Search Documents

By A. Blake Caldwell

Tyrone-a complete mining and concentrating facility built by Phelps Dodge Corp.-straddles the Continental Divide where surface water on either side flows in opposite directions although all water is taken from and returned on the northwest side of the Divide. At the outset, Tyrone was saddled with a problem of an adequate water supply, and the Gila River some 23 miles distant appeared to be the logical source. This in itself presented a major obstacle to Phelps Dodge because of the distance water had to be pumped and because of an adverse head which had to be overcome between the Gila River and the two 4-million-gal-capacity terminal water supply tanks at the mill. Having acquired water rights on the Gila River and in order to control the seasonal fluctuations in water volume, the company built the Bill Evans, off stream, earth-filled dam. This reservoir will contain 2100 acre-ft of water when full and it was constructed by the Hamilton Construction Co. for Phelps Dodge. The dam impounds fresh water for the Tyrone plant's use and four vertical turbine pumps (4500 gpm each) lift the water 275 ft from the Gila River into the reservoir. Since construction, Phelps Dodge has optioned the lake to the New Mexico State Game Commission for recreational purposes. In addition to the lake, land around the reservoir has been optioned to the State Game Commission for public use. The lake has already been stocked with trout and by next summer some keepers should be available for the taking.

Jan 12, 1969

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples. Gaudin,1,2 the first to apply a nuclear reaction in detecting beryllium minerals, developed a method that irradiates the sample with gamma rays, which react with beryllium nuclei to produce neutrons. The neutrons are then measured with standard equipment. The cross section for this reaction is about 1 millibarn. The cross section is a measure of the probability that a reaction will take place, for example, between a beryllium nucleus and an incident gamma ray or alpha particles.3-5 At 1-millibarn cross section for the reaction, satisfactory performance required a source strength of the order of 1 curie (3.7 x 10"' disintegrations per sec, where each disintegration releases one or more gamma rays). The reactions will not take place if the gamma radiation is below a minimum energy, in this case 1.63 mev. The size of the source and the energy of the radiation made heavy shielding necessary for these experiments, both to reduce the background count of the neutron counter and to safeguard personnel. The original discovery of the neutron by Chad-wick in 1932 resulted from experiments with another nuclear reaction, induced by bombarding beryllium with alpha particles in which the products are carbon-12 and neutrons. The equation for this reaction is as follows:' " ,Be" + ,He'? 6C12 + 8,n' [1] re-particle neutron In the above nuclear equation (Eq. 1), the sub- script number indicates the number of protons in the nucleus (the atomic number) and the superscript the total number of neutrons and protons (approximately the atomic mass). For the alpha-neutron reaction the cross section is about 250 milli-barns, or 250 times that of the gamma-neutron reaction used by Gaudin. The positively charged alpha particle is repelled by the positive charge of the beryllium nucleus; it must, therefore, have a certain minimum energy in order to approach close enough to the beryllium nucleus to react. For reaction with the beryllium nucleus, the lower limit of the alpha-particle energy is 3.7 mev. The alpha-neutron reaction, with polonium-210 as an alpha source, was selected for the present experiments. Alpha particles are emitted by polonium-210 at 5.30 mev, which is adequate for the reaction with beryllium. Furthermore, this isotope of polonium emits alpha particles with negligible associated gamma radiation, thus eliminating the necessity of shielding. The half-life of polonium-210 is 138 days. Inasmuch as alpha particles carry a possible charge and are large compared with most nuclear particles, their energy is rapidly dissipated in passing through matter. Their range in standard air is 3.66 cm,3 and they penetrate only a few tens of microns into a mineral sample. The short range in air can be minimized by preparation of a flat sample surface that can be brought very close to the alpha source during analysis. On the other hand, short range of alpha particles in air lessens the radiological health hazard and makes it possible to use this method without shielding. It must be emphasized, however, that the alpha emitters are potentially very dangerous if they enter the human body. Polonium must be handled with extreme caution. The literature has reported experiments on the yield of neutrons from reaction of alpha particles with beryllium nuclei. Feld" reports that in intimate mixtures of polonium and beryllium, 3 x 106 eutrons per sec are produced per curie of polonium. Elsewhere in the same reference it is stated that a sandwich-type source yields about one third as many neutrons as an intimate mixture. A table of neutron yields for full energy polonium alpha-particles on thick targets as reported by Anderson7 is the basis of Table I. From Table I it can be deduced that the elements most likely to interfere, i.e., those that also produce neutrons when bombarded by alpha particles, are boron and fluorine. These data also show that it will probably not be possible to determine very small quantities of beryllium in rocks because of the masking effects of the major elements, sodium, magnesium, and aluminum. The neutrons emitted in the alpha reaction are detected by another nuclear reaction. Either of the

Jan 1, 1960

By E. W. Rouse

THE year 1936 has seen rehabilitation of many plants which had been closed or severely curtailed. The Steptoe smelter of the Nevada Consolidated Copper Co. has been transformed by a rearrangement of the flow of material and utilization of mechanical handling to a maximum. The Phelps Dodge Corp. reports the construction of newer and better reverberatories at the Copper Queen smelter, and of particular interest, a single high-pressure waste-heat boiler placed directly over the uptake. There has also been a complete reconstruction of the smelter at the Laurel Hill plant of the Nichols Copper Co.

Jan 1, 1937

By Norman D. Fitzgerald

IN 1943 the petroleum industry completed a series of practical adjustments to the acute problems which dominated the scene a year earlier. The crisis in petroleum transportation from the Gulf Coast to the East Coast was met by the completion of overland pipe lines supplementing emergency haulage by tank car so pressure on consumers along the Atlantic Seaboard was appreciably relieved. Later in the year when the western Atlantic was largely cleared of submarines, the sharp reduction in the hazards of marine transportation permitted the resumption of coastwise traffic and imports from South America. Nationwide restrictions in the use of gasoline and fuel oils became necessary as military demands for all petroleum products mounted to high levels.

Jan 1, 1944

By C. W. Robinson

Transportation is the minerals business. Once upon a time the geologist, the engineer and later the metallurgist reigned supreme, but the leading role in mineral development today is the economist-especially the transportation economist. Obviously this trend is more important for large volume, low value mine-to-market movements of such commodities as iron ore, phosphate, potash, coal and petroleum. But, transportation is of sufficient importance to all mining activities to be included in forward planning. Civilization has been influenced by transportation developments to an extent little understood or appreciated. Although industrialists are capable of intelligent historical analysis of this phenomenon, too frequently they have failed to project, or anticipate those changes in transportation techniques which will influence the pattern of industrial growth.

Jan 1, 1971

By TSUYEE PEI

I FEEL greatly honored and appreciate this opportunity to be able to say a few words about that rather perplexing subject, silver. The constant decline in the price of this metal has now reached the stage where it is of much concern and the cause of serious discussion among the leading financiers, economists, and statesmen of the world. Further- more, it is significant that this subject is so important that almost every day one can read articles pertaining to it in the newspapers and trade publications. Being essentially a banker, and not an economist, I do not claim to be an authority on the silver question. These remarks are merely some of my observations in, regard to the many puzzles which-I came across in my recent studies of this very important question.

Jan 1, 1931

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By W. A. Boyer, A. W. Beck

At the Morning mine of American Smelting & Refining Co. it was particularly important that there be a means of signaling the engineer from the moving cage in the shaft. Because of the shifting ground in which the shaft was located, buckling timber made it extremely difficult to keep a continuous bell line serviceable. In 1930 engineers considered a moving contact pantograph arrangement between the cage and two stationary messenger wires strung on insulators in the shaft compartment next to the cage. The idea was abandoned because falling material in the shaft and speed of hoisting made it difficult to maintain communication. Later in 1934 a manufacturing company was consulted about the use of an electric eye or a radio signal. As the shaft was located in a return air stream of nearly 100 pct relative humidity, there was too much fog for the electric eye to be used. The radio signal was considered, and it was believed feasible to generate electric static on the cage, locating a radio receiver at the top of the shaft, but the manufacturing company's research department was too busy to work on it at that time.

Sep 1, 1955

By William Newton Best

Oil burners, oil furnaces, and methods of installation, have been the subject of many articles, but information concerning oil-burning systems, based upon scientific principles, is still in great demand, especially in the manufacturing districts of our country. Fuel oil, as it is termed (this being the residuum from oil refineries), has for many years been of great service to our manufacturers, and has justified its popularity not only by producing a superior manufactured product, but by turning out approximately 50 per cent. more product than can be made with coa1 fuel under like conditions. To install a system requiring only an oil-storage tank, a small pump, and an oil-supply main with numerous laterals leading to the various burners, furnaces, boilers, etc., is a comparatively simple matter; and, because fuel oil is very volatile, it is not necessary to heat it, even during the winter months in a very cold climate. Furthermore, only a small amount of power is required to atomize fuel oil, this often being done by a positive pressure blower, or by a mechanical burner. An analysis of fuel oil, together with that of various other liquid fuels, is given in Table I.

Jan 1, 1915

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By C. K. Leith

THE interdependence of nations in regard to mineral supplies has grown apace with the expanded needs of industry, with depletion of reserves, and with advances in technology. This increased mutual dependence raises many questions of foreign economic policy of special importance in our postwar planning. Realization of the urgent need for the development of a general mineral policy broadly based on national requirements led to discussions of the problem between officials of the Department of State and myself, as a result of which it was suggested that I make an informal and unofficial canvass of the views of mineral specialists of the country on foreign mineral policy.

Jan 1, 1946

By Thomas Lane Carter

THE history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development ?of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers ill the mines which the white men started. The Kaffirs of South. Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man's civilization. They are a virile race, and so far the vices of civilization have not killed. them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent-have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribe's in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country, are much finer workmen than the degenerates from less favorable sections: It is universal in South Africa to speak. of the .Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a " boy," and in this paper the word " boy " is synonymous with Kaffir.

Nov 1, 1908

By D. A. Dahlstrom

Although the liquid-solid cyclone is a relatively recent innovation in the field of coal preparation, various authors have already indicated three distinct applications to operations encountered in the modern tipple. Driessen's articles and work at the Dutch State Mines exhibited its possibilities in the beneficiation of fine coal with apparently high efficiencies down to the 200-mesh fraction. 1 2 3 4 Other publications point out its use as a recoverer, thickener, and preliminary dewatering agent of fine coal which in too many cases is being wasted due largely to former high operating cost limitations 5 6. Finally, certain authors have emphasized the practicability of applying the cyclone to the elimination of coarse and fine solids from water slurries in the tipple in order to produce a water suitable for recycle purposes containing only minute particles far below the 200-mesh size.6 This would result in a closed water system for many cases, with its accompanying economic and operating advantages to locations where water quantity and quality problems are severe; better operation of washing equipment using a consistent water devoid of injurious fine particles; lowered maintenance costs due to the lesser abrasion resulting when the fine abraiding particles are removed; and the greater ease of disposing of refuse streams of reduced volume containing greater percentages of solids.

Jan 1, 1949

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State's production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

By AIME AIME

THE list of deaths during the year 1906 comprises the following names, the figures in parentheses indicating the year in which the persons named were elected to membership Members and Associates.-Arthur Vaughan Abbott (1882), William Anderson Akers (1889), R. Scott Allen (1905), George H. Arlett (1900), Thomas Septimus Austin (1883), Thomas T. Baker (1887), William Tittley Batchelor (1902), Charles Lowthian Bell (1897), Edgar Vallentine Bensusan (1892), George Lothrop Bradley (1874), Ernst Elmer Breisch (1896), Horace F. Brown (1895), James A. Burden (1876), Alexander B. Coxe (1880), George A. Crocker (1879), Albert W. Fiero (1886),

Jul 1, 1907

By William F. Boericke

RESEARCH in the modern refractories laboratory has two practical ends in view-to develop refractory materials for the metallurgist that will meet particular operating difficulties more effectively and to ?manufacture these refractories at a cost sufficiently low to make their use economical to the metallurgist. At the research laboratories of E. J: Lavino and Co., at Plymouth Meeting, Pa., the technical staff, under Dr. Gilbert E. Seil, is giving principal attention. to an. exhaustive investigation of the following factors in refractories:

Jan 1, 1931

By T. H. Weldon, L. V. Whiton, R. R. McNaughton, J. H. Hargrave

Oxygen enriched air is being used quite extensively in the metallurgical plants of The Consolidated Mining and Smelting Co. of Canada, Limited, at Trail, B.C. The oxygen used for this purpose is a by-product from the Company's chemical plants located in the area. Most of the ore treated in the Trail metallurgical plants comes from Com-inco's Sullivan Mine at Kimberley, B.C. At Kimberley the ore is milled to produce lead and zinc concentrates which are shipped to Trail for further treatment to metal. One section of this paper deals with the use of oxygen enriched air in the suspension roasting of the zinc concentrates. In this process the concentrate is calcined for leaching preparatory to electrolytic recovery of the zinc. A second section of the paper describes the use of oxygen enriched air in operations at the lead smelter. There oxygen enriched air is used in the blast to the lead blast furnaces and in the slag fuming furnace which recovers the lead and zinc contained in lead blast furnace slag. The final section of the paper outlines the precautions necessary for the safe use of oxygen enriched air in any plant operation. The Use of Oxygen Enriched Air in the Suspension Zinc Roasters The suspension roasting of zinc concentrate developed at Trail, B.C., has been described in AIME Vol. 121, "The Electrolytic Zinc Plant of The Consolidated Mining and Smelting Company of Canada, Limited" by B. A. Stimmel, W. 11. Hannay and K. D. McBean. Since the publication of that paper, the use of oxygen enriched air in suspension roasting has been introduced as regular practice with marked advantage. The relative importance of a specific advantage may vary with changing conditions, but, in general, it may be stated that improved operation has been achieved at increased capacities. Suspension roasting is carried out at Trail in converted standard 25 ft diam Wedge roasters. The 2nd, 3rd, 4th and 5th roasting hearths have been removed and the drying hearth covered over. Drying of the concentrate is done on the drying hearth and the 1st roasting hearth. The dried concentrate, after any lump's have been broken up in a ball mill, is fed to a single burner located in the upper part of the combustion chamber. Oxygen is introduced at the burner fan along with the gases from drying, returned combustion gases from the waste heat boiler outlet and the required amount of new air. Up to 60 pct of the concentrate settles out on the 6th roasting hearth, the rest passilig out of the roaster. The product collected in the waste heat boiler is finished calcine, but the dust collected in the cyclones after the boilers is returned to the base of the combustion chamber where the sulphate is decomposed. Gases from the c'yclones go to a Cottrell precipitator. The discharges from the 7th roasting hearth and the waste heat boiler are combined with the Cottrell dust to give the finished calcine. Following small scale tests started in 1933, oxygen enriched air has been used continuously in the suspension roasting of zinc concentrate in Trail, beginning in 1937. A significant factor in promoting its use in this operation was the availability of by-product oxygen from the Company's near-by Chemical and Fertilizer Division. To-day it is standard practice at Trail to use oxygen enriched air for zinc concentrate roasting. The most important requirement in roasting a zinc concentrate for an electrolytic plant is that the zinc in the calcine should have maximum solubility. It is also desirable at Trail that the gas produced for the manufacture of suhhuric acid should have a ~naximum concentration of SO2 and that a substantial recovery of waste heat from the gas be achieved. High solubility of zinc requires that the sulphide sulphur and zinc ferrite in the calcine be kept low. These are both functions of temperature and time, with formation of zinc ferrite also dependent on contact between the iron and zinc particles. One of the inherent advantages of suspension roasting is that minimum time and contact are achieved. The limit on temperature is imposed by the fusion point of the concentrate and not by the need to control zinc ferrite formation. Operating temperatures are normally maintained within the limits of 1725" and 1850°F. A relatively low zinc sulphate in the calcine is required at Trail, and this results from discharging the calcine from the high sulphur dioxide atmosphere at a temperature above 1600°F.

Jan 1, 1950

By H. M. FRENCH

ARC welding can be defined as a process whereby two A pieces of metal are brought together, heated to a molten state by the heat of an electric arc, and fused into one piece. There are several kinds of arc welding: the metallic arc, the carbon arc, the atomic hydrogen arc and the shielded arc methods. A short description of each, together with its major applications, will serve to distinguish between them. Metallic arc welding involves an arc drawn between a metal electrode and the material to be welded, called the work or the "parent metal." It may be further subdivided into hand and automatic welding, depending on whether the electrode is fed to the arc by hand or by motor drive. This form of arc welding can be applied to most welding operations. Exceptions to its use consist of applications where very thin metals are to be welded; where it is desired to join the work with- out adding metal; or where extreme ductility may be required:

Jan 1, 1930