Search Documents

THE slag performs two useful functions in open-hearth steel- making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) Si02, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (Si02 and P205). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined; and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1964

By Edwin Chance

DURING the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that 'can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by, bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these

Jan 4, 1916

By H. C. Fiedler

X HE development of the cube-on edge secondary re-crystallization texture in Si-Fe strip requires that normal grain growth be restrained. It has been shown that the degree of restraint and hence the completeness of secondary recrystallization depends upon the size and number of second-phase particles, which in turn is dependent upon the prior processing history.1y2 The purpose of this note is to show that, for heats in which manganese sulfide particles are providing the restraint to grain growth, the choice of hot rolling temperature depends upon the manganese content. The making and processing of the heats to the final gage of 0.012 in. has been described.3 The compositions are given in Table I. Apparent in Fig. 1 is the decrease in the ability of strips hot-rolled from 1175°C to undergo secondary recrystallization as the manganese content increases. It has been shown that 1175°C is below the solubility temperature of 0.014 pet S in even the 0.038 pct Mn alloy: and the observed behavior is attributed to an increasing fraction of the sulfur forming large manganese sulfide particles at the heating temperature for hot rolling. This fraction of the sulfur is thus unavailable to subsequently form the small, uniformly dispersed particles which are needed to restrain normal grain growth. Since the sulfur is completely in solution at 1325°C,3 strips from all three alloys show strong secondary recrystallization behavior when hot-rolled from that temperature.

Jan 1, 1969

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By Hugh Roberts

During 1916 and 1917, the E. J. Longyear Co. of Minneapolis, Minn., carried out a campaign of exploration for nickel-copper ore in the Sudbury District of Ontario. The work was initiated by W. E. Smith, a resident of Sudbury, who called the attention of W. J. Mead, Chief geologist. The E. J. Longyear Co., to the fact that explorable lands in the Sudbury District were still available. Five diamond drills were employed, and holes were drilled in the townships of Levack, Trill, Denison, Blezard; Garson, Falconbridge and MacLennan. The general map of the District, Fig. 1, shows the distribution of the lands chosen. As a result of this exploration, a large body of nickel and copper ore has been found in the western part of the Township of Falconbridge. This property lies in the eastern part of the Sudbury District, east of the Garson mine.

Jan 2, 1918

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By Zay Jeffries

IT HAS been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat and cooling either rapidly or slowly with nearly pure iron and slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point, which is near 700° C. The present paper will not consider these old and well-known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, in 1886, reports that both working steel and heat treatment of steel in the blue-heat range are highly injurious. Recently, however, some metallurgists believe that the straightening of warped steel forgings at a blue heat produces a beneficial effect on the metal.2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes -in Iron and Steel Below the Thermal Critical Range, which has the following personnel: R. R. Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F.C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood: This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 2, 1920

By C. Norman Cochran

The pllnse diagvam for the NaF-AlF3 system was used to calcutate an ionic model for the NaF-AlF3 system. Assuming an ideal solution,a series of simultaneous equations expressing equilibria be-tween solid and liquid phases at the euleclic, perilec-tic, and melting points were solved for the activities of the ionic species, the dissociation constants, and the entropies and heats of fusion. The calculations suggest the existence of A13F1415 ions in addition to the F-1+AlF6-3 , and AlF4-4 ions previously proposed by others. The calculaled valnes give better agreement with vapor pressures than the previous model without Al3Fl14-5. Additional possible vefinements of the model are proposed. CRYOSCOPIC1 investigations and density data2 for the NaF-A1F3 system have previously been used to study the dissociation mechanism of Na3A1F6 and to derive equilibrium constants for its dissociation to NaF and NaAlF,. Depending primarily on the heat of fusion assumed for cryolite, the dissociation constants ranged between 0.02 and 0.18 from cryoscopic studies, and from 0.09 at 1273°K to 0.16 at 1363°K from density data. In most cases the values were unable to reproduce satisfactorily the experimental liquidus lines very far on the A1F3 side of the Na3A1Fe composition. This suggested the existence of at least one other ionized compound in the melt besides NaA1F4 in the Na3A1F6-A1F3 side of the system. This is assumed to be liquid Na&13F14 (chiolite), which is already established as a stable solid in phase studies of this system. MODEL FOR THE MELT The melt is assumed to be an ideal solution with ion activities equal to anion fractions. The only cation in the model is sodium so that Temkin and simple anionic activities are identical. Although the compounds are completely ionized to Na' and the respective anion in the melt, molecular rather than ionic notation is used throughout this work. The Na3A1Fe is assumed to dissociate to NaA1F4 and NaF as in the former model, and Na&13F14 to dissociate to Na3A1Fe and NaA1F4. Other valid dissociation equilibria can be written involving these four compounds, but all of these can be obtained by combinations of the two described dissociation reactions and, thus, are automatically considered in these calculations. The model allows for no free AlF3 so that compositions for NAIF3 > 0.5 (mole fraction A1F3 on the NaF-A1F3 basis) cannot be treated. The question of the existence of free AlF3 in the melt will be discussed again later. The constants in the model were evaluated from points along the entire known liquidus line of the NaF-A1F3 system. Previous work employed only the liquidus line or densi- ties near the Na3A1F, composition. The liquidus line compositions used in the solution of the model are from unpublished work by Mr. P. A. Foster, Jr., for compositions between the Na3A1F6 melting point and the Na&13F14-A1F3 eutectic, and from the published works of Grjotheim,1 Phillips,3 and Foster4 for the remainder of the system. The relationships used in solving for the desired dissociation constants and heats and entropies of fusion are listed in Table I, and the points along the liquidus line at which each apply are indicated to the right of the relationships. The mole fractions of each of the separate species in the melt are symbolized by N. Relationships [I] and [2] are the respective dissocia-ation constants, Kl and K2, of Na3AIF6 and Na5A13F14 for this model. For simplicity, these constants will be assumed to be independent of temperature. Relationship [3] follows from the assumption of the ideal solution. The expression relating the values of N to the experimental values of NAIf3, is given in Relationship (41. Relationships [5], [6], and [7] each state the equilibrium between a compound in the melt and its pure solid phase for the portion of the liquidus lines where it precipitates. The heats of melting, AH,, and entropies of melting, AS,, used in [5], [6], and [7] are assumed to be independent of temperature. The compositions and temperatures of all five invariant points (two melting points, two eutectics, and one peritectic) along the liquidus lines from NAIF3 = 0 to NAIF3 = 0.5 were employed in the solution. The eutectic and peritectic compositions were particularly useful because each of these is involved in one more equation than other points along the liquidus lines and thus reduces the number of points required to solve for the constants. Also, their use assures that the inflection points in the derived liquidus line will correspond exactly with those on the experimental liquidus line. The total number of equations is 5k1 — 1, where n is the number of experimental composition points used. The number of unknowns is 4n + 5 (4n- 3 values of N, 3 values each of AH, and AS,, and 2 values of K). Thus, six points must be used in the solution to obtain an equal number of equations and unknowns. The one additional required experimental composition was taken on the liquidus line between the Na3A1Fe melting point and the Na3A1F6-Na5A13F14 peritectic. Previous work indicated this was a difficult portion of the curve to fit. The temperature used for the point was 1161°K, the same as for the NaF-Na3A1Fe eutectic. This choice of temperature gave two points with identical NNa3AIF6 values which simplifies the algebraic solution. The second point at this temperature is denoted 1161°'K. PROCEDURE FOR SOLUTION OF EQUATIONS Values were assumed for NNa,AIF and NNaF at the NaF-Na3A1F6 eutectic at 1161°k. By an iterative procedure, the corresponding values for NNa5A13F14 and NNaAlF4 at 1161°K were determined from 131 and 141. A value was assumed for NNaAlF4 at 1161°'K and

Jan 1, 1968

By Ralph E. Hartline, Wilfred Tapper

The Strataflow process for locating water entry in producing, wells is now available. This method as now practiced utilizes the fact that fluids of different salinities have different electrical resistivities. By introducing into the well a fluid of a markedly different salinity than that of the fluid being produced, a pronounced resistivity change will occur at the point of entry. By running a Strataflow survey the points of major and minor water entry may be interpreted from changes in the resistivity of fluid in the hole. Strataflow results are obtained with the well operating under almost normal producing conditions, and are a logical primary step in any workover program, having as its purpose shutting off of the water. INTRODUCTION Water production is a serious problem in many producing oil wells. It certainly increases lifting costs and in some cases presents a disposal problem. It often aggravates corrosion problems and can even endanger oil production. With accurate information to guide an effective workover program, many marginal wells could be restored to Profitable Production. The shortcomings of previous meth- ods of water entry location were recognized. The Strataflow process is the result of several years of development and field testing directed toward overcoming these limitations. It represents the continued development of a process reported by Silverman and Brown. The earlier work established the basic soundness of fresh-to-salt water resistivity contrast in delineating zones of water entry, but its application was limited by the difficulty of maintaining static balance of the well during preparation for the test. A more serious deterrent to its use, however. was its unadaptability to existing well logging service equipment and field operating methods. STRATAFLOW PRINCIPLE The general principle of the new method involves, first, conditioning the well by displacing the fluid in the bore of the well adjacent to the zone to be tested by a conditioning fluid which is miscible with the formation fluid. This displacement is carried out without interruption of the well production. The conditioning fluid must have some measurable physical, chemical, nuclear, or electrical property which is distinctive from that of the formation fluid. As the well continues to produce. formation liquid entering the well bore dilutes the conditioning fluid so that zones of entry may be determined by making a log of the property undergoing change. This general principle may be applied to indicate zones of either water or oil entry by suitable selection of conditioning fluid and proper logging equipment. The Strataflow process, as it is currently practiced for water entry location, uses fresh water as the conditioning fluid and depends for its operation upon the marked difference of electrical resistivity between this fresh water and the salty water produced by the formations. If possible. any necessary modifications of the well equipment are made a week or so before the test. The well is then returned to normal production. On the day the test is to be carried out. the conditioning water is landed at the bottom of the well and the test is made without interrupting production except for a brief period required for the conditioning water to consolidate into a continuous column extending to a point well above the test section. With this general description of the process in mind, a more detailed step-by-step description of the process will be clearer. PRELIMINARY PREPARATION OF WELL The Strataflow survey, as it is currently practiced for water entry location, is applicable only to pumping wells. Since the required electrical measurements are made by a special

Jan 1, 1952

By C. R. Claus, G. A. Standish

Since March. 1945, the Magnolia Petroleum CO. has drilled 39 wells in Southwest Coastal Louisiana. All wells were drilled within a comparatively small radius, but the area provides a large variety of problems. The deepest well drilled was 13,518 ft, and the total depth averaged 10,977 ft. Throughout this period drilling mud control and types of mud handled were: (I) phosphate, (2) red lime (late conversion), (3) red lime starch (early conversion), (4) red lime starch oil emulsion, (5) precision controlled low alkalinity-low lime content. and (6) gel muds for completion purposes. Improvement has been obtained in effecting some or all of the following: (I) more rapid penetration, (2) reduction in drilling hazards, (3) better evaluation of cores and logs, and (4) better completions. The geological sequence of zones penetrated range from recent sediments at the grass roots through the Frio section. Anticipation of high-pressure zones and incompetent formations entails precision control of drilling mud weights, and the unconsolidated nature of the various zones requires constant attention to the filtrate, viscosity, and gel strength values. In the Chalkley field, particularly, this combination of problems exists, where the formation pressures and overburden weight density values are in very close proximity. Design of casing and drilling mud programs must be modified to fit each well. INTRODUCTION Field and research work on drilling fluids has made constant progress, enabling operators to prospect progressively deeper horizons. Numerous papers have been written on the theoretical aspects of drilling fluid devel- opment, but in the field engineers have found it difficult to evaluate the role of specific mud constitutents when dealing in terms of thousand barrel mud systems. For that reason field data is somewhat lagging in technical report writing. However, applications of new techniques in the field have usually paralleled, and in numerous instances preceded, research work. The information obtained by Magnolia Petroleum Co. in the course of drilling 39 wells within a comparatively small area in Southwest Coastal Louisiana provides an excellent opportunity of reviewing a specific example of drilling mud evolution. A large variety of problems has been coped with, the most important result being that every well was successfully drilled to its projected total depth. The discussion begins with the advent of deep drilling in this area in March, 1945, and is concluded with a resume of recent drilling operations in the Chalkley field. The primary purpose of this paper is to describe the evolution in types of drilling fluids as it occurred and its application in the solution of various drilling problems. All of this information and experience resulted in the successful drilling of the three wells in the Chalkley field, where a combination of the most sound techniques was necessary in carrying drilling operations to the projected total depths. Other operators along with service company engineers have contributed considerably through the interchange of ideas and information to this paper, but the data and conclusions which are contained are based on first-hand observation of Magnolia Petroleum Company's drilling operations. The 39 wells drilled by Magnolia Petroleum Co. average in depth 10,977 ft per well, while the maximum depth penetrated was 13,518 ft. The cost of drilling fluids have varied from $8,700 to $165,000, with the over-all drilling costs ranging from $74,000 to $543,000 per well. This wide variance illustrates the unpredictable nature of each well and the effects on over-all cost when high density muds are required to control

Jan 1, 1955

By S. LeFevre

THE solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covers briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results.

Jan 2, 1915

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By Robert K. Waits

The resistivity, temperature coefficient of resistance, stability at 200°C, and structure of annealed Si-Cr films have been studied as a function of film cowposition. Colorimetric analyses of the films indicated 20 to 60 wt pct Cr over the resistivity range of 1 to 10-4 ohm-cm. Resistors were delinealed by photolithographic etching, contacted with aluminum, and mounted in TO-5 packages. The average temperature coefjicient of resistance, a, between 50" and 150°C is related empirically to the film resistivity, p, by a (ppm per °C) = -2900 - 1140 log p (ohm-cm). Near a resistivity of 3.5 x 10-3 ohm-ctn (30 at. pct Cr) , the temperature coefficient changes from positive to negative. The temperature at which the resistance maximum occurs increases with decreasing resistivity. The conduction mechanism between —196" and +360 C appears to have two components—an activated conduction dominating a1 lord chromium content and higher temperatures and a linearly temperature-dependent conduction dominating at high chromium content and low temperatures. Electron diffraction patterns showed the films to consist of Cr3Si and amorphous silicon. Resistors thicker than 150A typically drifted less than 0.6 pct after 5000 hr stor-age at 200°C. Resistors as thin as approxinzately 80°A that had a silicon overlayer showed similar stability. Such films had sheet resistivities of 10 kilohm per square and temperature coefficients near —600 ppm per "c. THIN-FILM resistors having sheet resistivities greater than 1 kilohm per square are required in many integrated circuit applications. A process for producing such resistors should be compatible with present circuit fabrication and packaging, including exposure to maximum temperatures of 300° to 570°C during contact alloying, die-attach, and ceramic package sealing. In addition, the resistors should have a low temperature coefficient of resistance and change less than 1 pct during storage at temperatures up to 200°C for 1000 hr or longer. Reports of work beginning in 1949 at Battelle Memorial Institute indicated that, among other materials, the silicides of chromium, Cr-Co, molybdenum, tantalum, and tungsten were worthy of further study as high-stability resistive films. Later work on Si-Cr films vacuum-deposited by flash evaporation from a tungsten boat1 led to the conclusion that Si-Cr had "excellent properties for development into high- stability ... resistive elements". More recently, Si-Cr films have been vacuum-deposited from a tantalum boat,2 from a BeO-coated tantalum boat,3 by flash evaporation from an electron-beam-heated tungsten Source,4 and by triode sputtering.5 This paper describes a study of Si-Cr films vacuum-deposited by electron-beam heating of Si-Cr alloys. Resistivity, temperature coefficient of resistance, stability at 200°C, and structure were studied as a function of film composition. EXPERIMENTAL PROCEDURE Film Deposition. Si-Cr sources were prepared by vacuum-melting pressed pellets of mixtures of powdered chromium (99.9 pct, -100 mesh, Lunex Co., Pleasant Valley, Iowa) and silicon (99.99 pct, -325 mesh, United Mineral and Chemical Co., New York). A permanent-magnet focused electron-beam gun having a water-cooled copper crucible was used to heat the pellet until complete melting occurred. The mixture was then kept molten for an additional 5 min. The alloy thus formed was used as the source material for Si-Cr film depositions using the same electron-beam gun. Pieces of semiconductor-grade silicon ingots were used as sources for silicon depositions. The films were deposited within a standard vacuum evaporator having an 18-in.-diam Pyrex bell jar, a liquid-nitrogen-cooled trap, and a Consolidated Vacuum Corp. 6-in. diffusion pump containing Dow Corning DC-705 pump fluid. The substrates were thermally oxidized* silicon wafers 2 to 2.5 cm in diam. The

Jan 1, 1969

By K. L. Williamson, P. W. Dugan

INTRODUCTION In recent years there has been increased social awareness and government attention directed toward the mining industry. The growing influence of the Occupational Safety and Health Administration (OSHA), the Mine Safety and Health Administration (MSHA), and the Environmental Protection Agency (EPA) has resulted in volumes of regulations governing a multitude of health and safety aspects of mining and milling. These regulations naturally have had an impact on new plant design and in some cases have necessitated retrofitting of existing plants. This paper will not examine the regulations governing the industry, since they are a matter of public record, but rather will address two specific health considerations, dust and noise, and their influence on the design of crushing and screening plants. DUST AND NOISE CONCEPTS Dust is generally defined as finely divided solids which may become airborne without any physical or chemical change except fracture. Since the purpose of comminution circuits is to reduce the size of solids by fracture, a percentage of the material is normally reduced in size to a point where it can easily become airborne. The major cause of dust becoming airborne is the air induced by falling material. When granular material falls through a distance, the induced (or entrapped) air rushes out available openings, carrying with it the fine particles that have become suspended. For this reason, the major points of dust generation are the points where the material is falling: chutes, transfer points, screens and equipment feed and discharge points. The expected dust concentration in an area is a function of the degree of size reduction (i.e., finer particles are more readily carried by air currents than heavier particles) and the volume of air that is induced. The measured dust concentration values for various operations agree with this

Jan 1, 1982

By E. O. Jones, E. Whitehead

During the heating of cold-worked nickel silver, the tendcncy of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. Changes in Alloys During Heating and Cooling During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting1 suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320" C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 1, 1926