 1943 cost of production at about $5.40 per long ton, compared to $3.20 in 1938. Average production per man day has dropped from 1.12 in 1938 to 1.03 long tons in 1943. As a comparison, production per man day in the United States is approximately 5 long tons. The average day wage in the British mines is now a little aver $4; in 1938 the average day wage was about $2.25. Great Britain produced 227 million long tons in 1938 from their deep mines, and in 1943 production was 194.5 million, with an additional 4.5 million from strip mines. To meet present wartime needs, output is being supplemented by the production of strip- mined coal, an industry that did not exist prior to the war. Strip mining is now producing at the rate of 15 million long tons per year.

Jan 1, 1944

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 1400°F. (760°C.), the metal becomes non-magnetic, and at the "As point," 1670°F. (910°C.), it undergoes a change in crystalline form to become gamma iron. In the range 1400 to 1670°F., it is sometimes called beta (0) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 2550°F. (1400°C.), it changes into delta (d) iron, which is identical with beta or non-magnetic alpha iron. Pure iron melts (in a hydrogen atmosphere) at 2795°F. (1535°C.); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures. (1) For example, in heating through the As point a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 27 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always the case. For example, the specific heat reaches a sharp maximum at the A2 point although no transformation occurs. Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals which are liquid at the melting point of iron only lead, silver, and bismuth refuse to dissolve to an appreciable extent. The non-metals presumably dissolve by virtue of the formation of an iron compound; for example, sulphur is thought to dissolve as the compound FeS. However, there is no satisfactory method of proving that this

Jan 1, 1944

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

THE Fall Regional Meeting of the Institute, which has now for some years been held in cooperation with the Western Division of the American Mining Congress, will be held this year at Joplin, Mo., in the heart of the great Tri-State district. This year the Tri-State Zinc and Lead Ore Producers Association is joining in the meeting. The Society of Economic Geologists will also take part though not offering any papers. The district in which the meeting is held includes adjacent parts of Missouri, Kansas and Oklahoma. Out in the heart of a fertile prairie farming country, it is one of the major mining districts of the world. It produces normally approximately one-third of the zinc ore mined in the United States which is equivalent to nearly one-half the zinc since the concentrate has always been notable for the height of its grade. Even in the depressed business year 1930, the American Bureau of Metal Statistics credits the district with 434,460 tons of concentrates equal to 217,230 tons of zinc out of 1,503,095 and 576,630 respectively for the country as a whole. This was equal to about one-seventh of the world's output of zinc, more than that of any foreign country. In addition about 75,000 to 100,000 tons of lead is annually furnished by the same mines. Elsewhere we present a general description of the district prepared for this meeting by J. C. Heilman, a Lehigh graduate, who has spent the past eleven years there and has had charge of explorations for many of the companies.

Jan 1, 1931

By C. F. Willis

Many of the failures in vocational education are due to the fact that the educational methods were not designed to the capabilities, habits, and environments of those to be trained; rather they were based on the policy that education is education and lessons are lessons, whether for youngsters of fifteen or for men of forty. Vocational education among miners involves, first, a study of the men themselves, their habits, and the use of their leisure time; second, a study of the differences between the methods of teaching required for men and for children. Certain fundamental requirements of training methods for miners are reasonably universal and may be applied with success to any ordinary mining community. The rate of labor turnover is another consideration; it would be useless to design a four-year course for men who remain in one place only a few months. Length of Course The first consideration should be the length of the course. Few mining communities have a sufficiently stable population to make it possible successfully to carry on a course for over a year. While some men might complete a four-year course, the number is comparatively small compared with the number to whom a shorter course would be of service, and it is better to raise the standards of education even a little for a large number than to raise them to a high level for a few. It is perfectly possible to attain both objectives by arranging the courses in small units; all the units, when grouped together, should comprise a fairly complete course, yet any one unit should be complete in itself and of benefit to the workman. It should not take many of these units to make a miner or a timberman out of a mucker; but to do this the course should be short, because muckers seldom stay in one place long. By grouping a number of these units together it Would be possible for a miner to become a shift boss or a shift boss a foreman, and so on. As far as possible the units of the course should not be dependent on those preceding or following. The workman understands the completed job but he is not accustomed to carrying on several jobs at the same time and

Jan 1, 1920

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

CHARLES CATLETT, Staunton, Va. (communication to the Secretary*). -I hesitate to discuss in general terms a paper such as Mr. Wysor's, which bears evidence of so much careful and detailed investigation, yet it is the broad possibilities which his paper presents that are really attractive and his cautious conservatism may make us unappreciative of these possibilities. Mr. Wysor calls attention to the fact that the iron-ore mixture which he uses, carrying 0.28 per cent. of potash, is probably above the average. No doubt this is true, but on the other hand it may be very much less than the mixture at some blast furnaces or very much less than would be the case with special mixtures bearing the question of potash in mind. Unfortunately, iron ores are not ordinarily examined for potash, and with the ordinary analyst there is opportunity for very considerable error in the determination. The 10th Census gives 270 complete analyses of iron ore, on the accuracy of which we may rely. Of these, there are 21, or 8 per cent., that carry more potash than Mr. Wysor's mixture; 14 of these carry approximately twice as much, or more; eight carry approximately three times as much, or more; three carry approximately five times as much; one carries over seven times as much. It may be worth while to take some of the ores that are known to be high in potash and consider the possibilities in the light of Mr. Wysor's investigations.

Jan 5, 1917

INTRODUCTION Great emphasis has been given throughout this text to the necessity of maintaining the integrity of mineralogical populations when operating upon sample data drawn from mixed populations. Mineral deposits rarely are completely homogeneous and often consist of many subsets separated by geological and mineralogical boundaries. Sometimes different mineral populations are difficult to distinguish, and may be inadvertently lumped together-often without serious consequences, but more often with detrimental effects upon analytical results. The geologist must accept the responsibility for recognizing and recording mineral boundaries that may include: changes in mineral suites, lithological horizons, host rock types, faulted and offset segments, zones of enrichment or depletion, and several other geological and mineralogical changes that effect mineralogical structuring and distribution within a deposit. When employing conventional methods for assigning estimated values to irregularly shaped mineral inventory blocks, it was only necessary for the geologist or engineer to con- fine the block limits to the known geologic boundaries. Thus if a fault interrupted the mineral zone, the trace of the fault could be used as a block boundary. Intelligent decisions could always be made as to which blocks to include in each mineral population. However, with the advent of the computer, which per- mits the computation of mineral inventory blocks using better mathematical estimation techniques, there now enters the "boundary problem." Unless the computer can be programmed to recognize population differences and geologic boundaries, greater estimation errors will be found in computer-generated mineral reserves rather than in less sophisticated conventional inventories. Much disillusionment has been expressed over the years by experienced mineral appraisers as a result of their study of computer-generated inventories that failed to account adequately for geologic vagaries. Many, thus disillusioned, have concluded that computer techniques are not satisfactory, or have only limited applications to simple deposits. As with all problems in the mineral industry,

Jan 1, 1980

By B. W. Howlett, M. B. Bever, Somnath Misra

The heats of Formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 and the heats of solution of tellurium and selenium in liquid bismuth have been measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides have been measured in a constant temperature gradient calorimeter. The thermo-dynamic quantities are interpreted in relation to the stability of the compounds and the nature of the solid-liquid transition. THE selenides and tellurides of several elements of Group VB of the periodic system are of interest because of their electronic properties. The compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 are semi- conductors; they also have gained prominence in the fields of thermoelectricity and photoconductivity. However, little is known about their thermody-namic properties. As part of a research program on the thermo-dynamic properties of intermetallic compounds, the heats of formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 were measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides were measured in a constant temperature gradient calorimeter. The results, in addition to their intrinsic interest as thermodynamic quantities, contribute to an understanding of the stability of the compounds and the nature of the solid-liquid transition. 1) EXPERIMENTAL 1.1) Materials. Samples of the compounds SbzSe3 and Bi2Se3 were prepared by melting the elements in stoichiometric proportions in evacuated Vycor capsules followed by quenchinn in water. They- were then annealed in vacuum for 12 hr at 550°C. A sample of Sb2Te3, consisting mainly of one large grain, supplied by the Lincoln Laboratory,

Jan 1, 1964

Jan 1, 1896

By Ednlund D. North

Discussion of the paper of Edmund D. North, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 37, January, 1910, pp. 21 to 25. A. SCOTT REID, London, Eng. (communication to the Secretary*) :-As a constructor of several glass mine-models, I have read with much interest the description of the model of the Montana-Tonopah mine-workings by Edmund D. North. As an interchange of ideas and experience is always an advantage, and in view of the fact that such models are coming more and more into vogue, perhaps the following remarks on this subject may prove of interest to mining engineers generally and to Mr. North particularly. In the model of the Waihi gold-mine, New Zealand, which I constructed, a dust-proof case is used. The top, bottom, front, and two ends are of glass; the back only is of wood, painted a dull white, against which the mine-workings show very distinctly. Each mine-level is represented by a horizontal sheet of glass, supported on metal runners fixed to the uprights at each end of the case, in a manner similar to that described by Mr. North. The corner uprights are strengthened by having a metal band screwed to the inside face of each, to which the metal runners or supports for the sheets of glass are screwed in turn. The reason for having this additional strength is that as the mine is developed in depth, and fresh levels are opened, the increasing weight of the glass sheets, added to the model, caused the unsupported wooden uprights to bend slightly, so that the glass sheets-did not fit in with the desired nicety, and co-ordination was, to a considerable extent, lost. Strengthening the uprights in this manner is not important in models of mines in which only a few levels have been opened, or when the sheets of glass are small, but in the Waihi model there are 15 sheets of glass to be supported, and more to be added as development proceeds, and the weight is considerable.

May 1, 1910

By W. W. Odell

THE sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. So universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only- the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question.

Jan 9, 1919

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By Leonard C. Grimshaw

The idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a composite steel. Previous Methods There are two methods in use that result in tolerably good bonds between ferrous metals: (1) the casting method, and (2) what we shall call the "heat-pressure" method. This "heat-pressure" method covers processes in which the bond is made between two prepared surfaces by heating them and then applying pressure. Usually sufficient pressure must be used to produce appreciable spread and elongation, or else we arc merely brazing and not truly welding. Casting methods for welding together ferrous metals have been used more than 74 years, and are described in the technical literature as applied

Jan 1, 1936

By Leonard C. Grimshaw

The idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a composite steel. Previous Methods There are two methods in use that result in tolerably good bonds between ferrous metals: (1) the casting method, and (2) what we shall call the "heat-pressure" method. This "heat-pressure" method covers processes in which the bond is made between two prepared surfaces by heating them and then applying pressure. Usually sufficient pressure must be used to produce appreciable spread and elongation, or else we arc merely brazing and not truly welding. Casting methods for welding together ferrous metals have been used more than 74 years, and are described in the technical literature as applied

Jan 1, 1936

By F. C. Schora, H. P. Meissner

COUNTERCURRENT staged processes involving chemical reactions between solid and gas streams are becoming more common. Such operations are generally carried out in a series of fluidized beds with each bed acting as a stage. Fig. 1 is a schematic illustration of a series of stages located in a single column, with a solid stream moving down through this column from stage to stage counter to a rising gas stream. The reduction of iron oxides with hydrogen and carbon monoxide is one of the reactions which can be advantageously carried out in such a countercurrent system. Calculation of the performance of a countercur-

Jan 1, 1961